Wireless Audio Transmitter for PC
Contents
1. Model No Serial No NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference r2. is displayed although sound will be output from the S AIR sub unit you cannot perform playback operations from the S AIR sub unit You cannot use this mode when you boot iTunes or Windows Media Player on your computer until the AIR PC10T and S AIR sub unit are connected e When B play on the S AIR Sub unit is pressed and iTunes is selected iTunes window is displayed on your computer but if Windows Media Player is selected Windows Media Player window is not displayed e If you operate iTunes on your computer you may not be able to operate it on the S AIR sub unit In this case exit and restart iTunes Tips Playback operation on the S AIR sub unit may differ depending on your S AIR sub unit e Playing status contents information this unit s name AIR PC10T etc are displayed on the S AIR sub unit s front panel display Displayed items are different depending on the S AIR sub unit e If you register a Podcast or radio station on the playlist you can choose it from the S AIR sub unit e For details on the operations of the S AIR sub unit refer to the S AIR Cast Installation Instructions Advanced Remote Mode With S AIR Cast installed you can gather music files on your computer generate original channels control the contents via the S AIR sub unit without hearing system sounds output from the S AIR sub unit So you can enjoy music uninterrupted and choose your favorite song from the S AIR sub unit easily 1 Instal
3. a computer at the same time e You can use up to 10 S AIR sub units with the AIR PC10T e Only one playable source can be output from the S AIR sub unit at the same time Media Player To use Remote Mode or Advanced Remote Mode media player needs to be installed on your computer The following media players are compliant with S AIR Cast e Apple iTunes 8 0 Remote Mode Advanced Remote Mode Windows Media Player 10 11 Remote Mode Advanced Remote Mode Media Manager 1 2 Advanced Remote Mode SonicStage 4 3 Advanced Remote Mode Format The music file format that is compliant with S AIR Cast is as follows MP3 mp3 e ATRAC oma e ATRAC DRM oma e AAC m4a e AAC DRM m4p m4a e WMA wma e WMA DRM wma e WAV wav You cannot play back this format in Remote Mode You cannot play back this format in Advanced Remote Mode Notes Playback of Remote Mode is dependant on the controlled media player format e Playback of Advanced Remote Mode conforms to the player s specifications that are installed on your computer To use WMA format in Advanced Remote Mode Windows Media Player needs to be installed on your computer e Note that playback of the above music file formats may not be possible in some cases Installing S AIR Cast Installation may take some time depending on the environment A progress bar is displayed while installation is underway Wait until the installa
4. the wireless audio transmitter Indicator Lights up Status Off Connection with S AIR sub unit not available S AIR Amber Waiting for connection with S AIR sub unit Green Connected with one or more S AIR sub unit Off Pairing is off Only S AIR ID setting is made PAIRING Yellow flash Pairing is in progress Yellow Pairing is on Connecting the system 1 Connect the cradle to your computer 2 Plug wireless audio transmitter to the cradle Before connecting detach the USB cap from the wireless audio transmitter Sai o PAIRING o a Larn Nm ZZ LESZ LIZI e aa n a AA E A A a na OLE L LIL IT Z gt Tip You can connect the wireless transmitter directly to your computer without using the cradle but as this connection may be easily affected by the environment we recommend using the wireless transmitter with a cradle When the connection finishes you can then listen to music contents on the connected computer from the S AIR sub unit To listen to music check the following Connect an S AIR Sub unit Set the S AIR ID of the connected S AIR sub unit to A e Set the sound playback device property on your computer to AIR PC10T To select the sound playback device property click in the following sequence Windows Vista in Classic View Start Control Panel Sound Playback Windows XP in Classic View Start Control Pan
5. 4 134 954 11 3 SONY Wireless Audio Transmitter for PC Operating Instructions AIR PC10T S A R AMAN A DIGITAL WIRELESS 349541 3 2009 Sony Corporation Printed in China http www sony net The available scientific evidence does not show that any health problems are associated with using low power wireless devices There is no proof however that these low power wireless devices are absolutely safe Low power wireless devices emit low levels of radio frequency energy RF in the microwave range while being used Whereas high levels of RF can produce health effects by heating tissue exposure to low level RF that does not produce heating effects causes no known adverse health effects Many studies of low level RF exposures have not found any biological effects Some studies have suggested that some biological effects might occur but such findings have not been confirmed by additional research This equipment has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency RF Exposure Guidelines in Supplement C to OET65 This equipment must not be co located or operated in conjunction with any other antenna or transmitter Owner s Record The model and serial numbers are located on the rear of the unit AIR PC10T Record these numbers in the space provided below Refer to them whenever you call upon your Sony dealer regarding this product
6. If the issue persists after RF setting change the S AIR ID of the AIR PC10T and S AIR sub unit For details on RF change refer to S AIR Cast Help gt The S AIR sub unit is connected to another S AIR main unit Change the S AIR ID of the S AIR sub unit to another one and set the AIR PC10T s ID to the same one as the S AIR sub unit or pair the AIR PC10T with the S AIR sub unit you are using gt Check that the AIR PCIOT is not connected to anything other than the computer on which you performed the S AIR Cast settings gt Select Remote Mode or Advanced Remote Mode When the S AIR Cast is installed on your computer you can set S AIR settings although Standard Mode is selected gt The connected S AIR sub unit is turned off Make sure the power cord is connected then turn on the S AIR sub unit gt If you use another S AIR main unit place it more than 8 m 26 4 feet away from the AIR PCIOT S AIR settings S AIR ID Pairing RF CHANGE are not available gt To perform the S AIR settings the supplied software S AIR Cast is required Install S AIR Cast and change S AIR Cast settings For details refer to Changing Settings in the S AIR Cast Installation Instructions gt When S AIR connection settings are stored on your computer S AIR Advanced settings you cannot change S AIR ID Pairing and RF change settings In this case clear them from your computer For details refer to Changing Settings in t
7. If you cannot improve S AIR reception change the RF change setting For details refer to the operating instructions of each S AIR product
8. acteristic of radio waves and is not malfunction e As the S AIR function transmits sound by radio waves equipment that generates electromagnetic energy such as a microwave oven may interfere with sound transmission e As the S AIR function uses the radio waves that share the same frequency as other wireless systems such as wireless LAN or Bluetooth interference or poor transmission may result In this case take the following steps Do not install the system near other wireless systems Do not use the system and the other wireless systems at the same time e The transmission distance differs depending on the usage environment Find a location where transmission between the AIR PC10T and the S AIR sub unit is most effective and install the AIR PC10T and the S AIR sub unit there Troubleshooting 1 Make sure the power of your computer and S AIR sub unit is on 2 Find your problem in the checklist below and take the indicated corrective action If the issue persists contact your nearest Sony dealer When bringing the AIR PC1O0T in for repairs be sure to bring in the entire system Wireless audio transmitter cradle and the S AIR sub unit This product is a system product and the entire system is needed to determine the location requiring repair Your computer does not recognize the AIR PC10T asa USB device gt Disconnect and reconnect the AIR PC1OT The S AIR indicator does not light when connectin
9. ad Manual S AIR Cast Installation Instructions is displayed 5 Installation starts If you click Cancel installation is canceled IE 5 AIR Cast Setup Installing OpenMG SDKS 2 Installing Cancel 6 After the installation is completed click Restart Now to restart your computer E S AIR Cast Setup a Restart Nov Cancel After restarting your computer the S AIR Cast Configuration wizard appears automatically For details refer to Setting S AIR Cast in the Installation Instructions To uninstall S AIR Cast If you want to remove the S AIR Cast from your computer follow the uninstall procedure described below 1 Close S AIR Cast on the task tray Right click the task tray icon then click Exit The task tray icon disappears N Uninstall S AIR Cast in the following sequence Windows Vista in Classic View Click Start Control Panel Programs and Features in that order Windows XP in Classic View Click Start Control Panel Add or Remove Programs in that order w Select S AIR Cast and click Uninstall Windows Vista or Change Remove Windows XP Note For Windows Vista the User Account Control UAC window appears Click Allow If you click Cancel you will not be able to uninstall 4 Restart the computer e As the S AIR function transmits sound by radio waves sound may skip when radio waves are obstructed This is a char
10. ck on your computer gt Do not place a mobile phone near the AIR PC10T or the S AIR sub unit as this may result in noise The S AIR indicator on the AIR PC10T lights up in amber gt No S AIR sub unit is connected to the AIR PC10T When one or more S AIR sub units are connected the indicator lights up in green The PAIRING indicator on the AIR PC10T lights up in yellow gt The AIR PC10T is pairing with an S AIR sub unit If pairing is canceled the indicator turns off Buttons on the S AIR sub unit are not functional gt S AIR Cast does not boot or Standard Mode is selected Boot S AIR Cast then select Remote Mode or Advanced Remote Mode gt If you use electronic equipment of 2 4 GHz frequency wireless LAN Bluetooth etc turn off this equipment or place it as far as possible from the AIR PC1OT gt Set RF change to OFF on the installed S AIR Cast software If the issue persists after RF setting change the S AIR ID of the AIR PC10T and S AIR sub unit For details on RF change refer to S AIR Cast Help The Bluetooth mouse does not move during S AIR connection gt Connect the AIR PC10T to your computer using a cradle gt Place the mouse and the AIR PC1OT as far apart as possible Output 40 mW Frequency band 2 4000 GHz 2 4835 GHz Modulation method DSSS Power requirements DC 5 0 V 500 mA Dimensions w h d 26 x 13 2 x 87 mm 1 1 32 x 1 2 x 3 7 16 in Mass 21 5 g 0 758 oz Supplied accesso
11. eceived including interference that may cause undesired operation When you use the AIR PC10T connected to a notebook PC with the wireless function wireless LAN etc switch off the wireless function or place the AIR PC10T with supplied cradle attached more than 20cm 7 s feet away from your computer S AIR and its logo are trademarks of Sony Corporation S AIR Cast is a trademark of Sony Corporation SonicStage is a trademark of Sony Corporation Microsoft Windows Windows Vista and Windows Media are trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries e iTunes is a registered trademark of Apple Inc Apple Macintosh and Mac OS are trademarks of Apple Inc registered in the U S and other countries e All other trademarks and registered trademarks are of their respective holders In this manual TM and marks are not specified About the S AIR AIR PCI10T is compatible with the Sony s S AIR products which allows transmission of sound between S AIR products wirelessly S AIR Sony Audio Interactive Radio frequency Recent times have seen the rapid spread of DVD media Digital Broadcasting and other high quality media To ensure that the subtle nuances of these high quality media are transmitted with no deterioration Sony has developed a technology called S AIR for the radio transmission of digital audio signals with no compression and has
12. el Sound and Audio Devices Audio e At this time you cannot perform playback operation on the S AIR sub unit To control the playback operation on the S AIR sub unit install S AIR Cast For details see Installing S AIR Cast software For details on S AIR sub unit connection refer to the operating instructions supplied with the S AIR sub unit Installing S AIR Cast software To operate contents of your computer using S AIR sub unit you must first install the supplied S AIR Cast software on your computer For details on the setting and operation refer to the S AIR Cast Installation Instructions contained on the supplied CD ROM What is S AIR Cast With S AIR Cast installed you can control the media player on your computer using buttons on the S AIR sub unit speaker music receiver etc You can also compile or manage the contents on your computer and change the settings of the AIR PC1OT S AIR Cast can be switched to the following 3 modes Standard Mode Remote Mode and Advanced Remote Mode To use Remote Mode and Advanced Remote Mode S AIR Cast needs to be installed on your computer When you use the AIR PC10T in Standard Mode you do not need to install S AIR Cast but you need to install S AIR Cast when you change S AIR connection settings S AIR ID setting pairing etc Mode Playback S AIR Cast Sound from sub Operation on method installation unit the sub unit System sound
13. erform a pairing operation install S AIR Cast on your computer e If AIR PC10T cannot connect to the S AIR sub unit change the S AIR ID To change the S AIR ID install S AIR Cast on your computer Remote Mode You can connect an S AIR sub unit wirelessly to your computer as a speaker and listen to music contents registered in iTunes or Windows Media Player by operating the S AIR sub unit Note that all system sounds of your computer incoming message alerts alarm beeps etc will also be output from the S AIR sub unit To use this mode S AIR Cast needs to be installed on your computer 1 Install S AIR Cast on your computer 2 Perform the S AIR Cast settings on your computer in accordance with the S AIR Cast Configuration wizard Select Remote Mode and specify the media player to playback iTunes or Windows Media Player Connect AIR PC10T to your computer Set the AIR PC10T and S AIR sub unit to the same S AIR ID When the S AIR connection between AIR PC1OT and the S AIR sub unit is established PC appears on the S AIR sub unit s front panel display 3 Press B play on the S AIR sub unit AIR PCI10T and S AIR sub unit are connected Playback starts and the playback sound is output from the S AIR sub unit Notes When PC is displayed on the S AIR sub unit s display make the Remote Mode connection between AIR PC10T and the S AIR sub unit by pressing B play or S AIR CH button s When PC
14. g the AIR PC10T and the S AIR sub unit gt Check that the power of your computer is on gt Check if your computer is in sleep mode and if so exit sleep mode gt Connect the unit directly to the USB port of your computer without using a hub gt If you use electronic equipment of 2 4 GHz frequency wireless LAN Bluetooth etc turn off this equipment or place it as far as possible from the AIR PCIOT gt Set RF change to OFF on the installed S AIR Cast software If the issue persists after RF setting change the S AIR ID of the AIR PC10T and S AIR sub unit For details on RF change refer to S AIR Cast Help gt If another S AIR main unit such as Sony s wireless home theater system using S AIR is placed near the AIR PC1OT turn off the power of that S AIR main unit or place it as far as possible from the AIR PC10T gt Check that the USB cable of the cradle is connected securely to the USB port of your computer gt If the issue persists the AIR PC10T may be at fault Contact your nearest Sony dealer Connecting the AIR PC10T and the S AIR sub unit is not possible gt Confirm the S AIR IDs of the AIR PC10T and the S AIR sub unit gt Cancel pairing once then try to pair again gt If you use electronic equipment of 2 4 GHz frequency wireless LAN Bluetooth etc turn off this equipment or place it as far as possible from the AIR PC1OT gt Set RF change to OFF on the installed S AIR Cast software
15. he S AIR Cast Installation Instructions There is noise no sound or the sound skips gt Select the sound playback device property on your computer to AIR PC10T Standard Mode Remote Mode or anything except AIR PC10T Advanced Remote Mode Click in the following sequence Windows Vista in Classic View Start Control Panel Sound Playback Windows XP in Classic View Start Control Panel Sound and Audio Device Audio gt If you use electronic equipment of 2 4 GHz frequency wireless LAN Bluetooth etc turn off this equipment or place it as far as possible from the AIR PC1OT gt Set RF change to OFF on the installed S AIR Cast software If the issue persists after RF setting change the S AIR ID of the AIR PC10T and S AIR sub unit For details on RF change refer to S AIR Cast Help gt Adjust the volume of your computer gt If you use another S AIR main unit place it more than 8 m 26 s feet away from the AIR PC1OT gt Place the AIR PC10T and the S AIR sub unit closer together gt Stop using any equipment that generates electromagnetic waves such as a microwave oven gt When in Remote Mode remove the unplayable contents from media players iTunes or Windows Media Player you are using then close the media player and restart gt Turn off your computer and S AIR sub unit and then turn them on again gt Check that headphones are not connected to the headphone ja
16. incorporated this technology into the AIR PC10T This technology transfers digital audio signals with no compression using the 2 4 GHz band range of ISM band Industrial Scientific and Medical band such as wireless LANs and Bluetooth applications About S AIR products There are two types of S AIR product e S AIR main unit this unit This is for transmitting sound e S AIR sub unit This is for receiving sound speaker music receiver etc By connecting the AIR PC1OT to a USB port of your computer the AIR PCI10T can transmit music stored on your computer to an S AIR sub unit for playback Furthermore if you install the supplied application software S AIR Cast on your computer and select Remote Mode or Advanced Remote Mode you can also control the contents on an S AIR sub unit For example you can install S AIR sub units one in the study room and the other in the bedroom and then install your computer with the AIR PC10T connected in the living room You can then listen to music from the computer by controlling the S AIR sub unit EEJ ERE 4 A ry cay S AIR sub unit S AIR sub unit music receiver etc speaker etc le Supplied CD ROM AIR PC10T Computer Establishing sound transmission between the AIR PC10T and the S AIR sub unit ID setting Simply by matching the ID of the AIR PC10T and the S AIR sub unit you can establish sound transmission Identifying the AIR PC10T with a
17. l S AIR Cast on your computer 2 Perform the S AIR Cast settings on your computer in accordance with the S AIR Cast Configuration wizard Select Advanced Remote Mode and perform the Advanced Remote Mode settings Connect AIR PC10T to your computer Set the AIR PC10T and S AIR sub unit to the same S AIR ID When the S AIR connection between AIR PC1OT and the S AIR sub unit is established content s title is displayed on the S AIR sub unit s front panel display 3 Press DISPLAY on the S AIR sub unit to select the desired channel group 4 Press B play on the S AIR sub unit Playback starts 5 Press S AIR CH on the S AIR sub unit to select the channel you want to playback For example when an album name is displayed on the S AIR sub unit s front display you can change to a different album by pressing S AIR CH Tips Playback operation on the S AIR sub unit may differ depending on your S AIR sub unit e Playing status contents information this unit s name AIR PC10T etc are displayed on the S AIR sub unit s front panel display Displayed items are different depending on the S AIR sub unit For details on the operations of the S AIR sub unit refer to the S AIR Cast Installation Instructions SSS System Requirements The following software and hardware are required to run S AIR Cast Notes e S AIR Cast will not run in any Mac OS e English is the only language available for S AIR Cast The fol
18. lowing systems are not supported Any 64 bit operating system Personally assembled PCs or operating systems Operations are not guaranteed for all the recommended computer environments mentioned below Operating systems e Windows Vista Home Basic SP1 or without SP e Windows Vista Home Premium SP1 or without SP e Windows Vista Ultimate SP1 or without SP Windows Vista Business SP1 or without SP e Windows XP Home Edition SP2 SP3 e Windows XP Professional SP2 SP3 e Windows XP Media Center Edition 2004 SP2 SP3 e Windows XP Media Center Edition 2005 SP2 SP3 Hardware environments e CPU Pentium 1GHz or higher Celeron 1 GHz or higher or better equipment CPU e RAM 512 MB or more In the case of high music content operating speed may decrease For smooth operation 2GHz or higher CPU is recommended Hard Disk Drive 206MB or more S AIR Cast related module 60MB Microsoft related module 146MB e CD ROM or DVD drive for software installation Display Screen Resolution 1 024 x 768 pixels or higher Colors 65 536 colors or higher Mouse Keyboard USB port USB 1 1 or 2 0 port Sound card Software Internet Explore 6 0 or higher User privileges e S AIR Cast can be used only by users with administrator privileges e S AIR Cast does not support the Fast User Switching function e You can connect one AIR PC10T to a computer You cannot connect multiple AIR PC10T to
19. ns e Other factors The following may cause poor reception Materials or structures such as walls and floors The location where an S AIR product is placed When you use the AIR PC10T connected to a notebook PC with the wireless function wireless LAN etc switch off the wireless function or place the AIR PC10T with supplied cradle attached more than 20cm 7 7 s feet away from your computer When using S AIR sub units place them as far as possible from the above electronic equipment or place where S AIR reception is stable When S AIR reception is poor Check the following Keep cords that are connected to the S AIR product power supply cord power cord antennas or other cords away from the wireless transceiver and slot Keep as much space as possible around S AIR products Avoid placing S AIR products on top of or directly below other electronic equipment Avoid placing S AIR products in a closed rack metal rack or under a table Adjust the location height orientation and place in the room of S AIR products until reception is the most stable Place so that the AIR PC10T and the S AIR sub unit are closer Boome gt lt 4 Place so that S AIR products are separated from other wireless devices D LEI 4 Place so that S AIR products are separated from metal doors or tables
20. of Application for Not your computer Ti playback music required will be output as Not available well F System sound of iTunes pr our computer Remote Windows Required G b P Available Media Player wide output as well Dedicated aevanced module plays at Required Payback musi Available background y For details on S AIR Cast operation refer to the S AIR Cast Help For details on S AIR sub unit operation refer to the operating instructions supplied with the S AIR sub unit Overview of each mode procedure Standard Mode This mode is for using an S AIR sub unit as a PC speaker By connecting AIR PC10T to your computer computer sound is output from the S AIR sub unit Note that all system sounds of your computer incoming message alerts alarm beeps etc will also be output from the S AIR sub unit In this mode you can use this system without installing S AIR Cast but installation is necessary if you want to change the S AIR connection settings 1 Connect AIR PC10T to your computer 2 Turn on the S AIR sub unit and then set the AIR PC10T and S AIR sub unit to the same S AIR ID 3 Start playing music on the media player of your computer Notes e In this mode you cannot perform playback operation from the S AIR sub unit e PC is displayed on the S AIR sub unit s front panel display The connecting S AIR main unit s name AIR PC10T may be displayed depending on your S AIR sub unit Tips e If you want to p
21. ries e Cradle AIR PCST1 1 USB cap 1 e Application software S AIR Cast CD ROM 1 Operating Instructions 1 Design and specifications are subject to change without notice To stabilize S AIR reception To use S AIR products AIR PC10T and the S AIR sub unit Before using S AIR products have the following ready e Confirm the wireless transceiver on the S AIR sub unit if applicable is inserted correctly Insert the wireless transceiver firmly to the depth into the slot of the S AIR sub unit if applicable Insert firmly Confirm that the S AIR IDs of the AIR PC10T and the S AIR sub unit are the same The default setting of the S AIR IDs of the AIR PC1OT and the S AIR sub unit is A You can set the S AIR ID using the supplied S AIR Cast software There are several ways to set the S AIR ID of the S AIR sub unit using the S AIR ID switch setup menu etc For details refer to the operating instructions of each S AIR product Same S AIR ID About environments where S AIR products AIR PC10T and the S AIR sub unit are used S AIR products use a radio frequency of 2 4 GHz Certain electronic equipment or other factors may cause lost connection or instability in S AIR reception Electronic equipment influence The following may cause interference or cross talk Cellular phones cordless phones Wireless LAN personal computers Game machines using radio signals Microwave ove
22. specific S AIR sub unit Pairing operation It is easy to set the same ID for the AIR PC10T and the S AIR sub unit to establish sound transmission However neighbors may also receive your system s sound if IDs are the same or you may receive sound from your neighbors To prevent this you can identify the AIR PC10T with a specific S AIR sub unit by performing the pairing operation To perform the pairing operation you need to install the supplied S AIR Cast software For details refer to the S AIR Cast installation instructions About AIR PC10T manual AIR PCI10T contains the following manuals Refer to them as required by the operation Window screen illustrations depicted in the manuals below may differ from the actual screens AIR PC10T Operating Instructions this manual This manual explains the operations of the AIR PC10T S AIR Cast Installation Instructions This PDF manual which is copied to your computer when the S AIR Cast software is installed explains how to install and set up the supplied S AIR Cast software on your computer S AIR Cast Help This help manual can be used only after the S AIR Cast software is installed It explains the operations of the S AIR Cast software included on the same CD ROM Wireless audio transmitter AIR PC10T S AIR indicator PAIRING indicator USB cap Cradle USB plug Note This cradle is for the AIR PC10T Do not use it for other USB devices About indicators on
23. tion is finished To confirm the installation procedure and the S AIR Cast settings select View Manual in Step 4 1 Turn on your computer and log in as an administrator Wait for Windows to load 2 Insert the supplied CD ROM into the CD ROM drive of your computer Windows Vista users only The Auto Play window appears Click Run setup exe to install the program E AutoPlay fo a Windows Vista users only The User Account Control UAC window appears Click Continue If you click Cancel you will not be able to start the installation User Account Control ry Sony Corporation V Details Continue Cancel User Account Control helps stop unauthorized changes to your computer The S AIR Cast Setup wizard appears Exit all applications and click Next IE 5 AIR Cast Setup Next Cancel Note If the wizard does not open double click the CD ROM Setup exe icon 3 Read the license agreement Check I have read and accept the license terms and click Next WP SAR Cansa Tip If you do not accept the license agreement check I do not accept the license terms and click Cancel The wizard will turn off 4 Click Install S AIR Cast first then click Install Now A EAR Ga Saup Install Now Tip If you click About S AIR Cast then click Read Document the details of the product are displayed If you click View Manual then click Re
Download Pdf Manuals
Related Search