Home

7.3 Software Release Notice

1. 16 MIB Download Steps for Third Party SNMP Managers This section lists Vanguard MIB files needed for SNMP management of Vanguard devices when using aa third party non Vanguard Networks SNMP Network Management System NMS 16 1 Obtaining MIB Files Vanguard MIB files for your third party NMS are available from the Vanguide 7 3 RO0A CD ROM You can also download MIB files from the internet The address for the server is http www vanguardnetworks com support downloads mibs htm On the internet there is one ZIP file for the PC and one ZIP file for UNIX You must unzip the ZIP file to get the MIB files The contents of these two ZIP files are identical However the formats of the files in these two ZIP files are slightly different due to the way PCs and UNIX systems handle text files Depending on the protocols and options provided by the Applications Ware image installed in your node you might not need all the MIB files See the Required Files and Loading section below for details on the files you should have to support SNMP management for Vanguard products 16 2 Required Files and Loading The following MIB files are required by your NMS to perform SNMP management of Vanguard products e rfc1213 mib e cdx_6500 mib These files must be loaded first and in the order shown After you load these required files onto your NMS you can load the MIB files for the options and protocols installed on your Vanguard hardw
2. Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Type of Service in the Internet Protocol Suite P Almquist Jul 01 1992 Multiprotocol Interconnect On X 25 And ISDN In The Packet Mode A Malis D Robinson R Ullmann August 1992 Novell IPX over Various WAN Media IPXWAN M Allen Sept 01 1992 Definitions Of Managed Objects For The Ethernet like Interface Types F Kastenholz January 1993 Multiprotocol Encapsulation over ATM Adaptation Layer 5 Juha Heinanen July 1993 See RFC 2684 RFC 2684 obsoletes RFC 1483 Multiprotocol Interconnect Over Frame Relay T Bradley C Brown amp A Malis July 1993 Applicability Statement For The Implementation Of Classless Inter Domain Routing CIDR Internet Engineering Steering Group R Hinden September 1993 An Architecture For IP Address Allocation With CIDR Y Rekhter amp T Li September 1993 Classless Inter Domain Routing CIDR an Address Assignment and Aggregation Strategy V Fuller T Li J Yu amp K Varadhan September 1993 Exchanging Routing Information Across Provider Boundaries in the CIDR Environment Y Rekhter amp C Topolcic September 1993 Interoperation between DHCP and BOOTP R Droms Oct 01 1993 Clarifications and Extensions for the Bootstrap Protocol W Wimer Oct 01 1993 TN3270 Current Practices J Penner DCA Inc January 19
3. 3460 80 Voice Routing Services only gt gt lt lt 3460 80 Half Duplex Radio only G 723 1 G729A G711 can t lt lt 3460 80 add T 38 only G 723 1 G711 can add T 38 Sen G 729AB G711 can add lt lt 3460 80 T 38 only G 723 1 G729A G71 1 T 38 lt lt 3460 80 but no VAD only lt lt 3460 80 only Centralized Voice Switching 3460 80 Voice Routing Services only gt gt lt lt 3460 80 FAX ITU T 38 only Vanguard T1 E1 PRI Digital Voice Server lt lt 3460 80 Half Duplex Radio only T 38 w G 723 amp G 711 for T1 E1 T 38 w G 729a amp G 711 for T1 E1 Voice Relay with G 723 1 and G 729a Voice Relay Encapsulated in IP SoTCP H 323 v 2 Standards Based Voice lt lt 3460 80 H 323 H 323 Caller ID L only VOICE IP ENCAPSULATION 3460 80 only gt gt 3460 80 only gt gt 3460 80 only gt gt 3460 80 only gt gt 3460 80 only gt gt 3460 80 only gt gt SIP SIP Connect 1 0 Caller ID Call Hold Call Waiting Call Transfer Call Forward Proprietary Page 57 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 3460 80 3rd Party Conferencing only gt gt LAN Router IP D i LAN Option Protocols LLC Eth IPXWAN Appletalk Bandwidth on Demand Ld Bal Router Proxy Router Discovery Network A
4. Number of Voice SVC per Annex G station Number of DLCIs per node Session Number of LCON Number of Virtual Ports FR X25 PPP Voice Max Number of Multi link PPP profiles Max Number of MLPPP switched links per MLPPP Profile 30 Number of UDP SoTCP sessions terminating in the node 188 Proprietary Page 35 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Number of TCP SoTCP sessions terminating in the node Number of simultaneous calls per node Network Services Number of Network Services Tables Entries Number of PVCs table entries Number of mnemonic table entries Number of Switch Service table entries Number of X25 routing table entries LAN IP Specific Routing table size Routing Cache Accelerated Aggregated Route cache Number of LCONs Number of Interfaces Access Control List table size Policy based routing table size Static ARP table Number of static routes MAC Filter Table Entries RIP Route Control table NAT table size IP Multicast DVMRP Tables size Maximum number of Multicast Interfaces supported CIDR RIP aggregate table CIDR Multi home table size Proprietary Page 36 of 84 8 11 2010 Vanguard Networks Applications Ware Software
5. 1 10 T10BP111 5 4 PO8 The pound sign represents a letter from C to Z 1 11 T10BP130 5 4 POLA 5 4 POKA and 5 4 POJA Boot prom version 1 30 is required to run the 5 4 Point Release L software The 1 30 version of the boot prom does not work with any earlier 5 4 P08 software If you have a new CPU card use boot prom 1 40 or 1 50 The asterisk represents a letter from A to Z 1 30 or greater T10BP140 5 4 POLB Boot prom version 1 40 or greater is required to run with the new CPU cards 1 40 or greater T10BP150 6 0 R00A 6 1 R000 6 2 R000 6 3 ROOA 6 4 ROOA 6 4 R10A T10BP151 Proprietary 6 0 R00A 6 1 R000 6 2 R000 6 3 ROOA 6 4 ROOA 6 4 R10A Page 43 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Boot prom 1 51 is the latest for the MCP750 CPU Do not use boot prom 2 00 on the MCP750 CPU T20BP200 6 4 ROOA and 6 4 RI0A The IBM750 CPU must use boot prom 2 00 T30BP300 6 5 ROO00 or greater Boot prom revision 3 00 supports IBM750 and MPC750 CPUs Boot prom revision 3 00 is mandatory for Release 6 5 R000 Note The respective xrc file is contained in the directory with the same name Example T10BP140 xrc would be found in the T10BP140 directory T10BP150 xrc would be found in the T10BP150 directory 8 5 Directory Example The figure below sho
6. Range Enabled Disabled Default Disabled This parameter controls the discarding of TCP packets having no flags set in the TCP packet header This is an illegal TCP flags value When protection is enabled a count is maintained to track the number of times each DoS attack occurs Once per second an alarm is logged for each counter having a non zero value Upon logging the alarm the counter is cleared The following is an example of a DoS alarm 2 900 07 SEP 2003 01 07 11 DOS_Type Timestamp IP Options Zone Trust Src 150 30 74 38 Dest 172 16 1 57 Proto 1 Count 1 5 Software Improvements This section describes specific improvements to the Applications Ware software It includes e Customer initiated Change Requests e New features to address new applications These Change Requests were reported to Customer Service and interim patch releases were released to fix the problems These Change Requests are incorporated into Release 7 3 RO0A and where applicable interim patch releases have been replaced by Release 7 3 RO0A Proprietary Page 26 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Interim Patch Release GEN Replaced by Release 7 3 RO0A 16670 6 5 P03E FXO ports are getting hung and a node boot is required to clear 17376 70T16F TCP header compression not working 17509 7 2 P03A Need to implement more QoS IP CL Tc Mapper profile entries 17561 7 1 T13A 3 party conf
7. Range Enabled Disabled Default Disabled This parameter controls the discarding of fragmented IP packets If enabled a packet is discarded if the More Fragments flag is set or the Fragment Offset field in the IP header is nonzero 1 SYN Fragment Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of fragmented TCP SYN packets If enabled a packet is discarded if the SYN flag is set and the More Fragments flag is set or the Fragment Offset field in the IP header is nonzero 1 ICMP Fragment Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of fragmented ICMP packets If enabled a packet is discarded if the protocol is ICMP and the More Fragments flag is set or the Fragment Offset field in the IP header is nonzero 1 Large ICMP Packet Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of large ICMP packets If enabled a packet is discarded if the protocol is ICMP and the total packet length field in the IP header is greater than 1024 bytes 1 Bad IP Options Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of IP packets having an invalid IP options field in the IP packet header Proprietary Page 24 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 R
8. Disabled This parameter controls the discarding of oversized ICMP packets If enabled a packet is discarded if the total packet size is greater than 65 535 bytes even if the packet is fragmented Proprietary Page 25 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 1 WinNuke Attack Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of TCP packets having a destination port of 139 and the Urgent flag set in the TCP header This introduces a NetBIOS fragment overlap causing many Windows machines to crash 1 Land Attack Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of TCP packets having the SYN bit set with both the source and destination IP addresses the same in the IP packet header 1 SYN and FIN Flags Set Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of TCP packets having both the SYN and FIN flags set in the TCP packet header This is an illegal TCP flags combination 1 FIN Flag Without ACK Flag Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of TCP packets having the FIN flag set without the ACK flag set in the TCP packet header This is an illegal TCP flags combination 1 TCP Packet Without Flags Set Protection Disabled
9. European Bundle E1 ETSI Asia Bundle T1 NTT Switch Variants None Required Switch Types User Side Only N A Bundle T1 NI 1 4ESS SESS DMS 100 European Bundle E1 ETSI Asia Bundle T1 NTT Switch Variants None Required Voice Signaling Support CAS E amp M Wink Delay Immediate Colisee and Seizure Ack 3460 3480 FXS Loopstart 3460 3480 FXO Loopstart 3460 3480 CAS E amp M Wink Delay Immediate Colisee and Seizure Ack FXS Loopstart FXO Loopstart CCS 2 3 4 e N A Bundle T1 Q Sig Master Slave 5 SESS Net work User 6 NI 1 Network User 6 DMS100 Network User 6 e Euro Bundle E1 ETSI Net work User Q Sig Master Slave 5 CAS E amp M Wink Delay Im mediate Colisee and Seizure Ack FXS Loopstart FXO Loopstart CCS 2 3 4 e N A Bundle T1 Q Sig Master Slave 5 SESS Net work User 6 NI 1 Network User 6 DMS100 Network User 6 e Euro Bundle E1 ETSI Net work User Q Sig Master Slave 5 Features Trunking Gateway 3460 3480 E1 only Timeslot Bypass Timeslot Bypass Additional Clocking Features Node Wide Network Clock Source 3460 3480 E1 only Node Wide Network Clock Source Node Wide Network Clock Management Data Applications Each Group of 4 T1 E1 ports can synchronize to a different carrier Voice amp Data Applications Each card has to be connected to one carr
10. K McCloghrie M Rose S Walbusser January 1996 Address Allocation for Private Internets Y Rekhter B Moskowitz D Karrenberg G J de Groot amp E Lear February 1996 The PPP Multilink Protocol MP K Sklower B Lloyd G McGregor D Carr T Caradetti August 1996 BGP Communities Attribute R Chandra P Traina Cisco Systems T Li August 1996 Application of the BGP Community Attribute in Multi home Routing E Chen MCI T Bates Cisco Systems August 1996 Proprietary Page 78 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Dynamic Host Configuration Protocol DHCP R Droms Bucknell University March 1997 DHCP Options and BOOTP Vendor Extensions S Alexander Silicon Graphics Inc R Droms Bucknell University March 1997 Internet Group Management Protocol IGMP Version 2 W Fenner Xerox PARC November 1997 Virtual Router Redundancy Protocol VRRP S Knight D Weaver Ascend Communications D Whipple Microsoft Inc R Hinden D Mitzel P Hunt Nokia P Higginson M Shand Digital Equipment Corp A Lindem IBM Corporation April 1998 Protocol Independent Multicast Sparse Mode PIM SM D Estrin D Farinacci A Helmy D Thaler S Deering M Handley V Jacobson C Liu P Sharma L Wei CISCO UCL USC LBL XEROX and UMICH June 1998 PPP Over AALS G
11. Part Number T0100 08 Protocol Priority Part Number T0100 09 Quality of Service Part Number T0100 10 Asynchronous Transfer Mode Part Number T0100 1 1 7300 Series T3 ATM Part Number T0100 12 Border Gateway Protocol BGP 4 Part Number T0100 13 Traffic Monitor Part Number T0100 15 Ethernet Basics Part Number T0109 Token Ring Basics Part Number T0111 Firewall DMZ Part Number T0293 Proprietary Page 52 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 10 3 Applications Ware SNA Feature Protocols Manual The SNA Feature Protocols Manual T0101 consists of these manuals BSC 2780 3780 Part Number T0101 02 BSC 3270 Part Number T0101 03 IBM 2260 Part Number T0101 04 SDLC Part Number T0101 05 XDLC Part Number T0101 06 AS 400 Communication Server Part Number T0101 07 BSC 3270 to SNA Conversion Part Number T0101 08 BSC 2780 3780 to SNA LUO Conversion Part Number T0101 09 TN3270 Remoter Server Part Number T0101 10 VBIP BSC3270 to TCP IP Conversion Part Number T0290 10 4 Applications Ware Serial Feature Protocols Manual The Serial Feature Protocols Manual T0102 consists of these manuals Burroughs Poll Select Part Number T0102 02 NCR BSC Part Number T0102 03 TBOP Part Number T0102 04 NCCP Part Number T0102 05 TCOP Part Number T0102 06 SHDLC Part Number T0102 07 T3POS Part Number T0102 08 3201 Part Number T0102 09 X 42
12. Part Number T0102 10 TNPP Part Number T0102 11 TPDU Part Number T0102 12 SPP Part Number T0102 13 AC100 Part Number T0102 14 ALC Part Number T0102 15 10 5 Applications Ware Multi Service Feature Protocols Manual The Multi Service Feature Protocols Manual T0103 consists of these manuals Internal DSD Part Number T0103 02 Multipoint X 25 Part Number T0103 03 Frame Data Compressor Part Number T0103 04 Vanguard 6560 6520 ISDN Part Number T0103 05 Vanguard ISDN Part Number T0103 06 Remote DataScope Part Number T0103 07 SMDS Part Number T0103 08 Data Encryption Part Number T0103 09 Virtual Private Network Part Number T0103 10 10 6 Applications Ware Multimedia Feature Protocols Manual The Multimedia Feature Protocols Manual Part Number T0104 consists of these manuals e Voice Technology Reference Guide Part Number T0104 04 e Vanguard Voice Manual Part Number T0104 05 e Vanguard Voice Hardware Reference Card Part Number T0104 06 10 7 Applications Ware Alarms and Reports Manual Proprietary Page 53 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 This Alarms and Reports Manual Part Number T0005 contains a listing of all alarm and report messages generated by the Vanguard Applications Ware The manual explains the actions you must perform in order to correct unexpected network situations that might arise while using any of the Applications
13. 2M CMEM Compressed MPC750 CPU 6 1 to 6 4 2M CMEM Compressed IBM750 FX CPU Invalid 1 5x boot code not working with IBM750FX CPU card Invalid 6 1 to 6 3 cold loader not working with IBM750FX CPU card 2M CMEM Compressed 2M CMEM Compressed 2M CMEM Compressed Proprietary Page 50 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO00A Part No T0300 Rev B Aug 2010 6 5 MPC750 2M CMEM to Compressed Tee Vanguard 7300 Series Platform Notes 1 The MPC750 CPU system module has 128Mbyte DRAM 2 For the MPC750 CPU system module a feature was implemented in Boot code 1 51 It enabled the node to be booted from current bank or alternate bank in the cold load menu This boot code was released with 6 3 The IBM750FX CPU system module has 512Mbyte DDR RAM For the IBM750FX CPU module boot code 2 00 should be used It has all the functionalities in 1 51 For the MPC750 CPU system module boot code 2 00 should not be used The on board flash is primarily used for boot code For Release 6 5 boot code 3 00 is mandatory Proprietary Page 51 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO00A Part No T0300 Rev B Aug 2010 10 User Documentation User documentation supporting the 7 3 RO0OA Applications Ware is organized as e Basic Protocol
14. Demand Ld Bal Router Proxy Router Discovery Network Address Transl Policy Based Routing RTP UDP IP Header Compression ETH Bridge XLB Bridge IP Tunnel GRE Proprietary Page 68 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 DHCP Server amp Client UDP Radius client Dynamic IP Address Dynamic VPN D D D IP Multicast Protocols PIM Sparse Multicast LILIL Network Protocols NHRP Registration Ly EYL OSPF BGP4 BGP IGB to BGP route Filtering BGP Multipath Load Balancing BGP Same AS as in ASPath BGP TCP MD5 Authentication VRRP FRF12 FRA only for back compatibility FRI includes FRA FR SVC DTE Interface X25 SMDS PPP Auto Dialer PPP PPP IP Header Compression PPPoE SoTCP Voice Relay Encap In IP Fractional T1 E1 Trunking Gateway for E1 only ATM Protocols ATM ATM Congestion Control IBM NETWORKING AS 400 5494 Comm Server A BSC2780 HPAD TPAD BSC2780 3780 to SNA Conversion BSC3270 HPAD TPAD VBIP BSC to IP Conversion BSC3270 to SNA Conversion IBM2260 TN3270 Rem Server Conversion LLC ETH LLC FR SDLC DID Serial Asynchronous Protocols NON IBM Proprietary Page 69 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3
15. Dos Mitigation 5 Software Improvements 6 Known Software Limitations 7 Vanguard Feature Comparison Chart 7 1 Software Configuration Limits BOOT PROM SOFTWARE UPDATES Software Loader Procomm Procedure Procomm Setup Send File Directory Example Boot Prom Information for the MPC750 Controller Card Controller Card Board Assembly Number Location Vanguard 7300 CPU Card Upgrade 9 Boot Prom and Cold loader Matrix Upgrade 10 User Documentation 10 1 Applications Ware Basic Protocols Manual 10 2 Applications Ware IP and LAN Feature Protocols Manual 10 3 Applications Ware SNA Feature Protocols Manual 10 4 Applications Ware Serial Feature Protocols Manual Proprietary Page 3 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 10 5 Applications Ware Multi Service Feature Protocols Manual 10 6 Applications Ware Multimedia Feature Protocols Manual 10 7 Applications Ware Alarms and Reports Manual 11 How to Obtain User Documentation 11 1 Download from the World Wide Web 11 2 Keep a Current Set of Manuals 12 Vanguide CD ROM with Vanguard Software Builder 12 1 Vanguard Software Builder 13 Release 7 3RO0A for the Vanguard 3410 3410W 3460 3480 14 Release 7 3RO0A for the Vanguard 6840 6841 15 Release 7 3RO0A for the Vanguard 7310 7330 16 MIB Download Steps for Third Party SNMP Managers 16 1 Obtaining MIB Files 16 2 Required Files and Loading 16 3 MIB Files for Options Protocols 17 Applications
16. Gross Lucent Technologies M Kaycee Paradyne A Lin Shasta Networks A Malis Ascend Communications J Stephens Cayman Systems July 1998 IP Payload Compression Protocol IPComp A Shacham Cisco R Monsour Hi fn Inc R Pereira TimeStep M Thomas AltaVista Internet December 1998 IP Payload Compression using LZS R Friend R Monsour Hi fn Inc December 1998 Security Architecture for the Internet Protocol S Kent BBN Corp R Atkinson Home Network November 1998 IP Authentication Header S Kent BBN Corp R Atkinson Home Network November 1998 The Use of HMAC MDS5 96 within ESP and AH C Madson Cisco System Inc R Glenn NIST November 1998 The Use of HMAC SHA 1 96 within ESP and AH C Madson Cisco System Inc R Glenn NIST November 1998 The ESP DES CBC Cipher Algorithm with Explicit IV C Madson Cisco System Inc N Doraswamy Bay Networks Inc November 1998 IP Encapsulating Security Payload ESP S Kent BBN Corp R Atkinson Home Network November 1998 Proprietary Page 79 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 The Internet IP Security Domain of Interpretation for ISAKMP D Piper Network Alchemy November 1998 Internet Security Association and Key Management Protocol ISAKMP D Maughan National Security Agency M Schertler Security
17. Inc M Schneider National Security Agency J Turner RABA Technologies Inc November 1998 The Internet Key Exchange IKE D Harkins D Carrel Cisco Systems November 1998 The NULL Encryption Algorithm and Its Use with IPSEC R Glenn NIST S Kent BBN Corp November 1998 IP Security Working Group R Thayer Sable Technology Corp N Doraswamy Bay Networks R Glenn NIST November 1998 The ESP CBC Mode Cipher Algorithms R Pereira TimeStep Corporation R Adams Cisco Systems November 1998 RIP Version 2 G Malkin Bay Networks November 1998 Definition Differentiated Services Field DS Field in IPv4 IPv6 Headers K Nichols S Blake F Baker D Black December 1998 An Architecture for Differentiated Services S Blake D Black M Carlson E Davies Z Wang W Weiss Dec 1998 Compressing IP UDP RTP Headers for Low Speed Serial Links S Casner V Jacobson Cisco Systems February 1999 The Method for Transmitting PPP over Ethernet PPPoE L Mamakos K Lidl J Evarts UNET Technologies Inc D Carrel D Simone RedBack Networks Inc R Wheeler RouterWare Incorporated February 1999 A Framework for Inter Domain Route Aggregation E Chen Cisco J Stewart Juniper February 1999 Assured Forwarding PHB Group J Heinanen F Baker W Weiss J Wroclawski June 1999 An Expedited Forwarding PHB V Jacobson K Nichols K Podur
18. Juniper SSG router is configured to accept VPNs from peers with unknown IP addresses they requires the ISAKMP Phase 1 negotiation to be in Aggressive mode and have a Peer ID to identify the remote peer Vanguard implemented Aggressive Mode with the ability to specify a Peer identifier for compatibility with the Juniper SSG family 1 ISAKMP Phase 1 Exchange Type MAIN_ MODE AGRESSIVE_MODE Range MAIN _MODE AGRESSIVE_MODE Default MAIN_MODE ISAKMP Phase 1 exchange type Main Mode More secure option generally preferred Aggressive Mode Less secure option Used with dynamic local addressing it is necessary for interoperability with some VPN concentrators 1 ISAKMP Username ID blank Range 1 63 alphanumeric characters use the space character to blank field Default blank ISAKMP ID payload identifier This parameter is required when configured for Aggressive Phase I key change mode Both U FQDN and FQDN are supported 4 7 PP IPCP Learned IP Address Line When an interface is configured as unnumbered and the PPP Profile will negotiation and accept its address from its peer the address will be installed in the router interface Note that the subnet mask used will be the one configured by the user If the router interface as a user configured IP address PPP IPCP will not install an IP address even if the address negotiated is different than the one configured by the user This feature may also be referred to as PPP IPC
19. Release R7 3RO0A Part No T0300 Rev B Aug 2010 Number of voice switching table entries Save your CMEM before configuring a large number of entries If your CMEM becomes too large the node may reset or default its configuration SNA IBM Support Number of stations per LAN interface SLAC Note Two LAN interfaces allowed per node 1 000 stations per interface Maximum number of SLAC Stations supported for BSC LU Devices Number of stations per Node SLAC Note Two LAN interfaces allowed per node 2 000 max stations per node LLC LAN Conversion Stations Vanguard 7300 Series 1 000 per interface 2 000 per node Release 6 0 and greater Vanguard 3410 3460 3480 250 per interface 500 per node Vanguard 34x 250 stations on one port LLC FRI Conversion Stations Vanguard 7300 Series 2 000 per node Release 6 1 or greater Vanguard 7300 Series 1 000 per node Prior to Release 6 1 Vanguard 34x 3410 3460 3480 250 per node Additional Limits Number of bridge links entries 7300 Series original size 250 ARP queue size 50 Max number of IPX interfaces 1 000 Number of OSPF routes 15000 G1 20000 G2 Max SVCs per SoTCP session 64 50 Max Total Data SVCs SoTCP 2 000 1 024 Max Total Voice SVCs SoTCP 2 000 1 024 IP Broadcast Forwarding Table Size 255 255 UDP Broadcast Forwarding Table Size 255 255 Outbound Translation Table Ent
20. Ware licenses on Vanguard Products The alarms and traps database is also available on the web by doing the following 1 Access the web site http www vanguardnetworks com support alarm search htm 2 Search the alarms by alarm text or SMNP trap number 11 How to Obtain User Documentation There are two ways to obtain software documentation e Download the most current up to date document files from the on line Library on our World Wide Web page e Keep a current set of documentation for Release 7 3 RO0A 11 1 Download from the World Wide Web The latest Vanguard user documentation including detailed descriptions of new features and enhancements is available on the World Wide Web Find your information faster and easier when you use the Product Documentation website Eliminate the need to flip through several documentation updates For example suppose feature enhancements are made to ISDN over the course of several software releases Each release provided a separate document describing the details of those ISDN features The details of the features are described in the ISDN Manual in context with the rest of the feature information The full set of Vanguard Documentation is available for download from the Vanguard Networks Product Documentation website http www vanguardnetworks com support documentation overview htm To read the files you need a copy of Adobe Acrobat Reader with Search This application is free from many locat
21. backward compability equivalent to Proprietary Notes T 38 Fax Requires release 6 3 or greater software and is available by purchasing a software license T 38 Fax text is not present if the T 38 Fax option is not loaded Release 6 4 and greater includes the Fax feature in the Voice Applications Ware License for the Vanguard 34x 6435 and 6455 The Vanguard 7300 includes the fax feature in the Multi Service Applications Ware T38 T38 Override or Disabled must be selected for DSP Option 4 T38 and T38 Override cannot be selected for DSP option 1 4 10 5 IP Classifier Traffic Conditioner amp QoS Mapper Profile Configuration This parameter range has been extended from its original range of 1 30 to 1 100 Entry Number 1 Range 1 100 Default 1 Entry number used to reference this table record Proprietary Page 18 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 4 11 SYSLOG Client 4 11 1 Overview The SYSLOG Client Feature is available in Release 7 3 ROOA with the installation of the Security Services License The SYSLOG Client Feature allows the Vanguard Networks Router Products to send SYSLOG messages to up to two SYSLOG servers It categorizes the SYSLOG messages into four message types Authentication Accounting Event and Traffic Monitoring and is capable of directing the SYSLOG messages to a particular Server based on the message type Figure 1 shows an exam
22. default factory image that contains a subset of the full license In some cases the default image might not completely meet your needs You can either create a new Vanguard customer image using the Software Builder application on the Vanguide CD ROM or use our Vanguard Customer Ware Program For details about all features in a particular Applications W are License refer to the appropriate section further on in this document 2 3 Software Upgrade to 7 3 RO0A Tech Tip Always save a back up of CMEM configuration memory file before upgrading This backed up CMEM file can be used to reload the configuration if you downgrade or lose the configuration Be aware that downgrading from 7 2 RO0A to any prior release is not supported and note that problems will occur with the configuration memory To properly downgrade the configuration should be defaulted and then restored with the saved CMEM that was running in the prior release DRCaa22736 2 4 License Upgrades The License Upgrades differ from standard Applications W are packages in that they do not operate in a stand alone capacity For example if you want the functions available in the SNA Applications Ware you purchase that license and load it into your unit However a License Upgrade cannot be loaded into a unit by itself You must e Purchase one of the standard Applications Ware packages e Purchase the License Upgrade e Use Software Builder to add the License Upgrade to the sta
23. from the main menu under Configuration gt Configure Router gt Configure Tunnel The new parameters added to 7 3 ROOA are e Tunnel Key e NHRP Holding Time e NHRP Network ID e NHRP Registration Timeout e NHS Address e Set NHRP Unique Flag e NHRP Authentication Here the new parameters are presented with the configurable ranges and brief description as they will appear in the Vanguard Routers Configuration menu Tunnel Key Range 0 4294967295 Default 0 Description This parameter enables the use of the optional Key field in the GRE header A value of 0 indicates the GRE Key is not used NHRP Network ID Range 0 4294967295 Default 0 Description This is an identifier for a specific NHRP network Each NHRP network must have a unique Network ID All nodes in the network must have the same Network ID A value of 0 indicates the Network ID is not used NHS Address Range A valid IP address in dotted notation Default 0 0 0 0 Description This parameter specifies the address of the Next Hop Server NHS The router will register with the NHS Proprietary Page 11 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 NHRP Authentication Range 0 8 alphanumeric characters use the space character to blank field Default blank Description This parameter specifies the authen
24. loader indicated in the current bank column of the table below Typically the c73cv115 xrc file is used Current Bank Kbps c73cvl115 xre 115 c73cv192 xre 19 2 c73cv288 xrc 28 8 c73cv384 xre 38 4 c73cv576 xre 57 6 c73cv96 xrc 96 5 Download the appropriate cold loader to your PC for the correct Boot prom version from the following directory example Proprietary Page 40 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 You must use the cold loader from the current bank column of the table in step 4 to load the Boot proms 6 When using the Procomm application e Select Send File from the Procomm Data Menu e Select RAW ASCII transfer mode e Select 9600 for the Coldloader speed The following figures show the Procomm application Note To ensure you are in RAW ASCII transfer mode in Procomm check the setup file Options gt Data Options Procomm Plus Terminal a Eile Edit view Options Data Tools Window Help Rapid Connec System Options gt e inl E Data Data Options General d ed Meta Key Editor SEAN e Keyboard Editor Alt F8 Right a Translate Table Editor Paths Answer Options Setup Files Transfer Protocol Terminal Options Terminal Fonts Terminal Colors Window Colors Alt Host Chat Logorwiz WinLink Cmd Mod Send Fax Explorer DOS Prmp RAW ASCI
25. 0A i 7 1 R00A 64k CMEM 4M image maximum 7 2 R0O0A A 7 2 R00A 64k CMEM 4M image maximum Factory Aug 7 2 ROOA None 2010 3400 Series Platform Notes The installed 3400 SDRAM is 64Mbytes Vanguard 242 Boot prom Coldloader and Image Matrix Cold loader Boot Code Han On No Release Version Board Status Comment Release Flash 7 2 ROOA or i 8M 128K CMEM 8M barlier image maximum Vanguard 340 Enhanced Boot prom Coldloader and Image Matrix Cold Boot Code loader from On No Release Version Release Board Flash Flash smm Comment 6 4 or 7 2 R00A 2 6 4 8M 8M or 128K CMEM 8M none image maximum Vanguard 340 Enhanced platform Notes ECC is supported Vanguard 342 Boot prom Coldloader Image ECC and FLASH SIMM Matrix Proprietary Page 47 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Boot Cold Code loader Versio n from Release Status Comment 32M from g 6 2 128k CMEM 8M Micron image maximum 32M from A 128k CMEM 8M Micron image maximum 32M from S 128k CMEM 8M Micron image maximum 32M from 128k CMEM 8M Micron image maximum 32M from K 128k CMEM 8M Micron image maximum 32M from 128k CMEM 8M Micron S image maximum 32M from Viking 32M DRAM Viking DIMM works only with 2 31
26. 1 1990 MIB for Network Management of TCP IP based Internets Simple Network Management Protocol SNMP J D Case M Fedor M L Schoffstall C Davin May 01 1990 Transmission Of IP Datagrams Over The SMDS Service D m Piscitello J Lawrence Mar 01 1991 Concise MIB Definitions M t Rose K Mccloghrie Mar 01 1991 Management Information Base For Network Management Of TCP IP based Internets MIDI K Mccloghrie M t Rose Mar 01 1991 A Convention for Defining Traps for use with the SNMP M Rose Editor Performance Systems International March 1991 IEEE 802 5 Token Ring MIB K Mccloghrie R Fox E Decker May 01 1991 IAB Official Protocol Standards J Postel Aug 01 1991 ICMP Router Discovery Messages S Deering September 1991 Definitions Of Managed Objects For Bridges E Decker P Langille A Rijsinghani K Mccloghrie December 1991 Inverse Address Resolution Protocol T Bradley C Brown Jan 01 1992 Multi protocol Interconnect Over Frame Relay T Bradley C Brown A Malis January 1992 Management Information Base for Frame Relay DTEs C Brown F Baker C Carvalho April 9 1992 PPP Internet Protocol Control Protocol IPCP G McGregor May 1992 PPP Authentication Protocols B Lloyd W Simpson Oct 01 1992 Status of Assigned Numbers J Reynolds J Postel July 01 1992 Proprietary Page 76 of 84 8 11 2010
27. 11 a c73cv384 xrc XRC File 2 23 2002 1 54 AM 2 n t a lt 73cv576 xrc XRC File 2 23 2002 1 54 AM CH TIOBP140 al c7Scv96 xrc XRC File 2 23 2002 1 55 4M T10BP150 e 4 gt 4 gt 17 object s Disk Free space 393 MB My Computer h 10 Once completed the 7300 shows Restarting Change your terminal speed immediately back to 9600 The unit should automatically reboot and go to ONS provided that the boot prom and ONS images are compatible Note If the ONS images are not compatible the node responds by removing the current image and prompts the user with a download cold loader message If you received this message check the table in step 9 The table contains the correct compatibility information To load a compatible ONS image repeat these steps substituting the ONS image instead of the boot prom image instruction in step 8 11 Upon completion of loading a compatible image the node restarts 8 6 Boot Prom Information for the MPC750 Controller Card Any MPC750 CPU controller card numbered 75836G01 with revision D or greater REQUIRES the new boot prom code and must not be downgraded past 1 40 You must NOT load an earlier version of boot prom or attempt to load software with a Vanguide CD prior to release 5 4 POLB This card is functionally equivalent to the original card but does require new boot prom code and cold loaders to operate This new boot prom code is release 1 40 or g
28. 836G02 system card and are running older versions of release 6 1 a new 6 1 software patch is required 6 1 T14A The system cards have a different revision PCI PCI bridge than previous system cards part number 75836G01 The new system cards are not being recognized by software older than 6 1 T14A Software patch 6 1 T14A must be installed when using part number 75836G02 For more information reference the 7300 Hardware Advisory Notice part number T0258 Proprietary Page 46 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 9 Boot Prom and Cold loader Matrix Upgrade The following tables describe the valid combinations of released flash image boot code on board flash flash SIMM and DRAM for the Vanguard 34xx 34x 68xx and 7300 platforms In the following tables the Status column can be Valid Invalid and VR Valid and Recommended Valid means that the router is basically working but some functionalities such as an option feature support might not be available Invalid means that the router is not working with such a combination VR Valid and Recommended means that the combination is valid and recommended to use according to our current knowledge Vanguard 3400 Boot prom Coldloader and Image Matrix Cold loader from Release On Board Status Comment Flash Boot Code No Release Version 7 0 P12A 7 0 P12A 16M or earlier 7 1 R0
29. 94 Classical IP and ARP over ATM M Laubach January 1994 OSPF Version 2 J Moy Mar 01 1994 The Network Address Translator NAT K Egevang P Francis May 1994 Proprietary Page 77 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 The text enriched MIME Content type N Borenstein Jan 01 1994 TN3270 Enhancements B Kelly Auburn University July 1994 The Point to Point Protocol PPP W Simpson Editor July 1994 Definitions of Managed Objects for SMDS Interfaces Using SMIv2 T Brown amp K Tesink Editors August 1994 Assigned Numbers J Reynolds J Postel October 1994 BGP IDRP of IP OSPF Interaction K Varadhan OARnet amp ISI S Hares NSFnet Merit Y Rekhter T J Watson Research Center IBM Corp December 1994 A Border Gateway Protocol 4 BGP 4 Y Rekhter T J Watson Research Center IBM Corp T Li Cisco Systems Editors March 1995 Extending OSPF to Support Demand Circuits J Moy Cascade April 1995 Requirements for IP Version 4 Routers F Baker June 1995 IP Authentication using Keyed MD5 P Metzger Piermont W Simpson Daydreamer August 1995 IP Authentication using Keyed SHA P Metzger Piermont W Simpson Daydreamer September 1995 Textual Conventions for Version 2 of the Simple Network Management Protocol SNMPv2 J Case
30. AIL this switch entry specifies the call address of the voice mail port E_164 NUMBER The digits specified in this entry represents a global E 164 number The E 164 number syntax will be used in SIP requests Any combination of above specified by summing e g H323 USE_INTERFACE _IP_ADDR ENABLE VOICE MAIL A 4 10 3 Voice Port Enhancement The E amp M interface type has been modified to operate slightly different from its original design for Transparent Voice Signaling TVS Mode This parameter is only present when Signaling Control is set to Transparent This new selection will allow the user to enable or disable audio when the signaling bits return to Idle This is useful for eliminating Echo during some Radio Communication by implementing a forced Half Duplex operation Block Audio When Idle Disabled Range Disabled Enabled Default Disabled This parameter enables disables the blocking of audio packets toward the interface during the idle signaling state Disabled Audio packets received from remote end will be sent to the interface when the interface is in the idle signaling state Enabled Audio packets received from remote end will be discarded when the interface is in the idle signaling state Note This parameter must be configured the same at both the local and remote ends of the TVS connection Otherwise a one way audio problem could result Proprietary Page 17 of 84 8 11 2010 Vanguard Networks Applications Ware Sof
31. ATAPAC 3101 PAD 3201 SPP PAD AC100 SHDLC TBOP TBOP BYPASS X32 XDLC Proprietary Page 59 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 BSTD Burroghs Poll Select TCOP TCOP BYPASS NCRBSC RS366 801 Autodialer Protocol TPDU Adaptors TPA TPDU TPA SDLC TPA 3270 TPA 2780 TPA TCP TPA UDP Node Features ATCIF AT Dial Telnet LBU DCP DSCOPE DSD NCCP BCST NUI Northern Telecom Backbone QOS Features TOW QoS Protocol Priority 5 3M QoS Diff Serv Ethernet DiffServ QoS WAN MLPPP LFI FRAME Data Comp IP FLOW o MLPPP NetFlow 5 Security and VPN Enhanced Firewall DOS mitigation Intrazone Interzone Control Plane Policies Syslog Client IPSec 3DES S W based encryption IPSec Aggressive mode SSH Hardware Accelerated Encryption amp VPN DES 3DES and AES PKI amp X 509 Digital Certificates Proprietary Page 60 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Enhanced SSH 14 Release 7 3RO0A for the Vanguard 6840 6841 Release 7 3 RO0A supports the following Applications Ware for the Vanguard 6840 6841 Each Applicatio
32. C SYSLOG Severity Range EMERGENCY ALERT CRITICAL ERROR WARNING NOTICE INFORM DEBUG Default EMERGENCY ALERT CRITICAL ERROR WARNING NOTICE Help Text The SYSLOG severity parameter selects the severity of the SYSLOG message to forward to the SYSLOG Server For TRAFFIC LOGGING Messages to be sent to the SYSLOG Server you must include NOTICE in this Severity selection Note Any combination of above may be specified by summing e g EMERGENCY ALERT Figure 3 SYSLOG Server Parameters cont Proprietary Page 21 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 4 11 3 SYSLOG Client Configuration Example Figure 4 shows a configuration example of the SYSLOG Client Feature In this example a VN3480 is configured to send its SYSLOG messages to a Kiwi SYSLOG Server 172 16 1 0 24 Kiwi Syslog Server Setup Inputs UDP Node3460 y Listen for UDP Syslog messages UDP Port 1 65535 514 Kiwi Syslog Server Node Record Alarm Selection HIGH MED Configuration Change Alarm SYSLOG Global Parameters Configure Port 23 SYSLOG Global Enable Enabled Port Type ETH Router Interface SYSLOG Server Parameters Number 1 Entry Number 1 SYSLOG Server Connection Enable ENABLED SYSLOG protocol UDP SYSLOG Server IP Address 172 16 1 253 Server UDP Port Number 514 j Configure Interface 1 SYSLOG Source Address 0 0 0 0 Interface
33. Directory table in Step 9 Proprietary Page 39 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Node Address 200 Date 8 MAR 2001 Time 11 48 08 Detailed Node Statistics Page 1 of 11 Product Type VANGUARD 7310 Bootprom Revision v1 30 lt _ Running Software Image V5 4tPO8Y4_MS_7310 6 Mar 2001 15 28 20 Size 7313580 bytes Current Software Image V5 4tP 8 1_MS_ 7318 Size 5393280 bytes Alternate Software Image Y9 4tP08Y4_MS_7310 Size 5391288 bytes The Software will reboot to alte_img power up or reset 7 MAR 2001 17 33 56 node boot O7 MAR 2001 17 42 29 watch dog timeout event lt none gt configuration change 7 MAR 2001 16 20 25 The Running Configuration uses CURRENT A Reboot will use CURRENT Compressed Configuration 1964800 bytes avail 4556 bytes 0 used Uncompressed Configuration 4063232 bytes avail 13018 bytes 0 used Press any key to continue ESC to exit Use the Procomm application to update the Boot prom Open the Procomm application to get a Data Terminal Window The settings should be 9 6k N 8 1 and RAW ASCIl transfer mode Use a regular Control Terminal Port CTP connection Activate a Force Cold Load 16 12 y y Flash Memory gt Force Cold Load gt yes Cold Boot the node 7 5 y Boot gt Node cold gt yes A Download Coldloader prompt from the CTP displays 4 Choose an appropriate speed cold
34. I FRA FRF 12 Support FRI FRA FRF 12 Support Same as 6840 6841 except no FRA and FRF 12 support IP LAN VPN IPSEC 3DES AES VPN IPSEC 3DES AES VPN IPSEC 3DES AES ATM Not supported Not supported ATM supported over T3 or E3 UBR VBR and CBR 4000 VCCs IP over ATM AnnexG over ATM Not supported Not supported ATM supported over T3 or E3 UBR VBR and CBR 4000 VCCs IP over ATM AnnexG over ATM VBIP BSC3270 to TCP IP Conversion Supported Not supported Not supported The following MIB objects are supported only in 3400 platform cdx6500T1E1VGTable The following MIB objects are supported only in 6800 platform cdx6500T1E1VGTable cdx6500TdmClkTable The following MIB objects are supported only in 7300 platform cdx6500PSTT1E1TGPortTable cdx6500PSTT1E1TGTable cdx6500STTdmtgClkGroup Al signaling types v ariant combinations support user or Network side and T1 or E1 Q Sig Euro ISDN support on T1 interfaces is now available in Release 6 5 R000 7 0 RO0A 7 1 R00 A 7 2 RO0A NTT Signaling support is currently unavailable and is targeted to be added in a future release Transparent CCS can be supported manually by means of configuring the TBOP data channel for Signaling channel and Voice Bearer channels with none for signaling Virtual port mapping table entries for voice ports must be TDM VOICE Q Sig Support now includes Basic Call Supplementary Ser
35. I F RAW ASCII direct connect Coml 19200 N81 id sd d cts 1 234 General D ata Options Not Cormected 00 00 00 8 3 Procomm Setup When Options gt Data Options gt Transfer Protocol is selected a Setup menu displays e Select RAW ASCII from the Current Transfer Protocol pull down menu e Click the Transfer Protocols button Proprietary Page 41 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 System Data mei Fax Ea Internet e np Current Transfer Protacol RAW ASCII sl 8 ees gt Upload Options Transter i I Display text IT Use IER for line pace character D Milisecond delay between characters MZ D Delay between lines 1 10th sec A Terminal Colors r Download Options A RE I Display text Colors I Overmrite existing file J Delete aborted downloads fio Seconds until download time out 8 4 Send File To send afile open the Procomm application Under the Data Menu select Send File Procomm Plus Terminal d ll SI File Edit view Options Data Tools Window Help Rapid Connect Data Modem Command Mode Alt 7 B Data Manual Connect G 4nswer Data Call Nout Disconnect Alt F2 Send File Receive File Kermit Command Capture File ALE File Clipboard Dies Doorway Mode Send Information c Clear Screen This button Reset Terminal also Sends Send Break Files Gl
36. NK SWITCH_TO_ROUTER_UPLINK 26 Router Interface Number 4 26 Router Interface Number 4 IP Interface Configurations IP Interface Configurations Entry Number 2 Entry Number 2 2 Interface Number 2 2 Interface Number 2 2 IP Address 192 168 3 1 2 IP Address 192 168 3 1 2 VLAN ID 1 2 VLAN ID 1 Entry Number 4 Proprietary Page 30 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Entry Number 4 3 Interface Number 4 3 IP Address 150 30 1 1 3 VLAN ID 2 Part No T0300 Rev B Aug 2010 3 Interface Number A 3 IP Address 150 30 1 1 3 VLAN ID 1 7 Vanguard Feature Comparison Chart Feature Vanguard 3410 3410W 3460 3480 Vanguard 6840 6841 Vanguard 7300 T1 Network Interface Specification Connectors Dual RJ 45 100 ohm Framing SF and ESF Line Coding AMI B8ZS Timing Source Int Receive T1 CSU Built In Connectors Dual RJ 45 100 ohm Framing SF and ESF Line Coding AMI B8ZS Timing Source Int Receive T1 CSU Built In Two card versions 1 12 port T1 or El RJ 45 120 ohm 2 8 port T1 or El RJ 45 120 ohm E1 75 ohm support Future Node wide CLOCK control E1 Network Interface Specification Connectors Dual RJ 45 120 ohm Dual BNC 75 ohm Framing PI CAS EI CAS CRC E1_CAS_FEBE Line Coding HDB3 AMI Timing Source Int Receive Connectors Dual RJ 45 120 ohm Dual BNC 75 ohm Framing
37. ON L A SIP SIP Connect 1 0 Caller ID E Call Hold Call Waiting Call Transfer Call Forward 3rd Party Conferencing gt P PS gt gt gt Router IP Router IPX LLC Eth IPXWAN Appletalk Bandwidth on Demand Ld Bal Router Proxy Router Discovery Network Address Transl Policy Based Routing RTP UDP IP Header Compression ETH Bridge viS ee ee ee viS mi i a a O a a DIEIEIEIEIDIEIEIEID Proprietary Page 63 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 XLB Bridge IP Tunnel GRE DHCP Server amp Client UDP Radius client Dynamic IP Address Dynamic VPN IP Multicast Protocols PIM Sparse Multicast L Network Protocols NHRP Registration OSPF BGP4 BGP IGB to BGP route Filtering BGP Multipath Load Balancing BGP Same AS as in ASPath BGP TCP MD5 Authentication VRRP FRF12 FRA only for back compatibility FRI includes FRA FR SVC DTE Interface X25 SMDS PPP Auto Dialer PPP PPP IP Header Compression PPPoE SoTCP Voice Relay Encap In IP Fractional T1 E1 Trunking Gateway for E1 only ATM Protocols ATM ATM Congestion Control IBM NETWORKING AS 400 5494 Comm Server BSC2780 HPAD TPAD BSC2780 3780 to SNA Conversion BSC3270 HPAD TPAD VBIP BSC to IP Conversion BSC3270 to SNA Conversion IBM2260 TN3270 Rem Serve
38. P address negotiation 4 8 SSH Proprietary Page 15 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 The SSH configuration parameters have been enhanced to include an idle timeout feature The default timeout is 15 minutes SSH statistics now include SSH session statistics that show the current state of the SSH sessions the username logged into the session the authentication method and the IP address and port of the user 4 9 TCP Statistics TCP statistics now include both a summary statistics menu entry and a detailed statistics entry The summary statistics table displays counts for current TCP server side sessions The detailed statistics provide more information on each TCP session Detailed statistics can be searched by server side TCP port number If the default port number 0 zero is used all sessions will be displayed 4 10 SIP Connect 1 0 Enhancements SIPconnect 1 0 is a technical recommendation put out by the SIP Forum that describes the interface between a SIP service provider network and a SIP enterprise network SIPconnect is the de facto standard for SIP Trunking The following parameter changes have been made to our product to achieve this functionality 4 10 1 SIP Connect 1 0 Parameters Change From tag When Authenticating Disabled Range Disabled Enabled Default Disabled Disabled If disabled authentication requests sent in response to a challe
39. PF Version 2 MIB fc1903Vv mib Textual conventions for version 2 of SNMP tfc2496a mib DS3 E3 Interface Type MIB Converted to SNMP version 1 from the original rfc2496 mib tfc2618a mib RADIUS Authentication Client MIB rfc2620a mib RADIUS Accounting Client MIB router_opt mib Routing option required file rs366_opt mib EIA RS366 support sdlc_opt mib SDLC protocol shdsl_opt mib Symmetric High Speed DSL slac_opt mib LLC Ethernet Frame Relay Token Ring Conversion option snabsc_opt mib SNA to BSC3270 Conversion spp_opt mib SPP protocol ss opt mib Switched Services required file tl_opt mib Physical T1 port tlel_opt mib Virtual T1 E1 port mapping table tleltg_opt mib T1 E1 for the 7300 Series tlelvg_opt mib TI E1 for the 6840 3400 34X Series tbop_opt mib TBOP protocol tcop_opt mib TCOP protocol tcpbsc_opt mib BSC3270 to TCP IP Conversion tdlc_opt mib TDLC protocol tdmclk_opt mib TDM Network Clock option tdmtgclk_opt mib TDM Network Clock option for the 7300 Proprietary Page 73 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 tftp_opt mib TFTP option tn3270_opt mib TN3270 Remote Server tnpp_opt mib Telocator Network Paging Protocol TNPP tow_opt mib TOW option tr_opt mib Token Ring opti
40. PI CAS EI CAS CRC E1_CAS_FEBE Line Coding HDB3 AMI Timing Source Int Receive Tl Framing SF amp ESF Line Coding AMI B8ZS Timing Source Int Receive T1 CSU Built In El Framing EI CAS EI CAS CRC EL CAS FEB Line Coding HDB3 AMI Channelized Data Support Protocols Supported X 25 FR TBOP PPP Maximum Number of Channels 24 T1 Maximum Number of Channels 31 El Maximum Aggregated rate 1 984 Mbps Protocols Supported X 25 FR TBOP PPP Maximum Number of Channels 24 T1 Maximum Number of Channels 31 El Maximum Aggregated rate 1 984 Mbps Protocols Supported X 25 FR TBOP PPP Max Number of Channels per T1 E1 port 24 T1 31 E1 Total No of channels per card T1 8 24 192 12 24 288 E1 8 31 248 12 31 372 Total No of channels per System 7310 T1 192 4 768 288 4 1152 7310 E1 248 4 992 372 4 1488 7330 T1 192 7 1344 288 7 2016 7330 E1 248 7 1736 372 7 2604 Note all numbers subject to processing capabilities of the 7300 Proprietary Page 31 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 ISDN PRI Data Support Switch Types User Side Only N A Bundle T1 NI 1 4ESS SESS DMS 100 European Bundle E1 ETSI Asia Bundle T1 NTT Switch Variants None Required Switch Types User Side Only N A Bundle T1 NI 1 4ESS SESS DMS 100
41. Port Subaddress field will be left blank This will insure backward compatibility without requiring reconfiguration for Hunt Group or Individual Group Subaddress functionality For customers that are not running with Hunt Group functionality and are using PBX Services Call Hold Transfer or are installing a 7300 for the first time it will now be required to utilize the new Port Subaddress parameter This parameter will be used to represent the 3 digit port subaddress required for connecting voice calls on the 7300 Platform only Like all subaddress values care must be taken not to create address conflicts by creating duplicate addresses IMPORTANT For PBX Services Call Hold Transfer to function properly on the 7300 Platform in Release 7 2RO0A or later it is required to configure the Port Subaddress parameter The following change will be made to the Vanguard Applications Ware Multimedia Feature Protocols Vanguard Voice Manual Port Subaddress 73xx Platform Only Range 0 3 digits Default Blank Description Specifies a Port Subaddress to uniquely identify this port This parameter must be configured in order to use PBX services on the port The Port Subaddress must not conflict with any other Port Subaddress or Group Subaddress configured in the node Note For PBX Services Call Hold Transfer to function properly on the 7300 Platform in Release 7 2RO0A or later it is required to configure the Port Su
42. RO0A Part No T0300 Rev B Aug 2010 ASYNC BYPASS ADSPAD SLIP TNPP TNPP ROUT X 42 GSC T3POS T3POS over TCP DATAPAG 3101 PAD 3201 SPP PAD AC100 Serial Synchronous Protocols NON IBM SHDLC TBOP TBOP BYPASS X32 XDLC Serial Character Oriented Protocols NON IBM BSTD Burroghs Poll Select TCOP TCOP BYPASS NCRBSC RS366 801 Autodialer Protocol TPDU Adaptors TPA TPDU TPA SDLC TPA 3270 TPA 2780 TPA TCP TPA UDP Node Features ATCIF AT Dial Telnet D Dj D LBU D Dir D DCP D D DSCOPE DSD NCCP BCST NUI Northern Telecom Backbone QOS Features TOW DIDJ D QoS Protocol Priority 5 3M QoS Diff Serv D Dir D Ethernet DiffServ QoS WAN D Dir D Proprietary Page 70 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO00A Part No T0300 Rev B Aug 2010 MLPPP LFI FRAME Data Comp IP FLOW o MLPPP NetFlow 5 Security and VPN Enhanced Firewall DOS mitigation Intrazone Interzone Control Plane Policies Syslog Client IPSec 3DES S W based encryption IPSec Aggressive mode SSH Hardware Accelerated Encryption amp VPN DES 3DES and AES PKI amp X 509 Digital Certificates Enhanced SSH
43. Services and Segmentation AS 400 5494 Communications Server Protocols LLC2 X 25 QLLC SDLC FR RFC1490 Characteristics HDX FDX TWA Network QLLC X 25 Frame Relay Annex G Frame Relay RFC 1490 Host Protocols LLC2 Frame Relay RFC1490 LAN Token Ring 4 or 16 mbps Ethernet 802 3 10 mbps Ethernet2 WAN Physical Interface V 21 V 24 V 35 Protocols LLC2 X 25 QLLC SDLC FR RFC1490 Characteristics HDX FDX TWA Network QLLC X 25 Frame Relay Annex G Frame Relay RFC 1490 Host Protocols LLC2 Frame Relay RFC 1490 LAN Token Ring 4 or 16 mbps Ethernet 802 3 10 mbps Ethernet2 WAN Physical Interface V 21 V 24 V 35 Same as 6840 684 lexcept Characteristics no HDX Other SNA protocols BSC3270 HPAD TPAD BSC2780 3780 IBM 2260 PAD TCOP TBOP NCRBSC HPAD TPAD Pad Scope BSC3270 HPAD TPAD BSC2780 3780 IBM 2260 PAD TCOP TBOP NCRBSC HPAD TPAD Pad Scope TBOP All others not supported BSC3270 to SNA Conversion 256 Devices Supported 256 Devices Supported 2 000 Devices Supported Proprietary Page 33 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 BSC2780 3780 to SNA LUO Conversion Supported on the 6455 256 Devices Supported Supported on the 6455 256 Devices Supported 256 Devices Supported Frame Relay FR
44. State Enabled SYSLOG Type EVENT TRAFFIC Configure IP Interface AUTHENTICATION ACCOUNTING Table SYSLOG Facility Code Override NONE IP Address 172 16 1 2 SYSLOG Severity EMERGENCY ALERT CRITICAL ERROR SYSLOG High Queue Threshold 1500 Configure IP Parameters Internal IP Address 172 16 1 1 1 1 1 1 1 1 Figure 4 SYSLOG Client Configuration Example Proprietary Page 22 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 4 12 Firewall Control Plane polices and Firewall Intrazone Policies 4 12 1 Overview Firewall Control Plane polices and Firewall Intrazone polices control traffic destined to the firewall in the same way general firewall policies control traffic between zones across the firewall These policies provide finer control to traffic terminating at the router itself Firewall policies will have an option to log traffic matching the firewall policy These entries are recorded in the new Traffic Log 4 12 2 Firewall Control Plane Policies Firewall control plane policies are used to filter traffic terminating at the router itself A separate set of policies is advantageous for several reasons In many cases traffic may not need filtering through the router In these cases subjecting all packets to the policies is known to significantly increase the CPU utilization By separating the policy control fo
45. Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 lt Vanguorg NETWORKS Applications Ware Software Release 7 3 RO0A Release Notice Proprietary Page 1 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO00A Part No T0300 Rev B Aug 2010 Table of Contents 1 Overview 2 Applications Ware 2 1 Applications Ware Licenses and Upgrades 2 1 1 Applications Ware Base Licenses 2 1 2 License Upgrades 2 2 Default Software Images and Functionality 2 3 Software Upgrade to 7 3 RO0A Tech Tip 2 4 License Upgrades 2 5 Memory Requirements for Applications Ware Release 7 3RO0A 3 Products Supported 4 New Features 4 1 New Hardware Platform 3410W Access Services Gateway 4 2 MD5 BGP peer authentication 4 3 NHRP Next Hop Resolution Protocol GRE enhancements in support of NHRP 4 4 7300 Platform System Card New Revision V3 4 5 NULL ROUTES 4 6 4 8 4 9 TCP Statistics 4 10 SIP Connect 1 0 Enhancements 4 10 1 SIP Connect 1 0 Parameters 4 11 SYSLOG Client 4 11 1 Overview Proprietary Page 2 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 4 11 2 SYSLOG Configuration 4 11 3 SYSLOG Client Configuration Example 4 12 Firewall Control Plane polices and Firewall Intrazone Policies 4 12 1 Overview 4 12 2 Firewall Control Plane Policies 4 12 3 Firewall Intrazone Policies 4 13 Denial of Service
46. Ware Name Source Version String Description Filename Filename IPSAFE Applications Ware 73ROOAbbI11 xre_ 7 3 RO0A_ IPSAFE_3400 73ROOAbb 1 1 des SNA Applications Ware T3ROOAbb12 xre_ 7 3 ROOA_ SNA _ 3400 73ROOAbb12 des Multi service Applications Ware 73R00Abb15 xre 7 3 ROOA_ MS_ 3400 32RO0Abb15 des Proprietary Page 55 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Release 7 3 July 2010 Updates Part No T0300 Rev B Aug 2010 VG3410 W Release 7 3 UPGRADE LICENSE Upgrade License Legend L in license D in default image A add on feature upgrade license SNMP v1 Security Services Encryption Acc AS400 BSC Advanced Voice SPECIALS SNMP v3 TELNET TFTP CLI Embedded Web HTTPD ATPAD APAD ISDN BRI NOAM ISDN BRI EURO ISDN BRI ASIA ISDN T1 E1 PRI Data NA Default ISDN T1 E1 PRI Data European ISDN T1 E1 PRI Data Asia ISDN T1 E1 PRI Voice incl sign NA ISDN T1 E1 PRI Voice incl sign Euro G 723 1 lt lt 3460 80 only G 729A lt lt 3460 80 only CVSELP lt lt 3460 80 only Centralized Voice Switching Proprietary Page 56 of 84 lt lt 3460 80 only 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010
47. Ware RFC Compliance 18 Appendix 18 1 CR17642 amp CR17643 Enhancements Special Upgrade Information 19 Product Declarations and Regulatory Information 19 1 Warnings and Cautions 19 2 CE Marking 19 3 Declarations of Conformity Proprietary Page 4 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Overview This notice contains update information for Release 7 3 ROOA of the operating software for the following Vanguard platforms Vanguard 3410 Vanguard 3410W Vanguard 3460 Vanguard 3480 Vanguard 6840 Vanguard 6841 Vanguard 7310 Vanguard 7330 The following Vanguard platforms are not supported in Release 7 3 RO0A Platform Latest Supported Release Vanguard 100 Release 5 3M Vanguard 200 Release 5 1M Vanguard 242D 340 Enhanced 342 Release 7 2 RO0A Vanguard 300 Release 5 4 Vanguard 305 Release 5 5 Vanguard 311 Release 5 1M Vanguard 311PLUS 312PLUS Release 5 3M Vanguard 320 Release 6 4 ROOA Vanguard 340 Release 7 0 RO0A Vanguard 6425 6430 6450 Release 6 0 RO0A Vanguard 6435 6455 Release 7 0 RO0A Vanguard 6520 Release 5 5 Vanguard 6560 Release 6 0 RO0A 6500PLUS Release 5 1M 650D Release 5 0C Voice feature on the Vanguard 100 Release 5 2 This notice supplements the full set of the Vanguard user documentation 2 Applications Ware This section explains how the Applications Ware software is organized implemented and modified 2 1 Applications Ware Licenses and Up
48. are See the MIB Files for Options Protocols section below 16 3 MIB Files for Options Protocols This table lists the contents of options and protocol MIB files for Vanguard products Use this table to determine which MIB files you need to download Proprietary Page 71 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Download this MIB File Part No T0300 Rev B Aug 2010 If you want this option protocol or base MIB software adspad_opt mib ADS Protocol alc_opt mib ALC protocol atm_opt mib Asynchronous Transfer Mode best opt mb Broadcast bgp4_opt mib Border Gateway Protocol 4 bn opt mb ISDN BRI protocol bridge_opt mib Bridging option bsc2780_opt mib BSC2780 protocol bsc3270_opt mib BSC3270 protocol bstd_opt mib Burroughs Poll Select protocol cdx_6500 mib Required base MIB for Vanguard Products MIBs dc_opt mib Data Compression option dcp_opt mib Data Connection Protection option de_opt mib Data Encryption option dsd_opt mib Digital Sharing Device Option el_opt mib Physical E1 port eia_opt mib EIA protocol required file for serial protocol support eth_opt mib Ethernet option eth_sw_opt mib Ethernet Switch Option frdce_opt mib Frame Relay DCE option frdte_opt mib Frame Relay DTE option fri_opt mib Frame Relay option f
49. ate in the DMVPN Dynamic Multipoint Virtual Private Network model In the DMVPN model NHRP was required to address the burden of the HUB router in managing its remotes primarily in the hubs requirement to add configuration for each of the remotes in the network Using NHRP the Hub no longer has the need to modify add to the configuration for any remotes added to the network The VG first release of NHRP support includes the following e Actas Spokes in the Hub amp Spoke network e Use GRE to transport data to the Hub GRE only e Support dynamic IP addressing on the WAN interface The First release of Vanguard Networks NHRP implementation does NOT require the Vanguard routers to e Actas Hubs e Bean NHRP Server e Support direct Spoke to Spoke tunnels e Support dynamic caching of mappings The Spokes will always have a static NHRP mapping for the Hub The Hub must have a static IP address that is known by the Spokes Proprietary Page 10 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 4 3 1 GRE enhancements in support of NHRP In support of the NHRP implementation an optional GRE Key Tunnel Key is needed to provide a way for the hub routers to map incoming GRE packets to specific tunnel interfaces Each tunnel interface on a router must have a distinct GRE Key All tunnels in a given DMVPN must have the same key NHRP is configured in the Tunnel configuration found
50. back in CR17579 17354 Changing the Master Voice Port DSP Image Selection and Booting the Voice Port causes the DSP to reset When the master voice port DSP Image selection is changed and the port is booted the DSP associated with the Voice Port will reset requiring a Node Boot Workaround Boot the node when modifying the DSP image selection CR17595 ISDN calls may be initiated with no data incoming The node brings up ISDN calls after the previous connections were disconnected even when no data was incoming It is caused by an inappropriate value configured in Idle Disconnect Timer Workaround Configure the Idle Disconnect timer to be at least 3 times as big as Add Remove Bandwidth Wait Time Here are configuration samples Working Configuration Non Working Configuration Add Bandwidth Wait Time 10 Add Bandwidth Wait Time 10 Remove Bandwidth Wait Time 10 Remove Bandwidth Wait Time 10 Idle Disconnect Timer 30 Idle Disconnect Timer 25 CR17872 Incorrect Vanguide Builder Error Message when exceeding available flash size of the 34X In Vanguide Software Builder selecting Products 340E 342 or 242d you may receive the following splash messages if the Selected Option Size estimated calculation exceeds 8 000 000 due to the image size exceeding the on board flash device limitation The on screen message seen is as follows ERROR No XRC file has been created in the TEMP directory Failed to create an XRC file Please v
51. baddress parameter Also to use the Group Subaddress for it s intended purpose Hunt Group Proprietary Page 82 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 19 Product Declarations and Regulatory Information The following sections provide information about standards compliance safety statements and Type Approvals 19 1 Warnings and Cautions The following special notices apply to all equipment handling procedures in this installation guide 4 Warning Ports capable of connecting to ports on other apparatus are defined as Safety Extra Low Voltage SELV To conform with EN60950 ensure that these ports are only connected to ports of the same type on other apparatus Les ports qui sont susceptibles d tre connect s a des quipements sont d sign s comme TBTS Pour garantir la conformit a la norme EN 60950 n interconnecte ces ports qu avec des ports du m me type sur des autres mat riels Anschlusse die mit anderen Geraten verbindet werden konnen sind als SELV beschrieben Um Konformitat mit EN 60950 zu versichern sichern Sie es da diese Anschlusse nur mit den des selben Type auf anderen Geraten verbindet werden 19 2 CE Marking The mark in the following diagram appears on each Vanguard Series product and the statement that follows explains its significance LE This product is CE marked to indicate compliance with the foll
52. boot code 32M from Viking 32M DRAM Viking DIMM works only with 2 31 boot code 32M from Viking 32M DRAM Viking DIMM works only with 2 31 boot code 32M from 128k CMEM 8M Micron image maximum ECC not supported 32M from i 128k CMEM 8M Micron image maximum ECC not supported 32M from i 128k CMEM 8M Micron image maximum 32M from 128k CMEM 8M Micron image maximum 32M from 128k CMEM 8M Micron image maximum Proprietary Page 48 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A 6 3 to 7 2 32M from Micron Part No T0300 Rev B Aug 2010 128k CMEM 8M image maximum 6 3 to 7 2 32M from Viking Invalid Viking 32M DRAM DIMM works only with 2 31 boot code 6 3 to 7 2 32M from Viking Viking 32M DRAM DIMM works only with 2 31 boot code 6 3 to 7 2 32M from Viking Viking 32M DRAM DIMM works only with 2 31 boot code Vanguard 342 platform Notes The Vanguard 342 uses 32Mbyte DRAM If the DRAM DIMM s vendor is Viking Viking Part Number VI8GU083236BTB 2 31 boot code must be used Boot code 2 1 was released with 6 2 Boot code 2 1 1 was based on 2 1 and is compatible with the old released software It contains the watchdog FER changes Boot code 2 1 1 was released with 6 2 S100 Boot code 2 20 which is not mentioned
53. ddress Transl Policy Based Routing RTP UDP IP Header Compression ETH Bridge XLB Bridge IP Tunnel GRE DHCP Server amp Client UDP Radius client Dynamic IP Address Dynamic VPN IP Multicast Protocols PIM Sparse Multicast L Network Protocols NHRP Registration OSPF BGP4 BGP IGB to BGP route Filtering BGP Multipath Load Balancing BGP Same AS as in ASPath BGP TCP MD5 Authentication olr rlrlripltr rr olr lelero me lele olr lelero me lele O III UI III UI III VRRP FRF12 FRA only for back compatibility FRI includes FRA FR SVC DTE Interface X25 SMDS PPP Auto Dialer D Proprietary Page 58 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 PPP PPP IP Header Compression PPPoE SoTCP Voice Relay Encap In IP Fractional T1 E1 Trunking Gateway for E1 only ATM ATM Congestion Control 3410 AS 400 5494 Comm Server only gt gt BSC2780 HPAD TPAD BSC2780 3780 to SNA 3410 Conversion only gt gt BSC3270 HPAD TPAD VBIP BSC to IP Conversion BSC3270 to SNA Conversion IBM2260 TN3270 Rem Server 3410 Conversion only gt gt LLC ETH LLC FR SDLC 3410 only gt gt ASYNC BYPASS ADSPAD SLIP TNPP TNPP ROUT X 42 GSC T3POS T3POS over TCP D
54. e they have been 17962 7 2P01C Node will not boot from alternate if current is corrupt 17965 7 2 P02A Hardware Status 7300s Hardware Status does not reflect the startup 17969 7 2 RO0A ISDN BRI x 25 virtual port boot does not work 17970 7 2 T02A SNMP MIB does not reflect loss of carrier correctly 17972 7 2 102A SSH password does not work 17986 7 2 PO1F BGP session fails to negotiate 17988 7 2 T02A 6480 BRI Leased bonded 128K link does not work with 6840 17992 7 2 P02A Feature Need TFTP image loading capability in 34xx bootprom 18011 7 2 BGP Load balancing produces an imbalanced result 18023 Feature Implement a half duplex audio path using E1 CAS signaling 18026 7 2 P01F Feature FW PPoE Cannot filter traffic destined to the router 18029 7 2 New T1 E1 cards not showing up in power up diagnostics with 3 Serial 18032 V7 1 T17A MLPPP port not recovering after outage using T1 links w remote stand 18033 7 2RO0A Feature MOI Requests full support of Voice Billing Enhancements on 6 5T25C amp 18034 7 2 T01E PPPoE INITIALIZATION ERROR No thernet port context alarm after 18040 7 2 PO1H TCP port lock up prevents remote access to the node node must be 18042 NA BGP hangs intermittently with 2 BGP Peers 18043 7 1P25A Serial Frame Relay Port has constant CRC errors 18044 7 1 5100 Qos not marking DSCP at IPSec over Ethernet WAN port 18059 7 2P01H Feature SSH is still stranding TCP sessions 18072 7 2 P01K Firewall No Policy Action Status on Firewall Ses
55. ear XOFF Alt Hen Chat DEES Cmd Mod Send Fax Explorer DOS Poel VI RAWASC Chat window H i w d cd oe 1339 Send upload a file to speit H ttor Window Not Connected 00 00 00 Send the correct file using one of the enclosed c73 loaders below c73cv115 xrc for 115 Kbps c73cv288 xrc for 28 8 Kbps c73cv192 xrc for 19 2 Kbps c73cv384 xrc for 38 4 Kbps c73cv576 xrc for 57 6 Kops c73cv96 xrc for 9 6 Kops Proprietary Page 42 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Note To reduce the download time Vanguard Networks recommends c73cv115 xre for 115 Kbps Part No T0300 Rev B Aug 2010 7 Once the download is complete change the terminal speed to the appropriate cold loader speed chosen in step 4 Download the Bootprom xrc file The required Boot prom version such as T10BP111 xrc can be acquired from the directory containing the same name C Vanguard SFW_IMGS 73 0 COLDLOAD T10BP1 Open the Procomm Plus Terminal Manual application a Select Send File under the Procomm Data Menu b Select the correct boot prom version Choose the correct boot prom directory that includes the cold loaders The example below shows the 7300 Series Boot prom Directories T10BP1 refers to T10BP110 T10BP150 T10BP111 T10BP151 T10BP130 T20BP200 T10BP140 T30BP300 Boot prom Directory ONS Image Compatibility Boot prom Version T10BP110 5 4 P08A 5 4 P08B
56. erence REFER is not working 17810 7 2iROOM PPP IPCP learned IP addr not shown in IP Interface stats 17851 7 05100 BGP peer error BGP FSM Error Peer 1 CurrState 0 CurrEvt 2 17869 Feature Datapac 3201 protocol support on the 3400 platform 17886 70T16Z Feature Node freeze after reach 100 CPU Need CPU reset to recover 17890 7 2RO0A TOS Stat missing from Cache Statistics 17893 7 1R00a Out of sequence large pings are failing with ACL IP 51 rs ovfl alarms 17895 7 2RO0A Domain name field is too short 17904 7 2RO0A Unable to process fragmented ICMP messages when access control is 17909 7 2 RO0A Bypass stations buffer packets during heavy load and stop transmitting 17910 7 2RO0A DHCP Server issues with WIFI networks 17911 7 2 P01B arp may set data packet priority to exp_no_drop arputil c 1091 17923 7 2RO0A Sudden Buffer Depletion when running SIP Voice Loading Test 17927 7 2RO0A Constant Node Crash when T1 ISDN is configured on Int 1 17930 7 2 RO1A Node Crash Memory Protection PC stopped at_tcp_ close 17931 7 2 T01B The rate limit feature was not included in the 342 amp 242 platforms 17932 7 2 RO1A IPSec Aggr Mode Node crash due to PPPoE Port configuration 17936 Feature Add support for Bridge Priority to ethernet switch code 17942 7 1 5100 HTTPD will only accept the last address in an httpd access list 17954 7 2RO0A All IP Sec tunnels go down after booting IPsec parameters no CTP 17955 7 2 T02A Node boot needed to enable ISDN virtual ports onc
57. erify correctness of the settings in the Settings dialog Also ensure that there is at least 30MB available on your hard disk and that available Virtual Memory is a least 16MB You should now review and save to a different location the LOG files from the installation s TEMP directory Do you want to review and save the error logs Workaround Deselect Feature Protocols until the Selected Option Size is below 8 000 000 Note that this calculation will be corrected in the next release of Vanguide Software Builder CR17677 IP Parameter Boot may result in a BGP session boot Any changes made to BGP related parameters under IP parameters and an IP parameter boot is performed all BGP sessions will also be booted reset This will interrupt live BGP peer sessions and result in network BGP resynchronization Proprietary Page 29 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Workaround Users should be aware that if a change is made to any of these parameters and a subsequent IP parameter boot is performed then all BGP peer sessions will reset to implement the change BGP to RIP Enable Disabled BGP to RIP Default Filter Deny BGP to RIP Nondefault Route Override Disable BGP to RIP Default Route Override Disable BGP to RIP Default Metric 1 To minimize the impact on the user perform the IP parameter boot during a scheduled maintenance window to av
58. ev B Aug 2010 1 Record Route IP Options Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of IP packets with the Record Route IP options bit set in the IP packet header 1 Timestamp IP Options Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of IP packets with the Timestamp IP options bit set in the IP packet header 1 Security IP Options Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of IP packets with the Security IP options bit set in the IP packet header 1 Stream IP Options Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of IP packets with the Stream IP options bit set in the IP packet header 1 Source Route IP Options Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of IP packets with the Loose Source Route or the Strict Source Route IP options bit set in the IP packet header 1 Unknown Protocol Protection Disabled Range Enabled Disabled Default Disabled This parameter controls the discarding of IP packets with an unknown protocol value in the IP packet header If enabled a packet is discarded if the protocol value is 143 or greater 1 Ping Of Death Protection Disabled Range Enabled Disabled Default
59. g 2010 VG6840 VG6841 encryption module Release 7 3 July 2010 Updates Release 7 3 UPGRADE LICENSE Upgrade License Legend L in license D in default image A add on feature upgrade license Security Services Encryption Acc AS400 BSC Advanced Voice SPECIALS SNMP v1 SNMP v3 TELNET TFTP CLI Embedded Web HTTPD ATPAD APAD ISDN BRI NOAM ISDN BRI EURO ISDN BRI ASIA ISDN T1 E1 PRI Data NA Default ISDN T1 E1 PRI Data European ISDN T1 E1 PRI Data Asia ISDN T1 E1 PRI Voice incl sign NA ISDN T1 E1 PRI Voice incl sign Euro G 723 1 G 729A CVSELP Centralized Voice Switching Voice Routing Services Half Duplex Radio Proprietary Page 62 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 G 723 1 G729A G711 can t add T 38 G 723 1 G711 can add T 38 G 729AB G711 can add T 38 G 723 1 G729A G711 T 38 but no VAD Centralized Voice Switching Voice Routing Services FAX ITU T 38 Vanguard T1 E1 PRI Digital Voice Server Half Duplex Radio T 38 w G 723 amp G 711 for T1 E1 T 38 w G 729a amp G 711 for T1 E1 Voice Relay with G 723 1 and G 729a Voice Relay Encapsulated in IP SoTCP H 323 v 2 Standards Based Voice H 323 H 323 Caller ID VOICE IP ENCAPSULATI
60. grade to a previous release you must reload the configuration saved from that release or risk corrupting the configuration 8 1 Software Loader Software Loader automatically upgrades or downgrades the boot prom When an image is loaded and it requires a version of boot prom different from the one currently loaded Software Loader changes the boot prom to successfully load the image For more information on boot prom image compatibility refer to the Boot prom Directory table on page 28 The boot prom can be uploaded and downloaded manually using a communication application such as Procomm 8 2 Procomm Procedure Below is a step procedure on how to cold load the Boot prom using Procomm Communication software This procedure example was documented using a Vanguard 7300 Series router The figure on page 29 shows the various product directories Note Boot prom revision 3 00 is current for release 6 5 RO00 or greater 7300 series routers using the IBM750FX CPU and MPC750 CPU 1 To determine the current version of Boot prom loaded on your Vanguard perform these steps Step Action a Access the Console Terminal Program s CTP Main Menu b Select Option 5 Status statistics c Select Option 1 Node Stat from the Status statistics menu The Node Stats displays the Boot prom Revision 7300 Series Examples Version 1 10 1 11 1 30 1 40 1 50 1 51 Version 2 00 or Version 3 00 Note Refer to the Boot prom
61. grades The Release 7 3 ROOA Applications Ware is divided into four base licenses and four to five upgrade licenses depending on the platform Customers are required to purchase only one base license and can purchase optional upgrade licenses to add to the base license Compatibility of upgrade licenses with base licenses and various products is dependent upon a specific product and its capabilities Proprietary Page 5 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Applications Ware Base Licenses IP Applications Ware License 7310 7330 IP SAFE Applications Ware License 3400 and 6800 o Note Beginning with Release 7 1ROOA the IPSafe Applications Ware license includes SSH Server with external Radius Authentication and software based IPSec VPN SNA Applications Ware Multi Service Applications Ware License Upgrades Voice Applications Ware License Upgrade Encryption Acceleration Applications Ware License Upgrade AS 400 BSC Applications Ware License Upgrade Advance Voice Premium Services SIP Security Services Note A license refers to both a legal document that allows a customer to use features and to the software that contains the features One base license must be purchased for each hardware platform 2 2 Default Software Images and Functionality Each license contains a large number of software features and functions In addition each hardware platform has a
62. grams in the presence of subnets J C Mogul Oct 01 1984 Internet Standard Subneting Procedure J C Mogul J Postel Aug 01 1985 Proposed Bootstrap protocol BOOTP for ARPA Internet W Croft J Gilmore Sept 01 1985 Requirements for Internet Gateways R Braden J Postel Jun 01 1987 Standard For The Transmission Of IP Datagrams Over IEEE 802 Networks J Postel J k Reynolds Feb 01 1988 Nonstandard For Transmission Of IP Datagrams Over Serial Lines SLIP JIL Romkey Jun 01 1988 RIP Version 2 Carrying Additional Information G Malkin January 1993 Assigned values used in network protocol implementations J Reynolds J Postel Mar 01 1990 Distance Vector Multicast Routing Protocol D Waitzman C Partridge S Deering Nov 010 1988 Telnet Terminal type Option J Vanbokkelen Feb 01 1989 Host Extensions for IP Multicasting S Deering Aug 01 1989 Requirements for Internet hosts communication layers R T Braden Oct 01 1989 Requirements for Internet hosts application and support R T Braden Oct 01 1989 Compressing TCP IP headers for low speed serial links V Jacobson Feb 01 1990 Proprietary Page 75 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Structure And Identification Of Management Information For TCP IP based Internets M t Rose K Mccloghrie May 0
63. he 3410W ASG has the performance and headroom needed in an all IP future while Vanguard Networks customers are assured of investment protection for their existing applications Hardware details can be found in the user manual titled 3400 Installation Guide Software details can be found in the various software manuals on the Vanguard Networks website at http www vanguardnetworks com support documentation overview htm 3410W Daughter Card Support Daughtercard 3400 Series Platform Description Product Code 3410 3410W 3460 3480 DC Site1 DCSite1 DCSite1 DCSite2 DC Site1 DCSite2 2P SDC 2 Port Serial 1130 10004 56K DSU 68472 Dual E amp M 65729 Dual FXS 68372 BRI Voice 68525 FT1 120 O 49666 Proprietary Page 8 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 FE1 75 1 49669 FE1 120 49716 FT1 120 1600 00001 FE1 75 1600 00075 FEI 120 D 1600 00120 FXS FXO 80019 G SHDSL 1152 10009 Quad FXO 1152 10035 Quad FXS 1152 10034 ISDN BRI S T 68525 ISDN BRI S T 1152 10005 ISDN BRI U 68434 V 11 DCE Serial 49649 V 24 DCE Serial 46946 V 35 DCE Serial 49647 V 36 DCE Serial 49648 V 11 DTE Serial 49661 V 24 DTE Serial 49658 V 35 DTE Serial 49659 V 36 DTE Serial 49660 V 90 Modem 1152 10003 4 2 MD5 BGP peer authentication BGP Peer Authentication is the newest method t
64. i June 1999 Proprietary Page 80 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 RADIUS Authentication Client MIB B Aboba G Zorn Microsoft June 1999 RADIUS Accounting Client MIB B Aboba G Zorn Microsoft June 1999 Multiprotocol Encapsulation over ATM Adaptation Layer 5 D Grossman Motorola Inc J Heinanen Telia September 1999 RFC 2684 replaces RFC 1483 The Multi Class Extension to Multi Link PPP C Bormann Universitaet Bremen TZI September 1999 Interoperability Rules for Multicast Routing Protocols D Thaler Microsoft October 1999 RTP Payload for DTMF Digits Telephone Tones and Telephony Signals S Petrack Metatel May 2000 Remote Authentication Dial In User Service RADIUS C Rigney S Willens Livingston A Rubens Merit W Simpson Daydreamer June 2000 RADIUS Accounting C Rigney Livingston June 2000 SIP INFO Method S Donovan dynamicsoft October 2000 Session Initiation Protocol SIP Definitions of Managed Objects for High Bit Rate DSL 2nd Generation HDSL2 and Single Pair High Speed Digital Subscriber Line SHDSL Lines Processing B Ray PESA Switching Systems R Abbi Alcatel May 2002 Internet Group Management Protocol IGMP Version 3 B Cain Cereva Networks S Deering I Kouvelas CISCO Systems B Fenner AT amp T Labs A Thyagarajan Er
65. icates Enhanced SSH 15 Release 7 3RO0A for the Vanguard 7310 7330 This section provides detailed information about the Applications Ware available for Vanguard 7300 Release 7 3 RO0A makes available the following Applications Ware for the Vanguard 7300 Each Applications Ware package supports a suite of default features Other features however can be added by using Vanguard Software Builder Source Filename Vanguard 7310 Applications Ware Name Version String Description Filename IP 7 3 ROOAtI1 1 xrc 7 3 ROOA_ IP _7310 73ROOAtI1 1 des SNA 7 3 ROOAt12 xrc 7 3 RO0A_ SNA _7310 7T3ROOAt12 des Multi Service 7 3 ROOAtI5 xrc 7 3 RO0A_ MS_7310 7T3ROOAt15 des Vanguard 7330 Applications Ware Name Source Filename Version String Description Filename IP 73RO00Au1 1 xre 7 3 ROO0A_ IP _7330 73RO0Au1 1 des SNA 73RO00Au12 xre 7 3 RO0A_ SNA _7330 73RO0Au12 des Multi Service 73R00AAu15 xrc 7 3 R00A_ MS_7330 73R00Au15 des Proprietary Page 66 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Release 7 3 July 2010 Updates Part No T0300 Rev B Aug 2010 VG7300 VG7310 Release 7 3 UPGRADE LICENSE Upgrade License Legend L in license D in default image A add on feature upgrade license SNMP v1 Security Service
66. icsson October 2002 SIP REFER Method R Sparks dynamicsoft April 2003 18 Appendix 18 1 CR17642 amp CR17643 Enhancements Special Upgrade Information Prior to Release 7 0ROOA the 7300 Platform used the Group Subaddress Hunt Group parameter to Proprietary Page 81 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 replace the four digit Virtual Port Number with a usable 3 digit Port Subaddress for connecting voice calls This 3 digit Port Subaddress could also be used for a Hunt Group application In Release 7 0ROOA the PBX Services functionality was enhanced to include the ISDN Voice Interfaces and to enable PBX Services by default This change created a conflict between the operation of Hunt Groups and PBX Services Call Transfer on the 7300 Platform Beginning in Release 7 2RO0A for the 7300 Platform only a parameter has been introduced into the Virtual Voice Port Record The new parameter is called Port Subaddress This Port Subaddress parameter can now be used in place of the Group Subaddress Hunt Group parameter for connecting voice calls on the 7300 Platform This restores the ability to use Hunt Groups and PBX Services together on the 7300 Platform The upgrade from any prior release to release 7 2ROOA is handled in the following manner The populated Group Subaddress Hunt Group field will be brought forward The new
67. ier Protocols SDLC Characteristics HDX FDX TWA Network QLLC X 25 Frame Relay Annex G Host Interface SDLC PTP SDLC MP X 25 IBM NPSI Physical Interface V 21 V 24 V 35 Protocols SDLC Characteristics HDX FDX TWA Network QLLC X 25 Frame Relay Annex G Host Interface SDLC PTP SDLC MP X 25 IBM NPSI Physical Interface V 21 V 24 V 35 Same as 6840 684 lexcept Characteristics no HDX Proprietary Page 32 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 LLC2 SNA Conversion Protocols LLC2 X 25 QLLC SDLC FR RFC1490 Characteristics HDX FDX TWA Network QLLC X 25 Frame Relay Annex G Frame Relay RFC1490 Host Protocols SDLC PTP SDLC MP X 25 IBM NPSD LLC2 Frame Relay RFC1490 LAN Ethernet 802 3 10 mbps Ethernet2 WAN Physical Interface V 21 V 24 V 35 Protocols LLC2 X 25 QLLC SDLC FR RFC1490 Characteristics HDX FDX TWA Network QLLC X 25 Frame Relay Annex G Frame Relay RFC1490 Host Protocols SDLC PTP SDLC MP X 25 IBM NPSD LLC2 Frame Relay RFC1490 LAN Ethernet 802 3 10 mbps Ethernet2 WAN Physical Interface V 21 V 24 V 35 Same as 6840 6841except Characteristics no HDX 6 Enblock Signaling Support only at this time 5 Q Sig Support now includes Basic Call Supplementary
68. ige ma gebliche Bestimmungen der Richtlinie 1999 5 EG erf llt Greek Amien Zu uu Opgaons Aw tov napdvtoc n etapsia Vanguard Networks Gi dnver t n mapovdoa ovoksv po u o oynt Vanguard Router zAnpoi tic BaowK s azmaitiosic Ka Ads PaoiKk c mpo mo osis TNG Odnyiacs 1999 5 E K Italian Dichiarazione di conformit Con la presente Vanguard Networks dichiara che il router Vanguard soddisfa i requisiti essenziali e le altre disposizioni pertinenti della direttiva 1999 5 CE Portuguese Declara o de Conformidade Atrav s da presente a Vanguard Networks declara que este encaminhador Vanguard se encontra em conformidade com os requisitos essenciais e outras disposi es relevantes da Directiva 1999 5 CE Spanish Declaraci n de conformidad Por la presente declaraci n Vanguard Networks declara que este encaminador Vanguard cumple los requisitos esenciales y otras cl usulas importantes de la directiva 1999 5 CE Swedish verensst mmelsef rklaring Vanguard Networks f rklarar h rmed att denna Vanguardrouter verensst mmer med de v sentliga kraven och vriga relevanta stadganden i direktiv 1999 5 EG Proprietary Page 84 of 84 8 11 2010
69. in the above matrix is the same as 2 1 1 except for the version string Boot code 2 30 is released with 6 3 ROO0A It is based on 2 1 1 The ECC card is supported by the Boot code 2 30 and release 6 3 ROOA or later Coldloader in 6 3 RO0A or later was improved by adding valid flash address checking Boot code should be updated to 2 31 for when a SDRAM DIMM from Viking is used Vanguard 6800 Series Boot prom Coldloader Image Matrix No Release Boot Code Version Cold loader from Release On Board Flash SAN DISK Status Comment 6 5 P30A 1 06 7 0 RO0A 4M None 7 1 RO0A 7 2 RO0A 1 07 7 1 RO0A 7 2 RO0A 4M For 7 0 ROOA and 7 1 RO0A 1 07 boot prom is mandatory For 7 0 ROOA 7 1 ROOA amd 7 2 ROOA 1 07 boot prom is mandatory Vanguard 7300 Series Boot prom Coldloader Image Matrix Proprietary Page 49 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Sys Module Boot Code Version Cold loader from Release Compact Flash Status Comment MPC750 CPU 1 50 6 1 to 6 4 2M CMEM Compressed MPC750 CPU 6 1 to 6 4 2M CMEM Compressed MPC750 CPU 6 1 to 6 4 2M CMEM Compressed 6 1 to 6 4 New System Module released in 6 4 MPC750 CPU 6 1 to 6 4 2M CMEM Compressed MPC750 CPU 6 1 to 6 4
70. ions on the World Wide Web You can define how you use Acrobat with your Web browser 11 2 Keep a Current Set of Manuals Keep a current set of documentation for Release 7 3 RO0A To download a current printed set you will need access to a e Internet connection to the Vanguard Networks product documentation website http www vanguardnetworks com support documentation overview htm e Printer e Copy of Adobe Acrobat for your platform Download manuals from the WWW for the desired features you need Print the files and replace the pages in your set of documentation with the new version Proprietary Page 54 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 12 Vanguide CD ROM with Vanguard Software Builder Vanguide and Vanguide Plus CD ROMs are consolidated into one CD ROM called Vanguide CD ROM with Software Builder Vanguard Software Builder is now included on the Vanguide CD ROM 12 1 Vanguard Software Builder Vanguard Products come with a factory default Applications Ware software image However you can create your own Applications Ware with a specific mix of features by using Vanguard Software Builder This application let s you create custom features sets with features and functions suited for your specific needs The features available for selection depend on the Applications W are License you purchased Vanguard Software Builder operates on Windows XP Windo
71. ller Card Product Code 1112 10037 is now 7 3 If the 7300 V3 System Card is configured with any previous software release the following behavior may be encountered o The date and time will not be updated correctly o Power up Diagnostics will show failures in the two areas shown below both of which are related to the revision changes Testing NVRAM gt gt FAILED lt lt 00 NVRM_ 0000 0000 0000 0000 0000 Testing Real Time Clock gt gt FAILED lt lt 4 5 NULL ROUTES Overview A Null route is a static route that discards packets It is used to engineer networks to prevent the use of the default route when the preferred route is lost In many cases when a preferred dynamic route is lost the default route would cause routing loops if used A Null Route differs from an IP Filter in that it can be installed and removed from the routing table when its metrics are compared to other routes for the same subnet IP filters on the other hand are always in the table In 7 3 RO0A the nexthop IP address for a static route can be configured as 255 255 255 255 This nexthop will drop packets A Null route can be used to backup a route from a dynamic routing protocol to prevent routing loops Behavior The default route is configured as a static route with a nexthop to discard the packet It is configured to be less preferred than the dynamic route protects Vanguard refers to this as a backup static route The Null route behavior differs i
72. n some ways from a backup static route The Null Route is not advertised The Null route is not redistributed into another routing protocol From a dynamic routing protocol point of view RIP RIPv2 OSPF BGP a Null route is considered to be no route That means when a null route is installed in the routing table the dynamic routing protocol will issue a WITHDRAW of the route to its neighbors A Subnet Route which has only a NULL route as a member of its summary range should not be advertised If it has been previously advertised by a dynamic routing protocol it should be withdrawn Configuration Requirements Proprietary Page 14 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 To activate the Null Routes feature Override Static Routes in Configure IP Interface configuration Table must be enabled Then configure Next Hop in Static Routes Configuration as 255 255 255 255 with a bigger number of Metric compared to other routes for the same subnet IP 1 Next Hop 0 0 0 0 Range A valid IP address in dotted notation Default 0 0 0 0 The IP address of the next hop to the destination The next hop itself must be on an IP network directly connected to the router If the next hop is an unnumbered interface enter 0 0 0 N where N is the interface number 1 If next hop is 255 255 255 255 the route is a null route 4 6 IPSec Aggressive Mode Overview When the
73. ndard Applications Ware package 2 5 Memory Requirements for Applications Ware Release 7 3RO0A Proprietary Page 6 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 The total memory required for each product at release 7 3 ROO0A is listed in this table Platform Required Memory Required FLASH Vanguard 3410 3410W 3460 3480 RAM 64MB SDRAM 16MB Flash Vanguard 6840 6841 256MB DRAM 256MB Flash Vanguard 7310 7330 V2 V3 512MB DRAM 64MB Compact Flash Notes e The table above lists the memory that is shipped e Release 7 3 ROOA does not support the Vanguard 100 200 300 305 311 311 S 3127 S 320 340 242D 342 340E 6425 6430 6450 6435 6455 6520 6560 platforms 3 Products Supported Products supported by Release 7 3RO0A Product Support Vanguard 3410 3410W 3460 3480 Normal Product Release Vanguard 6840 6841 Normal Product Release Vanguard 7310 7330 V2 V3 Normal Product Release Release 7 3 ROOA is not supported on these discontinued products Product Last Release Supported Vanguard 100 Maintained at 5 3M Vanguard 200 Maintained at 5 1M Vanguard 300 Maintained at 5 4 Vanguard 305 Maintained at 5 5 Vanguard 311 Maintained at 5 1M Vanguard 31x Maintained at 5 3M Vanguard 320 Maintained at 6 4 R10A Vanguard 6425 6430 6450 Maintained at 6 0 ROOA Vanguard 340 Maintained at 7 0 ROOA Vanguard 6435 6455 Maintained a
74. nge which are outside of any dialog will use the same values for the Call ID and From tag as in the original request and the CSeq number will be one higher than in the original request Enabled If enabled authentication requests sent in response to a challenge which are outside of any dialog will use new values for the Call ID From tag and CSeq number than those used in the original request SIP Signaling DSCP Value 40 Range 0 63 Default 40 Enter the DSCP value for SIP signaling packets SIP RTP DSCP Value 46 Range 0 63 Default 46 Enter the DSCP value for SIP RTP packets On Hold Media Attribute Sendonly Range Sendonly Inactive Default Sendonly Proprietary Page 16 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO00A Part No T0300 Rev B Aug 2010 This parameter specifies the media attribute to use in the SDP when sending an offer to put the remote end on hold Sendonly Specify a sendonly in SDP Inactive Specify a inactive in SDP 4 10 2 Voice Switch Table change in support of SIP E 164 Numbering Additional Voice Switching Features NONE Range NONE H323_USE_ INTERFACE IP_ADDR ENABLE VOICE _MAIL E 164 NUMBER Default NONE Select Additional Voice Switching Features NONE no features enabled H323_ USE INTERFACE ID ADDR Force all outbound H323 calls use the Interface IP address as the Source IP address in H 225 H 245 and media channel connection ENABLE VOICE M
75. ns Ware supports a suite of default features Other features however can be added by using Vanguard Software Builder For more information refer to the Vanguide CD ROM with Vanguard Software Builder section in this document Chapter 12 Notes 1 When using Vanguard Software Builder be sure to make note of the warnings regarding memory limitations 2 Information about the Applications Ware is divided into four tables a The first two tables list each model s Applications Ware and file information b The last two tables list each model s Applications Ware and its default optional and add on features 6840 Applications Ware Name Source Version String Description Filename Filename IPSAFE Applications Ware 73R00Abal1 xrc 7 3 RO0OA_ IPSAFE_6840 73RO0Aba 1 1 des SNA Applications Ware 73RO0Abal2 xre_ 7 3 RO0OA_ SNA _6840 73RO00Aba12 des Multi service Applications Ware 73RO0Abal5 xre_ 7 3 RO0OA_ MS_ 6840 73RO0Aba15 des 6841 Applications Ware Name Source Version String Description Filename Filename IPSAFE Applications Ware 73RO0Abal1 xrc_ 7 3 RO0OA_ IPSAFE_6840 73R00Abal 1 des SNA Applications Ware 73ROO0Abal2 xre_ 7 3 RO0OA_ SNA _6840 73RO00Aba12 des Multi service Applications Ware 73ROOAbal5 xre_ 7 3 RO0OA_ MS_ 6840 73RO00Aba15 des Proprietary Page 61 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Au
76. o reduce security risks in a BGP network The Vanguard implementation of BGP peer authentication uses the TCP MD 5 signature as specified in RFC 2385 This algorithm takes a key the password entered during configuration and performs an MD 5 hash on the key and sends the resulting hash to the remote peer The password itself is never sent over the connection Both sides of an authenticated BGP peer session must use the same password The authentication occurs in the TCP session not on the BGP peer session Proprietary Page 9 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 It provides added confidence that packets received from the TCP peer actually originated from the authorized TCP peer Though first released in patch 7 2P01D the following parameter is new and is now generally available in release 7 3 RO0A This new parameter MD5 Password can be found under configure gt configure router gt configure BGP gt Peer Parameters MD5 Password Range 1 25 alphanumeric characters use the space character to blank field Default blank Description Enter password for TCP MD5 Signature Option A blank password means the feature is turned off 4 3 NHRP Next Hop Resolution Protocol Vanguard Networks Routers now support NHRP Next Hop Resolution Protocol This was introduced in response to the demand for Vanguard Network routers to oper
77. oid network disruptions There is no plan to correct this issue 10 CR18164 Bridging total 1 Vanguard products support bridging of data traffic for Token Ring and Ethernet LANs Bridging LAN traffic minimizes your networking costs by eliminating the need for redundant networks and maximizes the availability of dedicated facilities such as servers and printers as well as public Frame Relay and X 25 services across multiple LANs Note The Vanguard 3480 Switch does not support the Bridging feature 11 CR17762 Problem Description On the VN3480 when two Ethernet Ports 24 through 27 are configured with their Switch Capabilities set to SWITCH_TO_ROUTER_UPLINK and their associated the Router Interface has the same VLAN ID setting and the same subnet IP Address the higher numbered port will have a Port Status of MISCONFIG when the router is Warm Booted Work Around Itis recommended that when more than one VN3480 Ethernet Port 24 through 27 is configured with a Switch Capabilities of SWITCH_TO_ROUTER_UPLINK their associated Router Interfaces should be configured with a unique VLAN ID and with a unique IP Address Valid Configuration Invalid Configuration 24 Switch Capabilities Port 24 SWITCH_TO_ROUTER_UPLINK 24 Switch Capabilities 24 Router Interface Number 2 SWITCH_TO_ROUTER_UPLINK 24 Router Interface Number 2 Port 26 Port 26 26 Switch Capabilities 26 Switch Capabilities SWITCH_TO_ROUTER_UPLI
78. on traffic_monitor_opt mib Traffic Monitor trap mib trap mib v_opt mib Voice Relay option vpmt_opt mib Virtual Port Mapping Table option virp_opt mib Virtual Router Redundancy Protocol wan_opt mib WAN support required file x25_opt mib X 25 option xdlc_opt mib XDLC protocol 17 Applications Ware RFC Compliance RFC Description User Datagram Protocol J Postel Aug 28 1980 Internet Protocol J Postel Sep 01 1981 Internet Control Message Protocol J Postel Sep 01 1981 Not all messages covered by RFC 792 are supported by Applications Ware Transmission Control Protocol J Postel Sep 01 1981 An Ethernet Address Resolution Protocol or Converting network protocol addresses to 48 bit Ethernet Address for Transmission on Ethernet hardware D C Plummer Nov 01 1982 Telnet Protocol Specification J Postel J k Reynolds May 01 1983 Telnet Suppress Go Ahead Option J Postel J K Reynolds May 01 1983 Standard For The Transmission Of IP Datagrams Over Public Data Networks J T Korb Sep 01 1983 Proprietary Page 74 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Standard for the Transmission of IP data grams over Ethernet networks C Hornig Apr 01 1984 Broadcasting Internet Datagrams J C Mogul Oct 01 1984 Broadcasting Internet data
79. owing European Directives e 1999 5 EC Radio amp Telecom Terminal Equipment R amp TTE e 73 23 EEC Low Voltage Directive Safety e 89 336 EEC EMC Directive 19 3 Declarations of Conformity English Declaration of Conformity Hereby Vanguard Networks declares that this Vanguard Router is in compliance with the requirement and other relevant provisions of Directive 1999 5 EC Danish Konformitetserkl rin g Hermed erkl rer Vanguard Networks at indest ende Vanguard Router er i overensstemmelse med de grundl ggende krav og de relevante punkter i direktiv 1999 5 EF Proprietary Page 83 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Dutch Verklaring van overeenstemming Hierbij verklaart Vanguard Networks dat diens Vanguard Router voldoet aan de basisvereisten en andere relevante voorwaarden van EG richtlijn 1999 5 EG Finnish Vaatimustenmukaisuusvakuutus Vanguard Networks vakuuttaa taten etta Vanguard Router on direktiivin 1999 5 EC keskeisten vaatimusten ja sen muiden tata koskevien s nn sten mukainen French D claration de conformit Par la pr sente Vanguard Networks d clare que ce routeur Vanguard est conforme aux conditions essentielles et toute autre modalit pertinente de la Directive 1999 5 CE German Konformit tserkl rung Hiermit erkl rt Vanguard Networks dass der Vanguard Router die grundlegenden Anforderungen und sonst
80. ple of a VN3480 forwarding Authentication and Accounting messages to Server 1 and forwarding Event and Traffic messages to Server 2 Fig 1 Application of Vanguard Networks SYSLOG Client Feature TRUST SYSLOG Server A ZONE Authentication and Accounting Message Msg A Logging i SYSLOG Server B Untrust Event and Traffic Zone Q Message Logging The 3480 sends SYSLOG Messages to Hosts A and B Msg A Authentication and Accounting Type SYSLOG messages Msg B Event and Traffic Type SYSLOG Messages 4 11 2 SYSLOG Configuration The SYSLOG Configuration consists of SYSLOG Global Configuration and SYSLOG Server Configuration The SYSLOG Global Configuration consists of the SYSLOG Global Enable parameter This enables or disables the SYSLOG Client Feature in the router Figure 2 shows the Global Parameters Configuration SYSLOG Global P ters Confi ti SYSLOG Global Enable Range ENABLED DISABLED Default DISABLED Help Text Enable Disable SYSLOG in this router Figure 2 SYSLOG Global Parameters Proprietary Page 19 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Figure 3 shows the SYSLOG Server Configuration parameters The maximum number of SYSLOG Servers that may be configured is two Each Server Connection can be enabled independently via the SYSLOG Connection Enable The SYSLOG Server Protocol supported in Release 7 3 is UDP As shown in Fig
81. r Conversion LLC ETH LLC FR D OO rT rr re UlUOl Trl omneo Proprietary Page 64 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 ASYNC BYPASS ADSPAD SLIP TNPP TNPP ROUT X 42 GSC T3POS T3POS over TCP DATAPAC 3101 PAD 3201 SPP PAD AC100 SHDLC TBOP TBOP BYPASS X32 XDLC BSTD Burroghs Poll Select TCOP TCOP BYPASS NCRBSC RS366 801 Autodialer Protocol TPA TPDU TPA SDLC TPA 3270 TPA 2780 TPA TCP TPA UDP ATCIF AT Dial Telnet LBU DCP DSCOPE DSD NCCP BCST NUI Northern Telecom Backbone TOW QoS Protocol Priority 5 3M Proprietary Page 65 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 QoS Diff Serv Ethernet DiffServ QoS WAN MLPPP LFI FRAME Data Comp IP FLOW o MLPPP NetFlow 5 Security and VPN Enhanced Firewall DOS mitigation Intrazone Interzone Control Plane Policies Syslog Client IPSec 3DES S W based encryption IPSec Aggressive mode SSH Hardware Accelerated Encryption amp VPN DES 3DES and AES PKI amp X 509 Digital Certif
82. r traffic to the router into a separate set it also makes the intent of the configuration much clearer In Configure Firewall Policies the following selections are added Trust gt Control Plane Untrust gt Control Plane and DMZ gt Control Plane 4 12 3 Firewall Intrazone Policies Firewall intrazone policies are used to filter traffic sent between endpoints within the same zone In Configure Firewall Policies the following selections are added Trust gt Trust Untrust gt Untrust and DMZ gt DMZ Node Node3463 Address 3463 Date 24 JUN 2010 Time 13 56 17 Menu Configure Firewall Policies Path Main 6 15 6 2 Trust gt Untrust Untrust gt Trust Trust gt DMZ DMZ gt Trust DMZ gt Untrust Untrust gt DMZ Trust gt Control Plane Untrust gt Control Plane DMZ gt Control Plane Trust gt Trust Untrust gt Untrust DMZ gt DMZ Proprietary Page 23 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 4 13 Denial of Service Dos Mitigation The Firewall now includes support for DoS Mitigation Under Configure Firewall there is a new menu Configure DoS Mitigation Protection against various Denial of Service attacks may be enabled on a per zone basis Menu Configure DoS Mitigation Path Main 6 15 6 3 1 Trust Zone 2 Untrust Zone 3 DMZ Zone Configure DoS Mitigation Trust Zone 1 IP Packet Fragment Protection Disabled
83. reater The new 1 40 or greater boot prom is fully compatible with the original controller card and all software versions that worked with boot prom revision 1 30 If you use an older Vanguide CD to load an older Proprietary Page 45 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 image it attempts to downgrade the boot prom which renders the controller card inoperable and it will have to be replaced In order to prevent inadvertently loading boot prom revision 1 30 onto a new system controller card please discard any CD s previous to the 5 4 POLB CD For more information refer to the Vanguard 7300 Controller Card Hardware Advisory Notice Part Number T0185 04 located on the web at http www vanguardnetworks com support documentation overview htm Also refer to the Boot Prom Software Updates section Chapter 8 of this Software Release Notice Notes The most current boot prom for the MCP750 and IBM750 CPU card is 3 00 Do not use boot prom 2 00 on the MCP750 CPU card The IBM750FX CPU card available with release 6 4 R10A and greater must use Boot prom 2 00 8 7 Controller Card Board Assembly Number Location Refer to the figure below to locate your board assembly number 8 8 Vanguard 7300 CPU Card Upgrade The Vanguard 7300 Series MCP750 part number 75836G02 system cards are supported by software releases 6 1 T14A and greater If you have a part number 75
84. ries 16 000 1 600 7300 Series original size 1 600 Proprietary Page 37 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Additional Limits ATM ATM Stations Maximum FRST Entries SAR Profile X25 Profile Maximum Compressed Data Connections Additional Limits LAN Transparent Bridge Forwarding Table Size 7300 Series original size 8 000 16 000 255 255 Max number of OSPF interfaces 255 255 255 BGP Policy Table 2 048 768 768 BGP Route Table 15000 G1 20000 G2 10000 10000 BGP to OSPF Import Policy Table 1 024 1 024 1 024 BGP Maximum peers 128 16 16 QoS QCL Profiles 1 000 1 000 1 000 QoS IP MF Classifiers 10 000 10 000 10 000 VLAN Sessions 16 per port 50 per node Vanguard 34x 20 per node 50 per node 30 per node 30 per node 50 per node 30 per node 30 per nade Proprietary Page 38 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 8 BOOT PROM SOFTWARE UPDATES This section provides instructions for Cold loading the Boot prom using Software Loader or Procomm Communication software A Caution Backup your configuration Upgrading to a new release could cause configuration loss If you choose to down
85. s Encryption Acc AS400 BSC Advanced Voice SPECIALS SNMP v3 TELNET TFTP CLI Embedded Web HTTPD ATPAD APAD ISDN BRI NOAM ISDN BRI EURO ISDN BRI ASIA ISDN T1 E1 PRI Data NA Default ISDN T1 E1 PRI Data European ISDN T1 E1 PRI Data Asia ISDN T1 E1 PRI Voice incl sign NA ISDN T1 E1 PRI Voice incl sign Euro G 723 1 G 729A CVSELP Centralized Voice Switching Voice Routing Services Half Duplex Radio G 723 1 G729A G711 can t add T 38 Proprietary Page 67 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 G 723 1 G711 can add T 38 G 729AB G711 can add T 38 G 723 1 G729A G711 T 38 but no VAD Centralized Voice Switching Voice Routing Services FAX ITU T 38 Vanguard T1 E1 PRI Digital Voice Server Half Duplex Radio T 38 w G 723 amp G 711 for T1 E1 T 38 w G 729a amp G 711 for T1 E1 Voice Relay with G 723 1 and G 729a Voice Relay Encapsulated in IP SoTCP H 323 v 2 Standards Based Voice SIP SIP Connect 1 0 Caller ID H Call Hold Call Waiting Call Transfer Call Forward 3rd Party Conferencing Router IP D Router IPX D LLC Eth IPXWAN Appletalk Bandwidth on
86. s IP and LAN Feature Protocols SNA Feature Protocols Serial Feature Protocols Multi service Feature Protocols Multimedia Feature Protocols Each of these sets which are available on our website consists of several manuals The contents of each set and the manual part numbers are described below Note For information about obtaining these documents refer to the How to Obtain User Documentation section in this document Chapter 12 10 1 Applications Ware Basic Protocols Manual The Vanguard Applications Ware Basic Protocols Manual Part Number T0106 consists of these manuals Vanguard Configuration Basics Part Number T0113 Frame Relay Part Number T0106 02 Trans Polled Async Part Number T0106 03 SNMP Part Number T0106 04 Async Bypass Part Number T0106 05 SLIP Part Number T0106 06 TELNET Part Number T0106 07 Point to Point PPP amp MLPPP Part Number T0106 08 Command Line Interface Part Number T0106 09 X 25 Configuration Basics Part Number T0107 Configuration for APAD ATPAD Part Number T0110 Bandwidth Management Part Number T0108 10 2 Applications Ware IP and LAN Feature Protocols Manual The IP and LAN Feature Protocols Manual Part Number T0100 consists of these manuals Vanguard Router Basics Part Number T0100 01 Bridging Part Number T0100 02 IP Routing Part Number T0100 03 OSPF Part Number T0100 04 SIP Part Number T0100 05 SoTCP Part Number T0100 06 IPX Part Number T0100 07 AppleTalk
87. sion Table 18100 7 2 P01M Firewall Stats Wrong Firewall Flow Status with permitted fragmented 18103 7 2 R00A PAD port configured for 5 data bits not working supported 18118 7 2R00A BGP is not learning the external networks properly stats do not show AS 18132 7 2P01P Node restarts when stressing dual BGP peers with RIP redistribution Proprietary Page 27 of 84 8 11 2010 Change Problem Description Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 18134 7 2 T02C Fax over G 711 is no longer working 18155 2 BGP is not learning external routes from Backbone properly 18187 SNMP MIB OID support for NHRP not available 18191 IPSec The node stops ISAKMP negotiation 18192 NAT running does not allow BGP load balancing 18208 Unable to ping to the remote nodes tunnel interface over GRE tunnel 18213 VLAN encapsulated packets not utilizing IP Aggregated Cache 18219 e Increase Aggregated Cache for 68xx and 34xx Note The enhancements associated with CR 16670 thru 18155 are also included within the 7 2S 100 Service Pak 6 Known Software Limitations CR17945 For PAD Port Auto Baud Sequence DOT DOIT CH two or three Te are accepted prior to the CR More than three s prior to the CR is no
88. t 7 0 ROOA 6500 Maintained at 5 1M 650D Product maintained at 5 0C Vanguard 6520 Product maintained at 5 5 Vanguard 6560 Product maintained at 6 0 RO0A Vanguard 342 340E Maintained at 7 2 ROOA Vanguard 242D Maintained at 7 2 ROOA Proprietary Page 7 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 4 New Features The new features available for Release 7 3 RO0A are described briefly below Detailed descriptions of the new Release 7 3 ROOA features can be found in the referenced documents Each document can be accessed through the Vanguard Networks Public website at the following url http www vanguardnetworks com support documentation overview htm Instructions for obtaining on line and CD versions of the documents that contain detailed explanations of these features appear in the How to Obtain User Documentation section in this document Chapter 12 4 1 New Hardware Platform 3410W Access Services Gateway The Vanguard 3410W provides a high performance cost effective WAN CPE solution for Internet Access Broadband VPN MPLS Frame Relay or lease line services The 3410W ASG supports optional connectivity to Bisync SNA or Serial transactions devices ATMs bank controllers POS devices etc on today s and tomorrow s carrier transport technologies enabling seamless migration without ripping and replacing non IP applications or peripheral devices T
89. t acceptable and may result in the Auto Baud Sequence to resynchronize and restart its search for the DOT_DOT_CR sequence Workaround The DTE Device connected to the PAD Port must ensure that it transmits two or three e and does not attempt to transmit more than three s prior to the CR CR17916 Invalid RFC1294 encapsulation errors when running an LCON with RTP UDP Header Compression between Releases 6 5R00A and 7 0RO00A or greater Work Around Users must disable RTP UDP Header Compression CR16844 GRE Tunnels may activate ISDN Encryption session keep alive trigger GRE tunnels and ISDN calls even when there is no data to be sent Workaround Increasing the session timeout in the encryption profile will decrease the frequency of the extra ISDN calls CR16941 Only the first 155 entries in the Virtual Port Mapping Table are valid The available range in the VPMT is 1 255 If you use entries above 155 the mapped Voice port will become disabled Workaround Limit configuration to the first 155 VPMT table entries CR17539 BRI Interface remains IDLE after the node is booted If the node is booted while an ISDN call is active the Interface may not recover and continue to pass data Proprietary Page 28 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Workaround After booting the interface Boot Virtual Port Boot If unsuccessful unplug and plug the cable
90. tication string used in NHRP messages If blank authentication is not used NHRP Holding Time Range 0 65535 Default 7200 Description This parameter specifies the holding time value in NHRP registration requests The NHS will cache the registration request for the duration of the holding time value in seconds NHRP Registration Timeout Range 0 65535 Default 2400 Description Registration requests are sent out every this parameter seconds If this parameter is set to 0 then registration requests are sent out every 1 30f holding time seconds Set NHRP Unique Flag Range Yes No Default Yes Description This determines whether to set the unique flag in registration requests If the flag is set the hub will prevent the mapping entry from being overwritten by a registration request with the same protocol address but with a different NBMA address It s recommended to set this parameter to Yes if the tunnel s source address is static to No if dynamic Proprietary Page 12 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Statistics Statistics supporting NHRP can be found from the main menu under through the Statistics gt Router Stats gt Tunnel Stats menu path This is a sample of the menu structure Menu Tunnel Statistics Path Main 5 16 11 1 General T
91. tware Release R7 3RO0A Part No T0300 Rev B Aug 2010 4 10 4 Fax Support Enhancement The new T38_ Override selection is introduced for those customers who choose to take advantage of the bandwidth savings of T 38 fax operation even when running G 711 Previous operation was for the voice port to stay running G 711 coder even if fax data was detected FAX Support Range Disabled Proprietary Enabled T38 T38 Override Default Proprietary This parameter selects whether the FAX data is to be supported Proprietary Detects presence of FAX data If FAX data is detected the voice port will spoof the local FAX machine and transmit the Proprietary FAX data to the remote end as 4800bps or 9600bps data T38 Detects presence of FAX data If FAX data is detected and the current codec is not G 711 the voice port will spoof the local FAX machine and transmit the T 38 standards based FAX data to the remote end T 38 support fax data rates of 14 4kbps 12 0kbps 9 6kbps 7 2kbps 4 8kbps or 2 4kbps If the current codec is G 711 the fax data will be transmitted transparently over G 711 T38 Override Detects presence of FAX data If FAX data is detected regardless of the current codec the voice port will spoof the local FAX machine and transmit the T 38 standards based FAX data to the remote end T 38 support fax data rates of 14 4kbps 12 0kbps 9 6kbps 7 2kbps 4 8kbps or 2 4kbps Disabled FAX data will not be detected Enabled Supported for
92. unnel Statistics 2 Tunnel RTP UDP IP Compression Statistics 3 NHS Statistics 4 NHRP Mapping 5 NHRP Traffic The statistics displayed are described in the following examples NHS Statistics Node vgnhrp Address 100 Date 16 AUG 2000 Time 18 59 13 NHS Statistics NHS Addr Reg Req retry in Reg Repl State Last Reg Repl Tnl 1 172 020 001 001 536 NA 527 Up 16 AUG 2000 18 41 02 NHRP Mapping Node vgnhrpl1 Address 100 Date 16 AUG 2000 Time 18 59 21 NHRP Mapping Iface Proto Addr NBMA Addr Expiry Type Tnl 1 172 20 001 001 172 028 124 001 Never Static NHRP Traffic Node vgnhrpl1 Address 100 Date 16 AUG 2000 Time 18 59 26 NHRP Traffic Sent via Tnl 1 Req Req 536 Err Ind 0 Received via Tnl 1 Reg Reply 527 Err Ind 0 Unsupported 0 4 4 7300 Platform System Card New Revision V3 The 7300 system card IBM750FX has been revised The part number of the 7300 IBM750FX processor card is 76361G01 this can be found on the card itself and also in Node Statistics page 5 sample below System Controller Number of ports 3 Status Installed and functional Assembly 76361G01 V3 Version D Serial Number 160064574 Notes e Previous revision is Revision B 76361 G01 e The latest revision is Revision D 76361G01 Proprietary Page 13 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 The Software revision to support the New Rev D System Contro
93. ure 3 the SYSLOG Server IP Address and UDP Port Number are specified in the SYSLOG Server Configuration The Source IP Address associated with the SYSLOG connection defaults to 0 0 0 0 If it is left at 0 0 0 0 the router automatically assigns the source IP address to the UDP connection The Source UDP Port number is not configurable This is assigned automatically by the Vanguard Networks Router Also shown in figure 3 are the SYSLOG Type and SYSLOG Severity parameters The SYSLOG Type parameter is used to specify which message types are sent across this SYSLOG Server Connection Event Authentication Accounting and or Traffic Monitoring The SYSLOG Severity Parameter serves a filtering function Messages with their severity value specified here are allowed to traverse across this server connection to the attached SYSLOG server Proprietary Page 20 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO00A Part No T0300 Rev B Aug 2010 SYSLOG Server Configuration cont SYSLOG Type Range EVENT TRAFFIC AUTHENTICATION ACCOUNTING Default EVENT TRAFFIC AUTHENTICATION ACCOUNTING Help Text The SYSLOG Type parameter selects the type of SYSLOG messages to forward across this SYSLOG Server connection EVENT Forward Alarm messages TRAFFIC Forward Traffic messages AUTH Forward Authentication messages ACCOUNTING Forward Accounting messages Any combination of above specified by summing e g EVENT TRAFFI
94. vices and Segmentation Enblock Signaling Support only at this time 7 1 Software Configuration Limits The following table lists the software configuration limits for Physical Ports physical port counts are set by software not the actual number of physical ports Frame Relay Sessions Network Services LAN IP specific Voice SNA IBM Support Proprietary Page 34 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Software Configuration 7300 Series 6840 6841 3410 3460 3480 Physical Port Maximum Limits Ethernet ports per node MPC750 CPU Ethernet ports per node IBM750FX CPU Ethernet ports per node 2 3410 3460 5 3480 High speed V 35 serial links per node 3460 3480 4 3410 2 Total LAN ports ETH per node not bridged MPC750 Total LAN ports ETH per node not bridged IBM750FX Devices supported per Ethernet segment Relevant to Bridge operation 259 T1 E1 PRI ports data only per node 3460 3480 2 3410 1 T1 E1 PRI voice only ports per node 0 T3 E3 ATM ports per node Voice circuits per voice server card Number voice calls per node Number shown is E1 max Number voice calls per node Number shown is T1 max Frame Relay Number of DLCIs per FR Port Number of PVCs per FR Annex G station Number of SVCs per FR Annex G station
95. wall_opt mib Firewall Option gsc_opt mib GSC protocol hub_opt mib Ethernet Hub option ibm2260_opt mib IBM2260 protocol ipsec_opt mib IP Security isdn_opt mib ISDN protocol iso3201_opt mib 3201 protocol mx25_opt mib MS 273 protocol ncrbsc_opt mib NCR Binary Synchronous protocol ns_opt mib Network Service required file pad_opt mib PAD protocol pim_opt mib Protocol Independent Multicast ping_opt mib Remote Ping Option Proprietary Page 72 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 Ppp_opt mib Point to Point protocol pppoe_opt mib Point to Point protocol over Ethernet qos_opt mib Quality of Service option QoS Kit includes QoS_CORE QoS_CLSSIFIER and QoS_SCHEDULER qos_pp_opt mib Quality of Service option QoS PP Protocol Priority includes QoS_CCM PACKET_CLASSIFIER and PACKET SCH EDULER radius_opt mib RADIUS tfc1213 mib MIB II for managing TCP IP based internets tfc1231 mib IEEE 802 5 Token Ring MIB tfc1286 mib Definitions of managed objects for bridges fc1315 mib Management Information Base for Frame Relay DTEs fc1398 mib Managed objects for Ethernet type interfaces fc1657a mib BGP4 MIB Converted to SNMP version 1 from the ori ginal rfc1657 mib fel 850av mib OS
96. ws NT Windows 2000 95 or 98 platforms Vanguard Software Builder is part of the Vanguide Application Set This set also includes the Vanguide Application Manager which provides access to the Software Loader and Software Builder applications Once Software Builder is installed you can e Select a specific software release e Choose the product which you are loading configuring e Create a name and 2 digit number for the Applications Ware Package you want to create e Follow a series of command prompts to select features protocols for your Package For more information refer to Vanguard Software Builder Manual Part Number T0030 13 Release 7 3ROO0A for the Vanguard 3410 3410W 3460 3480 Release 7 3 RO0A supports the following Applications Ware for the Vanguard 3410 3410W 3460 and 3480 Each Applications Ware supports a suite of default features Other features however can be added by using Vanguard Software Builder For more information refer to the Vanguide CD ROM with Vanguard Software Builder section in this document Chapter 13 Notes 1 When using Vanguard Software Builder be sure to make note of the warnings regarding memory limitations 2 Information about the Applications Ware is divided into four tables a The first two tables list each model s Applications Ware and file information b The last two tables list each model s Applications Ware and its default optional and add on features 3400 Applications
97. ws a Vanguard 7310 Directory selected C Vanguard SFW_IMGS 7310 COLDLOAD Note Under the SFW_IMGS directory all the Vanguard products are listed To select a Vanguard 7310 the path would be C Vanguard SFW_IMGS 7310 COLDLOAD Proprietary Page 44 of 84 8 11 2010 Vanguard Networks Applications Ware Software Release R7 3RO0A Part No T0300 Rev B Aug 2010 C Vanguard J SFW_IMGS E 7310 E COLDLOAD C Yanguard SFW _IMGS 7310 COLDLOAD Ex J File Edit view Favorites Tools Help l Back H Q Search PyFolders history R GS X Kai es Address E C Vanguard sFw IMGS 7310 COLDLOAD Ze Folders Sie Type Modified vanguard S CI 7T108P 110 File Folder 2 27 2002 9 00 AM BACKUP TIOBP 111 File Folder 2 27 2002 9 00 AM HC CONFIGS COLDLOAD T10bp130 File Folder 2 27 2002 9 00 AM DOCS T10BP140 File Folder 2 27 2002 9 00 AM 8 PATCH Select an item to view its description T1OBP 150 File Folder 2 27 2002 9 00 AM a SFW In Baan EE XRC File 2 23 2002 1 53 AM GR 6435 eee a c7Bay 192 xre XRC File 2 23 2002 1 55 AM GR 6455 eege a c73av288 xrc XRC File 2 23 2002 1 54 AM E 680 gee a e73yv384 xre XRCFie 2 23 2002 1 54 AM i Ge ee a c73av576 xrc XRC File 2 23 2002 1 54 AM Ss Ge a c73av96 oC XRC File 2 23 2002 1 55 AM d a 7310 a c73cv115 xre XRC File 2 23 2002 1 53 AM E COLDLOAD a c7Scv192 xrc XRC File 2 23 2002 1 55 AM Cy tioo O a c73cv288 xre XRC File 2 23 2002 1 54 AM 2 T106P1

7.3 Software Release Notice

Contents

Download Pdf Manuals

Related Search

Related Contents