Model SR601 - Chauvin Arnoux Group
Contents
1. AC Current Probe Models SR601 and SR604 User Manual DESCRIPTION The SR601 SR604 Cat 2113 43 2113 44 are designed for use in industrial environments The ergonomic design allows them to easily attach to cables or small bus bars The circular jaws guarantee a very good accuracy and low phase shift The probes have a measurement range up to 1000Arms continuous and are compatible with any AC ammeter multimeter or other current measurement instrument with an input impedance lower than 5Q To achieve the stated accuracy use the SR601 SR604 with an ammeter having an accuracy of 0 75 or better WARNING The safety warnings are provided to ensure the safety of personnel and proper operation of the instrument Read the instruction completely Use caution on any circuit potentially high voltages and currents may be present and may pose a shock hazard Do not use the probe if damaged Always connect the current probe to the measuring device before it is connected around the conductor Do not use on non insulated conductor with a potential to ground greater than 600V CAT III pollution 2 Use extreme caution when clamping around bare conductors or bus bars Before each use inspect the probe look for cracks in housing or output cable insulation Do not use clamp in wet environment or in locations that hazardous gases exist Do not use the probe anywhere beyond the tactile barrier INTERNATIONAL ELECTRICAL SYMBOLS o This sy2. RUMENTS 4 37 141mm 3 98 101mm 2 25 57mm 34mm Tactical Barrier keep hands below this barrier 1 71 43 5 mm 3 90 99 mm SR601 SR604 x je ELECTRICAL SPECIFICATIONS Current Range 0 1 to 1000A AC continuous cycle lt 1kHz Transformation Ratio 1000 1 Output Signal 1mA AC A AC 1A AC at 1000A Accuracy and Phase Shift Primary current 200A 1000A 1200A Accuracy 75 0 5 0 5 Phase shift 0 75 0 5 0 5 Primary current 0 1 to 10A 10A 50A Accuracy lt 3 0 1A 3 1 5 Phase shift N A 3 1 52 Reference conditions 23 C 3 K 20 to 75 RH 48 to 65 Hz external magnetic field lt 40 A m no DC component no external current carrying conductor test sample centered Load impedance 5Q Overload 1200 A for 40mn on 20mn off Accuracy Per IEC 185 Frequency Range 30Hz to 5kHz current derating above 1 kHz using the formula 1000A x 1 F in kHz Load Impedance 50 max Working Voltage 600V CAT III Common Mode Voltage 600V CAT III Open Secondary Voltage lt 25V by limiting circuit Influence of Adjacent Conductor lt 1mA A AC Influence of Conductor in Jaw Opening 0 1 of reading Influence of Frequency From 30 to 48Hz lt 1 of R From 65 to 1000Hz lt 0 5 of R From 1kHz to 5kHz lt 1 of R MECHANICAL SPECIFICATIONS Operatin
3. avoid electrical shock do not attempt to perform any servicing unless you are qualified to do so e To avoid electrical shock and or damage to the instrument do not get water or other foreign agents into the probe Cleaning To ensure optimum performance it is important to keep the probe jaw mating surfaces clean at all times Failure to do so may result in error in readings To clean the probe jaws use very fine sand paper fine 600 to avoid scratching the jaw then gently clean with a soft oiled cloth REPAIR AND CALIBRATION You must contact our Service Center for a Customer Service Authorization number CSA This will ensure that when your instrument arrives it will be tracked and processed promptly Please write the CSA on the outside of the shipping container Chauvin Arnoux Inc d b a AEMC Instruments 15 Faraday Drive e Dover NH 03820 USA 800 945 2362 Ext 360 603 749 6434 Ext 360 repair aemc com Or contact your authorized distributor NOTE All customers must obtain a CSA before returning any instrument TECHNICAL AND SALES ASSISTANCE If you are experiencing any technical problems or require any assistance with the proper use or application of this instrument please contact our technical hotline 800 343 1391 508 698 2115 techsupport aemc com LIMITED WARRANTY The current probe is warranted to the owner for a period of one year from the date of original purchase against defects in manufa
4. cture This limited warranty is given by AEMC Instruments not by the distributor from whom it was purchased This warranty is void if the unit has been tampered with abused or if the defect is related to service not performed by AEMC Instruments Full warranty coverage and product registration is available on our website at www aemc com warranty html Please print the online Warranty Coverage Information for your records eee 00 AN 100132 v10 07 13
5. eads set of 2 5ft safety 1000V Cat 2111 29 Banana plug adapter to non recessed plug Cat 1017 45 OPERATION Please make sure that you have already read and fully understand the WARNING section on page 1 Making Measurements with the AC Current Probe Models SR601 SR604 e Connect the black lead of the current probe to common and the red lead to the AC current input on your DMM or other current measuring instrument Select the appropriate current range 2A AC range Clamp the probe around the conductor to be tested with the arrow pointed toward the load If the reading is less than 200mA select the lower range until you obtain the best resolution Read the value display on the DMM and multiply it by the probe ratio 1000 1 If reading 0 659A the current flowing through the probe is 0 659A x 1000 659A AC e For best accuracy avoid if possible the proximity of other conductors which may create noise Tips for Making Precise Measurements e When using a current probe with a meter it is important to select the range that provides the best resolution Failure to do this may result in measurement errors e Make sure that probe jaw mating surfaces are free of dust and contamination Contaminants cause air gaps between the jaws increasing the phase shift between primary and secondary It is very critical for power measurement MAINTENANCE Warning e For maintenance use only original replacement parts e To
6. g Temperature 14 to 122 F 10 to 50 C Storage Temperature 4 to 158 F 20 to 70 C Influence of Temperature lt 0 1 per 10 Influence of Humidity From 10 to 90 0 1 Jaw Opening 2 25 57mm max Maximum Conductor Size 2 05 52mm Envelope Protection IP 40 IEC 529 Drop Test 1m IEC 68 2 32 Mechanical Shock 100g IEC 68 2 27 Vibration 5 to 15Hz 0 15mm IEC 68 2 6 15 to 25Hz 1mm 25 to 55Hz 0 25mm Polycarbonate Material Handles ABS Grey and Lexan 500R Red UL94V0 Jaws Lexan 500R Red UL94V0 Dimensions 4 37 x 8 50 x 1 77 111 x 216 x 45mm Weight 1 21lbs 550g Output SR601 Two standard safety banana jacks 4mm SR604 5ft 1 5m lead with safety 4mm banana plug SAFETY SPECIFICATIONS ceo WW E192383 Electrical Double insulation or reinforced insulation between the primary or secondary and the outer case of the handle conforms to IEC 1010 2 032 Common Mode Voltage 600V Category III Pollution Degree 2 Dielectric Strength 5550V 50 60Hz between primary secondary and the outer case of the handle Electromagnetic Compatibility EN 50081 1 Class B EN 50082 2 Electrostatic discharge IEC 1000 4 2 Radiated field IEC 1000 4 3 Fast transients IEC 1000 4 4 Magnetic field at 50 60Hz IEC 1000 4 8 ORDERING INFORMATION AC Current Probe SR601 Cat 2113 43 AC Current Probe SR604 0 Cat 2113 44 Accessories L
7. mbol signifies that the current probe is protected by double or reinforced insulation Use only factory specified replacement parts when servicing the instrument A This symbol signifies CAUTION and requests that the user refer to the user manual before using the instrument This is a type A current sensor This symbol signifies that application around and removal from HAZARDOUS LIVE conductors is permitted DEFINITION OF MEASUREMENT CATEGORIES CAT I For measurements on circuits not directly connected to the AC supply wall outlet such as protected secondaries signal level and limited energy circuits CAT Il For measurements performed on circuits directly connected to the electrical distribution system Examples are measurements on household appliances or portable tools CAT Ill For measurements performed in the building installation at the distribution level such as on hardwired equipment in fixed installation and circuit breakers CAT IV For measurements performed at the primary electrical supply lt 1000V such as on primary overcurrent protection devices ripple control units or meters RECEIVING YOUR SHIPMENT Upon receiving your shipment make sure that the contents are consistent with the packing list Notify your distributor of any missing items If the equipment appears to be damaged file a claim immediately with the carrier and notify your distributor at once giving a detailed description of any damage GJ AEMG INST
Download Pdf Manuals
Related Search