Manual - Microh
Contents
1. Points Overhead mounting requires extensive experience including calculating working load limits A knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture are all imperative and should only be performed by a qualified technician Improper installation can result in bodily injury and damage Bo sure to completo all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Regardless of the rigging option you choose for your MICROH TITAN RGB BW wash fixture always be sure to secure your fixture with a safely cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as ilustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safely cable to a carrying handle Please see picture below 5 DMX 512 CONTROL CONNECTIONS This fixture complies with international USITT DMX standards and can be used with either a 3 pin or 5 pin DMX connector Plug in the provided 3 pin XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the MICROH TITAN RGB 8W To connect the units to DMX you must daisy chain the fixtures together as referred in the diagram below Always end your DMX 512 connection with a DMX terminator baw OUTPUT EXTURE R2 prune ei DODDS MEO TURALE roe m COM2. SYSTEM Fan MAX RUN TIME Approximately 4 Hours WARM UP TIME lt 15 Minutes WORKING TEMPERATURE 10 35 C DIMENSIONS 24 6 x 18 89 x 9 84 625mm 480mm 250mm NET WEIGHT 74 95 Ibs 34 kg WARRANTY 2 Year Limited Warranty The Laser diodes are covered under a 6 month replacement warranty 10 MAINTENANCE AND CLEANING The following points have to be considered during the inspection 1 All screws for installing the device or parts of the device must be tightly connected and must not be corroded 2 There must not be any deformations on the housing colour lenses fixations or installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage must be handled by a skilled installer or technician Any safety issues must be resolved CAUTION DISCONNECT POWER BEFORE SERVICING In order to keep the fixture in good condition and extend the life we suggest regular cleaning to the fixture 1 Clean the inside and outside lens each week to avoid the light output from darkening due to accumulation of dust dint etc 2 Clean the fan each week 3 A detailed electrical check by approved technician every three months is advised Ensure the circuit contacts are in good condition and
3. by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does nat necessarily mean that the device is fective It should decrease gradually Please do not project the beam onto combustible substances Fixtures cannot be installed on or near combustible substances Keep more than 50cm distance from wall for proper ventilation and airflow It your fixture is or has become damaged in any way it shall be exclusively replaced or repaired by the manufacturer to avoid any hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Neyer look directly into the light source as sensitive persons may suffer an epileptic shock CAUTION The electric connection must only be carried out by a qualified electrician A Class 3B laser is hazardous to eyes if exposed directly Diffused reflections such as from paper or other matte surfaces are not as harmful 3 OPERATION INSTRUCTIONS Do not tum on the fixture i it has been through severe temperature differences Damage may occur to the fixture Wait until unit is at room temperature to operate The unit should be protected from any tremor or agitation during transport Do not expose the fixture in any excessive heat moisture or any environment with too much dust whan installing Do not lay any power cables on tho floor It may cause electronic shock or damage to persons or eq
4. mode 50 98 Auto beam 100 149 Ruic animalion 150 255 manual Laser off Channel 2 Color select iad 1 255 Color change Pattern Channet 3 Pate 0255 pattems wai o1a7 Manual lorica Channel 4 mous 128 191 From down to up speed 192255 From up to down speed 1 127 Manual Horizontal tussis ee 128 191 From right to left move 192255 From eft to right move Verica Channel 6 VOTE 0255 From slow to fast Horizont Channel 7 rotate 0 255 From slow to fast v2 manual Channel 8 rotate 128 191 Anticlockwise rotate 1982255 Clockwise rotate D sialic zoom T8 From small io big Channel 9 86 170 From big to small 171 255 Auto zoom Palem size D normal size Channel 10 er 1 255 Small to big Channel 11 Sa gas Line to spot Twinkle Channel 12 Tee 0 22 Slow to fast 8 KEY FEATURES RGB Colour Mixing DPSS Diodes Red650nm Green S32nm Blue450nm Pre Programmed Beam Shows and Animations Total of 128 On Board Digital Display Controllable via DMX 3 Pin XLR IDLA Input for PC Control High Speed Quality 35K Scan Motors Max 30 000 pps Eyebolt for Safety Support Wil Support 10 times Weight of Fixture Air Cooled EW Total Laser Output R2500mw G1500mw B2000mw DMX ILDA Sound Auto Master Slave Run Modes 12 DMX Channels Emergency stop box with 5 meter 16 4ft connector cable 9 TECHNICAL SPECIFICATIONS MODEL TITAN RGB 6W LASER DIODE DPSS Red650nm Green 532nm Blue445nm SCANNER 35 Kpps COOLING
5. prevent from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine MICROH parts from your local dealer IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICROH PROFESSIONAL PRODUCTS BY EMAIL AT info microhpro com In the event that your unit is defective in any way please contact your local dealer to obtain an RA number for service repair DISCLAIMER MICROH believes that the information contained within this user manual is accurate However Microh is not responsible for any error or addendums to this manual If you have any comments or general suggestions on how this manual can be improved please contact info microhpro com Thank you
6. using the on board menu Once selected press ENTER to confirm DMXMODE To control the TITAN RGB 6W via DMX select doc on the display By using the UP and DOWN buttons select your desired DMX address and press ENTER to confirm The TITAN RGB has a total 12 channels of DMX ILDA PC CONTROL MODE To run the TITAN RGB 6W in IDLA mode or PC CONTROL MODE simply connect your ILDA signal cable to the DB25 jack located on the rear of the unit and the unit will automatically recognize NOTE when ILDA is connected it supersedes all modes 4 MOUNTING AND INSTALLATION Caution For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriato safety cable Never stand directly below the device when mounting removing or servicing the fixture Whether installing inverted on a truss or ceiling or set on a flat level surface see illustration below Be sure this fixture is kept at least 0 5m 1 5 fi away from any flammable materials decoration etc Always use and install the supplied safely cable as a safety measure to prevent accidental damage andlor injury in the event the clamp fails Mounting
7. MICRO PROFESSIONAL PRODUCTS www microhpro com TITAN RGBGW USER MANUAL TITAN RGB 6W Keep this manual for future reference TABLE OF CONTENTS 1 INTRODUCTION AND UNPACKING 1 2 SAFTEY INSTRUCTIONS 12 3 OPERATION INSTRUCTIONS 23 4 MOUNTING AND INSTALLATION 34 5 DMX 512 CONTROL CONNECTIONS E 6 MENU NAVIGATION 56 7 DMX CHANNELS s 8 KEY FEATURES 7 9 TECHNICAL SPECIFICATIONS 7 10 MAINTENANCE AND CLEANING 8 1 INTRODUCTION AND UNPACKING Thank you for purchasing the MICROH TITAN RGB 6W laser system For your own safety and knowledge please read this manual before installing or operating the device This manual covers the important information on installation and applications Please install and operate the fixture according to instructions Meanwhile please keep this manual for future reference The MICROH LED TITAN RGB 6W laser is made of a new type of high temperature cast aluminum casing The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol This fixture is applicable but not limited to large scale ive performances theater studio nightclubs and discos The MICROH TITAN RGB 6W laser system uses 3 coloured laser diodes that are carefully aligned with the intemal scan mirrors Please carefully unpack it when you receive the fixture and check if it was damaged during the transportation And please check whether the following items are i
8. MON IE ostz our osian iS SAW SPNA For installations where the DMX cable has to run a long distance or is in an electrically noisy environment it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 0 resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fiture in the chain Please see illustrations below 1200 a 1 2 3 4 HaasgBsB MODE UP DOWN ENTER 6 MENU NAVIGATION MODE FUNCTIONS Audi Sound Control uio Auto run Contro deo DMX512 Control The Yo is the address code Press UP or DOWN to sot the address SLAV Slave Control Tho slave unit will do the samo effect as master unit XXX Total running ime This mode displays the total fixture hours that the unit has been in operation Before using the DMX512 controller you should set the channel address It can be set 001 511 address by pressing amp releasing the UP amp DOWN buttons PC Control It the unit is set to ILDA mode use PC software to contro light simply connect ILDA signal to DB25 jack ILDA mode PC control and built in program mode can be identified and transmitted automatically 7 DMX CHANNELS Channel No DMXSI2 fig Content 0 49 Sound control Control Channeli
9. ncluded inside the box Fixture One Power Cord One Bracket Set One User Manual One 2 Safety Instructions CAUTION ELECTRIC SHOCK WARNING USE EXTREME CAUTION WHEN HANDLING WIRES This device has left the factory in perfect condition In order to maintain this condition and to ensure safe operation itis absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual ES important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems It the device has been exposed to temperature changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature and is dry This device falls under protection class I therefore it is essential that the device be grounded The electrical connection must be carried out by a qualified technician The device should only be used with rate voltage and frequency Make sure that the available voltage is not higher than 120V as stated at the end of this manual Make sure the power cord is never crimped or damaged in any way as this could cause shock and damage If your power chord is damaged in any way please purchase a new cable from your local MICROH dealer Always disconnect power when the device is not in use or before cleaning it Never pull out the plug
10. uipment Mako sure to attach the safety chain and ensure the screws are properly screwed in when instaling the fixture Mako sure the lens is in good condition It is recommended to replace the unit if there are any damages or severe scratches Make sure the fixture is operated and installed by qualified personnel Keep the original packaging in case of defective product Any non manufacturer additions modifications or changes in any way will void all warranty Please do not attempt to open unit It is only to be serviced by an authorized technician I this occurs or is apparent the warranty will be voided The fixture s warranty will be voided if there are any malfunctions from not following the user manual or any illegal operation shock short circuit electronic shock lamp broke etc The TITAN RGB 6W has a feature where you can track the overall usage of the fixture fixture hours MASTER SLAVE MODE To run the TITAN RGB 6W in master slave mode the urit must be set to either AUTO or SOUND ACTIVE mode The unit must be linked with Spin XLR to the next fixture All SLAVE units must be set to SLAV through the on board menu Once selected press ENTER to confirm AUTO RUN MODE To run the TITAN RGB 6W in AUTO mode you must set the unit to AUTO PLAY using the on board menu Once selected press ENTER to confirm SOUND ACTIVE MODE To run the TITAN RGB 6W in sound active mode you must set the unit to AUDI
Download Pdf Manuals
Related Search