3D Hero® SyStem
Contents
1. on the camera to UPd mode upside down allowing for synchronized sync cable attaches to the right camera while side that 3D video and photo capture says L on the sync cable attaches to the left camera Note Upon insertion of the sync cable the right REMOVING 3D SYNC CABLE FROM CAMERAS camera will automatically set itself to be in UP mode and the left camera will automatically set itself to To remove the sync cable from the HD HERO Bus Port grasp be in UPd mode This configuration is required for each 3D sync port connector firmly and remove by lifting device evenly away from the HERO Bus Port Do NOT pull on capturing synchronized 3D videos and photos If 3D synchronization is not desired you can manually change each camera s settings to be ina different UP UPd mode different resolution etc but the cameras will only record in a synchronized manner allowing for 3D if BOTH cameras are set to shoot the same resolution record mode and frame rate cable connecting the left and right HERO port connectors USING THE 3D HERO SYSTEM IMPORTANT To capture 3D video and photos both cameras must be set to identical resolution record mode and frame rate settings To begin recording video or photos 1 Power on both cameras 2 Verify that SD cards are present in both cameras that batteries are charged and that both cameras are set to the same resolution record mode and frame rate Upon insertion of the sync cable righ2. 3D sync cable Do not use the 3D HERO System if it has been damaged AVOIDING WATER AND WET ENVIRONMENTS WHEN NOT IN WATER HOUSING Do not use the 3D sync cable in rain near wash basins or in other wet locations when cameras are not inserted in the water housing Do not spill any food or liquid on the 3D sync cable If the 3D sync cable gets wet unplug from camera and allow it to dry thoroughly before using again Do not attempt to dry the 3D sync cable with an external heat source such as microwave oven or hair dryer Damage to the 3D sync cable caused by contact with liquid is not covered under warranty USING CONNECTORS AND PORTS Never force a connector into a port Check for obstructions in the port Make sure that the connector matches the port and that you have positioned the connector correctly in relation to the port 11 WARRANTY This product is guaranteed against manufacturing defects for one 1 year from the original date of purchase GoPro s sole obligation in the event of such defects during this period is to repair or replace the defective part or product with a comparable part or product at GoPro s sole discretion Except for such replacement the sale or other handling of this product is without warranty condition or other liability even though the defect or loss is caused by negligence or other fault Damage resulting from use accident or normal wear and tear is not covered by this or any warranty GoPro
3. assumes no liability for any accident injury death loss or other claim related to or resulting from the use of this product In no event shall GoPro be liable for incidental or consequential damages relating to or resulting from the use of this product or any of its parts Because of possible user resealing error this product is not warranted against waterhousing leakage or any resulting damage Visit gopro com for more information 12
4. using two quick release buckles More stable video with dual quick release buckles LJ Less stable video with single quick release buckle CURVED AND FLAT SURFACE MOUNTING oe 100 BOO dim The extension arms and quick release buckles be used in a number of different orientations depending on what type of surface you are attaching the 3D HERO System to For example attach included extension arms to the quick release buckles in order to achieve proper orientation when attaching the waterhousing to curved surfaces Note When removing the quick release buckles from the adhesive mounts push both quick release buckles out evenly to avoid jamming the buckles 8 FRONT HELMET AND CHEST MOUNTING Attach t the cent SSE 00 elmet Mount he Front Helmet Mount to the center fingers with mount adapter and long thumb screw Chest Mount Attach t he curved quick release buckle and straight arms if necessary for proper angle adjustment to the center fingers on the waterhousing with the center mount adapter and long thumb screw WARNING Single center mou
5. 3D HERO SYSTEM USER MANUAL WARRANTY INFO Bea FIRMWARE UPDATE The 3D HERO System requires two 1080p HD HERO cameras You will need to make sure both of your HD HERO cameras have the latest firmware installed before using the 3D HERO System To download the latest firmware visit gopro com firmware REQUIRED FREE 3D EDITING SOFTWARE GOPRO CINEFORM STUDIO Your 3D HERO System allows you to combine two 1080p HD HERO cameras with a 3D HERO Sync Cable to record synchronized videos and photos The cameras record video and photos much like your eyes see the world with right and left lenses While recording each camera independently saves 2D video or photos to the respective SD card In order to convert the saved 2D files into a single 3D file you will need to download a FREE copy of GoPro CineForm Studio from gopro com 3D GoPro CineForm Studio makes creating 3D videos and photos easy Simply import the video or photo files you want to convert to 3D click a button and the software automatically converts your paired 2D files into a single viewable 3D file Using the red blue anaglyph glasses included with the 3D HERO System you can watch your 3D videos and photos on your computer online at video sharing sites like YouTube that support 3D videos or on your 3D TV at home using active or passive shutter glasses depending on your 3D TV To download and install your free copy of Go
6. Pro CineForm Studio visit gopro com 3D 3D HERO SYSTEM FEATURES 1 Master Shutter Button 3 Left Camera Power Button 5 Mounting Fingers 8 Requires Two 1080p Controls Both Cameras HD HERO Cameras 4 Center Mount Adapter 6 3D HERO Sync Cable not included 2 Right Camera Power Button 7 Waterproof Housing ASSEMBLING 3D HERO SYSTEM COMBINING TWO CAMERAS FOR 3D VIDEO AND PHOTO CAPTURE NOTE The 3D HERO System requires two 1080p HD HERO cameras Each camera requires a fully charged battery and SD card with sufficient memory for recording GoPro recommends Class 4 or faster SD cards Each camera s settings e g resolution exposure record mode video format PAL amp NTSC must match for 3D synchronization to work To combine cameras in 3D HERO System waterproof housing 5 Make sure the 3D Sync Cable is fully inserted and is flush against the back of the cameras 1 Open back door to the 3D housing Close waterhousing 2 Insert right camera fight side p into housing If settings are changed and you wish to return each camera to its default 3D setting simply unplug the sync cable and 3 Insert left camera upside down into housing then plug the sync cable back in to both cameras This will 4 Insert the 3D HERO Sync Cable into the HERO Bus reset the right camera to UP mode right side up and the left Port on both cameras The side that says R
7. nt configuration is not recommended for high impact or high vibration use VIDEO RECORDING TIPS For best results keep your subject at least 3 feet away Both lenses should be cleaned prior to and during use from camera when shooting in photo mode 720p and 960p Discrepancies in images between cameras due to dust resolutions When shooting in 1080p because of its less particles water drops etc will cause eye strain when wide angle perspective it s best to keep your subject at viewing in 3D least 5 feet away from the camera Failure to do so will result in an inability to properly align the two video files for 3D and will cause your eyes to strain when viewing the subject on screen The 3D HERO System can record different video resolutions simultaneously but it will not be possible to create 3D video files from the resulting video files as the resolutions will not match Additionally synchronization will not occur when the WARNING If images are shot closer than the resolutions of each camera do not match recommended distances the resulting 3D image will cause eye strain when viewing during playback prevent fogging when using the waterproof back door use GoPro s anti fog inserts with your 3D HERO For best 3D results the right camera must be in UP and System housing the left camera must be in UPd recording modes For convenience the sync cable automatically adjusts each camera into the ideal UP UPd m
8. ode each time you plug the sync cable into each camera TRANSFERRING VIDEO AND PHOTOS TO YOUR COMPUTER Plug the camera into your computer with the included USB cable turn the camera locate the Removable Disk SD Card icon Once the icon is located 1 Double click the Removable Disk icon 2 Double click the DCIM folder icon 3 Image files captured with the right camera will be stored in a folder named 100G_3D_R 4 Image files captured with the left camera will be stored in a folder named 100G_3D_L 5 Any file created during 3D sync recording will start with 3D_L0001 or 3D_R0001 10 CREATING 3D VIDEO AND PHOTOS WITH GOPRO CINEFORM STUDIO To convert 2D video and photo files into 3D files you will need to use GoPro CineForm Studio software GoPro CineForm Studio and associated instructions are available as a FREE download from gopro com 3D IMPORTANT SAFETY HANDLING INFORMATION WARNINGS Failure to follow these safety instructions could result in fire electric shock or other injury or damage to the 3D HERO System or other property Improper alignment of your 3D images or misuse of the GoPro CineForm Studio software while viewing with 3D glasses may cause eye strain or headaches HANDLING The 3D HERO System contains sensitive components Do not drop disassemble open crush bend deform puncture shred microwave incinerate paint or insert foreign objects into the cameras or
9. t camera will automatically set itself to UP and left camera will automatically set itself to UPd This is necessary for capturing synchronized 3D video and photos 3 Press master shutter button on top of 3D HERO System housing to initiate synchronized 3D video or photo capture Additional Notes Blinking front LCD screen and red LED record lights may or may not blink in sync This is OK and has no effect on whether or not each camera is in sync with the other Should the battery die or SD card become full on either camera both cameras will save the files and stop recording Always use brand name SD cards with a Class 4 rating or higher The 3D HERO System can also capture 3D photos time lapse mode every 2 5 10 30 or 60 seconds Photo every 1 second mode is not possible when capturing 3D photos To capture 3D photos in 3D time lapse mode change the mode on both cameras to Photo Every X mode and press the shutter button to begin recording MOUNTING CONFIGURATIONS IMPORTANT It is recommended to use dual quick release buckles for mounting the 3D HERO System whenever possible for maximum stability Using a single center mounted quick release buckle is only recommended for chest helmet suction cup and other body worn applications where high vibration or impact are less likely Use of a single center quick release buckle in high vibration or high impact scenarios can result in less stable video compared to
Download Pdf Manuals
Related Search