INSTALLATION AND USE MANUAL
Contents
1. Connect the equipment to the electricity grid only after you have completed the installation lt is necessary to connect the ground terminal PLEASE NOTE THAT AS ALL POWERED EQUIPMENT FROM THE SUPPLY REQUIRING INSTALLATION IT IS SUBJECT TO COMPLIANCE RULES OF THE COUNTRY IN WHICH IT IS INSTALLED For section and types of wires fuses suitability of materials to installation sites etc Ground connection for heat exchanger and cabine Ground connection Neutral 220V Phase 220V SWN E NF IF YOU NEED TO REPLACE THE FUSE USE THE ONE WITH EXACTLY THE SAME SPECIFICATIONS IF ANY DOUBT ASK YOUR AUTHORIZED DEALER Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 6 di 19 8 BATTERY POWER The batteries are intended to maintain the efficiency of the electronic card allowing the fog emission even in absence of power supply from the electricity grid until the heating system has a sufficient temperature The batteries also have the purpose of activating the motors that rise up plates with cylinders even if it is available the main power supply or 12V from the alarm system Without batteries with dead batteries rechargeable or poor quality ones motors do not pise up plates that push cylinders For this reason it is important To use only high quality alkaline batteries To replace them within the expiry date Anyway to replace them every 12 month When Fast 02 Fast 03 report2. INSTALLATION AND USE MANUAL mod FAST 02 e FAST 03 ENGLISH MANUAL Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 1 di 19 1 Package COMES elise page 2 2 Introduction to the prodUct urna lisina Page 3 3 Conditions or use ana WAMINfS colate Page 3 4 Installations tips of fogging systems recommendations page 4 5 How lo activatethe system cli eee page 5 6 TECNNICalspECIIC CAGO anean aa a aaa DALLO 7 FICCHFICIYVSUPPVN ssaa oi page 6 8 Balle ryYPoWers fois page 9 Description and input and output connections i page 7 10 Connection examples an ille page 8 11 MeaningoffrontlE Ds peule ila ei page 11 12 Setting shooting time and fog flow direction i page 12 13 Installation exchange and cylinders reset iii page 13 14 NGaINntenance acilia Page 14 15 Dereets sand possible sSolUtions ria N a a N anana DAL do 16 WARRANIN lella ar a PARLI The conditions of use will be accepted automatically breaking the security labels on the product 1 PACKAGE CONTENTS Inside the package you will find 1 The machine FAST 02 or FAST 03 2 1 fog fluid charged cylinder for the model FAST 03 1C or two cylinders for the models FAST 03 2C and FAST 02 2C 3 A label to indicate device presence 4 Installation and use manual Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 2 di 19 2 INTROD
3. Close the jumper W3 putting the card in service mode 2 Close the jumper P3 in the RESET position 3 Hold down the button S1 RESET o 5 O o E w the buzzer beeps and then I Motor1down EE Motor 2 down Motor1up x Motor2 up 4 Release the button S1 in this situation you can hear the noise of the z m Nozzle tamper pump and a slight smoke can exit from the nozzle z 5 Remove the jumper W3 o 6 With a slight finger pressure on the cylinder plate of the first motor L push again the button S1 dl W3 7 Replaced the cylinder plate of the first motor without leaving S1 DO NOT USE move the finger from the first cylinder plate to the second one p DO NOT use 4 4 If there were no problems the scrolling test is ended otherwise contact the service center If the plates are completely escaped you will need two down cycles for repositioning The motors of the cylinder plates are ALWAYS powered from the batteries so that any action reduce the autonomy of them Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 14 di 19 CHECKING OF THE PNEUMATIC CIRCUIT AND PRESSURE CONTROL The pneumatic seal test must be done within a few seconds when the pump for nozzle tamper control is turned on as the nozzle temperature rises rapidly reaching temperatures that cause serious burns The air coming out of the nozzle exceeds 200 C Closing with one finger the exit of a
4. When you close the door the buzzler will sound to confirm the tamper is closed Attention Before opening side doors ensure that the alarm control panel is in the service function so that the opening of the circuit anti sabotage or tamper does not cause any alarm Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 13 di 19 14 MAINTENANCE UR Fog generators not require special care however it is recommended the support of qualified and authorized personnel for periodic annual monitoring taking into account the following The charged cylinders have a limit of predetermined duration of 3 years The deadline is printed at the top of the cylinder Verify annually the functioning of the cylinder plates Check the air tightness of the circuit and the operation of the switch The efficiency of the batteries is crucial to guarantee the operation It is recommended to return to your dealer the deadline cylinders but not ended even if not empty An empty cylinder being aluminum steel can be recycled as the common cans It is recommended to change the 6AA internal batteries once every 12 month UP DOWN CYLINDER PLATES SCROLLING TEST If you want only lower a cylinder plate after an activation without the cylinder use the following instructions from step 6 The scrolling check of the cylinder plates is performed by activating the motors without cylinders with the following sequence 1
5. damages 10 CONNECTION EXAMPLE The diagrams and examples below are intended only to a better understanding the operation of the inputs outputs None of the diagrams below represents the single scheme to perform as in respect of the reference standard EN50131 8 there are precise indications and only using all inputs and outputs on the PCB it is possible to respect the standard If UR Fog is used as ANTI ROBBERY device it is necessary a careful assessment of the risks by a security consultant Example of connection UR Fog inputs with outputs of a central anti theft standard Example of connection for anti robbery use with external power supply Example of connection of the UR Fog outputs to drive LEDs and or relays Example of connection of the UR Fog outputs with inputs of an antitheft normally opened Example of connection of the UR Fog outputs with balanced inputs of an antitheft moov p Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 8 di 19 A Example of inputs connection UR Fog with outputs of a central alarm N lt ARE RELE ON OFF NPN OUT ON OFF e INTERNAL SIREN IS ALARM UNIT i FAST 02 FAST 03 a In the diagram above the control panel as example provides to UR Fog power supply between 11 and 14V DC 250 mA max The ON OFF output of this power plant is an Open Collector NPN opened when the system is off and it is closed stably to negative for all
6. that the control panel is provided in the service so that the opening of the circuit anti sabotage or tamper does not cause any shooting TIME TABLE RECCOMENDED FOR SHOOTING BASED ON m TO PROTECT The time of shooting of the cylinders may vary depending on the environment temperature and on the used nozzle The table below is stated considering standard conditions TABLE OF SHOOTING FAST 02 15 30 1 165 270 30 60 2 180 290 45 90 3 195 310 60 10 4 210 330 315 465 330 490 345 505 360 520 75 1500 5 90 170 6 120 210 8 135 230 9 TABLE OF SHOOTING FAST 03 20 30 1 102 158 6 168 245 30 60 2 _ 116 178 180 260 60 90 3 130 190 8 190 275 722 114 4 144 210 9 _ 200 290 88 138 5 156 230 210 305 The first value indicates in m the area to protect the second one indicates the seconds of emission The value in m may vary depending on the density that you desire to obtain With the first value you obtain the maximum of density suggested to guarantee the absence of any residual With the second value you obtain the minimum of density suggested almost 50 cm a higher visibility makes the fog useless In places where a slight residue is not a problem it is possible to increase the time of shooting We remind you that more fog is released more time it takes to have again visibility High levels of fog over suggested limits may leave r
7. the time in which the system still lit The alarm output of the plant is normally open and becomes positive during the alarm time B Example of UR Fog connection with external power supply for anti robbery use E 230V A C STABILIZED POWER SUPPLY IN 230V A C OUT 12V D C EMPTY FAULT ARM KEY TAMPER GND FAST 02 FAST 03 SHOT BUTTON In the diagram above Ur Fog is powered by an external power supply When Fast 02 or 03 is used with an external power supply in case of power failure the machine will not be able to shoot For this reason when the anti robbery function must be guaranteed in the absence of power it is needed to add a rechargeable battery with a capacity of 1 2 Ah 12V in parallel to the output of power supply The arming key is important as required by law to allow you to disarm the device when not in use and maintenance The shooting button when the machine is armed starts the fog emission immediately after pushing the button with time already set in advance To stop the fog emission before the set time turn the key to disarm the machine For safety reasons and to avoid false fog emissions in power when Fast02 or Fast 03 is armed it becomes operative only after 20 Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 9 di 19 After this time the fog emission is instantaneous C Example of outputs connection to drive LEDs or RELAY
8. 0 October 2013 Page 18 di 19 DICHIARAZIONE DI CONFORMITA DECLARATION OF CONFORMITY COSTRUTTORE UR Fog srl sede legale Via Giacinto Collegno 11 10143 Torino Italy Sede operativa Via Poliziano n 34 int 5 10153 Torino Italy MANUFACTURER UR Fog srl Legal office Via Giacinto Collegno 11 10143 Torino Italy Operation and delivery to Via Poliziano 34 int 5 10153 Torino Italy PRODOTTO Nebbiogeno UR Fog PRODUCT UR Fog fog cannon MODELLO FAST 02 FAST03 FAST 03 1C MODEL FAST 02 FAST03 FAST 03 1C ANNO DELLA MARCATURA CE 2013 YEAR OF CE MARK 2013 Con la presente dichiariamo che il prodotto sopraindicato conforme alle prescrizioni di sistema EN 50131 1 e EN 50131 8 With this document we declare that the specified product is constructed respecting the prescriptions described in EN 50131 1 and EN 50131 8 Il prodotto conforme alle seguenti norme The product conforms to the following norms CEI EN 50131 1 2012 CEI EN 50131 8 2010 CEI EN 61000 6 3 2007 A1 2012 CEI EN 61000 3 2 2007 A1 A2 2011 CEI EN 61000 3 3 2009 CEI EN 50130 4 1996 A1 1999 A2 2003 CEI EN 60335 1 2008 A13 2009 A14 2012 A15 2012 Prepared by UR Fog srl Mr Alberto Mori Legal office Via Giacinto Collegno 11 10143 Managing Director Torino Italy UR Fog srl Operation and delivery to Via Poliziano 34 int 5 10153 Torino Italy VAT IT10724850010 Installation and use manual models FAST
9. 02 e FAST 03 rev 1 0 0 October 2013 Page 19 di 19
10. Any certifications required in specific countries are on the responsibility of the distributor of the specific country The documents related to certifications can be requested by mail to support urfog com It is not guaranteed by the manufacturer the use of UR Fog system in the presence of objects that may be damaged anyway in contact with substances based on glycol water and alcohol Any employee or worker that may be exposed to fog must be advised in advance and must be verified if there can be any allergy to the defined above substances At the date of printing of this manual it has never been pointed out any problem related to any allergy UR Fog is anyway not responsible for any damage or condition of use that has not been required by any specific written request and specifically approved prior to the installation of its products For fog fluid please refer to UR Fog fluid safety data sheet published on the website and carefully read it at www urfog com Contact a doctor if for any reason you swallow fog fluid or if after contact with eyes or skin you have any kind of reaction anyway wash it immediately with water and soap Do never stay for a long time in a room filled with fog Do not use charged cylinders that are not the ones suggested by UR Fog and never try to recharge them they are made for a single use Follow your national rules for the dispose of empty cylinders Keep UR Fog cylinders out of reach of baby and animals The nozzle may be hot an
11. GND RELE TAMPER ea kar FAULT TAMPER Ye FAST 02 FAST GND when a cylinder is empty DL EMPTY will switch on when there is a fault DL FAULT will switch on when you open the cylinders door in addition to DL TAMPER the relay switch power max applicable on the outputs 100mA D Example of connection of UR Fog outputs with opened inputs of an alarm system EMPTY FAULT TAMPER GND ND ALARM UNIT FAST 02 FAST 03 The UR Fog outputs are normally opened and connected with input zones of the alarm control panel normally opened According to the diagram above when there is an empty cylinder the entrance area L3 will detect an alarm if a failure occurs or the batteries run down L2 detects an alarm when you open the door of the cylinders L1 detects an alarm Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 10 di 19 E Example of connection of UR Fog outputs to an alarm system with input zones BALANCED a EMPTY FAULT eee ee TAMPER n GND O ror F N e O FAST 02 FAST 03 ALARM UNIT In this diagram putting the resistance value required by the alarm control panel used in the terminal UR Fog with not used outputs the central will see the correct resistance while following the activation of an output you will have a pull down causing the alarm of the corresponding zone 11 MEANING OF FRONT LEDs LED BLUE Lightened means it is arme
12. UCTION TO THE PRODUCT Thank you for purchasing UR Fog product The large patented technological innovations such as the liquid injection system the not returnable cylinders the fact that they don t need to charge and they are also one use the ecological and economic system for the complete emptying of the cylinders together with the heating system all of them make the FAST fog generators the best fog devices with the best performance in the security market Reliable There are not high pressure pumps that loose fluid or tend to stop working There are not high pressure pumps that must be tested periodically UR Fog doubble cylinders technology is a guarantee of working in any condition Competitive Complete use of cylinders liquid avoiding any waste of liquid thanks to pressure control low power consumption Fast and powerful Simple Easy to install machines and also Can be integrated to any existing alarm system Inside there are 2 cylinders included mod FAST 03 1C 1 cylinder 3 CONDITIONS OF USE AND WARNINGS The fog generated by UR Fog does not create particular problems or injuries for a human being for a short stay in a fogged room if the system is used according to the manufacturers recommendations Generated fog is stated as safe for people and animals from an authorized international certification company and is proved that do not leave any residual UR Fog FAST 02 and 03 are certified respecting European laws and regulations
13. can see two cylinders one for Fast 03 1C placed on the cylinder plate A It is necessary to take away the cylinders to remove the blocks placed in the upper part of the cylinders they are only used to avoid the risk of disharge of the liquid during the transport On the rear of cabinet you have to remove precutted wholes on metal case choosing the proper ones after deciding straight or corner installation The round precutted wholes are instead to be used for cables that should go in or out of the machine EMPTY CYLINDER HEATER CYLINDER PLATE CYLINDER i OT PCB Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 5 di 19 6 TECHNICAL SPECIFICATIONS Weight without cylinders and 10 Kg 11 Kg 14 7 Kg battery 40W 40W 45W 60 mA stand by 60 mA stand by 60 mA stand by 7 ELECTRICITY SUPPLY Power 220V supplies energy only to the heating system Electronic card and the motors of the cylinders are supllied from the alarm system and batteries The heating element is of 1KW at the very beginning power consumption is about 500W and in some minutes it goes down reaching average consumption which is about 40W 60W Do not use inverter or UPS unless you have the certainty that they generate a proper sine wave but not rebuilt The max current to be considered for the system is 4A The connection to the electricity grid 230V must be performed by a qualified technician
14. d hot and ready to shoot Flash lights means something is wrong See paragraph 15 DEFECTS AND POSSIBLE SOLUTIONS LED RED It is lightened when at least one cylinder is empty or it is in reserve only FAST 03 1C See paragraph 13 INSTALLATION EXCHANGE AND CYLINDERS RESET EMPTY CYLINDER LED GREEN Flash lights means the heating process is in progress Fast 02 or Fast 03 in this step is heating but is not ready to shoot Lightened steady green light means Fast 02 o Fast 03 is hot and HEATER tuali ready for the fog emission IF THE BLUE LED FLASHING TOGETHER WITH THE SOUND OF CONTINUOUS BUZZER IT IS DETECTED A SERIOUS PROBLEM SEE PARAGRAPH 15 The symbol for empty cylinder in Fast 03 1C has the meaning of RESERVE B That is since the last RESET CYLINDER the machine issued at least 50 of the estimated range of the cylinder Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 11 di 19 12 SETTING SHOOTING TIME AND FOG FLOW DIRECTION SET TIME SHOOTS For the setting of the shooting time after opening the cylinders compartment door at the top of the PCB you must put the jumper in position P3 SET TIME SHOOTS Holding down the button S1 SET all leds on the front will RESET TAMPER flash and each flash is equivalent to one second If you press again the button the shooting time is not added to the one previously set but will restart from zero N B Before opening side doors ensure
15. d touching it may cause burns Do not look directly into the nozzle Do never use UR Fog for any purpose that is not related to protection from thief or robbery the choice of the conditions of use in case of robbery will be suggested by your security consultant Do never use different fog fluids or add any other substance into the cylinders Do not use or keep in charge UR Fog machine in vehicles and do never transport UR Fog before 24 hours it has been shut off During transport it must be not armed Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 3 di 19 4 INSTALLATION TIPS OF FOGGING SYSTEMS RECOMMENDATIONS Please observe the following instructions for mounting UR Fog 2 I i Ce 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 The machine must be installed avoiding to block escape routes 2 Verify the fog does not limit the visibility near stairs landing moving objects that may cause falls down injuries or any damage to persons Do not look directly into the nozzle Do not add any other substance into the cylinders The nozzle may reach high temperatures touch it may cause burns When UR Fog produces fog avoid staying less than 1 meter from the machine When UR Fog is armed avoid staying less than 50 cm from the nozzle Before tests of UR Fog remember to report it in advance to the firefighters in your area to avoid false alarms Remember to put warn
16. esidue Any residue usually goes away by itself within 24 48 hours otherwise being soluble in water it is enough to use a wet cloth for cleaning If you desire to obtain 1 meter visibility average after 60 seconds as specified by the standard EN50131 8 and is used as reference by all manufacturers of Fog generators the second value in m of fog has to be redoubled Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 12 di 19 FOG FLOW DIRECTION To ensure the right direction of the fog flow it is recommended to insert a screw driver of a diameter of the hole and without forcing to orient the nozzle in correct direction of fog emission This allows you to see clearly the direction and keep it in place while tightening To screw and unscrew the nozzle you should use a pair of pliers in good condition to avoid damaging the plating Do not overscrew the nozzle it is sufficient that the teflon nozzle does not move Do not direct the fog jet towards objects and walls less than 2 meters or to the floor if it is installed at a height lower than 2 50 meters WARNING After the fog emission and for a few minutes the nozzle is very hot RISK OF BURNS IF TOUCHED by hands 13 INSTALLATION EXCHANGE AND CYLINDERS RESET The cylinders for fog cannons Fast 02 and Fast 03 are guaranteed to work for 3 years from production date RESET The expiry date is printed on the top of them T After that date c
17. fy a battery case with a tester lt is necessary the use of alkaline batteries of excellent quality It is possible the use of lithium batteries please ask to your dealer When you close the door the buzzer will sound to confirm the closing of tamper containers for recycling l Heavy metals contained in them are recoverable A 7 We recommend to throw away the batteries in the appropriate waste a Empty cylinders are in aluminum for Fast 02 and steel for Fast 03 Metals are easily recyclable Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 15 di 19 DEFECTS AND POSSIBLE SOLUTIONS DEFECT FOUND The three front LEDs flash and the buzzer emits 1 beep minute The buzzer emits 2 beeps minute The buzzer emits 3 beeps minute POSSIBLE CAUSE POSSIBLE SOLUTION The 12 V input voltage is too low or too high Check the external power supply or the alarm unit Low battery but still can shoot Replace batteries See paragraph 14 Low battery power can not shoot Replace batteries See paragraph 14 Batteries absent Insert batteries The buzzer emits 10 False contact battery case Move the batteries turn them consecutive beeps every Connector not correct inserted Remove and reinsert the connector In any case it is useful to use a tester to verify the presence of voltage on the battery case Reset as described in paragraph 13 as described in paragraph 13 The heat excha
18. g input Putting this input to positive if Fast 02 or 03 is hot and armed starts fog emission for the set time see programming section shooting time 5 GND Negative reference connected to terminal 1 OUTPUTS 6 EMPTY Output empty cylinder This output NPN Open Collector closes towards negative direction when at least one of the two cylinders is empty 7 Fault Fault output This output NPN Open Collector closes towards negative when there is a serious malfunction such as batteries expired fault of power supply or temperature control fault which compromises the functioning of the device and which requires a technical action 8 Tamper Tamper output This output NPN Open Collector closes towards negative direction when you open the door cylinders or when the accelerometer detects a sudden movement such as the detachment from the wall 9 GND Negative reference connected to terminal 1 To comply with the requirements of the reference standard EN50131 8 Remember it is necessary to connect all three outputs to an alarm central or an electronic panel that can see all those information in real time and take proper action In order to avoid accidental activation with subsequent fog emission the inputs are in negative security for this reason the disconnection of a wire does not cause activation So it is necessary to check carefully the reliability of connections and protect the cables to the control panel to avoid the risk of accidental
19. he cylinder is stuck in the valvebody Pressure down and then pull Setting the shooting time the buzzer does not sound and the LEDs do not flash The jumper P3 stands in the RESET position See the setting mode of the shooting time at paragraph 12 Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 16 di 19 Warranty The warranty of UR Fog is two years and is handled directly from the dealer or authorized installer so please contact your supplier to take advantage of warranty with the copy of the purchase document that contains the serial number of the machine Not included in the warranty moving parts and or damages depending on the incorrect use unless it is found a manufacturing defect in origin Liquid and cylinders are not covered by warranty BREAKING THE SECURITY LABELS AND THE OPENING OF THE MACHINE YOU WILL ACCEPT WHAT IS WRITTEN ON THIS MANUAL AND ON THE WEB SITE UR Fog srl legal office Via Giacinto Collegno 11 10143 Torino Italy Tel 011 01 33 037 Fax 011 01 33 005 www urfog com support urfog com RESELLER INSTALLER STAMP company to contact for the warranty Serial number Date of installation Signature of installer Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 17 di 19 MAINTENANCE DATE BATTERY EXCHANGE CYLINDER EXCHANGE SIGNATURE Installation and use manual models FAST 02 e FAST 03 rev 1 0
20. ing labels about the presence of UR Fog on the windows Report its installation to the firefighters in your area and eventually to other institutions if needed It is necessary to add an external switch to separate the fog generator from the alarm system and it should be activated before the maintenance to avoid that input tests for example can activate the fog generator Never direct the fog jet towards an object or a wall less than 2 meters if it is possible increase suggested minimum distance Thanks to the power of the jet UR Fog reaches and exceeds more than 10 meters away for first 3 seconds from the point where the machine is installed Setting the shooting time interval between the minimum and maximum shown in the time table avoid doing overshooting even if the produced fog is dry and generally doesn t leave residue A shot that goes far beyond the recommended seconds can create residue problems in the room UR Fog continues to be effective for up to 2 hours without main power 220V thanks to the insulation system that maintains long temperature in the heating system Install at height of about 2 5 meters not to let be reached to avoid possible tampering Install with a maximum inclination of 20 Do not move the machine when it is still hot The main body of UR Fog FAST 02 and Fast 03 that has the heating system closed inside a metal frame should not be opened unless from specific and authorized service centers For no reaso
21. ir from the nozzle while the pump is on you may verify if the pneumatic circuit is correctly sealed If there are no losses inside the circuit under pressure within a few seconds the buzzer will start to operate inside the device and make some sound Otherwise contact the maintenance service If the buzzer sounds before closing the nozzle it means that there is a blockage or malfunction In this case contact the maintenance service VERIFICATION OF BATTERIES AND BATTERY CASE When you have to change the batteries After one year of using Within the deadline printed on them When it is reported they stopped to function If the batteries run down it starts a sequence of acoustic signals 2bips minute battery is low 3bips minutes machine is out of use battery too low 10bip minutes batteries missing or bad contact on battery case plug or cable interrupted The anomaly of the batteries also causes the activation of the output fault useful to signal a possible anomaly When the empty batteries are removed from the battery case the buzzer will sound a sequence of 10bips for each minute After re inserting the new batteries it is suggested to wait at least one minute to verify that the sequence of beeps is not repeated If the sequence of beeps does not stop you have to check the polarity of the batteries and if yes check the batteries are in correct contact with the battery case In this step it is suggested to veri
22. n open and touch insulation before 24 hours UR Fog has been shut off The internal part may reach really high temperature Do not activate the UR Fog machine before the installation is not completed Insert the cylinders as the last procedure and verify the the anti tampering function When the installation is finished test always the system From the moment of UR Fog activation it is necessary at least one hour to reach the minimum temperature need for the fog shoot Install UR Fog avoiding an obstacle in front area which can prevent spread of the fog The external temperature of UR Fog can change from the enviromental temperature to 50 C Request to UR Fog or its distributors to take part in courses for installers to ensure optimal installation of the equipment Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 4 di 19 5 HOWTO ACTIVATE THE SYSTEM It is always recommended to affix the Fast 02 or Fast 03 on a wall also when it is on a flat surface Verify always that the bracket or the support surface are suitable for the weight of the machine lt is suggested not to install the machine behind walls in a limited close area without a specific ventilation to prevent a possible overheating After removing the machine from the package unscrew the two screws that stop the right side panel and revome it Inside it is possible to see the front part of the electronic circuit later called as PCB On the side you
23. nger has not yet reached the minimum temperature of shooting wait for stop flashing standard time of heating 60 min For security reasons and to avoid false fog emissions in power when the machine is armed it becomes operative only after 20 After this time the emission is instantaneous Verify that the alarm once activated has a tension on connectors of at least 12V minute The front red LED is on The machine is armed The front green LED flashes BLUE LED ON but does not shoot The machine does not shoot immediately after arming Wiring error Disconnect electrical power from the machine for a few minutes If this happens again contact technical support Not try to repair the buzzer sounds continuously and the LED flashes blue Error reading thermocouples Can not arm BLUE LED doesn not become on Test the terminal that there is a minimum voltage of between 11V GND 5 ARM 3 when the anti theft system is activated Wiring error When you press the reset cylinder button can not hear the sound of the buzzer the all front leds CAUTION in this case the shooting time The Jumper P3 stands in the is reset SET position flash but the red LED does not reset Reset cylinders Paragraph 13 Set shooting time Paragraph 12 The cylinder does not enter The cylinder does not exit The plate is raised Follow the instructions at paragraph 14 T
24. the signal of battery low paragraph 11 and 14 Battery case test to any action paragraph 14 After inserting the batteries it is important to check they are in a good contact with the battery case to guarantee the proper functioning Describtion of how make tests is in paragraph 14 9 DESCRIPTION OF INPUT AND OUTPUT CONNECTIONS SET o o RESET TAMPER 12 GND in ARM in SHOOTS GND BATTERY CONNECTOR EMPTY FAULT TAMPER GND 1 12V Power input INPUTS 2 GND 3 ARM Power input In these inputs is necessary to provide a stable supply between 11V and 14V DC from the alarm control panel or from an external 12V power supply This power is necessary to the operation of the LED and for the logic of operation In the absence of voltage on this input the logic part continue to operate but not the heater For about 2 hours and 30 minutes or until the temperature of the heat exchanger heating system allows Fast 02 or Fast03 may produce fog The maximum current drawn from UR Fog on this input is 230 mA Arming input Connecting this input to positive Fast 02 or 03 is armed blue frontal led is switched on and when the machine reaches proper temperature it means that it is ready for shooting In case of alarm opening ARM input the fog emission stops immediately even if it has not spent the setting time Installation and use manual models FAST 02 e FAST 03 rev 1 0 0 October 2013 Page 7 di 19 4 SHOOTS shootin
25. ylinders should be changed even if they are not used It is recommend returning the same to the dealer who will take care of RESET TAMFER a disposal For Model Fast 03 1C with one cylinder the reporting of reserve occurs when the machine has shooted at least 50 of the expected duration of the cylinder calculated in seconds and not in quantity of fluid shooten For this reason it is recommended to use only new cylinders and reset only when you actually inserts a new cylinder After removing the screws from the door take away the cylinders and reset the warning light for empty cylinder After this operation insert the new cylinder until you hear the click of the plastic support at its top that goes into the slot then close the door of the cylinder If the cylinder seemed stuck in the upper part DO NOT pull with force make a pressure with two fingers on top of the cylinder such as to lower it Then try again to remove it CYLINDER HEATER If the cylinder does not enter check if the cylinder plate of the motor remains lifted If so see paragraph 14 SECOND MOTOR FIRST MOTOR In case of an empty cylinder to be replaced it is recommended that it be replaced with the second cylinder still charge present in the machine and a new cylinder will replace this last one This in order to ensure a proper rotation of the cylinders and to avoid that a cylinder can remain unused for a long time within the device
Download Pdf Manuals
Related Search