Portable LED Light System User Manual
Contents
1. our devices back pursuant to the ElektroG Return and disposal of electrical and electronic devices They will either be reevaluated or recycled in accordance with legal provisions 7 OPERATING INSTRUCTIONS SunBurst Portable LED Light System The lamp is manufactured using only high quality components This is an optical precision instrument that must be cleaned and handled with the greatest care Basic contaminations may only be removed with a soft clean dry cloth in order to avoid scratching the lenses Do not immerse the lamp in water sterilization fluid or ultrasound cleaning solutions The product is not waterproof Only use disinfection cloths for severe contamination Disinfection spray must not be used under any circumstances to avoid severely damaging the light Only clean the lamp with a disinfection cloth Do not use gasoline cleaning solutions or aggressive solvents for cleaning Make absolutely sure that your disinfection cloth Is suitable for alcohol sensitive surfaces and for medical facilities such as a dentist s chair Contains no type of 1 propanol Aldehyde phenol or a quaternary ammonium bond such as CaviCide Has a broad spectrum effect against bacteria fungi and viruses Sterilization is not to be done with an autoclave or the following chemicals glutaraldeyde or agents containing iodide To avoid damaging the lamp do not use cleaning methods ot2. purchase 1 This limited liability applies for the end purchaser of the product Client Legal claims by the client or claims by the client against the seller dealer of the device are neither excluded nor limited 2 The guarantee is for 12 months from the time of purchase by the original purchaser In the event of subsequent sale or other change of ownership the warranty will run for the rest of the twelve month period It remains otherwise unchanged 3 During the warranty period defective units according to unilateral decision by Kerr Corporation will be repaired or replaced either by Kerr Corporation or by authorized customer service The client will receive either the repaired unit or a comparable replacement unit from Kerr Corporation Exchanged parts or accessory parts become the property of Kerr Corporation 4 There is no extended or renewed warranty period for repaired or replaced parts 5 This limited warranty does not apply for painted or otherwise personalized parts 6 For expendable parts such as Li ion batteries the warranty is for 12 months from the time of sale 7 This limited warranty does not apply to abnormal signs of use In addition this limited warranty does not apply if a The deficiency has been caused by misuse of the instructions for operation inappropriate use contact with fluids or moisture or extreme heat or climatic conditions and or short term variations in relevant influences or t
3. Portable LED Light System User Manual 2 1 Components of the SunBurst Lighting System 1 Control Unit Check to see that the following components are included in the shipping packaging This unit contains an integrated Li Ion Battery the controls for the LED light and a light to warn of a low battery OPERATING INSTRUCTIONS SunBurst Portable LED Light System 2 Belt Clip a The Control Unit contains a retainer 1 onto which the belt clip is secured To attach the belt clip slide the corresponding slot 2 in the clip over the retainer until a click is heard and the clip is secured b To remove the clip from the Control Unit press this button 3 and slide the belt clip off of the Control Unit 3 LED Light Cable The five components of the LED Light Cable are as follows Headlamp 4 Lens Adapter 5 Smock Clip 6 Plug 7 Grommet not pictured Note Temple clips not pictured suitable for use with your specific frame are also included 4 Battery Supply Battery Charger This unit contains an integrated Li Ion Battery the controls for the LED light and a light to warn of a low battery 1 2 3 4 5 6 7 8 3 OPERATING INSTRUCTIONS SunBurst Portable LED Light System 2 SunBurst Controls and Connectors 1 On Off Switch and Brightness Control Controls the light intensity of the LED 1 When positioned to off the device
4. al Data Weight of the re ector lamp approx 0 7 oz 20 g Weight of control unit 6 0 oz 170 g Diameter of the re ector lamp approx 1 24 in 31 5 mm Dimensions of control unit approx 2 4 in 62 mm x 3 8 in 97 mm x 1 0 in 26 mm W x L x H Voltage Capacity 3 7 V DC 4800 mAH Battery type Li Ion battery Battery charge time Up to 8 hours 90 after 4 hours Battery life Level 3 max approx 7 hours Level 2 approx 14 hours Level 1 minimum approx 35 hours Light intensity Up to 40 000 lumens measured at a distance of 30 cm Environmental temperature for operation and storage 32 F to 104 F 0 to 40 C Speci cation of emitted interference Class B pursuant to 55011 Speci cation of interference resistance Non life support devices IEC 60601 1 2 6 6 Safety Precautions Warnings OPERATING INSTRUCTIONS SunBurst Portable LED Light System 1 Only Orascoptic supplied power supplies part number RM SUNBST CHR are to be used to power the SunBurst LED batteries 2 In order to avoid the risk of permanent damage such as blindness do not aim the lamp directly into the eyes Persons with the risk of eye damage must wear protective eyewear 3 The control unit and the battery must be used exclusively for the purpose described 4 Under no circumstances should you open the housing of the charger or the control unit Never take the devices apart or under
5. her than those prescribed Do not pull on the cable during cleaning 9 Troubleshooting Problem Solution 1 The operational unit is turned on but the display lamp does not light up Make sure that the lamp is properly connected to the control unit Charge the battery 2 The lamp does not light up enough Set the brightness control to a higher setting The battery is too weak Charge the battery 3 Power to the charger is interrupted before the end of the charge cycle such as a power outage As soon as power has been restored the charge cycle will start again 4 The charger display stays red even after 8 hours of charging and does not change to green Send the lighting system with the charger to Orascoptic for evaluation 5 The charger display is red even though there is no connection to the control unit Separate the charger from the electrical outlet for a few seconds If the display is still red after reconnection send the device in to Orascoptic 8 Clean the Lamp 8 10 Limited Manufacturer s Warranty OPERATING INSTRUCTIONS SunBurst Portable LED Light System This limited manufacturer warranty from Kerr Corporation applies for all countries to the extent that no other warranty exists at that location Pursuant to the following contractual provisions Kerr Corporation guarantees material construction and design to be free of deficiencies from the time of first
6. is only on the battery monitoring function 1 represents the lowest power 3 the highest Battery life is the longest with the lowest light intensity and is reduced with increasing light intensity 2 Battery Status LIght This light 2 will begin to weakly illuminate when the battery charge falls below 30 This illumination will increase in intensity as the charge of the battery drops When this occurs recharge the battery at the next available opportunity 3 LED Cable Socket The LED Cable plugs into the control unit in this socket 3 Note When plugging the LED cable into the control unit the red dot on the plug 4 must match up with the red dot on the socket 5 The red dot on the plug is located on a sliding sleeve which acts to lock the plug in place To remove the plug from the socket lift the sliding sleeve and remove the plug When the sleeve is lifted the plug slides easily out 4 Battery Charger Connection Port The battery charger connects to this port 6 The charger s plug will only fit the port in one orientation if the plug doesn t fit the port turn the plug around and try again Don t force it 1 2 3 5 4 6 4 3 Charge The Battery OPERATING INSTRUCTIONS SunBurst Portable LED Light System The SunBurst battery in the control unit is not completely charged on delivery The battery must be fully charged before its first use 1 Plug the charger into the C
7. isruptions of the device This limited warranty replaces all other warranties and declarations of liability whether in written or oral form or other not urgently enforceable legal provisions contractual provisions or non allowed negotiations Kerr Corporation is in no way liable for ancillary causal or collateral damage costs or expenses If the client is a legal person Kerr Corporation assumes no liability for collateral damages costs or expenses 9 For assertion of a warranty claim the original purchase receipt with purchase date is to be enclosed 10 Changes to this limited warranty require the previous written approval of Kerr Corporation U S Technical Support 800 369 3698 Outside the U S Call Your Local Distributor Representation for the EU Sigma Dental Systems Emasdi GmbH Heideland 22 D 24941 Jarplund Weding Germany U S Technical Support 800 369 3698 Outside the U S Call Your Local Distributor Kerr Corporation 3225 Deming Way Suite 190 Middleton WI 53562 USA Phone 608 831 2555 Fax 608 828 5265 www orascoptic com In Canada Synca 800 667 9622 2007 Kerr Corporation Rev A 5 07 AL INSTR SUNBST 001
8. o corrosion oxidation unauthorized intervention or attempts at connection unauthorized opening or repair repair attempts with unacceptable replacement parts abnormal installation accidents forces majeures spillage of food or drinks chemical influences or other influences over which Kerr Corporation has no control including deficiencies to operational parts such as batteries that only have a limited lifespan as well as damage to cables unless the deficiency is caused by a material construction of fabrication error b The client does not report the deficiency within 30 days after it was discovered within the Kerr Corporation warranty period or to an authorized customer service agent c The serial number has been removed scratched off crossed out or changed or is illegible d The deficiency was caused by the fact that the device was used with a part not approved for use by Kerr Corporation was connected to such a part or was otherwise used inappropriately e The deficiency was caused by the short circuit of the battery or the breakage of the seal of the battery housing or manipulation of it or by the fact that the battery was used to an inappropriate end 9 OPERATING INSTRUCTIONS SunBurst Portable LED Light System 8 This limited warranty is the only legal remedy of the client against Kerr Corporation as well as Kerr Corporation s only and exclusive liability to the client for deficiencies and functional d
9. ontrol Unit 2 Plug the charger into the electrical outlet 3 While charging the light 1 on the charging unit will show red When the battery is fully charged the light will be green and the charger will switch to a maintenance mode 1 4 Operate the SunBurst Lighting System 1 Attach the LED headlight to your loupe 1 by tightening the jaws of the mounting hinge to the light mounting block on the bridge of your loupe frame you may have to first attach the mounting block to your loupe frame if it is not already attached 2 Insert the cable grommet through the cable guide 2 and rotate the grommet so that is locks in place 3 Secure the cable to the temple using the supplied temple clip 4 Put the loupe light on and adjust it to a comfortable working position 5 Secure the cable with the smock clip 3 so that the cable does not hinder the view or the work of the user 1 2 3 5 OPERATING INSTRUCTIONS SunBurst Portable LED Light System 5 4 6 Connect the cable to the Control Unit as previously described Note Make sure that the battery status light 4 is not lit indicating a full battery charge 7 Turn the brightness control 5 to the desired intensity Note The life of the battery is shortened as the intensity of the light increases 8 When using the light or when storing the unit never bend the cable tightly to avoid damaging the cable 5 Technic
10. take modifications Misuse of the battery can cause the battery to become hot explode or ignite and may cause serious injury Make sure that the following safety precautions are expressly followed Never open the battery charger or control unit Never make any changes modifications to the battery charger or control unit Do not bring the battery charger or control unit into contact with fire or severe heat over 158 F 70 C Do not use outside Do not short circuit do not connect via a conductor or reverse polarity Protect from fluids and damp environments Do not use a damaged device Maintain storage and operational temperature of 32 F to 104 F 0 40 C 5 Never try to use non Orascoptic supplied charger units or control units 6 The charger must never be used outside 7 Do not use the control or charger units if the housing or plugs are damaged 8 If you determine that the charger or control unit is hot emits an odor or changes color or shape turn it off immediately and disconnect from the power network The device may not be used again and must be immediately returned to Orascoptic 9 If you should find that acid is leaking from the battery and has come into contact with skin or clothing wash the area immediately with running water because this may lead to skin irritation 10 Do not store within reach of children 7 Disposal Instructions We will take
Download Pdf Manuals
Related Search