User guide for gauss meter TM192 & TM192D
Contents
1. o Press key turn on the meter press key again to turn OFF the meter a i Press key to select milli gauss mG or micro tesla uT unit Position the front of the meter to measure the electromagnetic waves Read the measured value When manual range select mode LCD will shown the mark The display of OL on the highest position indicates there is an overload on the reading Press Perge to select a higher range for measurement again This meter displays the default value is triaxial total magnetic field reading press key to independent three single axis magnetic field readings and triaxial total magnetic field reading To permanently lock and keep the reading displayed on the LCD press 2 or press La again to unlock key and the reading value displayed on the LCD will keep updating to the maximum value Press again to select minimum value press and hold down key 2 seconds to exit the maximum and minimum mode Due to the magnetic interference oi ihe environment field factors this magnetic field meter could dispiay a reading value that is lower than 0 5mG prior to measuring This is not a malfunction of the tester With the tester in hand move slowly towards to the object under measurement until it is physically touched Notice how the field intensity increases as you move closer to the object If the power of object was turned off during the measurement the reading of2. a soft dry cloth Never use a wet cloth solvents or water etc Operation Altitude Up to 2000M Operating Environment Indoors use This instrument has been designed for being used in an environment of pollution degree 2 oftware installation 192D Please put the CD in the PC that will be connected to this meter Please select the USB driver that will be installed such as E TM 192D PL 2303 Driver Installer exe windows 2000 SP4 windows XP SP2 click twice on the left key of the mouse to install the USB driver Select the SETUP EXE i e E TM 192D SETUP EXE and installs the desktop icon Tack out the CD from PC after completed the installation of the desktop icon Use the USB cable to connect the meter and computer according to the drawing Select the desktop icon TM 192 and click twice on left key of the mouse to run the procedure 18Note Caution this symbol indicates that equipment and its accessories shall be subject to a separate collection and correct disposal
3. tester should return to zero unless there is the electromagnetic from other sources are detected e Press o Press 6 Clock setup e This meter clock to introduce 24 hour time key to clock setting made ike FE Or gOHHYe YY MO DD KH MM key to select option to adjust key to change the digit key to store the setup exit the mode 7 Auto power off setup e gt MM key to change the auto power off Press J key to store the setup exit the mode This meter the auto power off time default value is 5 minutes for cancellation auto power off please set time as OOMM 8 Continuity data logging setup Press key again to continue data logging interva setting mode 3 SET i CE ICL 000000 REC 9 Clear data logger memory Press key again to clear data logger memory for last record setting mode 4 SET a Press 2s key to clear data logger memory for last record e Press key to clear data logger memory for last record and exit the mode 10Clear all data logger memory o Press key again to clear data logger memory for all record setting mode 5 SET roi ALl key to clear data logger memory for all e Press record o Press key to store the setup exit the mode 11 Single data memory e Press and memory location in memory 12Viewing logged reading control key Press Wis de or V key
4. to scroll through the readings aw key to exit this mode key each time to store the display reading key to view logged readings mode Press 13Specifications Display 4 digits Triple LCD display Range 20 200 2000 mG 2 20 200uT Resolution 0 01 0 1 1 mG or 0 001 0 01 0 1 uT Frequency response 30Hz to 2000Hz Sensor Triple Axis X Y Z re 20 mG 2uT 3 0 30dgt at 50Hz 60Hz 2 5 5dgt at 50HZ 60Hz 5 5dgt at 30HzZ 2000Hz Over load LCD display OL Sample rate 2 5 times per second Battery 9V NEDA 1604 IEC 6F22 or JIS 006P Battery life Approximate 100 hours Operating temperature amp humidity 5 Cto 40 C below 80 RH Storage temperature amp humidity 10 C to 60 C below 70 Weight About 230g Dimensions 173 L 80 W 32 H mm Accessories Users manual 9V battery Carrying case MINI USB 4P MALE to USB A Type cable CD disk 192D 14Baitery replacement Jif the symbol appears on the LCD please replace the battery immediatel Turn off the instrument Open the battery cover and remove the battery Replace with four 9V NEDA 1604 IEC 6F22 or JIS 006P size battery Install the battery cover 15External DC Power External AC to DC adapter Voltage 9Voc 8 14VpcMax Supply current gt 300mApce Socket pin Positive Ground Casing External Diameter 6 3mm internal Diameter 2 0 mm 16S 1738 afety Precaution For cleaning the instrument use
5. 1 Introduction Safety precautions should be taken against electric appliances in places including medical institutions schools and residential districts where people usually stay for a lorig time to prevent patients babies and senior citizens from exposure to high electromagnetic waves An electromagnetic wave simply means the wave motion of the electromagnetic field EMF The change in electric fields produces magnetic fields and the change in magnetic fields can also generate electric fields The fluctuation of correlation between each other is known as electromagnetic waves which is a form of energy similar to light and heat that can be transmitted either by radiation in the air or by an electric conductor it is suggested that rearrangements should be made in families and work locations where electromagnetic fields are detected the strongest in order to avoid prolonged exposure to excessive electromagnetic fields Application This meter is applied to measuring electromagnetic fields of extremely low frequency ELF of 30 to 2000Hz e It is capable of measuring the electromagnetic field radiation intensity that is produced from electric transmission equipment power line microwave oven air conditioner refrigerator computer monitor video audio device and so forth The magnetic field unit is Tesla T Gauss G milli Gauss mG or micro Tesla u T o 1 T 10 000 G e 1 G 1 000 mG 1g T 10 mG 3 Features e Uses
6. three internal orthogonal sensors to test a wide range of ELF magnetic fields independent of measurement angle la The tester is designed to provide user a quick reliable and easy way to measure magnetic field radiation levels around power lines home appliances and industrial devices e The tester is a cost effective hand held instrument that was designed and calibrated to measure magnetic field radiation at different bandwidths from 30HZ to 2000HZ Display micro Tesla u T or milli Gauss m G units e Data hold HOLD gt maximum go diag abe minimum Hold MIN function Auto range or manual range select Mode Datalogging capacity with Memory Size 500 data sets or 9999 data sets 192D USB PC interface 192D Time and calendar function Low battery indication EA Over load display OL Auto power OFF function 4 identifying Paris e LSE TIC a i G amp e aan amp LCD display Power key maximum Hold and minimum Hold key Data Hold key Record dada and Setup function left key 6 Range and Setup function up key 7 Reading and Setup function right key 8 Setup function key 9 Units and Setup function down key 10 Ent r key 11 Calibrate point for Triple axis 12 External power DC 9V 13 USB interface TM 192D 14 Tripod mounting screw 15 Battery cover Wh an e e Measurement Procedures
Download Pdf Manuals
Related Search