Operating Manual for Orbital and Linear Digital Shaker
Contents
1. e The shaker shows desired speed and time after initialization e Turn the speed knob on to set the desired speed e Press the speed knob and characters on the left LCD stop flashing shaking begins e Press the speed knob again and characters begin to flash and the shaking function is switched OFF e Turn the time knob to set the desired time e Press the time knob and characters on the LCD stop flashing timing function begins e Press the time knob again and characters on the right LCD begin to flash and the timing function is switched OFF 5 2 1 Set Time The desired shaking time can be set by turning the time knob A distinction is made for the shaking time setting between Continuous Mode and Timed Mode If Continuous Mode is selected by pushing the speed knob the shaker can continue its shaking function for any amount of time with the previously set speed If Timed Mode is selected by selecting time and pushing the time knob the shaker can run in the set time After the shaker is powered OFF and restarted the set time is erased to zero and it switches into offline operating mode If a target time max 19h 59min and speed are set users can activate the shaker with pressing the time knob time operations begin by A Pressing the time knob the speed and time will stop Pressing the time knob again restarts the shake function the time will use the pre set time B Pressing the speed knob the speed and time will s2. Do not operate this unit unattended 3 Setup the shaker in a spacious area on a stable clean non slip dry and fireproof surface Do not operate the shaker in explosive atmospheres with hazardous substances or underwater 4 This shaker must be used with UL CSA certified power supply cord set Orbital and Linear Digital Shaker 10 11 Ensure that the operating voltage required as stated on the shaker and voltage in the supply network match Do not modify this unit or attach any accessory that is not included with the Orbital and Linear Digital Shaker or is not an accessory manufactured by BURRELL SCIENTIFIC LLC for this unit All BURRELL SCIENTIFIC LLC accessories for the Orbital and Linear Digital Shaker must be securely attached to the shaker and vessels must be firmly placed on the shaking table prior to use Inspect accessories for damage prior to use and always disconnect the power cord prior to attaching accessories Do not use the Orbital and Linear Digital Shaker if it or its accessories are damaged In all cases shake vessels with closures or rubber stoppers Caution should be taken when operating the shaker with heavy loads or at higher speeds where applicable Observe the vessel on the shaking table for liquid splashing out when setting the motor speed Reduce 12 13 14 15 16 17 18 motor speed if the shaker is not running smoothly If the procedure you are using involves gases or
3. creates a hazardous environment perform such testing in a properly ventilated fume hood Keep in mind that working with combustible or flammable materials may result in additional hazards Only process liquids that will not react dangerously to the extra energy produced through shaking If any spill occurs assure all liquids have been cleaned up in a safe manner and the area of operation is completely dry to avoid an electrical hazard Do not touch any moving parts of the shaker Do not cover the shaker Protect the shaker and accessories from bumps and impacts Keep away from high magnetic field Always disconnect plug when the shaker is not in use If you should encounter any problems with the installation or initial operations of this unit please contact us at 1 800 637 6074 Orbital and Linear Digital Shaker 3 UNPACKING YOUR SHAKER Listing of Items The packing includes the following items The basic shaking unit Power cord adapter with international orders only Operation Manual Dish Tray Top Platform Unpack the shaker carefully and check for any damages that may have occurred during shipment Should any damage occur in shipment do not operate and notify Burrell Scientific Customer Service department at 1 800 637 6074 Note If there is any apparent damage to the system please do not plug it into the power line 4 TRIAL RUN Prior to operating the shaker with vessels and liquids
4. for a period of 12 months from the date of invoice The warranty is extended only to the original purchaser Warranty will not apply to any product or parts which have been damaged on account of improper installation improper connections misuse accident or abnormal conditions of operations Shakers can only be returned after receiving a return authorization from Burrell Scientific LLC 11 Orbital and Linear Digital Shaker NOTES
5. Operating Manual for Orbital and Linear Digital Shaker By Burrell Scientific OPERATIONS MANUAL Linear Digital Shaker Orbital Digital Shaker Burrell Scientific LLC 300 Parkway View Drive BURRELL Pittsburgh PA 15205 412 747 2111 F 412 747 4927 email Please read the User Manual carefully before use and follow all operating and safety instructions Orbital and Linear Digital Shaker CONTENTS TD SPFO PC MUSC Ges cass ves vecsaxeusdetssnnvcsareasVetarrsetciaraasent cearceaarsened 1 7 Supported COAG ae iscssrvruscearcnondasurneasvavensadesvenedesveneniatndeess 8 2 Sale OPETE E O EAE E EA A teed 8 3 Unpacking s ssssssssssssstsssssrissssssrnssnnttensnnttnnnnntteenntteennnttent 3 9 interface hionann ice a A n ia 8 4 Trial RUM nenen cee aeie iaa 3 10 Maintenance and Cleaning c cscccsessesesseseessseseseeees 9 5 Control and SOtv2sss5 sesscceessazazesesesacesssadaseacsecacavaheducecusedaces 4 11 Associated Standards and Regulations ccsceseee 9 5 1 Control ose tsnensaessaeeeees 4 12 Specifications c253 scout races caeeats atari auntaemenn satan 10 A 5 TS Servite inira en inn alia ia 11 5 2 1 Set Time 5 12 Waa ciate t a et Bot aA 11 5 2 2 Setting Speed E EE 5 6 Operating Modes cccecesssccesssseceessseeeesssseeeesssseeeessnees 6 6 1 Mode Aus iccnienreniceenainiieisnanienanind 6 6 2 Mode lB vit niece teatet aids test ous al eels 7 6 3 Switching the MOde ccccccsssseceess
6. a Note The set values can be varied during shaking Shaking can be stopped by pressing the left or right knob Orbital and Linear Digital Shaker 6 3 Switching the Mode Switch the operating mode as follows e Turn OFF the shaker with the mains switch e Hold down both knobs and turn ON the shaker with the mains switch After 5 seconds let go of knobs e Switch between operating Modes A and B in order 7 SUPPORTED OPERATION e In order to ensure safe operations the shaker must only be operated within the supported weight limit e Make sure the holding surface of the shaker is always clean and level e Ensure the individual shaking vessels are placed evenly and fastened securely in the middle of the shaking table regardless of number of vessels being shaken one to multiple 8 FAULTS e When switched ON and the shaker doesn t work o Check whether the power cable is fully inserted o Check whether the fuse is broken e The speed cannot reach set value o Check whether it is overloaded e The motor does not start via pressing the speed knob and time knob o Check whether the time is set to zero 9 INTERFACE The Orbital and Linear Digital Shaker special adapter and cable are used to link to external device and the standard 9 pin interface to connect with a PC e The cable between the shaker and a computer use an EIA Standard RS232C communication line corresponding to the DIN 66020 interface e Tra
7. ed and time 160 2130 After pressing the speed knob or time knob the shaker begins to run at the set speed The actual speed and time remaining are shown in the LCD If the remaining has reached zero the shaker stops its motion Pressing the speed knob alone the shaker will work at Continuous Mode The time function is OFF Note The set values can be varied during shaking Shaking can be stopped by pressing the left or right knob Orbital and Linear Digital Shaker 6 2 Mode B When the shaker is turned ON and values for speed and time are erased to zero users can set the upper speed limit from Operating Mode A After the power has been turned OFF the shaker will no longer automatically start up in operating Mode B by itself After turning ON the shaker and selected run mode the following process will be shown on the display e The left LCD displays SAFE and the right displays the upper speed limit rpm which can only be changed during start up SATE 550 e The LCD displays run modes StA for 2 seconds StA b The set speed value is shown in the left display and the set time value is shown in the right display Then set the motor rotary speed and time 000 0 00 160 Wate ss After pressing the speed knob or time knob the shaker begins to run at the set speed The actual speed and time remaining are shown in the LCD If the remaining has reached zero the shaker stops its motion 160 A
8. it is important to perform a trial run operation to ensure the unit is working properly Perform this as follows e Make sure the required operating voltage and power supply voltage match 100 240 V 50 60 HZ Ensure the socket is securely earthed Plug in the power cable then power ON the shaker LCD displays the safe rotary speed limit LCD displays operating mode Turn the speed knob to set the rated rotary speed Press the speed knob and turn the shaking function switch to ON e Press the speed knob again and turn the shaking function switch to OFF If the mounting surface is not even you can improve the stability of the shaker with the adjustable feet To do this turn the appropriate foot downward with a wrench until the shaker is standing securely on the surface Orbital and Linear Digital Shaker 5 CONTROL AND SET 5 1 Control Items Description Set rated rotary speed rotation is Speed knob switched ON or OFF via pressing the knob Set working time rotation is switched ON Time knob or OFF via pressing the knob LCD Display the status of shaker and any set Mains switch Switch ON or OFF Shaking Table LCD Speed LCD Time Speed Knob Time Knob Orbital and Linear Digital Shaker 5 2 Set e Put the shaker on a stable and safe place Plug in the mains power e Turn ON the mains switch on the left panel e The shaker starts self test
9. nsmission method Asynchronous signal transmission e Mode of transmission Fully Duplex e 1start bit 8 character bits 1 stop bit e Transmission speed 9600 bit s Orbital and Linear Digital Shaker 10 MAINTENANCE AND CLEANING Only use these cleaning agents which have been approved by the manufacturer to clean the shaker e Switch the shaker to the OFF position and store in a dry clean and stable place at room temperature when not in use 11 ASSOCIATED STANDARDS AND REGULATIONS Construction in accordance with the following safety standards Dyes Isopropyl alcohol Construction Water containing mild detergent materials isopropyl alcohol Cosmetics Water containing mild detergent isopropyl alcohol Foodstuffs Water containing mild detergent Fuels Water containing mild detergent Please contact Burrell Scientific LLC prior to using any other cleaning or decontamination method to ascertain that this method will not destroy the shaker Wear the proper protective gloves during cleaning of the shaker Please Note e The shaker must not be placed in the cleaning agent for the purpose of cleaning Spot clean only e The shaker must be cleaned and put into the original packaging carton before sending out for service or repair EN 61010 1 UL 3101 1 CAN CSA C22 2 1010 1 EN 61010 2 10 Construction in accordance with the following EMC standards EN 61326 1 O
10. rbital and Linear Digital Shaker 12 SPECIFICATIONS Items Specifications Voltage VAC 100 240 Frequency Hz 50 60 Power W 30 Shaking Movement Orbital Linear Orbital Diameter mm 10 7 5 kg Max Shaking Weight with attachment 16 5 lbs 7 5 kg External rotor brushless Motor Type mtor Motor Rating Input W 28 Motor Rating Output W 15 Permissible ON Time 100 Speed Range rpm 100 350 Linear 100 500 Orbital 10 Items Specifications Speed Display LCD Timer Yes Timer Display LCD Time Setting Range min 1 1199 Run Type Time Continuous Operation Dimensions DxWxH mm 420 x 370 x 100 Shipping Weight 32 Ibs Permissible Ambient 5 40 Temperature C Permissible Relative ees 80 Humidity Protection Class Acc To DIN IP21 EN60529 RS232 interface Yes Orbital and Linear Digital Shaker SERVICE If assistance is needed please contact Burrell Scientific LLC for technical support Please provide the Customer Care Representative with the following information e Serial Number located on the rear panel e Certification e Description of problem i e hardware or software e Methods and procedures used to resolve the issue e Your contact information WARRANTY This shaker is warranted to be free from defects in materials and workmanship under normal use and service
11. seeeessseeeesees 8 Orbital and Linear Digital Shaker OPERATING INSTRUCTIONS WARNING Do not attempt to assemble connect to power source or operate the Orbital and Linear Digital Shaker without first reading these instructions Also assure that each person that will operate this unit becomes familiar with these operating instructions Shakers are CE approved and comply with UL CSA 61010 1 requirements comply with EN 61010 1 safety requirements and meet EN 61326 1 2006 electrical equipment for measurement control and laboratory use EMC requirements 1 PROPER USE The Orbital and Linear Digital Shaker is designed for mixing or shaking liquids in schools laboratories or factories The shaker is suitable for usage in various attachments for mixing liquids in bottles flasks test tubes for a maximum supported weight of 16 5 Ibs e Read the operating instructions completely e shaker Warning Ensure that only trained staff work with the protective ground contact before use 2 SAFE OPERATIONS before use and follow the safety instructions Protective ground contact e Make sure the socket must be earthed 1 When operating this unit always wear safety eye protection and suitable safety apparel for the material being shaken taking into account the possibility of splashing liquids vibration forces leading to a broken glass container and the inhalation of the body hair clothes and jewelry 2
12. top Pressing the speed knob again restarts the shake function flashing occurs on the LCD The time will use the pre set time Note The current set time can be varied at any time 5 2 2 Set Speed The desired speed and upper speed limit can be set by turning the speed knob The Continuous Mode can be switched ON with pressing the left knob without the time setting and switched OFF with pressing the knob again Orbital and Linear Digital Shaker Adjust the motor speed knob slowly in order to keep the shaker running smoothly Note The current set speed can be varied at any time 6 OPERATING MODES 6 1 Mode A Operating Mode A is the default mode set at factory After turning the shaker ON with the mains switch the shaking and timing functions are turned OFF The LCD displays the set time and speed values They are adopted or varied when the corresponding functions are turned ON After turning the shaker ON the following process will be shown on the display e The left LCD displays SAFE and the right displays the upper speed limit rpm which can be set by pressing the speed knob and turning at the same time SATE 550 The LCD displays run modes StA A or B for about 2 seconds STA bD The set or stored speed value is shown in the left display and the set or stored time value is shown in the right display Turn the speed knob and time knob can set the spe
Download Pdf Manuals
Related Search