EBDSPIR product guide
Contents
1. e Vacate the room or remain very should take no more than 2 mir Check that the load switches on e To set the final LUX level wait ui enough that lighting is required wise at minimum very slowly t lights come on Note that when e Do not fix to a vibrating surface lights will always come on with e Wire the product using the connector using the diagram on the front e Set the time required page e Mount using one of the two options above e To switch from more than one position simply wire two or more units in parallel Fault Finding LOAD DOES NOT COME ON nd the time to minimum Jo comeron immediately Check to see if the live supply to the circuit is good Strap across still and wait for the load to switch off the L and LIVE OUT terminal to turn the load on utes If the supply and wiring are good check the LUX level setting when movement is detected Increase the LUX level setting to allow the controller to turn on at itil the level of natural daylight is just higher ambient natural light level Starting with the LUX control fully clock irn the control anti clockwise until the If the detection range is smaller than expected check the dia he LUX control is at maximum then the gram above Rotating the sensor slightly may improve the range yccupancy LIGHTS DO NOT GO OFF Ensure that the area is left unoccupied for longer than the se lected timer setting Make sure that the sensor is not adj2. 0674 www cpelectronics co uk enquiry cpelectronics co uk Ref WD101 Issue 7
3. Product Guide lectronics EBDSPIR Ceiling Presence Detector CIRCUIT PROTECTION IF REQUIRED LIVE qO NEUTRAL Overview The EBDSPIR series of presence detector switches are designed to provide automatic control of light ing heating or ventilation loads They detect movement using a PIR sensor and turn the load on When an area is no longer occupied the load will switch off after an adjustable time out period An adjustable internal light sensor provides additional energy saving in lighting applications When an area is occupied lighting is only switched on when the level of natural light is below a preset level When the unit is first powered up the PIR sensor will always detect immediately regardless of whether the room is occupied FLUSH FIXING Hole 64mm Warning be careful bending springs when mounting unit lt D SURFACE FIXING Pull out spring tab and rotate spring arm as shown Installation e The detector should be sited so that the occupants of the room fall Set the LUX level to maximum inside the detection pattern shown overleaf at a recommended height of e Power the unit up the load she 2 8m on the ceiling Note that the lower the sensor is installed the smaller the detection range will be subject to the parameters shown on the diagram e Avoid direct sunlight entering the sensor e Do not site within 1m of forced air heating or ventilation e Do not site within 1m of any lighting
4. acent to circulating air heat ers or lamps Detection Pattern l Area of high sensitivity Areaof lower sensitivity Specification Part Numbers LOAD 8 Amp resistive and incandescent lighting DBB 6 Amp fluorescent lighting 3 Amp compact fluorescent lighting 3 Amp low energy lighting 3 Amp low voltage lighting switch primary of transformer Fluorescent lighting max 6 fittings recommended For fluorescent lighting total power factor correction ca pacitance must not exceed 40uF 3 Amp fans and ventilation equipment Switch SON lighting loads via a contactor SUPPLY VOLTAGE 220 240 Volts AC 50 Hz TIME OUT PERIOD Adjustable 10s to 30m LIGHT LEVEL Light to dark TERMINAL CAPACITY 2 5 mm MATERIAL Flame retardant ABS TYPE Class 2 TEMPERATURE 10 C to 35 C CONFORMITY EMC 89 336 EEC CE LVD 73 23 EEC IMPORTANT NOTICE This device should be installed by a qualified electrician in accordance with the latest edition of the IEE wiring regulations ESTA energy services and technology association il FM 45789 EMS 534520 Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice EBDSPIR Ceiling mounted presence detector Surface mounting back box Melectronics C P Electronics Ltd Brent Crescent London NW10 7XR United Kingdom Tel 44 0 333 900 0671 Fax 44 0 333 900
Download Pdf Manuals
Related Search