VDW61S - Venini
Contents
1. 31 VENINI Think Appliances Pty Ltd 416 424 Barry Rd Coolaroo VIC 3048 Sales Telephone 1300 132 824 Service Telephone 1800 444 357 Website www thinkappliances com 322. o Use the shorter and lower temperature cycles for everything but the dirtiest dishes Shorter cycles use less energy and work just as well Modern detergents also work just as well at lower temperatures 21 Cleaning and maintenance IMPORTANT The appliance should be disconnected from your mains supply before commencing any cleaning process The filter system Your appliance is fitted with three levels of filtering these are located in the base of the dishwasher for ease of access 1 Main filter 2 Coarse filter 3 Fine filter Main filter Food and soil particles are trapped by this filter and pulverised by a special jet on the lower spray arm This debris is then washed down the drain Coarse filter Larger items such as pieces of bone or glass which could clog the drain are trapped in this filter Fine filter This filter holds soil and food residue in the sump area and prevents it from being redeposited on the dishes during a wash cycle i I MPORTANT Whilst the filtering system is efficient your dishwasher is not a waste disposal unit All items being washed inside of the dishwasher should have food scraps removed from them before being loaded into the appliance Cleaning the filters For best performance and results the entire filter assembly should be thoroughly cleaned regularly ideally after each wash cycle 1 Turn the coarse filter anti clockwise and then lift it upwards The fine
3. filter will come out with the coarse filter Rinse out these sections under a tap to remove any food debris that remains in it ZZ 2 Pull out the main filter and rinse this under the tap to remove any food debris that is trapped in it 3 Place all filters back in their original position 4 You must turn the coarse filter clockwise to lock it back into position IMPORTANT If a glass gets smashed inside of the appliance you must check there is no glass in the filter before the machine is used again as this can cause a drainage failure jam IMPORTANT THE DISHWASHER SHOULD NEVER BE STOP SET ON A WASH CYCLE WITHOUT THE FILTERS BEING Vw INSIDE OF THE APPLIANCE Cleaning the spray arms The spray arms should be cleaned regularly to prevent hard water deposits from clogging the spray arm jets and bearings o To remove the top spray arm unscrew the nut and take out the washer that sits on top of the spray arm and pull to remove o Gently pull upwards to remove the bottom spray arm o Wash the spray arm in warm soapy water and use a soft brush to clean the jets o Rinse the spray arm thoroughly and then reassemble the spray arm back in its original position Cleaning the control panel IMPORTANT Do not use any abrasive cleaner or household polish on either the control panel or operating parts o Wipe over the control panel using a brand new damp cloth with warm water 23 Cleaning the do
4. 1 LED display 12 Program selection dial siae ed cd a io a 1 ON OFF button Turns the appliance on off 2 Start Pause button Pauses and resumes a wash cycle 3 Delay start button Delays the start of the wash cycle 4 Child lock button Locks the control panel from misuse 5 3 in 1 button To be activated when using 3 in 1 tablets Indicator lights symbols_ Indicates that a function is active or requires attention 10 Using your dishwasher Before first use Filling with rinse aid The rinse aid is released during the final rinse and it helps to prevent water from forming droplets on your dishes These droplets will lead to spots and streaks being left on items after the wash program has completed o Your dishwasher is designed to utilise liquid rinse aid o The rinse aid dispenser is located inside the drop down door next to the detergent dispenser o To access the rinse aid dispenser you should turn the cap anticlockwise and it will pop out of the hole Then slowly pour in liquid rinse aid the rinse aid dispenser will hold approximately 140 ml of rinse aid o You should continue to fill with rinse aid until the level indicator turns completely black o Be careful not to overfill the dispenser as this could cause oversudsing when a wash program is selected Wipe away any rinse aid excess or spillages with a damp cloth o Replace the cap and turn it clockwise until it locks into position o You
5. N AN ENVIRONMENTALLY FRIENDLY MANNER Connecting to the mains water supply IMPORTANT Do not connect the appliance to your mains water supply using an old or an existing water inlet hose The inlet hose supplied with the dishwasher is the ONLY one that should be used DO NOT CONNECT THE WATER INLET HOSE TO A HOT WATER TAP o Before connection we would advise running the water to ensure that it is clear and free from impurities as dirty water could block the inlet pipe and damage the machine o The inlet hose will be located inside the cavity of the dishwasher o Connect the water inlet hose to a threaded water tap that has a 3 4 thread and to the inlet hose connector on the appliance o Fully tighten the inlet hose to the water tap and the dishwasher 28 Connecting to the water outlet o Secure the drain hose so that it cannot move whilst the dishwasher is In use o Place the end of the drain hose in your drain pipe and push it a Short way down max120mm DO NOT SEAL o IMPORTANT Do not insert the drain hose too deeply into the pipe as this may cause siphoning o NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH 29 Connecting to the power supply o IMPORTANT The electrical socket must still be accessible once the appliance is installed o Consult the rating plate located on the right hand side of the drop down door BEFORE making the electrical connections Ensure that the voltage
6. NT This should only be attempted when the cycle has only just started otherwise the detergent tablet may have already released or you could have hot water escaping O Turn off the appliance using the on off button and wait for a minute Turn the appliance back on using the on off button Select your new wash program After about 10 seconds you will hear the appliance begin to fill with water and the wash program will have started 19 At the end of a wash program o When the wash program is finished a buzzer will sound o Open the door of the appliance o Use the ON OFF button to switch the dishwasher off o Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still not and more susceptible to breakages They will also dry better Adding an item to a wash cycle IMPORTANT This should only be attempted when the cycle has only just started otherwise the detergent tablet may have already released or you could have hot water escaping o Slightly open the door of the appliance and wait for a minute before fully opening the door to avoid scalding by the hot water o The cycle will pause The machine will emit a beep and display error code E 1 in the display o Add the item and then close the door The cycle will resume after approximately 10 seconds Delay start o Set your desired wash program as outlined on page 18 o Press the delay start button to delay the st
7. USER MANUAL FOR YOUR VENINI VDW61S 60 cm Full Height Freestanding Dishwasher er TT f ie Cte MU M 1 ve i ced y MG ki PAGT UMI UE mA hich VENI NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a Safe place so that it is easily available for future reference for you or any person not familiar with the operation of the appliance JW 26 06 13 Contents Environmental note Important safety information Specifications Product and aperture dimensions Product specifications Electrical details Description of the appliance Control panel Using your dishwasher Before first use Filling with rinse aid Setting the rinse aid level Filling with dishwasher detergent Concentrated detergent Detergent tablets Loading the upper basket Adjusting the upper basket Loading the lower basket The cutlery basket Loading dishes and cutlery Program table Setting a wash program Changing a wash program At the end of a wash program Adding an item to the wash cycle Delay start Rinse aid and salt indicator neons Saving energy using your dishwasher Cleaning and maintenance The filter system Cleaning the filters Cleaning the spray arms Cleaning the control panel Cleaning the door Error code failure system General troubleshooting Installation Connec
8. a dishwasher o Remove leftovers and soften the remnants of burnt food in pans prior to loading dishes in the appliance o Once the dishwasher has been loaded check that the spray arms can move freely If the spray arm comes into contact with any item then you should rearrange the wash load o Cups glasses pans etc should all be loaded with their bases upwards so that water does not collect inside of them o Cutlery and dishes should not cover each other otherwise you may get poor wash results o Do not allow glasses to touch inside the dishwasher otherwise damage may occur o Small objects can be placed inside of the cutlery basket 16 The following items are NOT suitable for washing inside a dishwasher o Cutlery with a handle of mother of pearl wood horn or china o Plastic items that are not resistant to heat o Cutlery that consists of glued parts that are not resistant to heat o Cutlery items or crockery that are bonded o Copper or pewter items o Lead crystal glass o Wooden platters o Synthetic fibre items The following items are not always suitable for yp washing inside a dishwasher o Stoneware should only be washed if the manufacturer of the item has marked it as dishwasher safe o Plastic items such as lunchboxes should only be washed if the manufacturer has marked it as dishwasher safe o Glazed crockery may fade with repeated washing inside of a dishwasher o Items made
9. art of the wash o Keep pressing the delay start button until your desired amount of delay is displayed in hours o The maximum amount of delay is 24 hours Rinse aid indicator o The rinse aid indicator on the control panel will let you know when the appliance needs rinse aid adding to it o The A light indicates that you need to add rinse aid to the appliance You should follow the procedure outlined on pages 11 20 Saving energy using your dishwasher Loading dishes o Refer to the relevant section of this manual for instructions on placing items in the dishwasher for the most efficient cleaning o Only run the dishwasher when it is full for optimum energy and water usage o Check the program table to select the most efficient program according to the size and type of the load o The ECONOMY program washes your items at a lower temperature and uses less water during the cycle That is better for the environment and helps to cut energy costs as well as your water bill if you re on a water meter Usage o Clean the filters regularly both to keep the dishwasher clean and to maintain its efficiency o Always remember to switch the appliance off standby when you have finished using it Energy is wasted by leaving appliances on Standby o You do not need to rinse dishes off before loading If you prefer to pre rinse use cold water on your dishes before loading them but do not waste water by letting it run continuously
10. ckaging materials that Venini uses are environmentally friendly and can be recycled o Please discard all packaging material with due regard for the environment IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Venini Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information contained in this booklet please contact the retailer where you purchased your unit General Safety o Repairs to your appliance must only be carried out by authorised service agents Any attempt by an inexperienced person to repair the appliance could result in injury or damage to your dishwasher o If you notice that the mains cable is damaged The appliance must not be used The same applies if you notice that the worktop control panel or base area is damaged As this could allow access to the internal components of the machine o The appliance should be turned off and isolated from the mains Supply before either cleaning or maintenance work is attempted o The mains cable must not be used to pull the plug out of the electrical socket o The machine should not be sprayed with water o The external surface of the appliance may become hot whilst your dishwasher is in use o It is possible for small animals to chew either mains cables or water hoses which could cause an electric shock hazard Installation o The installation i
11. d follow the detergent manufacturer s recommendations 12 O O The section marked 2 in the diagram can have separate detergent placed in it for any wash cycle that has a pre wash element to it however this is optional This must be a liquid or powder detergent not another detergent tablet Shut the detergent dispenser lid so that it clicks shut securely At the beginning of a wash cycle the clip will open and the tablet powder liquid will enter the dishwasher Concentrated detergent O O The use of the NORMAL program with concentrated detergents reduces pollution and is good for your dishes This wash program is specifically suited to the dirt dissolving properties of the enzymes of concentrated detergent For this reason the NORMAL program in which concentrated detergent is used can achieve the same results achieved in the INTENSIVE program Detergent tablets O Different brands of detergent tablets dissolve at different speeds For this reason some detergent tablets cannot dissolve and develop their full cleaning power during short programs It is recommended that you use longer programs when using detergent tablets to ensure the complete removal of detergent residues If you are using 3 in 1 detergent tablets you should check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturer s instructions 3 in 1 detergent tablets contain detergen
12. g of pots and pans the cup shelf spikes can be folded down 14 Loading the lower basket The lower basket is most suited to washing larger and more heavily soiled items such aS Saucepans saucepan lids and serving dishes You can also load bowls and a variety of plates into the lower basket iii G Dessert dishes H Dinner plates Side plates Saucepans and serving bowls must always be placed with their bases upwards Deep saucepans should be slanted to allow water to run off o The bottom rack has prongs that can be folded downwards to allow for easier loading of larger saucepans and serving bowls 15 The cutlery basket Cutlery should be placed inside of the cutlery basket The cutlery basket should then be placed in the appropriate position in the lower basket Serving fork Serving spoon Gravy ladle l Teaspoons Zi Dessert spoons 3 Soup spoons 4 Forks ay Knives 6 7 8 o For the best washing performance cutlery should be placed through the slots in the top of the cutlery basket IMPORTANT Do not allow items of cutlery to fall through the bottom of the cutlery basket as this may cause damage to the spray arm and or the cutlery If the bottom of the basket begins to deteriorate and allows items to fall through you should replace the cutlery basket Loading dishes and cutlery Household cloths sponges or any other object that may absorb water SHOULD NOT be washed in
13. ith the standards currently in force Product dimensions Height 850 8 5 mm Width 600 mm Depth 600 mm Lees I S A riage NA a AI aN PIFFA ai nn ar AN S ad a A a Product specifications O O 12 Place settings 6 functions Normal Intensive Heavy Soak Rapid Rinse 6 temperatures 40 C 49 C 55 C 60 C 65 C 70 C Noise level 52 dB LED display Delay start Anti leak device Anti flood device Concealed heating element Collapsible plate racks Height adjustable upper basket Adjustable feet Residual drying 3 in 1 option Energy efficiency details Energy efficiency class 3 Star Water Consumption 4 star Electrical details Rated voltage 220 240 Vac 50 Hz Supply connection 10A GPO For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice The rating plate of your dishwasher is located on the right hand side of the drop down door Model Number Serial Number Date of Purchase Description of the appliance Upper basket Spray arms Lower basket Filters Detergent dispenser Rinse Aid dispenser Cutlery basket Cup holder Control panel ON OFF button Start Pause button Delay start button Child lock button 3 in 1 button Child lock indicator 3 In 1 indicator Water inlet malfunction indicator Rinse aid indicator 10 Drying indicator 1
14. n to wash rinse later that day The wash program times that are quoted are intended as a guide only Please note that factors external to the machine e g the temperature of your water supply your water pressure etc can affect the time it takes for the wash program to complete Or 3in1 Pre wash 67 Hot rinse Minutes 70 C Drying Wash 40 C Hot rinse 49 C 15 grams 50 main wash Minutes NORMAL is the testing program for AS NZS 2007 1 18 Setting a wash program Make sure that the before first use section has been followed Check whether the appliance needs rinse aid adding to it Pull out the top and bottom baskets then load them in accordance with the loading instructions Push the top and bottom baskets fully back into position Add detergent Close the dispenser before starting the dishwasher Turn the appliance on by using the ON OFF button IMPORTANT Wait for 5 seconds before pressing the program selection button otherwise the appliance may not function correctly Press the program selection button to choose an appropriate wash program for the load that you are washing Where applicable the relevant program indicator will light to show which program you have selected Close the door firmly so that you hear the door lock click shut After a few seconds you will hear the appliance begin to fill with water and the wash program will have started Changing the wash program IMPORTA
15. nse aid levels A normal phenomenon Aluminium utensils have rubbed against dishes This is normal The rinse aid dispenser is overfilled or rinse aid has been spilt inside the appliance Dishwasher isn t level The safety lock is engaged Select a more intense wash program Make sure that the spray arms and the detergent dispenser are not being impeded by large dishes Refer to the relevant sections of this booklet to ensure that the detergent and rinse aid levels are set correctly Ensure that the appliance is loaded correctly You may get a small amount of steam coming through the vent by the door latch during drying and water draining Use a mild abrasive cleaner to eliminate the marks Make sure that the appliance is loaded correctly in future A small amount of clean water in the base of the appliance is not something to be concerned about Take care not to overfill the rinse aid dispenser Spilt rinse aid could cause oversudsing and lead to overflowing Wipe away any spills immediately with a damp cloth Make sure that the dishwasher is level Turn off the safety lock by pressing the safety lock button Turn the appliance off and on again using the power button 21 Installation IMPORTANT THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERSON THE MANUFACTURER ONLY SANCTIONS THE INSTALLATION GIVEN IN THIS INSTRUCTION MANUAL YOU SHOULD DISPOSE OF ALL PACKAGING I
16. nstructions contained within this user manual Should be followed o It is obligatory for the completed installation to comply with all relevant building regulations and local water authority requirements o Before the first use of the appliance you should follow the steps listed in the Before first use section on page 11 and page 31 of this manual Care should be taken not to trap the power supply cable underneath the appliance whilst installing it No attempt should be made to alter or modify the specifications of this appliance In daily use O This appliance is only designed to wash normal domestic washloads If you use your dishwasher in any other way or it is incorrectly used then the manufacturer accepts no liability for any damage that might be caused and any guarantee will be void It is recommended that the appliance is unplugged and the water supply is turned off after the machine is used The detergents and rinse aid that you place in this appliance Should be suitable for automatic dishwashers With regards to dosage levels the detergent manufacturer s recommendations Should be followed Sharp knifes or ones with long blades are a potential safety hazard when placed in an upright position in the cutlery basket We would recommend that these items are placed horizontally in the upper basket You should not wash any items that have come into contact with corrosive acidic or alkaline chemicals paint petr
17. of silverware or aluminium can discolour when washed inside a dishwasher o Any food residue should be removed from silver items immediately as this can also result in discolouration o Certain types of glass may become dull or cloudy after a large number of washes 17 Program table o The ECONOMY program is suitable for cleaning a typical load of dirty dishes and is the most efficient in terms of its combined energy and water consumption Program Program Description Detergent information of cycle pre main times kWh L Normal x XK For normally soiled loads such as pots plates glasses and lightly soiled pans Wash 45 C Rinse Hot rinse 49 C Drying 5 grams 112 pre rinse 25 grams main wash Or3in1l Minutes aoe For the heaviest Pre wash 5 grams 145 soiled loads such as 40 C pre rinse Minutes pots pans Wash 55 C 25 grams casserole dishes and Rinse main wash dishes that have Hot rinse been sitting with 65 C Or3inl dried food on them Drying for awhile Heavy For heavily soiled Wash 60 C 5 grams 135 loads such as pots Rinse pre rinse Minutes pans plates Rinse 25 grams glasses and lightly Hot rinse main wash soiled pots and 65 C bowls A standard Drying daily cycle For lightly soiled loads that only need to be rinsed and dried only A shorter wash for lightly soiled loads that do not need drying To rinse dishes that Pre wash 8 Minutes you pla
18. ol iron or Steel debris You should not open the door whilst the appliance is set on a wash program Depending on which stage that the wash program is at hot water could escape the machine You should not leave the door of the appliance open unless you are loading or unloading the dishwasher You should not stand or sit on the door when it is open Child Safety O Your dishwasher should only be used by adults You should not allow children in the area of the machine unsupervised You Should not let them touch the controls or play with the appliance It could be possible for a child or pet to gain access to the dishwasher if the door is left open Therefore please check the inside of the appliance before setting it on a wash cycle Any packaging that is removed from the machine should be kept away from children All detergents should be kept out of children s reach in a safe place Some water will remain inside the dishwasher when it has completed a wash cycle This water is not suitable for drinking and may contain residues from the detergents that are used in the appliance This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Declaration of conformity O This appliance complies w
19. or o To clean the edge around the outside of the door you should use a soft damp cloth only o To prevent water from penetrating the door lock or electrical components DO NOT use a Spray cleaner of any kind o DO NOT use any abrasive cleaner or scouring pads on the inner or outer surfaces as they may cause damage to them Error code failure system The following error codes Flashing display neon s can possibly be remedied by the customer and the maintenance steps outlined below Should be followed BEFORE COMPLETING ANY MAINTAINEANCE ON THE APPLIANCE IT SHOULD BE DISCONNECTED FROM YOUR MAINS POWER SUPPLY E 2 amp the water inlet malfunction indicator 8 flash o Longer than expected fill time Check the water pressure of your mains water supply Clean the mesh filter that sits in the inlet hose Ensure that the inlet hose is not kinked or crushed Make sure the water tap that the machine is connected to is turned on fully v Make sure the drain hose has been connected as specified SS E 3 flashes o Longer or extended drain time v The drain pipe may be placed in too high a position or incorrectly Check the installation instructions and ensure that the installation is correct v Check that the outlet hose is not kinked or crushed v Make sure that the drain hose has not been extended beyond its original length E 5 flashes o The machine has sensed water in the base v Check that the o
20. reaching the plug is the same as that on the rating plate o DO NOT REMOVE THE RATING PLATE AS THE INFORMATION ON IT IS IMPORTANT o The moulded plug that is supplied with the appliance must be placed into an earthed and insulated socket o Broken or damaged power leads must only be replaced by a Suitably qualified person A power lead of a similar type must be used in replacement o Power lead type HO5VV F 3G 1 5 o IMPORTANT We do not recommend that this appliance is connected to an extension lead 30 Levelling the appliance o IMPORTANT Your dishwasher must be level for it to operate properly o Make sure that the dishwasher is supported whilst it is being levelled otherwise it may tip over o The feet can be adjusted by hand or by using a Spanner o Use a spirit level to check that the appliance is level o Check that the appliance is level from Side to side o Check that the appliance is level from front to back ss Check level from side to side Before first use You should check the following before using the appliance for the first time That the dishwasher is level and fixed in position That the water tap is fully open That there are no leaks at either end of the drain or inlet hoses That the inlet and outlet hose are fully tightened That the inlet and outlet hoses are not kinked That the power is switched on That the rinse aid dispenser has been filled OO OO
21. should refill the rinse aid dispenser when the rinse aid indicator lights on the control panel 9 o IMPORTANT If you are using 3 in 1 dishwasher tablets then you should still fill the rinse aid dispenser 11 Setting the rinse aid level The amount of rinse aid that the dishwasher requires also depends on the hardness of your water You should experiment with the rinse aid setting until you find a level that gives the best results o On the first wash cycle we would recommend that the rinse aid level is set to number 4 o If you get water spots and poor drying performance then you should turn the Rinse arrow anticlockwise and increase the setting to the next number o You should continue to adjust the rinse aid level upwards until you get no water spots o If you get cloudiness or streaking on your dishes the rinse aid level is set too high and it is causing foaming during the wash cycle Turn the arrow clockwise and lower the setting to the next number Filling with dishwasher detergent The detergent dispenser must be refilled at the start of each wash cycle apart from the Rinse wash program o Open the lid that closes over the detergent dispenser and place the detergent inside the dispenser The section marked 1 in the diagram is for the main wash cycle detergent Only one detergent tablet should be placed in the dispenser at any one time If you are using detergent powder or liquid you shoul
22. supply is connected properly and that the water is turned on The system is designed to detect an overflow If it does then it will run the drain pump continuously when there is power to the appliance You will get a level of operating noise during a wash cycle in particular when food is being removed from items and when the detergent dispenser places the tablet into the tub Ensure that everything is loaded as per The manufacturer s loading instructions If the dishwasher is not going to be used for a period of time then you Should make sure that the appliance is set on a wash program once a week Otherwise the seal around the motor may dry out and cause noise Ensure that if you are using 3 in 1 detergent tablets in conjunction with rinse aid that the levels are set correctly Always wipe up any excess rinse aid or rinse aid spillages immediately Stained tub Detergent with Use a detergent without colourant interior colourant was used Dishes are not fully dried Rinse aid dispenser is empty Make sure that the rinse aid dispenser is filled with rinse aid 26 Dishes and pans are not clean Spots and filming on glasses and pans Black or grey marks on dishes Water Standing in the bottom of the tub Dishwasher leaks The Dishwasher IS not responding Improper program Improper loading Extremely hard water Low inlet temperature Improper loading Improper detergent Improper ri
23. t rinse aid and salt and as such it may be beneficial to select the lowest setting for water hardness See setting the rinse aid section for details You should only use 3 in 1 tablets with the Normal Intensive or Heavy wash programs When using the 3 in 1 tablets you should press the 3 in 1 button on the control panel to activate the 3 in 1 setting which will optimise the wash for use with 3 in 1 tablets 13 Loading the upper basket The upper basket is most suited to washing delicate and light dishware such as glasses coffee amp tea cups saucers plates bowls and shallow pans that are not heavily soiled A Cups B Glasses C Saucers o You should position the dishes and cookware in such a way that they are not moved by the spray of water during the wash cycle o Use the diagram above as a guide to the most appropriate way to load the upper basket Adjusting the upper basket Your dishwasher has an adjustable upper basket which you can alter to the most suitable position for the items you are going to wash in the upper and lower baskets o The height of the upper basket can be adjusted by placing the wheels on a different height of the rails Long items such as cutlery salad servers and knives should be placed on the shelf so they do not obstruct the rotation of the spray arms o IMPORTANT The upper basket must be empty when you are removing it from the guide supports o NOTE For easier stackin
24. ting to the mains water supply Connecting to the water outlet Connecting to the power supply Levelling the appliance Before first use Contact details ENVIRONMENTAL NOTE Note Before discarding an old appliance switch off and disconnect it from the power supply Cut off and render any plug useless Cut the cable off directly behind the appliance to prevent misuse This should be undertaken by a competent person Disable the door lock to make sure that children cannot get stuck inside the appliance This appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol akah on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product o The pa
25. ur appliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen then they will not complete a repair This includes situations where appliances have been tiled in sealed in with sealant have wooden obstructions placed in front of the appliance like plinths Or any installation other than the one specified by the manufacturer has been completed Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance I MPORTANT The manufacturer operates a policy of continuous improvement and reserves the right to adjust and modify its products without prior notification ZS General troubleshooting PROBLEM POSSIBLE CAUSES Fuse blown or the circuit breaker has tripped Dishwasher doesn t run Drain pump doesn t stop Noise Suds in the tub Power supply is not switched on Water pressure Is low Some audible sounds are normal Utensils are not secure in the baskets or something small has dropped into the basket Motor hums Improper detergent use Spilled rinse aid WHAT TO DO Replace the fuse or reset the circuit breaker Remove any other appliances that are sharing the same circuit with the dishwasher Make sure that the dishwasher is turned on and that the door is closed securely Make sure that the power cord is fully plugged into the wall socket Check that the water
26. utlet hose is not kinked or crushed v Check that there are no blockages in the drain hose or the drainage system that the appliance is connected to v The drain pipe may be placed in too high a position or incorrectly Check the installation instructions and ensure that the installation is correct 24 Other error codes ERROR CODE MEANING POSSIBLE CAUSES The door is open when the dishwasher is operating El sensor ater leakage Water leakage occurs Heating element Abnormal heating IMPORTANT If any of the above fault codes appears then you Should check the trouble shooting table on pages 26 27 for possible solutions If no solution can be found or an error code not listed is displayed then you should disconnect your appliance from the mains supply and contact customer service immediately quoting the error code FOR THE ABOVE FAULT CODES IF THE CODE REAPPEARS AFTER FOLLOWING THE ADVICE AND CLEARING THE FAULT CODE YOU SHOULD TURN OFF THE APPLIANCE DISCONNECT THE APPLIANCE FROM YOUR MAINS SUPPLY AND THEN ARRANGE FOR A SERVICE TECHNICIAN TO ATTEND THE APPLIANCE BY CONTACTING THE CUSTOMER SERVICE DEPARTMENT Please note that if a service technician is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault then you may be liable for the cost of the call out charge The appliance must be accessible for the service technician to perform any necessary repair If yo
Download Pdf Manuals
Related Search