Patio Heater User Manual
Contents
1. 2 Connect 20 Ib LP Gas Tank Before connecting be sure that there is no debris caught in the head of the LP gas tank 7 head of the regulator valve or in the head of the burner and burner ports SE Line up threads on fitting with those on L J regulator and rotate clockwise until tight HAND e TIGHTENS ONLY DO NOT USE ANY HAND TOOLS TO MAKE THIS CONNECTION Be careful not to cross threads when screwing in FITTING 3 Disconnect 20 Ib LP Gas Tank Before disconnecting make sure the LP gas tank valve is OFF Disconnect gas line to tank by turning knob counterclockwise until it is loose Store the LP gas tank in a proper location SAFETY CHECK Fig 14 Checking for Leaks Your patio heater has been checked at all factory connections for leakage To check the connection at the gas hose regulator cylinder a Make leakage solution by mixing 1 part liquid dish soap and 3 part water pS b Spoon or brush several drops or use a squirt bottle of the solution onto the gas hose regulator regulator cylinder and hose connection c Turn on gas cylinder valve Inspect the connections and look for bubbles d If no bubbles appear the connection is safe e If bubbles appear there is leakage Loosen and re tighten this connection If it still leaks please call customer service at 1 888 376 9601 Lighting Instruction 1 Turn the LP gas tank valve OFF Push control knob in turn OFF and wait 5 minutes for any gas t2. CARE AND MAINTENANCE To obtain the best performance from your heater make sure you perform the following maintenance activities on a regular basis a Keep exterior surfaces clean use warm soapy water for cleaning Never use flammable or corrosive cleaning agents Keep the area around the burner and control assembly dry at all times b Keep airflow unobstructed Clear insect nests or webs away from your heater s exterior and interior c Carbon deposits may create a fire hazard clean dome and emitter with warm soapy water if required d Check your heater for signs of damage or wear and replace components as necessary e Periodically check the hose located within the confines of the cylinder housing for damage f Keep the ventilation clear and free from combustible materials gasoline and other flammable vapors and liquids g Keep the ventilation openings of the cylinder enclosure free and clear from debris h Visually check the burner flame against the illustrations below 1 Flame should be blue with slight yellow tips 2 Light burner rotate knob from HIGH to LOW you should see a smaller flame in LOW position than seen on HIGH Always check flame prior to each use Perform flame check prior to each use If only low flame is seen refer to Burner flame is low in the Troubleshooting section HIGH LOW co o 17 TROUBLESHOOTING Problem Possible Cause Corrective Action B
3. M5 Acorn Nut 7 X15 5 mm Washer X15 PREPARATION Before beginning assembly of product make sure all parts are present Compare parts with package contents list and diagram above If any part is missing or damaged do not attempt to assemble the product Contact customer service for replacement parts Estimated Assembly Time 30 minutes Tools required Wrench Magnetic Head Phillips Screwdriver Not included ASSEMBLY INSTRUCTIONS Fig 1 1 Take the product out of package disassemble Cylinder Cover F by loosening three M6 Bolts Fig 1 F i M6 Bolt nO Oo Of Fig 2 D _at 2 Attach Post D to Platform E with three Botts AA N BB AA three Washers BB and three Nuts F z 7 CC Fig 2 i Sf CC AA M8X1l5mm Bolt NAA X3 68 8 5 mm Washer lt y xs EC M8 Nut gt x3 3 Connect Cylinder Cover F to assembled Back Shroud I by using three Bolts Fig 3 and place the Ring T on the Post D Bolt M6X10 iii Fig 4 4 Fix Tabletop Support H to Tabletop G by using four screws EE Fig 4 EE SS EE ST4 2X10mm Screw Fig 5 5 Disassemble the M5 x 10 mm Bolt from the Post D Put the assembled tabletop G H to Post D Don t reassemble the M5 x 10 mm Bolt to the Post D until Step 6 is complete Notes H When the Tabletop G is well attached follow the steps below to adjust the height A a Adjust the g
4. RED STONE Patio Heater User Manual MODEL PG139HC A DANGER If you smell gas 1 Shut off gas to the appliance 2 Extinguish any open flame 3 If odor continues keep away from the ee eae appliance and immediately call your al Dita gas supplier or fire department Soe A WARNING BOM Do not store or use gasoline or other Toil flammable vapors and liquids in the vicinity of this or any other appliance An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance A WARNING Improper installation adjustment alteration service or maintenance can cause property damage injury or death Read the installation operating and maintenance instructions thoroughly before installing or servicing this equipment A WARNING For outdoor use only w D Before P to your ae call our customer service department at 1 888 376 9601 TABLE OF CONCENTS Product SDCCIICAHONS ccwirsertsuwenlesa cantare wee rales se Wess pene eet eeee Safety MfOrMatlON s isa sucurreinenoleertansagaanateeswaus shines Muaataaeresy Package Cont ntS vis seidee wien en vad eel ceeieene oe nieve aa PatdWat GvG OMENS nctarnscis fasdusr Sdn poate tnautevedtnaameacnet nds Preparat om rnentri n as dawns uauuenecoiest eae arene EREE AES Assembly MASI CONS species scr uei cach ig gene Set ene seyau causation gene tynnctonyae et Installing an LP Gas Tank siya hiecs ure aeaterdas ene Glare els Sa
5. e LP gas supply cylinder to be used must be a Constructed and marked in accordance with the Specifications for LP gas cylinders of the U S Department of Transportation of Dangerous Goods and Commission CAN CSA B339 as applicable b Provided with a listed overfilling prevention device and c Provided with a cylinder connection device compatible with the connection for the appliance Disconnect the cylinder when the appliance is not in use Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance Store the cylinder outdoors in a well ventilated area not in a building garage or other enclosed area out of the reach of children The cylinder used must include a collar to protect the cylinder valve Do not store a spare LP gas cylinder under or near this appliance Never fill the cylinder beyond 80 percent full Place the dust cap tightly on the cylinder valve outlet whenever the cylinder is not in use Install only the type of dust cap on the cylinder valve that is provided with the cylinder valve Other types of caps or plugs may result in a propane leak Inspect the visible portion of the hose before each use of the appliance More frequent cleaning may be required as necessary It is imperative that the control compartment burners and circulating air passageways of the heater be kept clean _ 27 Every part of the heater shall be secure against displacement and s
6. e as shown in the purchaser s receipt This warranty is valid for the original consumer purchaser only and excludes industrial commercial or business use of the product product damage due to shipment or failure which results from alteration product abuse or product misuse where performed by a container service company or consumer We will not be responsible for labor charges and or damage incurred in installation repair or replacement nor for incidental or consequential damage This warranty gives you specific legal rights and you may also have the other rights that vary from state to state 18
7. fety Check rrena ee as ct va Cena tui on at ut LARANE oe od LIGMUIMG Instructions an EO N NEANS Care and Maintenance ss scscccsdcaas cetiia veasasvetes esidacveveiesevenane seasons MPQUBIESITOOUNG 2 aterven ernie a seers us taut R Sea ha i ie wari aithy Warranty soniri ores thts Gon E E E EST PRODUCT SPECIFICATIONS Product Specifications sioria 14 15 eA 15 Certification CSA Height Overall 86 60 inches Reflector Diameter 31 50 inches Rated Heat Input 40 000 BTU HR Fuel Propane LP Gas Supply 20 Lb LP Gas cylinder Manifold Pressure 11 inches W C Injector Size diameter 1 92 mm Safety Features Thermocouple amp Tilt Switch Gas Supply Pressure Max 150 PSI Min 5 PSI A SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble operate or install the product If you have any questions regarding the product please call customer service at 1 888 376 9601 from 8 00 am to 5 00 pm Eastern time Monday to Friday 1 10 11 12 13 The installation must conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI 2223 1 NFPA 54 Natural Gas and Propane Installation Code CSA B149 1 or Propane Storage and Handling Code B149 2 Minimum clearance to the combustible materials is 3 61 ft 1100mm Perform a leak test with a soapy solution a To check gas connections b After connecting a new cy
8. hall be constructed to maintain a fixed relationship between essential parts under normal and reasonable conditions of handling and usage Parts not permanently secured shall be designed so they cannot be incorrectly assembled and cannot be improperly located or misaligned in removing or replacing during cleaning or other servicing 28 CALIFORNIA PROPOSITION 65 WARNING The burning of gas cooking fuel generates some byproducts which are on the list of substances known by the State of California to cause cancer reproductive harm or other birth defects To reduce exposure to these substances always operate this unit according to the use and care manual ensuring you provide good ventilation when cooking with gas PACKAGE CONTENTS A C ZA P Q G DS F a L f S J K E M N Part Description Quantity Part Description Quantity A Top Dome 1 K Cylinder Restraint 1 Chain B KD Dome 4 L Front Shrould 1 Cylinder door C Burner Assembly 1 M Base 1 D Post 1 N Caster 2 E Platform 1 O Latch 2 F Cylinder Cover 1 P Control Knob 1 G Tabletop 1 Q Upper Post Assembly 1 Pre assembled H Tabletop Support 1 R Heat Insulation Plate 1 Assembly l Back Shroud 1 S Cylinder Strip 1 J Regulator amp Hose 1 T Ring 1 Assembly HARDWARE CONTENTS M8X15mm Bolt Hh i X3 8 5 mm Washer A x3 M8 Nut G af X3 M5X10 mm Bolt Wy xs ST4 2X10mm screw te as X4 oae m x12
9. linder c Upon re assembly after disassembly Please refer to the leak test procedure indicated in this instruction manual on page 15 Replace the hose assembly prior to the appliance being put into operation if there is evidence of excessive abrasion or wear or if the hose is damaged The pressure regulator and hose assembly supplied with the appliance must be used The replacement hose assembly regulator shall be that specified by the manufacturer If you don t feel the heater is on a stable surface use a ground screw to fix the base of the heater on the surface where the heater is installed Fix the base on an incline no wider than 15 degrees Place the propane hose with regulator assembly out of pathways where people may trip over it or in areas where the hose will not be subjected to accidental damage This heater is equipped with a battery operated ignition device please refer to the assembly instructions on page 9 Materials or items when stored under the heater will be subjected to intense heat and could be seriously damaged Clothing or other flammable materials should not be hung on_ the heater or placed on under or near the heater Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition Young children should be carefully supervised when they are in the area of the heater Any guard or other protective device removed for servicing the hea
10. o clear 2 Turn the tank valve ON Push control knob in and rotate to PILOT Then push the igniter button until the burner is ignited If the burner fails to remain lit or becomes extinguished turn the burner completely off for 5 minutes and then repeat step 2 3 Once the burner has lit continue to hold the control knob in for 10 seconds then release 4 Turn the control knob from LOW to HIGH to the desired heat setting For complete shutdown 1 Turn the knob to Pilot position first then push in and turn to Off position for complete shut off 2 Turn the LP gas tank valve OFF before removing the LP gas tank In case of failure of normal ignition use the ignition bar clamping a match to reach the burner for ignition through the hole on the bottom of burner diffuser Refer to figure 16 WARNING FOR YOUR SAFETY If at any time you are unable to light burner and smell gas wait 5 minutes to allow gas to dissipate before attempting to light heater WARNING FOR YOUR SAFETY DO NOT touch or move heater for at least 45 minutes after use Allow emitter and dome to cool before touching CAUTION Avoid inhaling fumes emitted from the heater s first use Smoke and odor from the burning of oils used in manufacturing will appear Both smoke and odor will dissipate after approximately 30 minutes The heater should NOT produce thick black smoke Fig 15 Igniter push 4 LOW PILOT e e HIGH OFF Fig 16
11. rip until it is vertical to the post b Adjust the height of the tabletop to desired position c Fix the position of the tabletop by turning the grip clockwise d Turn until the grip is fixed e Clasp the chain to further fix the grip Ii M J O1 W p lt O ct O Fig 6 6 Feed the valve and gas line and pra connect the Burner Assembly C to E Post D 6 1 Feed the valve and gas line into and through the Post D 6 2 Screw Burner Assembly C onto Post D until the hole on the Upper Post Assembly Q is aligned with the holes on top of post D Fix by using one M5 x10 h mm Bolt DD Ensure they are C fully tightened 6 3 Reassemble the M5 x 10 mm Bolt Q to Post D in order to limit the height of the tabletop G Refer to Fig 5 amp Fig 6 DD J Notes mm Bolt mt a Open the igniter cap by unscrewing the cap counterclockwise b Take out the battery included in the pack of Instruction manual mm X3 c Insert the battery to the igniter Fig 7 7 Assemble the four KD Domes B with four M5 x 6 mm Bolts FF four M5 Acorn Nuts GG and four 5 mm Washers HH Attach Top Dome A to assembled KD Domes by using eight M5 x 8 mm Bolts FF eight M5 Acorn Nuts GG and eight 5 mm Washers HH Fig 7 M5X8mm Bolt M x12 M5 Acorn Nut gt X 12 5 mm Washer x12 Fig 8 8 Attach heat insulation plate R onto the bracket of the Burner A
12. ssembly C then attach the Assembled KD Domes B with Top Dome A to Burner Assembly C by using three M5 Acorn Nuts GG and three 5 mm Washers HH Fig 8 M5 Acorn Nut 5 mm Washer 9 Insert the cylinder strip S into the holes of bracket on the shroud sides making the strip parallel to the Base in order to prevent storing the gas cylinder more than 20 Ib 10 Put the gas cylinder into the shroud Keep the cylinder vertically upright on the base for vapor withdraws Fig 9 aaa Fy S Ke nt A fo F S FE 7 Sel ee Fig 10 UU 2 ifr pl Us 12 Fig 11 11 Connect Regulator amp Hose Assembly J to cylinder not included Fig 11 Note Check for leaks after connecting the gas cylinder prior to each use according to the Checking for Leaks section on page 14 12 Attach Cylinder Restraint Chain K to fix the cylinder Fig 12 and close the door after assembly 13 Fig 13 13 If the heater is installed on a surface with a gradient more than 15 fix the base to the surface by using two ground screws L through the two holes on base as lt gt indicated Fig 13 Installing LP Gas Tank 1 Specific size and capacity for gas tank To operate you wil need precision flled standard cylinder with specific size and capacity as shown 20 lb 9 KGS 17 9 in 45 5 cm
13. ter must be replaced prior to operating the heater Installation and repair should be done by qualified service person the heater should be inspected before use and at least annually by a qualified service person More frequent cleaning may be required as necessary It is imperative that the control compartment burners and circulating air passageways of the heater be kept clean A SAFETY INFORMATION 14 15 16 17 18 19 20 21 22 23 24 25 Keep the appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids Do not obstruct the flow of combustion and ventilation air Keep the ventilation opening s of the cylinder enclosure free and clear from debris Use this appliance in a well ventilated space only Do not use it in a building garage or any other enclosed area Use this appliance in outdoor areas described below a With walls on all sides but at least one permanent opening at ground level and no overhead cover b Within a partial enclosure that includes overhead cover and no more than two walls These walls may be parallel or at right angles to each other c Within a partial enclosure that includes overhead cover and no more than two walls The following shall apply i One wall that is equivalent to at least 25 of the total wall area is completely open ii 30 or more in total of the remaining wall area is open and unrestricted Th
14. urner won t light Gas pressure is low The orifice is blocked Control knob is not in ON position Turn tank valve OFF and replace the tank Clear blockage Turn control knob to ON Burner flame is low Carbon build up Thick black smoke Gas pressure is low The control knob is not positioned at High The burner jet may be partially blocked Outdoor temperature is less than 40 F and tank is less than 1 4 full Supply hose is bent or kinked Build up of carton can accumulate over time Blockage in burner Turn tank valve OFF and replace the tank Position the control knob at High Clear blockage Use a full tank Straighten the hose Wipe off before lighting Remove blockage and clean burner inside and outside If problems can not be corrected by using these methods please contact 1 888 376 9601 for assistance ONE YEAR LIMITED WARRANTY The appliance has been manufactured under the highest standards of quality and workmanship We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for one 1 year from the date of purchase A replacements for any defective part will be supplied free of charge for installation by the consumer Defects or damage caused by the use of other than genuine parts are not covered by this warranty This warranty shall be effective from the date of purchas
Download Pdf Manuals
Related Search