Source Four XT HID Zoom User Manual
Contents
1. Asia service etcasia com Web www etcconnect com m Copyright 2013 ETC All Rights Reserved m Product information and specifications subject to change 7065M1200 m Rev D m Released 2013 102. parks e Outdoor performance venues non dimming e Museums e Public sculptures Outdoor signage Lamp and Ballast Information HID Lamps CAUTION Do not use lamps other than the HID in Source Four XT fixtures Use of lamps other than HID will void UL cUL safety compliance and your warranty CAUTION This fixture must be grounded CAUTION The fixture is sold for either 120V or 220V 230V 50Hz 240V 277V to match the power supply Verify that the lamp and ballast voltage requirements matches your power supply Connecting the fixture to the wrong voltage voids the re a warranty Ceramic Metal Halide oie Lamp code Watts Base Bulb eee Color temp CRI en vared RT157 CDM150 T6 830 150 G12 16 14 000 3000 K 85 12 000 hours RT158 CDM150 T6 942 12 700 4200 K 96 12 000 hours Ballast e Acceptable voltage is either 120V or 220V 277V 410 50 60 Hz only depending on the model purchased e 120V Nominal Ballast e 120V 10 60Hz 1 5 Amps operating current e 220V 230V 50Hz 240V 277V Nominal Ballast e 277V 10 60Hz e 220V 230V 240V 10 50Hz 60Hz 0 61 Amps operating current at 277V 0 69 Amps operating current at 230V 150 watt high power factor fully encapsulated electronic ballast e Tilt down reflector housing for lamp change without disturbing focus A CAUTION Source Four HID fixtures are not dimmable Dimming will damage the bal
3. Source Four XT HID Zoom 15 30 and 25 50 User Manual Production Dates May 2013 Present Copyright 2013 Electronic Theatre Controls Inc All Rights reserved Product information and specifications subject to change Part Number 7065M1200 Rev D Released 2013 10 Table of Contents Basic Assembly rs we BA Eee Ene LEY 1 Basic Information 0 000 eee ee eee 1 Lamp and Ballast Information 22222 2 Compliance Information 222222 3 Replacing the HID Lamp 0 0020 eee nenn 4 Installation a2 2er EEE 6 Electrical u tiret ea Da er bend A 6 Removing and Installing the Barrel 04 7 Adjustments oe oia i r a eee 9 Focusing the Beam 222240220 EE bee 9 Shaping the Beam 2uensneee eee 11 Adjusting the Angle 0 0 0 0 e eee eee 13 Cleaning the Lenses and Reflector 00 een 14 Cleaning Glass Lenses 0 0 c cece eee 14 Cleaning the reflector 1 2 0 2 cece eee 15 ETC permits the reproduction of materials in this manual only for non commercial purposes All other rights are reserved by ETC ETC intends this document whether printed or electronic to be provided in its entirety ETC is a registered trademark of Electronic Theatre Controls Inc in the United States and other countries Other product and company names mentioned herein may be trademarks and or service marks of their resp
4. alling or servicing the fixture Failure to follow this warning can result in serious injury or death To remove the barrel Step 1 Loosen the three 4mm hex screws securing the barrel to the housing There is a nylon retaining washer on each screw to prevent it from slipping out of the reflector housing 4mm screw with nylon retaining washer Figure 4 4mm Hex Screws on the Barrel Step 2 Slide the barrel off the fixture Step 3 Use the two studs on the barrel to hang it on the side of the yoke while you work Figure 5 Barrel Hanging Studs and Slots on Yoke Step 4 Use the safety loop and the optional safety cable to secure the barrel if needed To install the barrel Step 1 Slide the barrel down over the lens rails aligning the three ridges of the barrel with the ridges of the housing Barrel ridges 4mm hex Figure 6 Barrel Installation Step 2 Tighten the three 4mm hex screws around the barrel Partially tighten each screw working progressively around the barrel until all have been tightened to 25in Ibs 2 82 Nm DO NOT OVERTIGHTEN The nylon washer should be tightly sandwiched between the two flanges at each screw connection Source Four XT HID Zoom User Manual Adjustments Focusing the Beam Two internal lenses control the size and focus of the light beam Each lens is mounted in frames and these frames slide along the rails The lens frames are secured in the desired location wi
5. e lens towards the lamp sharpens the focus so that the edges are hard e Moving the lens away from the lamp softens the focus so that the edges are soft Shape the beam with the shutters and install a pattern if needed See Shaping the Beam page 11 Source Four XT HID Zoom User Manual Shaping the Beam The beam can be shaped using patterns and the shutters The beam can also be colored with colored glass in the pattern holder Note The projected beam is the inverse of the inserted patterns and shutter adjustments That is for a pattern to be projected right side up it is inserted upside down and backwards Likewise moving a shutter affects its opposite image Pattern and Color Projection The two pattern holder slots are inside the fixture and immediately in front of the shutters The holder slots accommodate B size and glass pattern holders The holder holds 2 5 and 2 75 inch diameter patterns One pattern holder for steel patterns is supplied with the fixture Additional glass or steel pattern holders are available from ETC lt 2 75 gt Diameter 3 70 gt Figure 9 Pattern Holder Dimensions Step 1 Remove the barrel as described in Removing and Installing the Barrel page 7 Step 2 Insert the pattern into the pattern holder upside down and in reverse of the desired projection Pattern holder slots Figure 10 Pattern Holder Location Step 3 Adjust the focus lens if needed See Focusing t
6. eaning the Lenses and Reflector WARNING Do not use ammonia based or other harsh commercial cleaners Clean lens and reflector only as directed Commercially available glass cleaning agents should be avoided as they may contain ammonia other harsh chemical detergents or abrasive agents These cleaners may damage the glass surface and the Anti Reflective coatings Do not immerse or soak the glass in any cleaning solution Replace lenses if they contain visible damage cracks or deep scratches that may impair their effectiveness Cleaning Glass Lenses Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Reflector Field lens Focus lens Figure 13 Internal Glass Lenses Remove the barrel Refer to Removing and Installing the Barrel page 7 If needed move the lenses to access both sides of the lenses Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 50 50 mixture of each can be used to clean the glass surface If the reflector needs to be cleaned refer to Cleaning the reflector page 15 Return the lenses to the required positions if needed Replace the barrel Source Four XT HID Zoom User Manual Cleaning the reflector WARNING Disconnect power and allow the lamp to cool down before attempting to clean the reflector To quickly clean the reflector remove the lens tube and clean the dust from the reflector with a blast o
7. ective owners This product is protected by one or more of the following U S Patents 6 016 038 6 150 774 6 788 011 6 806 659 6 683 423 and 7 023 543 Basic Assembly 15 30 shown Pattern holder Barrel Ballast Pattern holder slots Field lens and frame Reflector housing Focus lens and frame Figure 1 Components of the Source Four HID Zoom Fixture WARNING Please note the following safety warnings before use Do not use this fixture with a damaged power lead If the power lead cordset is damaged it must be replaced Do not mount the fixture on or near combustible surfaces Do not use this fixture if glass lens is deeply scratched or cracked Damaged lenses must be replaced Do not operate the fixture for long periods of time without the barrel installed Remove foam packing from internal lenses before connecting power to your fixture Basic Information ETC s Source Four XT HID Zoom is a Source Four spotlight for all weather use Powerful Source Four optics light output and energy savings in a sleek IP66 rated watertight and dust proof design XT features ETC s Source Four Zoom optical system plus our long life 12 000 hour 150W HID lamp Hang by yoke place on ground attach to poles and other structures There are two Source Four XT HID models available 15 30 Zoom 25 50 Zoom Applications e Houses of worship Retail store logos and patterns e Theme
8. f oil free air You may also wipe the reflector with a clean lint free cloth If either method is not sufficient follow these steps Refer to Figure 13 Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 To protect the lamp during cleaning remove the lamp assembly Refer to Replacing the HID Lamp page 4 Remove the barrel Refer to Removing and Installing the Barrel page 7 Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 50 50 mixture of each can be used to clean the glass surface Gently wipe the reflector Reinstall the barrel Reinstall the lamp assembly 16 Source Four XT HID Zoom User Manual 17 Corporate Headquarters 3031 Pleasant View Road P O Box 620979 Middleton Wisconsin 53562 0979 USA m Tel 608 831 4116 Fax 608 836 1736 London UK Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6UU UK m Tel 44 0 20 8896 1000 m Fax 44 0 20 8896 2000 Rome IT a Via Pieve Torina 48 00156 Rome Italy Tel 39 06 32 111 683 m Fax 44 0 20 8752 8486 Holzkirchen DE Ohmstrasse 3 83607 Holzkirchen Germany m Tel 49 80 24 47 00 0 Fax 49 80 24 47 00 3 00 Hong Kong Rm 1801 18 F Tower 1 Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong m Tel 852 2799 1220 m Fax 852 2799 9325 Service Americas service etcconnect com m UK service etceurope com m DE techserv hoki etcconnect com m
9. he Beam page 8 Step 4 Reinstall the barrel Adjusting Shutters Use the shutters to shape the light beam For example you may want to use them to block the light from falling on part of a building Or you may want to frame a sign The shutters are held in place by a spring shutter retention system You do not need to tighten or loosen the screws to make adjustments Step 1 Remove the barrel as described in Removing and Installing the Barrel page 7 Step 2 Turn the Source Four XT on and aim it at the structure you are illuminating Step 3 Pull the shutters outward so that the aperture is fully open Shutters Shutter tabs Figure 11 Shutters and Their Tabs Step 4 Use the tabs on the shutters to move them to block the beam as needed Keep in mind that the blocking is reversed Step 5 Reinstall the barrel Source Four XT HID Zoom User Manual Adjusting the Angle The Source Four XT provides the capability to adjust the fixture angle e The standard yoke provides 12 to 7 horizontal tilt when ground mounted The standard yoke provides 45 to 40 when bracket or pole mounted e The optional long yoke allows 90 to 35 fixture angle including straight up or down aiming Figure 12 Yoke Locking Screw Step 1 Using an 8mm hex wrench loosen the two yoke locking screws Do not remove them Step 2 Tilt the fixture to the desired position Step 3 Tighten the two yoke locking screws to secure in position Cl
10. last and void your warranty 2 Source Four XT HID Zoom User Manual Compliance Information Complies with Low Voltage Directive and EMC Directive Tested to Standards EN60598 1 EN60598 2 17 EN60922 EN55015 EN61000 3 2 EN61000 3 3 EN61547 Replacing the HID Lamp A lamp must be installed before you use the fixture The lamp can be replaced without affecting the focus WARNING Do not replace the lamp when it is raining or snowing Do not stand in water while replacing the lamp Failure to follow this warning can result in serious injury or death WARNING Disconnect power and let the lamp cool before replacing Note Verify that the HID lamp you intend to install is suitable for your fixture s ballast See Lamp and Ballast Information page 2 Operating HID lamps above their rated voltage reduces lamp life and can cause premature lamp failure The facility s voltage must match the voltage of the fixture and its ballast Step 1 Ensure power has been disconnected and the lamp is cool before replacing the lamp Step 2 Loosen the screw securing the ballast Ballast screw Lamp cap Figure 2 Ballast and Reflector Housing Base on the Back of the Fixture Step 3 Rotate the reflector housing to reveal the lamp cap Step 4 Loosen the four screws of the lamp cap The screws are captive so they will stay in the cap Step 5 Pull the lamp assembly straight out of the fixture Step 6 Carefu
11. lly pull the old lamp out of the ceramic base Step 7 Holding it by the base remove the new HID lamp from its box 4 Source Four XT HID Zoom User Manual A CAUTION Use caution when installing or replacing any lamp When installing or replacing lamp be sure to point the lamp away from your face and away from others before inserting it firmly into the assembly This may prevent injuries if the lamp should break INCORRECT OX CORRECT e Note To avoid premature lamp failure do not touch the lamp glass If you do clean it carefully with isopropyl alcohol and a clean lint free cloth Allow to dry before operation Step 8 Align the flat sides of the lamp base with the lamp retaining clips on both sides of the socket HID lamp Lamp retainer clips Lamp housing Figure 3 Inserting the Lamp into the Lamp Housing Step 9 Push down on the lamp base until the lamp seats firmly When properly installed the base of the lamp will be secured by the lamp retaining clips A CAUTION Improperly installed lamps cause premature lamp failure and socket problems Step 10 Reinstall the lamp assembly by aligning the lamp cap with the fixture Ensure the wire is pushed aside and not touching the lamp Step 11 Tighten the screws in a zig zag pattern Installation Install on a suitable rigid permanent base with secured bolts This can include poured concrete pads factory supplied pole top and wall mount bracke
12. th two knurled thumb screws e The field lens is nearest the lamp and controls the width of the beam The focus lens is furthermost from the lamp and controls the focus of the beam Focus lens Thumb screw and frame Field lens and frame Figure 7 Lens Arrangement WARNING Do not remove the barrel and expose the interior of the fixture to water such as rain or snow Do not stand in water while installing or servicing the fixture Failure to follow this warning can result in serious injury or death Step 1 Remove the barrel as described in Removing and Installing the Barrel page 7 Step 2 Turn the Source Four XT on and aim it at a flat surface Step 3 Pull the shutters outward so that the aperture is fully open Refer to Adjusting Shutters page 12 Step 4 Step 5 Step 6 Step 7 Step 8 Loosen the two knurled thumb screws on the field lens holder Lens holder thumb screws Figure 8 Thumb Screws Gently slide the field lens back and forth on the rails until you get the desired width of the beam and then finger tighten the thumb screws e Moving the lens towards the lamp narrows the field angle of the beam Moving the lens away from the lamp widens the field angle of the beam Loosen the two knurled thumb screws on the focus lens holder Gently slide the focus lens back and forth on the rails until you get the desired focus of the beam and then finger tighten the thumb screws e Moving th
13. ts and other attachments which meet the published weight and wind load requirements for the fixture Use the full sized template that is included in the installation instructions or download the template at www etcconnect com Source Four XT HID Weight Wind Load XT HID 25 50 34 5 Ibs exclusive of accessories color filters and patterns 1 15 square feet of effective projected area EPA XT HID 15 30 39 Ibs exclusive of accessories color filters and patterns 1 4 square feet of effective projected area EPA WARNING Do not use this fixture with a damaged power lead If the power lead cordset is damaged it must be replaced Failure to follow this warning can result in serious injury or death WARNING All third party mounting hardware should be corrosion resistant and designed for use where installed Electrical CAUTION The fixture must be grounded and wired in accordance with national state and local electrical codes Failure to do may result in serious personal injury The fixture is completely pre wired at the factory there is no need for entry into the ballast housing Source Four XT HID Zoom User Manual Removing and Installing the Barrel The barrel can be removed for adjustments focusing installing patterns and cleaning the lenses WARNING Do not remove the barrel and expose the interior of the fixture to water such as rain or snow Do not stand in water while inst
Download Pdf Manuals
Related Search