User Manual
Contents
1. SWITe Model S 1242F 23 8 Broadcast Studio LCD Monitor Bi dE 2200000001060 00 O User Manual Ver V1 0 0V00 Please read this User Manual throughout before using Preface Congratulations on your purchase of this product Please read this user manual carefully 1 All internal technologies of this product are protected including device software and trademark Reproduction in whole or in part without written permission is prohibited 2 All brands and trademarks of SWIT Electronics Co Ltd are protected and other relative trademarks in this user manual are the property of their respective owners 3 Due to constant effort of product development SWIT reserves the right to make changes and improvements to the product described in this manual without prior notice 4 The warranty period of this product is 2 years and does not cover the following 1 Physical damage to the surface of the products including scratches cracks or other damage to the LCD screen or other externally exposed parts 2 The LCD dot defects are not over three 3 Any damage caused by using third party power adaptors 4 Any damage or breakdown caused by use maintenance or storage not according to the user manual 5 The product is disassembled by anyone other than an authorized service center 6 Any damage or breakdown not caused by the product design workmanship or manufacturing quality etc 5 For any suggestions and requirements on this pr2. dry and downy cloth or special LCD cleanser 2 Please do not press hard when cleaning the screen 3 Please do not use water or other chemical cleanser to clean the screen The chemical may damage the LCD 1 Features Full HD 23 8 IPS LCD Panel 1920x1080 resolution H 178 V 178 viewing angle 1000 1 contrast Multiple inputs HD SD SDI HDMI and Composite input Loop through outputs Each of the 2 input HD SD SDI and HDMI has loop through output HDMI converted to SDI output Supported HDMI formats 480i 576i 720p 50 59 94 60 1080i 50 59 94 60 1080P 23 98 24 25 29 97 30 and the output SDI will embed the audio 48KHz from HDMI Waveform Y Cb Cr R G B and full scale There are totally 6 kinds of waveform display available under both SDI and HDMI to check the Luminance Y Blue difference Cb Red difference Cr Red R Green G Blue B and the Y Cb Cr can be simultaneously displayed R G B can be simultaneously displayed and each of the waveforms can be set to full scale display Vector scope The displayed vector scope pattern is available under both SDI and HDMI represents saturation as distance from the center of the circle and hue as the angle in standard position around it Histogram R G B The histogram is a bar graph that shows the distribution of luminance values in the picture There re R G B histograms that individually displayed simultaneously avai
3. RIGHTNESS 0 100 value adjustment 3 HUE 0 100 value adjustment Only available under CVBS NTSC input 4 SATURATION 0 100 value adjustment 5 SHARPNESS 0 100 value adjustment 6 BACKLIGHT 0 100 value adjustment 3 2 SYSTEM submenu The SYSTEM submenu includes 1 RATIO Aspect ratio 16 9 4 3 selection 2 SCAN UNDERSCAN OVERSCAN 3 ZOOM OFF ZOOM1 and ZOOM selection 4 FLIP Select ON to flip the picture by 180 5 RESET Select YES to recover all to factory setting 3 3 OSD submenu The OSD submenu includes 1 LANGUAGE Menu language selection 2 H POSITION Menu horizontal position 0 100 adjustment real time preview and default value 50 3 V POSITION Menu vertical position 0 100 adjustment real time preview and default value 50 4 DURATION Menu timeout setting 5 60s Set a time in seconds in which the menu will automatically quit if remains idle Default 15 SYSTEM OSD TITLE DISPLAY F KEY COLOR UMD PICTURE OSD TITLE DISPLAY FREY COLOR UMD PICTURE SYSTEM OSD TITLE DISPLAY F KEY COLOR UMD PICTURE CONTRAST TT BRIGHTNESS in HUE o SATURATION ME SHARPNESS IE 7 BACKLIGHT MENINI 77 ADJ ENTER EXIT SYSTEM 16 9 UNDERSCAN OFF OFF NO ADJ ENTER EXIT LANGUAGE H POSITION V POSITION DURATION ENGLISH 2 7 ADJ ENTER EXIT 3 4 TITLE s
4. UT HDMI converted to SDI output BNC connector 7 CVBS IN Composite video input BNC connector 8 SDI IN1 SDI input BNC connector 9 SDI IN2 SDI input BNC connector 0 HDMI LOOP HDMI loop through output HDMI A connector 1 REMOTE DB9 socket external controlling signal input See details in 4 REMOTE interface definition 2 DC IN 11V 17V BACK UP Connect with 4 pin XLR power adaptor Pin 1 Negative Pin 4 Positive 19 DC IN 11V 17V MAIN Connect with 4 pin XLR power adaptor Pin 1 Negative Pin 4 Positive 14 VESA installation position standard 10 x 10cm VESA thread Input Formats Input Supported formats CVBS PAL NTSC 4801 5761 480P 576P 10801 60 59 94 50 720p 60 59 94 50 1080p 60 59 94 50 30 29 97 25 24 23 98 10801 60 59 94 50 SMPTE 274M 1080p 30 29 97 25 24 23 98 SDi SMPTE RP211 1080psf 30 29 97 25 24 23 98 SMPTE 296M 720p 60 59 94 50 SMPTE 125M 480i 59 94 ITU R BT 656 576i 50 HDMI 3 Menu Operation 1 Press MENU and it will display menu system 2 Revolve ENTER to select an item The selected item will be highlighted display 3 Press ENTER to enter the selected item 4 Under menu system press MENU to back to previous menu The menu will automatically save and quit if it remains idle 3 1 PICTURE submenu The PICTURE submenu includes 1 CONTRAST 0 100 value adjustment 2 B
5. audio output Video Format CVBS NTSC PAL 1080i 60 59 94 50 SMPTE 274M 1080p 30 29 97 25 24 23 98 2 1080psf 30 29 97 25 24 23 98 720p 60 59 94 50 480i 59 94 5761 50 4801 5761 480P 576P 1080i 60 59 94 50 720p 60 59 94 50 1080p 60 59 94 50 30 29 97 25 24 23 98 HDMI Working voltage DC battery 11V 17V lt 42W OC 40 10 90 19 060 10 90 576 X 387 X 81mm 6 98kg Power consumption Working temperature Working humidity Storage temperature Storage humidity Dimensions w o stand Net weight w o stand 6 Standard Package Monitor Desktop Stand Feet User Manual Warranty Card Power Adaptor Power Cable 7 Optional Accessories CO 1 7 1 Battery plate amp Installation a CD LEZ bee T 1 Take off the rub cover on the rear panel see Fig 1 CS 2 Insert the DC cable of S 7004S A into the hole and plug 7 fa onto the power socket inside the hole see Fig 2 3 Fix the battery plate onto the rear panel by the supplied ie gt screws see Fig 3 S 7004S S 7004A 1 2 3 7 2 VESA Desk top stand 10x10cm VESA 8 Installation Dimension 8 1 The main body in mm 8 2 With deskt
6. being turned on for 5 seconds press AD ERT EXIT WFM the waveform display will be turned off 1 DISPLAY Press Display to display safe area scale marker title UMD function status and the current input signal information 12 MENU Press to enter Menu 3 ENTER Select and Apply Under menu system revolve ENTER to adjust settings and press to apply and out of menu system directly revolve ENTER to adjust volume and directly press to mute 4 BRIGHT Revolve BRIGHT to adjust brightness value from 0 100 Default value is 50 CONTRAST Revolve CONTRAST to adjust contrast value from 0 100 Default value is 50 SATURATION Revolve SATURATION to adjust saturation value from 0 100 Default value is 50 POWER Power on off Connect with power cable press the POWER to switch on the monitor Press again to switch off Note Disconnect with power cable if the monitor will not be used for a period of time PHONE 3 5mm earphone socket for SDI HDMI embedded audio and analog audio monitoring 9 TALLY Light Red Green and Yellow 3 color TALLY indicator 1 14 1 Battery plate Install V mount or Gold mount battery plates install position with a hole to connect the battery plate power wires to the main board inside 2 Handle 3 HDMI IN HDMI input HDMI A connector 4 SDI LOOP2 SDI loop through output BNC connector 5 SDI LOOP1 SDI loop through output BNC connector 6 SDI O
7. erate the image because hue and saturation can be adjusted quicker and more accurately UMD Support TSL UMD protocol so that TALLY UMD can be remotely controlled User definable function keys There are 4 function keys on the monitor front panel which permit users to define shortcuts for the various functions User editable video title User can edit a video title for the current camera and the title will display on the top of screen 3 color TALLY light There s a 3 color TALLY light in the front panel of monitor and TALLY signal is input via DB 9 connector on the rear panel Main Backup Power Supply The monitor provides 2 DC power inputs for main and backup power 2 Panel Instruction Front view 19 8 9 10 01 02 3 1 Desktop Stand Feet dismountable 2 Speaker For SDI HDMI embedded audio and analog audio monitoring Will not work if earphone is plugged in 3 SDI1 Press SDI1 to switch to SDI input 1 4 SDI2 Press SDI2 to switch to SDI input 2 5 HDMI Press HDMI to switch to HDMI input 6 CVBS Press CVBS to switch to CVBS input WAVEFORM 7 9 F1 F2 F3 User definable function keys u 0 WFM Display waveform RGB Press WFM once it will display the waveform on the a screen a CR Within 5 seconds press WFM again it will display the waveform menu Revolve ENTER to select a waveform display mode and turn it on After the waveform
8. lable under both SDI and HDMI 16 ch audio meter Under HDSDI it displays 16 channels audio bars with mark and under SDSDI or HDMI it displays 8 channels audio bars with mark The audio bar is green and will turn yellow when audio exceeds 20dB and turn red when exceeds 9dB SDI timecode Under SDI input it can display the SMPTE timecode VITC1 VITC2 or LTC which is used extensively for synchronization and for logging and identifying material in recorded media Peaking focus assist red blue switch The Peaking focus assist function is to mark the sharpest edges of the image with red or blue color for users to check if the subjects are focused Multi Scale Marker The monitor has 16 9 native LCD panel and supports 4 3 13 9 14 9 15 9 1 85 1 and 2 35 1 scales marker for different video producing Zebra stripes Zebra Stripes are used to check if the image is over exposed or not by showing black and white lines on the monitor It is considered over exposed when luminance value exceeds 90 False color The false color is used to aid in the setting of camera exposure Under false color mode there s a color chart on the bottom of screen for reference The over exposed subjects above 101 IRE on the monitor will display as RED and the underexposed subjects will display as BLUE For correct exposed subjects it will display as green and pink Blue Only Under Blue Only Mode only blue pixels are used to gen
9. o UMD or fixed TITLE or turn DISPLAY PARITY lt EVEN gt OFF FKEY COLOR 4 BAUD RATE 38400 19200 or 9600 selection UMD 5 PARITY EVEN or NONE selection ADJ ENTER EXIT 4 REMOTE Interface Definition The TALLY light controlling port and UMD signal port are controlling through the DB 9 socket at the rear panel and terminal description is as follows eo N 9 N 4 N 3 N 2 N 1 N Be gt Y u 7 ES b _ A a 9 8 7 6 o X j i p A GND 485A 485B The RED light is on when connecting the terminal R with GND and goes out when disconnecting 2 The GREEN light is on when connecting the terminal G with GND and goes out when disconnecting 3 The YELLOW light is on when connecting the terminal Y with GND and goes out when disconnecting 4 485B Rx 5 485A Rx Note 3 color TALLY light can be remotely controlled by REMOTE port 5 Specification LCD Performance 23 8 inches 527 X 296mm 1920 x RGB x 1080 16 9 4 3 adjustable 250cd m 1000 1 16 77 million colors Horizontal 178 Vertical 178 Size Display area Resolution Aspect ratio Brightness Contrast Color Viewing angle Interface BNC x2 HD SD SDI input x2 Input BNC x1 CVBS input HDMI x1 HDMI input BNC x2 HD SD SDI loop output x2 BNC x1 HDMI converted to SDI output Output HDMI x1 HDMI loop output SDI HDMI embedded
10. oduct please contact us through phone fax Email etc SWIT Electronics Co Ltd Address 10 Hengtong Road Nanjing Economic and Technological Development Zone Nanjing 210038 P R China Phone 86 25 85805753 Fax 86 25 85805296 Email contact swit cc Website http www swit cc Maintenance e The Monitor 1 Please keep the signal terminals and the cooling vent away from knife edge metal or liquid in order to avoid short circuit and damage 2 Please don t try to disassemble any parts of the monitor by yourself which would probably damage the monitor and do harm to human body and it will cause the invalidation of product warranty 3 Please don t touch the screen with your fingers which would probably deface the screen 4 Please don t press the screen the LCD is extremely exquisite and flimsy e The power Please use the power adapter provided or recommended by the manufacturer in order to avoid damage For a third party power adapter please make sure the voltage range supplied power and polarity of power lead are fit Please disconnect the power cable under the following situations 1 If you do not operate this monitor for a period of time 2 If the power cable or power adaptor is damaged 3 If the monitor housing is broken eo Working Environment 1 Please don t lay this product on the unstable place 2 Please don t lay this product in hot cold or wet location e Cleaning 1 Please clean the screen with
11. op stand feet in mm 8 3 With VESA desktop stand in mm 179 18 SWIT
12. ope switch on off OSD 08 PATTERN Internal colorbar switch on off Are 09 RGB HIST R G B Histogram switch on off 10 TIMECODE SDI timecode display switch on off COLOR 11 F COLOR False color mode switch on off i 12 AUDIO BAR Audio meter display switch on off 13 FOCUS Peaking focus assist switch on off 14 FLIP Image flip 15 COLOR TEMP Adjust color temperature 16 UMD Adjust UMD 01 RATIO gt 02 SCAN gt 03 ZOOM gt ENTER EXIT 3 7 COLOR submenu The color submenu is to change the color temperature settings User can select color temperature as 6500K 5600K 9300K or define color temperature by RGB GAIN and RGB BIAS 1 COLOR TEMP 6500K 5600K 9300K USER1 USER2 USER3 2 R GAIN 0 255 value adjustment PICTURE COLOR TEMP 6500K gt 3 G GAIN 0 255 value adjustment en Den OSD G GAIN m 4 B GAIN 0 255 value adjustment oe San EEE 5 R BIAS 0 255 value adjustment DISPLAY R BIAS x 6 G BIAS 0 255 value adjustment F KEY G BIAS m i 7 B BIAS 0 255 value adjustment B BIAS UMD Remark RGB GAIN and RGB BIAS settings are only available when Color temp is set as USER1 2 3 ENTER EXIT 3 8 UMD submenu The UMD submenu includes 1 RS485 ADDR 1 126 address selection dla SYSTEM UMD POS 4 BOTTOM gt 2 UMD POS Select UMD display at TOP or Zap one a Ue BOTTOM on the screen TITLE BAUD RATE 38400 gt 3 UMD DISP Switch t
13. ubmenu Revolve ENTER button to select the letters and PICTURE press ENTER to input Select SPACE to input space and DEL to delete the left letter Max 10 letters are supported DISPLAY After setting press MENU the system will save ae data to current user and quit menu The menu will UMD automatically save and quit if it remains idle 3 5 DISPLAY submenu The DISPLAY submenu includes PICTURE 1 INFO ON OFF When select on the infos SYSTEM OSD including Input format aspect ratio E underscan overscan zoom status will be display on left top screen Ala i COLOR 2 TITLE User edited title on off UMD 3 MARKER SEL Select the scale marker from 4 3 13 9 14 9 15 9 1 85 1 2 35 1 and OFF 0 A K Uy W TITLE CAMERA 4 5 E F O P Y Z 1 ADJ Ee ENTER EXIT DISPLAY INFO TITLE MARKER SEL SAFE AREA MARKER CLR ADJ ENTER EXIT 4 SAFE AREA Select the safe area scale from 80 85 90 95 and OFF 5 MARKER CLR Select the color of markers from WHITE RED GREEN BLUE BLACK and GRAY 3 6 F KEY submenu The F KEY Settings Submenu is to define Function Key F1 F2 and F3 The available functions are 01 RATIO Aspect ratio 16 9 4 3 switch 02 SCAN Underscan Overscan switch 03 ZOOM Picture Zoom in 04 B W Color Black amp white switch 05 BLUE ONLY Blue only mode switch on off 06 ZEBRA Zebra over exposure switch on off jm 07 VECTOR Vector sc
Download Pdf Manuals
Related Search