OASiS user manual
Contents
1. A panic alarm can be triggered as follows e On the keypad enter 7 before entering an access code before presenting a card If the system has been in a set state it will be unset operation under duress e On the key fob controller press both and buttons simultaneously If desired the controller can be re configured by an installer for Panic Mode in which pressing any button will trigger the Panic alarm e By pressing a large sized panic button that can be installed on a wall under a desk etc e By a panic code or card on the keypad 8 Controlling connected devices from a keypad The control panel allows you to control various devices in the building e g heating air conditioners 13 and a14 Control can be performed via a keypad by keying in the following Oasis user manual 8 MKE22102 Device X m13 turn ON 81 turn OFF 80 Device Y m14 turn ON 91 turn OFF 90 The outputs may be used to unlock locks opening a door via a short impulse In this case enter the following an impulse to operate a13 is provided by pressing 8 an impulse to operate a14 is provided by pressing 9 Optionally the system can be pre programmed by a service company so that the above operations require an access code card 9 Remote control by phone Internet If the control panel is equipped with a suitable communicator C you can control it remotely by mobile phone directl2. factory default 8080 or to enter maintenance mode 0 MC factory default 1234 1 The functions allow the system to be operated from a mobile phone keypad if the control panel is equipped with the relevant communicator Limited warranty Subject to the conditions of this Limited warranty Jablotron Ltd warrants this product to be free from defects in design material and workmanship at the time of its original purchase by a customer for a subsequent period of two 2 years Should your Product need warranty service please return it to the dealer from whom it was purchased 2 3 4 Conditions The warranty is valid only if the original receipt issued to the original purchaser by the dealer specifying the date of purchase is presented with the Product to be repaired or replaced Jablotron reserves the right to refuse warranty service if this information has been removed or changed This warranty does not cover any failure of the Product due to misuse including but not limited to use in other than the normal and customary manner in accordance with instructions for use and maintenance of the Product Nor does this warranty cover any failure of the product due to accident modification adjustment improper repair or acts of God This warranty does not apply to batteries nor modules of other suppliers e g SIM card of the GSM provider The warranty provided does not affect the consumer s statutory rights under applicable
3. movement in a protected area information is sent depending on the system configuration to your mobile phone or to an alarm receiving central monitoring company which performs on site physical intervention Outdoor sirens let the neighbourhood know that something is going on whereas the main purpose of indoor sirens is to discourage the intruder Oasis user manual 2 MKE22102 The Oasis system is configurable and its exact behaviour is determined by system settings The following text contains references to the system configuration table which is to be found at the end of this manual The table should be filled in by an installer during the installation process References are numbered like for instance M 4 In this case you can find particular settings for the 4th parameter in the table System access codes cards The system status can be controlled via a keypad internal or external using access codes or cards To prevent misuse by a stolen card you can set that card access must be confirmed by entering a proper code 5 In addition you can operate the system wirelessly by key fob or remotely via phone or using internet access see www GSMLink cz Access codes and cards Access codes and cards allow system operation i e setting arming unsetting disarming stopping triggered alarms triggering silent alarms PANIC etc Access code functionality can be configured during installation The system allows for u
4. taking the system over from an installer This prevents other parties from accessing the system configuration Master code programming is only possible when the system is unset disarmed and not in maintenance mode To change an existing master code enter 5 XXXX yyyy yyyy where xxxXx is the existing master code yyyy is the new master code the new code must be entered twice to avoid errors Combination 0000 cannot be used The master code cannot be erased Example Existing code 1234 will change to 6723 by entering 5 1234 6723 6723 If you wish to use an access card instead of a code you can enter 5 xxxx and then present the card This makes the card authorized for system configuration If you forget the master code or if you lose the card an installer can reset the code to the factory default setting 1234 this requires the system to be unset disarmed All other pre programmed codes cards in the system remain unaffected 11 Programming user codes cards The system allows for up to 50 different access codes cards Their modification or deletion is only available to the system administrator who knows the master code The most comfortable way to edit the user code is via Olink software Code programming is only possible when the system is unset disarmed and not in maintenance mode In practice it is convenient that each user has his own user code pre programmed The system stores to its memory which c
5. to as a bypass To set up a bypass 1 Press key 1 to open the bypass menu while in maintenance mode 2 Using the amp and W keys you can scroll through all potential alarm sources Select the source detector controller which you want to bypass and a press key 2 to bypass the source for the next setting unsetting cycle the A indicator will start flashing b press key 3 to bypass the source permanently the indicator will light continuously c Multiple pressing and holding of the keys 2 or 3 will toggle the bypass on off on d Using key 4 will cancel all device bypasses in the system 3 All the desired bypasses can be reprogrammed by repeating step 2 4 Press the key to exit the bypass menu Pressing again exits maintenance mode e Ifa system with bypassed devices is being set then bypass text will be displayed on the keypad unit e Any bypass programmed for a single setting unsetting cycle will be automatically cancelled after unsetting disarming the system e The existing bypass configuration can be checked or modified in the bypass menu e If the installer enters service mode all bypasses will be cancelled Alternatively you can cancel all bypasses using key 4 in the bypass menu 17 Setting the internal clock The control panel has a built in real time clock which is used to time stamp all recorded events in the control panel memory The clock should be set during installation Howeve
6. If the control panel is in the requested setting unsetting state before the scheduled event time the event will not change the setting unsetting If any automatic event is selected it will be performed everyday at the programmed time with all its consequences It means that the system will be set even when people are still on the premises To cancel a scheduled event enter 64 n 0 As a factory default all automatic events are switched off 19 Programming phone numbers for SMS messages This setting is usually performed by an installer during the installation The programming of the phone numbers can be also done by the administrator in Maintenance mode if enabled a B Follow the manual supplied with the communicator Oasis user manual 16 MKE22102 Table of user codes Posi ABC Code Card Code holder Posit ABC Code Card Code holder tion ion 1 26 2 Dh 3 28 4 29 5 30 6 31 7 32 8 33 9 34 10 35 11 36 12 37 13 38 14 39 15 40 16 41 17 42 18 43 19 44 20 45 21 46 22 47 23 48 24 49 25 50 Guidelines for filling in the table e Use the ABC column for marking the sections accessible in a split system e Use the Code column to indicate that a position is occupied by a code Use the Card column to indicate that a position is occupied by a card e Use the Code holder column
7. Oasis So much more than a wireless alarm system UAIN faa relator OASIS Y JABLOTRON 4 T y z Ve a al ia JABLOTRON Flashing alarm Constantly lit fault Section A is set e g garage Section B is set e g ground floor Section C is set e g 1st floor Power constantly lit OK flashing backup battery in operation Status or event JABLOTRON Partial setting function sequen ces Display details Programming sequences beginning with the ke 1 2 3 4 5 6 7 8 9 0 sets the entire system the same as the ABC key sets section A the same as the A key sets A and B or just B the same as the B key event memory recall key 4 scrolls backwards the control panel records the 255 latest events new Master Code Card 5 MC NC NC MC master code NC new code access code card programming 6 MC nn NC MC master code NC new code for operation while under duress should be entered before the access code to secretly signal distress PGX control ON OFF 81 80 or enter 8 to trigger if a pulsed switching reaction is programmed PGY control ON OFF 91 90 or enter 9 to trigger if a pulsed switching reaction is programmed To enter Service Mode 0 SC
8. der any circumstances he will not be able to modify or add user codes Unsetting the system by the service code can only be enabled with the written agreement of the owner of the system see M 15 1 System setting arming There are several ways to set arm the system An unsplit system z1 e Enter a code present a card e On the key fob press the button e If operation without an access code is enabled m4 you can set arm the system by pressing the ABC key A system with partial setting arming 22 e If operation without an access code is enabled m4 you only have to press the A button to set section A the B button to set both sections A and B or the ABC button to set the entire system e When the system is only partially set e g only section A it is possible to extend the proportion of the system armed by pressing the corresponding button B or ABC All detectors configured to delayed or next delayed reactions will provide an exit delay Thus you will not need to turn off partial setting first to set the whole system each time you leave the house Instead you can perform total setting straight away and the system allows departure through all zones covered by delayed and next delayed detectors e If operation without an access code is disabled m4 then pressing the A B or ABC key must always be followed by entering an access code or by presenting an access card e Key fob press for total s
9. es 10 12 Key fobsetting noce nl bcedvend adenine len re rii seas eee cones 12 User configuration Maintenance mod e csccssscssssssssssscescecsesesceescees 12 13 Entering Maintenance Mode eee eeeeeeeeeeeeeeeeeeeeseeeseenseeaees 12 14 System TESTING eos esces abeecadonieeadsbisgieidiehicens E E ei EE levine sabi 12 15 Displaying which user card positions are occupied 0 0 eee 13 16 BY PAS Sip eiee enep neie a e n canvas 14 17 Setting the internal clock 00 eee eee eee eeeeeeeeeeeeeseeesecnseesaeeaeeneeeaes 14 18 Automatic setting unsetting schedule 0 0 0 eee eeeeeeeeeeeeeeeeees 15 19 Programming phone numbers for SMS messages eee 16 Your Installer Date Manufacturer JABLOTRON ALARMS Inc http www jablotron com Oasis user manual 1 MKE22102 Dear Oasis user The development and production of your security system have been done by the manufacturer with maximum care so that your oasis of safety your room house or company premises can be protected as well as possible The second party having an impact on the quality of a security system is the installer The installer company should know the system well therefore do not hesitate to contact them if you have any questions about system operation or when you need an in depth explanation of how the system works However the most important participant of a properly working security system is you the daily user Please follow these gu
10. etting A B C press to set section A press O to set sections A B Oasis user manual 4 MKE22102 A split system z3 e If operation without an access code is enabled 4 you only have to press the A or B button to set arm the corresponding section Pressing the ABC button results in total setting e If operation without an access code is disabled m4 and you perform setting arming via an access code or card then only the section assigned to the code card is set A B or ABC If the code card belongs to the whole system ABC then it is possible to set only section A or B by pressing button A or B before entering the code card e Using an access code card assigned to section C will set the entire system ABC You can also set either section A or B alone by pressing the A or B button respectively before you enter a code or present a card e By pressing the button on the key fob the section to which the key fob belongs will be set e When both sections A and B are set the common section C is set automatically too 2 During the setting arming process The system will warn you when anything is going wrong Pay attention at the moment of setting to the information on the keypad If the a10 parameter is enabled then by displaying Triggered det on the keypad the system gives you notice that a detector is triggered usually a window or a door is open By pressing the key you wi
11. exit delay will begin The keypad displays Exit delay The keypad indicates which sections have been set A B C If exit delay acoustic signalling 6 is enabled the exit delay is indicated by regular beeps from the keypad the beeps get faster in the last 5 seconds For a partially set system the exit delay may not be signalled acoustically 7 You have to leave protected areas before the exit delay 420 elapses If final door detector mode 12 is triggered during an exit delay then the exit delay is extended to the moment when the final door is closed So you can set and leave the house comfortably without any haste If the final door detector is not triggered then the system provides a normal exit delay 4 System unsetting disarming After you step into a set armed section an entrance delay will begin This is indicated by displaying Entrance delay on the keypad Also the keypad starts to beep fast if entrance delay acoustic signalling is enabled a8 the wireless keypad only if it is powered from the AC adaptor or the door detector is connected to the keypad or when you open its cover Additionally the entrance delay time can be indicated by an indoor siren During the entrance delay m 21 you have to unset disarm the system by entering a valid access code or alternatively presenting a valid access card or using a valid key fob If final door detector mode m12 is active and you came in thr
12. he second column indicates that the corresponding function is enabled LA B m 1 m 2 M 3 Unsplit syst em Partial setting arming Split system Only allows you to set the Setting arming Aor ABorthe Setting A or B Section Cis entire system entire system automatically set if A B are set Oasis user manual 18 MKE22102 Table of device positions Positi ABC Type Location User Positi ABC Type Location User on on 1 26 2 27 3 28 4 29 5 30 6 31 7 32 8 33 9 34 10 35 11 36 12 37 13 38 14 39 15 40 16 41 17 42 18 43 19 44 20 45 21 46 22 47 23 48 24 49 25 50 Guidelines for filling in the table Oasis user manual The table should be filled in by a service technician according to the system configuration composition Use the ABC column to indicate which section a device falls into Use the Type column for device type specification e g JA 83P JA 83M RC 86 Use the Location User column to describe where a detector is located a porch living room or to write down the user of a remote controller Uncle Charles Aunt Mary The table can be also printed out in the Olink software MKE22102
13. idelines as well as the installer s instructions when you take over the system During the system s everyday use you can read information from the keypad display This way you can be informed that a balcony door is open or that maintenance of a particular device is needed What is a security system Any electronic security system ESS has a control panel as its essential part The control panel comprises all the system s important functions Among the control panel s constituent optional parts there is a communicator for transmitting messages to an alarm receiving centre and a back up battery which ensures that the system works properly for a given period after a power supply outage The control panel should be installed in a hidden place In the case of an intrusion a hidden working control panel transmits messages even if all other parts of the ESS have been destroyed The connection between you and the control panel is established via a keypad This way you can operate the system or conversely the system informs you via the keypad display or LED signalling House premises are protected by detectors These react to various events movement PIR door or window opening magnetic detector glass pane breaks glass break detector In addition smoke detection or combustible gas leak detection can be included in a system s functionality This way an ESS can detect threats to property or health When a security system detects
14. ll be shown which particular detector it is If there are more detectors triggered you can access them on the display by pressing repetitively Naturally in such situation it is appropriate to check through the building and close the doors and or windows If the a10 parameter is disabled then no Triggered det text will be displayed Nonetheless pressing the key lets you display the list of triggered detectors If the w11 parameter is enabled and Triggered det is shown on the keypad display then after entering an access code card or after pressing the A B or ABC button for quick setting arming you will be offered the possibility of a bypass which means the temporary removal of triggered zones from the system If you wish to accept confirm the bypass suggestion press If no confirmation is made the system will not be set The system behaves the same way when bypassing has been pre programmed in maintenance mode Oasis user manual 5 MKE22102 If the 11 parameter is disabled any triggered detector is bypassed automatically no key press confirmation is needed While setting arming the system via a key fob controller any triggered zone is bypassed automatically regardless of the w11 parameter If a detector has been bypassed it starts to protect as soon as it is de triggered for example if a door is closed 3 After the system has just been set armed The keypad beeps and an
15. n The memory entry for the last alarm can be displayed by pressing 4 to scroll through the history keep pressing button 4 Keep in mind that there could be somebody hidden on the premises If you have any doubts then it is recommended to have the premises checked by a security service from the alarm receiving station Oasis user manual 7 MKE22102 6 Operating the system from an outdoor keypad If the system is equipped with a JA 80H outdoor keypad or a JA 80N external card reader then the outdoor device can be set to work the same way as an indoor keypad The system will be set unset after entering a code presenting a card A more common usage of the outdoor keypad is to open the entrance door e Performing setting or unsetting the system is only possible via an indoor keypad or via a key fob controller e Enter a valid access code or present a valid card to the outdoor keypad to open the electronic door lock If the system is set and the door is opened via an outdoor keypad an entrance delay will begin During this delay period the system has to be unset using an indoor keypad unit or a key fob 7 Panic alarm If you are in danger you can trigger a silent panic alarm to inconspicuously call for help After triggering a panic alarm the system will send voice messages SMS messages and pass data to an alarm receiving centre central monitoring station depending on installation settings A set system will be unset
16. national legislation in force nor the consumer s rights against the dealer arising from their sales purchase contract Contents Dear Oasis USEF sscsessssrsesssssssssssssssesessessessssessesessessassssessessssessassssessessnsesees 2 What is a Security system ccicciccsccsssssassessssossscosessessecesssssssesessensasescesonsasssessesses 2 System access codes cards ssccssscssssscssccssssssssccsssessssscsssessssscsssesssssssssessssses 3 1 System Setting ArMING scesecesnesessessesssescetsoneecntesnensesbessnsnsntenssees 4 2 During the setting arming process 2 0 ee ee eee eee cseeeseeeeeeeeeeeeeeneees 5 3 After the system has just been set armed 20 0 0 eee eee eeeeeeeeeeeeeeees 6 4 System unsetting disarming 0 0 0 eee cee ceeceeeeeeeeeeeeeeeeeeeeeeeseeeaeeaees 6 5 LoSstop the alanis vives ses o5e c Sates aiesteen wich Spee ee ae Ge aes 7 6 Operating the system from an outdoor keypad eee eeeeeeeee entrees 8 Te RAMA ALAN ec cec erie ce beats sUs gon Sobed seh ee rae e e iea 8 8 Controlling connected devices from a keypad eee ee eeeeeeeeeeeeeees 8 9 Remote control by phone Internet eee cee creeereeeeeeeeeeeeeees 9 User configuration access codes Cards scecscecscecssccsscssscssscssscsesessseeees 9 10 Programming the master code Card eee eee ese eseeeeeeeeeeeeeeeeeees 10 11 Programming user codes Cards eesscesscesecesecseeeseeeseeeeeeeeeeeeee
17. ode was used for what Oasis user manual 10 MKE22102 event and when As a factory default all access codes cards are blank To define a user code enter the following sequence 6 XxXxx nn yyyy where xxxx is the master code nn is the user code index from 01 to 50 yyyy is the new user code By inserting 0000 the code in the nn position will be erased Example If the master code is 1234 and user 3 s new code should be 5277 enter 6 1234 03 5277 Alternatively assign a card to user 3 by entering 6 1234 03 and present user 3 s card Notes e Botha code and a card can be assigned to every position e Ifyou want to assign a code and a card to position nn set the code and then on the same position the card or vice versa e If the system is programmed to require card verification by code a5 a user who has a code and card set always uses both no matter which order If the user has only a code or a card then verification does not concern him e Ifthe administrator records the codes on the table in the appendix of this manual it is necessary to keep it hidden in a safe place Better would be to use and store them in the Olink software access is encrypted e The installer sets the reaction of the system to each code and the code assignments to each section A B C e A code cannot be assigned to 2 different positions Code relocation can be done by deleting the code card and subsequently programming it to a new p
18. osition e For security reasons do not use codes which are easily predictable such as four equal digits birth dates company personal numbers etc e The administrator can check which positions 01 to 50 are occupied by a code or card in maintenance mode see 15 e To erase a code without knowing its nn position use sequence 6 master code card 00 code e To erase all codes and cards set 6 master code card 00 0000 The master code card will not be effected Oasis user manual 11 MKE22102 12 Key fob setting Setting or adding other key fobs to the system can be done by the installer who is also able to block or replace a lost key fob An immediate bypass can be done by the administrator of the system see 16 User configuration Maintenance mode The following description is intended for a system administrator who knows the control panel master code or possesses a master card which is authorized to modify the system configuration All the settings can be performed via keying in on a system keypad An unfinished sequence can be escaped from by pressing the key A sequence is stored into control panel memory only after the sequence has been completely entered 13 Entering Maintenance Mode You can enter maintenance mode when the control panel is unset by keying in 0 master code card The mode will be indicated on the keypad display Maintenance mode enables the following e internal clock configuration au
19. ough the corresponding door then the entrance delay would be six times longer than if it had been triggered by an ordinary detector i e if you Oasis user manual 6 MKE22102 had come in through a main door This way you have enough time for unsetting the system m 22 However if any other delayed detector is activated the entrance delay will be shortened to a normal entrance delay time e Ifthe is flashing on the keypad and the display is showing which device was triggered it means that there was an alarm Unset the system and carefully check the reason for the alarm Keep in mind that there could be somebody hidden on the premises Alarm memory flashing A can be erased from the display by pressing button An unsplit system a1 e Enter a code present a card e Use a key fob by pressing the or button you will unset the whole system A system with partial setting arming a2 e Enter a code present a card e Use a key fob By pressing the or button you will unset the whole system A split system z3 e Enter a code present a card or use a key fob to unset the corresponding system section 5 To stop the alarm If there is an alarm in the system it can be stopped by entering a code presenting a card or using a on the key fob Alarm signalling a flashing A and information about the reason for the alarm this can be terminated after stopping the alarm by pressing the butto
20. p to 50 different access codes cards to be assigned to different users This way it is possible to distinguish at the alarm receiving centre or in the control panel memory who has operated the device and when As a factory default all access codes are blank It is up to you the system administrator master to define access codes as desired using a Master code or card Note Entering an invalid access code ten times in a row will trigger a tamper alarm The Master code card The master code card is an access code or card with a higher priority which in addition to allowing system control enables you to change or configure access codes for other users Knowing the master code or possessing a master access card is necessary for any user configuration of the system Usually the master code is used by the system owner or administrator who performs a change of the factory default value 1234 to his or her required master code after taking the system over from the installer An access card can be set up in place of a master access code This should be kept in a safe place Oasis user manual 3 MKE22102 The service code The service code is a special code designed for a service company The code allows maintenance technicians system configuration and testing Note it can be set by a service technician that by means of a service code it is possible to unset the system to provide full service and maintenance of the system un
21. r the administrator can re set the clock This can be used Oasis user manual 14 MKE22102 for summer time offsets when automatic summer time is disabled m A To set the clock enter 4 hhmm DD MM YY where hh hours mm minutes DD day MM month YY year Example at 21 30 on April 29 2007 enter 4 21 30 29 04 07 If automatic summer time is enabled m A the control panel s internal clock is automatically offset by 1 hour on March 31st at midnight The offset is then removed on October 31st at midnight to return to winter time 18 Automatic setting unsetting schedule This can be used to program an automatic sequence of daily setting unsetting events Up to 10 daily events can be programmed The events will occur every day of the week To program an automatic schedule enter 64nahhmm where n is the event number from 0 to 9 a is the type of event from 0 to 6 see the following table hh hours time of event mm minutes time of event 1 m 2 x 3 Unsplit system Partially split Split system system No event No event No event Set all Set all Set all Unset all Unset all Unset all Set all Set A Set A Set all Set AB Set B Unset all Unset all Unset A Unset all Unset all Unset B Oasis user manual 15 MKE22102 Example To program setting arming the AB section of a partially split system at 22 45 everyday enter 64 0 4 22 45 To cancel the schedule enter 64 00 Notes
22. t is highly recommended to ask your installer to replace the battery Improper handling can result in damaging the device and loss of warranty Recommendations the system should be annually inspected by a professional installer who should check the backup battery voltage and perform functionality testing 15 Displaying which user card positions are occupied When in maintenance mode the control panel can display which positions in the range 01 to 50 are occupied by codes or cards To display the positions e Press key 5 the display indicates Codes 01 Code or the name of the code holder e Using the arrow keys 4 and W all user positions 01 to 50 can be scrolled through The A indicator shows whether a code is programmed or not and the B indicator shows whether a card is programmed or not This means if both indicators are lit the position is occupied by a code and a card e To exit this code card display mode press the key Notes Oasis user manual 13 MKE22102 e Code programming is only possible when the system is unset disarmed and in Operating mode When the system is in Maintenance mode code programming is disabled e The most convenient way to administer codes is by using a PC running Olink software select the Codes menu option 16 Bypassing In practice you may need to set arm the system while excluding particular zones potential sources of alarms This exclusion is referred
23. to write down the name of the person who is authorized to use the code e Use positions 41 50 for codes cards whose operations should not be reported by SMS messages Oasis user manual MKE22102 Oasis configuration table No E Oasis control panel configuration C An unsplit system only ABC A system with partial setting arming A or AB or ABC A split system A or B or ABC Setting arming without an access code enabled Access by code and card both card and code have to be presented Exit delay beeps C Exit delay beeps while partially setting arming zi Entrance delay beeps Permanent alarm status display for a set system Triggered detector indication M11 Auto bypass of triggered detectors M 12 Final door exit entrance delay extended Mi 13 Device X vi 14 Device Y v 15 Unsetting disarming by service code enabled NH XX JN X X IRIIRIA yo Joo Ja fun Joe fis fe Q K 20 sec Exit delay time Mi 21 Entrance delay time for a main door access Mi 22 Entrance delay time for a final door access MIA Automatic summer time v B Programming phone numbers in maintenance mode enabled MC The type of the communicator installed in the system Notes e The table should be filled in by a service technician according to the system configuration e Ticking checking the field in t
24. tomatic setting unsetting schedule programming telephone numbers for alarm reporting testing detectors or opening their covers without triggering an alarm zone bypassing configuration displaying which code card positions are already occupied Exit maintenance mode by pressing the key 14 System testing The administrator should test the system monthly For testing the control panel should be in operating mode and unset it can also be in maintenance mode When in operating mode the control panel indicates the triggering of a detector but no alarm can be triggered if the system is unset We recommend triggering the detectors zones one by one and verifying that the triggering is indicated on the keypad display by displaying the signal type and source Remote controllers key fobs or panic buttons can be tested in a similar way Oasis user manual 12 MKE22102 Note some detectors for example the JA 83P wireless motion detector are equipped with battery saving functionality which prevents repetitive triggering in short intervals In this case a pre programmed time has to elapse before subsequent triggering is possible up to 5 minutes In maintenance mode close the wireless keypad s flip cover if you are not working with it to save battery energy If anything does not work properly during testing call the installer for help In maintenance mode it is possible to replace discharged batteries in the devices But i
25. y by using the phone s keypad or by SMS It can be also controlled via the Internet after registration on www GSMLink cz For further details see also the communicator s manual User configuration access codes cards The following description is intended for a system administrator who knows the control panel master code or possesses a master card which is authorized to modify the system configuration All the settings can be performed via keying in on a system keypad or very comfortably via a PC running Olink software An unfinished sequence can be cancelled by pressing the key A sequence is stored into control panel memory only after the sequence has been completely entered Note The Oasis JA 80 system has three modes operating mode maintenance mode and service mode Operating mode is for the day to day use of the system by all authorized users e g setting unsetting arming disarming Maintenance mode is for the holder of the master code system administrator to have limited programming of the system e g changing codes cards bypassing and is inaccessible to all other users Service mode is only for installers and is used to program and control all aspects of the system Oasis user manual 9 MKE22102 10 Programming the master code card The master code is used by the house owner or administrator supervisor The factory default setting is 1234 The administrator should program his her own four digit code while
Download Pdf Manuals
Related Search