User Manual 19" LCD Open frame SAW Touch Monitor KOT
Contents
1. Touch screen Type Ao 90 4B 19 SAW 4MM thickness of touch screen sensor Touch screen Touch sereen Type Available Options Thickness Anti glare T empered Touch System Interface Having USB and serial interface 10 1 LCD Open frame SAW Touch Monitor AKG Technology Inc htto www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A Touch Response time 9ms je an ii Agency Approval ETL FCC CE RoHS Regular Warranty 5 years for SAW Sensor 3 years for controller 1 year for LCD NOTE Our current LCD panel is made by one of the largest Chinese LCD panel manufacture BOE www boe com cn and SVA NEC www sva nec com english index html 11 11 LCD Open frame SAW Touch Monitor2. The screen is blank 1 During operation the monitor screen may automatically turn off as a result of the Power Saving feature Press any key to see if the screen reappears 2 Refer to the About Touch monitor Adjustments section to adjust the brightness Out of Range display Check to see if the resolution of your computer is higher than that of the LCD display Reconfigure the resolution of your computer to make it is less than or equal to 1024 xX 768 See Appendix A for more information on resolution Touch doesn t work Make sure the touch cable is securely attached at both ends Chapter 5 NATIVE RESOLUTION The native resolution of a monitor is the resolution level at which the LCD panel is designed to perform best For the LCD touch monitor the native resolution is 1280 x 1024 for the 19 inch size In almost all cases screen images look best when viewed at their native resolution You can lower the resolution setting of a monitor but not increase it The native resolution of an LCD is the actual number of pixels horizontally in the LCD by the number of pixels vertically in the LCD LCD resolution is usually represented by the following symbols 640 x 480 SVGA 800 x 600 1024 x 768 SXGA 1280 x 1024 UXGA 1600 x 1200 8 11 LCD Open frame SAW Touch Monitor AKG Technology Inc http www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M
3. AKG Technology Inc http www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A User Manual 19 LCD Open frame SAW Touch Monitor KOT 0190US SA4B Chapter 1 INtTrOGUCTION 0000s cccscsescsesesesesesesesesesesesesssescsescscsesessscsesesescssseseseseeees 1 1 Product Description 1 2 About the Product Chapter 2 Installation and Setup ccc csessssseseseseseseseeseseseeseseseteneeneeseeeen 2 1 Unpacking Your Touch monitor 2 2 Product Overview 2 3 VESA Mounting Interface 2 4 Attaching the L bracket 2 5 Interface Connection 2 6 Installing the Driver Software and Calibration 2 6 1 Installing the Driver Software 2 6 2 Calibration Jo af 1 ae Jam OPETI HON eee ee Pn mE ep rere errr eer 7 3 1 About Touch monitor Adjustments 3 1 1 Rear Panel Controls 3 2 Controls and Adjustment 3 2 1 On Screen Display OSD Menu Functions 3 2 2 Power Management System Chapter 4 Troubleshooting 0 0 ccc ccescsesesesesesesesesesesesesesesesesesesesesesesesesesesens 8 Chapter 5 Native Resolution ccccccccccssscsssssescsesesesesesescscscsesescsesssssssescecseeesesessaeass 8 Chapter 6 Touch monitor Safety siiscsciccccscsccrscnccnranuanhatvannmeniantunauccaiuanias 9 Chapter 7 Specification ccc cccsessescsssssssssssscscsesssssssssesseessseseseaesssssaseeeessseaeasatsnsnen 10 Chapter 1 INTRODUCTION 1 1 LCD Open frame S
4. AW Touch Monitor AKG Technology Inc http www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A ED wh i 1 1 Product Description KOT 0190US SA4B means KeeTouch s Open frame Touch monitor size is 19 with both USB and Serial RS232 interface integrates with Surface Acoustic wave touch screen and Dual USB RS232 controller 4 mm thickness glass of SAW touch screen panel this KOT 0O190US SA4B has a long lasting product cycle because the enclosure is controlled by KeeTouch s specifications Future panel improvements are therefore possible without external changes 1 2 About the Product Your LCD open frame touch monitor is a 19 SXGA TFT color display with the following features e Long lasting product cycle enclosure controlled by KeeTouch specifications e Future generation panels phased in without external changes e High quality panel with high brightness high contrast ratio and broad viewing angle e Multiple mounting options including VESA mount horizontal or vertical bracket mount e KeeTouch s SAW technology on pure glass for the ultimate in image quality e Finger or gloved hand operation e Dual USB Serial touch interface port e Worldwide agency approvals For full Product Specifications refer to Appendix C Chapter 2 INSTALLATION amp SETUP This chapter discusses how to install your LCD touch monitor and h
5. Alhambra CA 91803 U S A ED wh i As an example a SXGA resolution LCD panel has 1280 pixels horizontally by 1024 pixels vertically Input video is also represented by the same terms SXGA input video has a format of 1280 pixels horizontally by 1024 pixels vertically When the input pixels contained in the video input format match the native resolution of the panel there is a one to one correspondence of mapping of input video pixels to LCD pixels As an example the pixel in column 45 and row 26 of the input video is in column 45 and row 26 of the LCD For the case when the input video is at a lower resolution than the native resolution of the LCD the direct correspondence between the video pixels and the LCD pixels is lost The LCD controller can compute the correspondence between video pixels and LCD pixels using algorithms contained on its controller The accuracy of the algorithms determines the fidelity of conversion of video pixels to LCD pixels Poor fidelity conversion can result in artifacts in the LCD displayed image such as varying width characters Chapter 6 TOUCHVONITOR SAFETY This manual contains information that is important for the proper setup and maintenance of your touch monitor Before setting up and powering on your new touch monitor read through this manual especially Chapter 2 Installation and Chapter 3 Operation 1 To reduce the risk of electric shock follow all safety notices and never open the touch moni
6. driver installation Nn I j LCD Open frame SAW Touch Monitor AKG Technology Inc htto www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com 3 SE Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A UPDD Install This program will install the Sottware version 04 00 02 Universal Pointer Device Driver software on your computer USE controllers will be Supported controllers T N detected automatically by the e a a Series 2 install process and do not need W EceTouch ECA USE Series USB to be selected Serial gt EeeTouch ECT Series Serial controllers need to be selected rere now or after the software has been installed Click Install to proceed ur Cancel if OW da not wish i to install the software at this COMI time x Cancel gt Install 4 Calibration Find calibration from UPDD in All programs and complete the calibration for your touch system at the first time of touch system integration and every time you changed the touch screen sensor or controller Chapter 3 OPERATION 3 1 About Touch monitor Adjustments Your touch monitor will not likely require adjustment Variations in video output and application may require adjustments to your touch monitor to optimize the quality of the display For best performance your touch monitor should be operating in native resolution that is 1280 X 1024 at 80k 75 Hz U
7. he monitor more than 5mm 2 4 Attaching the L Brackets To attach the L brackets 1 Lay the monitor face down 2 Place the long end of the L bracket against the side of touch monitor Line up the two holes of the L bracket with the two holes of the touch monitor 3 Place two M4 screws in the holes and with the screwdriver screw them in to secure the bracket 4 Repeat steps 2 and 3 to attach the other L bracket to the other side of the touch monitor NOTE The way to attach the L brackets has two options See the illustration below Option 1 Option 2 L brackets to the left and right sides L brackets to the up and down sides 2 5 Interface Connection Note Before connecting the cables to your touch monitor and PC be sure that the computer and touch monitor are turned off Adapter Video Cable Serial Cable USB Cable 1 Connect one end of either the serial RS232 cable or the USB cable but not both to the rear side of the computer and the other end to the LCD monitor Tighten by turning the two thumb screws clockwise to ensure proper grounding USB cable does not have thumb screws 4 11 LCD Open frame SAW Touch Monitor AKG Technology Inc htto www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A ED ma i 2 Connect one end of the video cable to the rear side of computer and the other to the LCD monitor Tighten b
8. hnology Inc http www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A LCD Type 19 Active matrix TFT LCD 14 8 376 3mm x11 9 301mm idth 482mm J P i idth with bracket 472mm Monitor Dimensions Height 351mm Height with bracket 391mm Depth 47mm Suggested Resolution 1280x1024 1280x1024 at 60 75 Hz 1024x768 at 60 70 75 Hz Supported Resolution 800x600 at 60 72 75 Hz 640x480 at 60 72 75 Hz 640x400 at 70 Hz Support Colors 16 2M Support Colors 162M mmmn ees e Brightness Typical 5 Viewing Angle Typical at CR gt 10 ___Signalinput_ H V Separate Syno TTL Vi i I aeo gna input Mini D Sub 15 pin VGA Connector Frequency H V 30 80KHz 60 75Hz Type External brick Power Supply Input line voltage 100 240 VAC 50 60 Hz Output vo oec ren 12 volts at 4 amps max Operating Temp Storage Temp 20 60 C Environment Operating RH Operating RH 20 80 Storage RH 10 90 MTBF 50 000 Hours LCD Back light Life Typical 50 000 Hours Weight N W G W 5 8Kg 8 Kg Power Consumption 5OW Max 1 VESA 75mm and 100mm Mount Interface 2 Mount bracket horizontal or vertical Standard mount brackets are supplied Buttons AUTO POWER MENU OSD Control Function Brightness Contrast Ratio Auto adjust Phase Clock H V Location Languages Function Reset
9. ighted when selected 3 To quit the OSD screen at any time during the operation press the AUTO key NOTE If no Keys are pressed for a short time period the OSD automatically disappears 3 2 2 Power Management System The monitor 1s equipped with the power management function which automatically reduces the power consumption when not in use Power Mode Consumption On lt 40W Sleep lt 4W Off lt 2W We recommend switching the monitor off when it is not in use for a long time NOTE The monitor automatically goes through the Power Management System PMS steps when it is idle To activate the monitor press any key on the keyboard or move the mouse 7 11 LCD Open frame SAW Touch Monitor AKG Technology Inc http www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A ned ma i Chapter 4 TROUBLESHOOTING If you are experiencing trouble with your touch monitor refer to the following table If the problem persists please contact your local dealer or our service center Solutions to Common Problems The monitor does not respond 1 Check that the monitor s Power Switch is on after you turn on the system 2 Turn off the power and check the monitor s power cord and signal cable for proper connection Characters on the screen are dim Refer to the About Touch monitor Adjustments section to adjust the brightness
10. ow to install the driver software 2 1 Unpacking Your Touch monitor Check that the following 9 items are present and in good condition One Touch monitor 2 L brackets 4 x M4 Screws and Washers N I j LCD Open frame SAW Touch Monitor AKG Technology Inc http www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com 3 Mts Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A ee a ee One Video cable One Brick power supply One Driver software CD One Serial cable or One USB cable One Power cable US Canada 2 2 Product Overview Mechanical Dimensions unit in mm KOT 0190US SA4B 2 MA in left right up down side A A D a oO Z gt p M 2 3 VESA Mounting Interface Your touch monitor conforms to the VESA Flat Panel Monitor Physical Mounting Interface FPMPMITM Standard which defines a physical mounting interface for flat panel monitors and corresponding standards for flat panel monitor mounting devices such as wall and table arms Your monitor has standard VESA mounting holes on the rear of the unit The holes are 3 1 LCD Open frame SAW Touch Monitor AKG Technology Inc http www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A J P i spaced at 75mm and 100mm standard NOTE Do not penetrate the M4 screw into t
11. se the Display control panel in Windows to choose 1280 X 1024 resolution Operating in other resolutions will degrade video performance For further information please refer to Appendix A All control adjustments are automatically memorized This feature saves you from having to reset your choices every time you unplug or power your touch monitor off and on If there is a power failure your touch monitor settings will not default to the factory specifications 3 1 1 Rear Panel Controls l 2 34 5 6 Pot dl le e Oe AUTO POWER MEN 6 11 LCD Open frame SAW Touch Monitor AKG Technology Inc http www akgtech com Tele 909 967 5572 Fax 909 580 8228 Email engineer akgtech com Mailing Address 1225 Benito Avenue M Alhambra CA 91803 U S A ned wh i Control Function 1 AUTO adjust to an optimum image automatically 2 1 Enter brightness adjustment 2 Increase value of the adjustment item 3 Select item counter clockwise 3 Power LED 4 Power Switches the power of the monitor 5 7 1 Enter brightness adjustment 2 Decrease value of the adjustment item 3 Select item clockwise 6 Menu Display exits the On Screen Display OSD menus 3 2 Controls and Adjustment 3 2 1 On Screen Display OSD Menu Functions To Display and Select the OSD Functions 1 Press the Menu key to activate the OSD menu 2 Use or to move through the menu Press the Menu key the parameter will be highl
12. tor case 2 Turn off the product before cleaning 3 The socket outlet shall be installed near the equipment and shall be easily accessible 4 The slots located on the sides and top of the touch monitor case are for ventilation Do not block or insert anything inside the ventilation slots 5 Itis important that your touch monitor remains dry Do not pour liquid into or onto your touch monitor If your touch monitor becomes wet do not attempt to repair it yourself Care and Handling of Your Touch monitor The following tips will help keep your touch monitor functioning at the optimal level e To avoid risk of electric shock do not disassemble the brick supply or display unit cabinet The unit is not user serviceable Remember to unplug the display unit from the power outlet before cleaning e Do not use alcohol methyl ethyl or isopropyl or any strong dissolvent Do not use thinner or benzene abrasive cleaners or compressed air e To clean the display unit cabinet use a cloth lightly dampened with a mild detergent e Avoid getting liquids inside your touch monitor If liquid does get inside have a qualified service technician check it before you power it on again e To clean the touch screen use window or glass cleaner Put the cleaner on the rag and wipe the touch screen Never apply the cleaner directly on the touch screen Chapter 7 TECHNICAL SPECIFICATIONS Model No KOT 0190US SA4B 9 11 LCD Open frame SAW Touch Monitor AKG Tec
13. y turning the two thumb screws clockwise to ensure proper grounding 3 Connect one end of the power adapter to the monitor and the other end to the connector of the power cord 4 Press the power button on the rear panel to turn the monitor power on NOTE The touch monitor should be integrated according to the above process if not may result in the touch monitor working abnormally 2 6 Installing the Driver Software and Calibration 2 6 1 Drivers can be downloaded from KeeTouch Driver CD developed by Touch base Windows 2000 for both home version amp professional version Windows XP for both home version amp professional version Windows Vista for both home version amp professional version 2 6 2 Drivers Supply from Technical Support email developed by KeeTouch e Windows XP embedded e Linux Your KeeTouch touch monitor is Plug and Play compliant Information on the video capabilities of your touch monitor is sent to your video display adapter when Windows starts If Windows detects your touch monitor follow the instructions on the screen to install a generic Plug and Play monitor 2 6 3 Installing the Driver Software Driver installation and Touch System calibration guide 1 Preparation connecting SAW touch screen controller and application device or computer with correct cable on the integration procedure 2 Insert the Kee Touch Driver CD in to application system 3 Follow the instruction to complete the
Download Pdf Manuals
Related Search