SAS to SAS/SATA JBOD Subsystem User Manual
Contents
1. computer system 2 3 2 Connecting to RAI D Subsystem Attach one end of the SAS cable to the SAS IN Port of the JBOD controller module and the other end to the SAS Expansion Port on the RAID controller of RAID subsystem If configured in redundant mode connect the other SAS cable to the SAS IN Port of the other JBOD controller and the other end to the SAS Expansion Port on the other RAID controller of RAID subsystem User Manual 23 SAS to SAS SATA J BOD Subsystem Chapter 3 Maintenance 3 1 Upgrading Firmware Upgrading Firmware Trough Terminal NOTE It is important to stop I O access to J BOD subsystem during a firmware upgrade NOTE Upgrading the firmware must be done from Master J BOD Controller if the J BOD Subsystem has redundant J BOD Controllers 1 Please use the null modem cable RJ 11 to DB9 and to connect J BOD Monitor Port and PC COM1 Port or change to other COM Port as necessary 2 Open Windows HyperTerminal Program Connect using COM1 COM Port used in Step1 Baud Rate 115200 n 8 1 Flow Control None 3 Press the Enter key and the password prompt will be displayed 4 Key in the password Default password 00000000 to login to CLI 5 At CLI prompt input the command to update firmware a CLI gt fdi code O NOTE fdl code 0 is the command to update flash firmware code fw file fdl mfgb 0O is the command to update CFG data code rom file Make sure you have both files befo2. operate and cool the enclosure When the power cord connected from main power source is inserted to the AC Power Inlet the power status LED becomes RED When the switch of the PSFM is turned on the LED will turn GREEN When the Power On Fail LED is GREEN the PSFM is functioning normally 10 User Manual SAS to SAS SATA J BOD Subsystem NOTE Each PSFM has one Power Supply and two Fans PSFM 1 has Power l Fan 1 and Fan 2 The PSFM 2 has Power 2 Fan 3 and Fan 4 When the Power Supply of a PSFM fails the PSFM need not be removed from the slot if replacement is not yet available The fan will still work and provide necessary airflow inside the enclosure In replacing the failed PSFM refer to section 3 2 2 of this manual NOTE After replacing the Power Supply Fan Module and turning on the Power On Off Switch of the PSFM the Power Supply will not power on immediately The Fans in the PSFM will spin up until the RPM becomes stable When Fan RPM is already stable the RAID controller will then power on the Power Supply This process takes more or less 30 seconds This safety measure helps prevent possible Power Supply overheating when the Fans cannot work User Manual ql SAS to SAS SATA J BOD Subsystem 1 6 LCD Display Panel 1 6 1 LCD Panel LED Power LED Power Fail LED Fan Fail LED Over Temperature LED Voltage Warning LED Reserved for RAID Subsystem Power LED Green indicates power is ON Pow
3. 16 bays J BOD Subsystem The JBOD subsystem is a 19 inch 3U 16 bays rackmount JBOD unit It features the latest SASII 6Gb s interface and designed to fit in with the environments which needed highly reliable and relentless data growth The JBOD subsystem is also a versatile SAS SATA Disk Expansion system ideal for high capacity and scalability storage in IT demands Based on the 6G SAS technology the JBOD subsystem supports the choice of SAS and SATA drive configurations to deliver the best cost performance index with higher bandwidth User Manual aoo SAS to SAS SATA J BOD Subsystem 1 1 Features 16 hot swappable drive bays in a rackmount 3U chassis Simultaneously support SAS or SATA disk Single or dual SAS JBOD controller module Each SAS JBOD controller module has three mini SAS 4X ports Power Supply and cooling system contained in 1 module for efficient cooling Two 500W redundant hot swappable power supplies Incorporates a cableless design for maximum signal integrity Utilizes industry standard SCSI Enclosure Services to monitor enclosure and disk environmental conditions Enclosure Monitoring S E S support for standard enclosure management System LED indications Fan speed monitoring Power supply monitoring System voltage monitoring System temperature monitoring System alarm a User Manual SAS to SAS SATA J BOD Subsystem 1 2 Technical Specifications RAID Controller Controller Single Redunda
4. Lock Indicator sessenta Eee EE E EEEE 15 Chapter 2 Installation of J BOD Subsystem ssssssscccceccccessssssseccceeeees 16 AE PON Oee E AT 16 Z2 Disk Dive MAANA ierte r e e NE E E ere Ce EEN 17 2 2 1 Installing a SAS Disk Drive in a Disk Tray csessssesssessesessscsssesessssesesessssesesessesessssesesessesssessseesseseesees 17 2 2 2 Installing a SATA Disk Drive Dual JBOD Controller Mode in a Disk Tray sees 20 23 Connecting the JBOD oy 8 0 35 0 9 9 Renee ee Rene reer Never ee ae a TEST ote ne ene Cem ne 23 RSL Connecting O SAS HDA ee aero nee et ec em e are vee em er ee ee 23 232 Connecting to RAID SUD Sy St CIV s esiet ieee aeee eeoa eea EN to re AUEN 23 Chapter 3 Maintenance oooeeeeeeeceesssssssssscccscccccceeeeeeseeesssssccccccceeeeeeeseessssssssssseeceeee 24 sA UD n A O e E E E ANS 24 3 2 Replacing JBOD Subsystem COMPONENMS cccesessesesesessesssesessesessseessscsessssesssnssesesessesssesssescseseeseseeesesseseees 26 3 2 1 Replacing JBOD Controller Module ss ssnnssoessesesseesssesssesssesssesssenssenssenserensssnsennsennsennsenssenssenssenssenssenssens 26 3 2 2 Replacing Power Supply Fan MOdUule nu cccsesesssssssesssscsssssscssssssssssssssessssesessssssessssesesessssssesesessesseesees 21 3 2 2 1 Replacing Power Supply Fan Module with Plate COVES cccsessseesesesesseseeeseeeseeeeeesesteen 28 0O a User Manual SAS to SAS SATA J BOD Subsystem Chapter 1 Introduction The
5. SAS to SAS SATA J BOD Subsystem User Manual SAS to SAS SATA J BOD Subsystem Table of Contents Chapter 1 Introduction ooooooeeeeeeeseesssssssssscccccccceeeeeeeeesssssecscocccceeeseeesesessssssssseeceeeeee 3 LE POO oa E E E A A E E EE 4 12 Technical SO SGI a ONG scenene ae Ea E secgteseote estos onentpidasalicbepseeotees 5 13 Unpacking The JBOD SUDSYSTEI xs cccsccestescsceencsbcecsaccecsestaasne rA e S Ae e E AATETTA aes 6 1 4 Identifying Parts of the JBOD Subsystem Qu ec sessssessesesessesesssscsscsesessesecsssescesessssessssesessssesecseacssesesnsseeeeneans 7 TA SON NOW teats etc tect cca csc ec ce gece eee ce ence E E estates 7 TAZ RAM VON occ etc E E tacs tpt tes ees atansssstsesset ere cuices te eesti aceessectese sebueate requ ea ssatarsen teeteteeeeaoeeeeenesee 8 14 gt JBOD C NTONEr MOGUC aera einen emer fo nas mn earner Tei er veteran ten eee ee 9 A JBOD Controler PF Atv Ua zecettscezesepe sec ecaccetssneetccecec aiaro TEE EE EE E EE PTEE a E ANER ETENE 9 L5 Power Supply Fan Module CS ae citereese wae eee ce accis ca cececes ste gcenbsctt s naaraana a iNi a sarre ence ee ete 10 EL PORNP NO eE op nnceceue tensa tt cen exec E E E 10 IRo 8 SB DD Ee E E A A E E A A ete ee E Fret ner Sere 12 LOL ECP Pane cl B eae A E E A E E E 12 t62 LCD Panel F unction BUTTONS rsisi ae E ea rE 13 I7 Pe eg og MOU eeen erates te ek ern A E E E EEA 14 t71 Disk Drive Stat s IndicatolS sestiere eee ed a E seus a R r 14 172 DrveCarnmer
6. SFM Use the handle to pull out the defective PSFM Before inserting the new PSFM make sure the Power On Off Switch is on Off state A a E 6 Insert and slide the new PSFM in until it clicks into place fails and the replacement Power Supply module is not yet available the failed Power Supply Module can be replaced with the Plate Cover This is to maintain proper airflow within the enclosure Refer to next section IMPORTANT When the subsystem is online and a Power Supply When replacing a failed component online it is not recommended to remove the failed component for a long period of time proper air flow within the enclosure might fail causing high controller disk drive temperature 7 Connect the power cord to the AC Inlet Plug of PSFM 8 Tighten the thumbscrews of the PSFM 9 Turn on the Power On Off Switch of the PSFM NOTE After replacing the Power Supply Fan Module and turning on the Power On Off Switch of the PSFM the Power Supply will not power on immediately The Fans in the PSFM will spin up until the RPM becomes stable When Fan RPM is already stable the RAI D controller will then power on the Power Supply This process takes more or less 30 seconds This safety measure helps prevent possible Power Supply overheating when the Fans cannot work User Manual 7A SAS to SAS SATA J BOD Subsystem 3 2 2 1 Replacing Power Supply Fan Module with Plate Cover When replacing a failed power supply fan m
7. and to verify J BOD firmware version CLI gt sys i If needed the reset command can also be used to restart the J BOD controller Normally used in single JBOD Controller mode If already to connect to Controller CLI gt reset User Manual 25 SAS to SAS SATA J BOD Subsystem 3 2 Replacing J BOD Subsystem Components 3 2 1 Replacing J BOD Controller Module When replacing a failed JBOD Controller Module please follow these steps Loosen the thumbscrews on the sides of the JBOD Controller Module drawer 2 Use the Controller handle to pull out the defective JBOD Controller Module drawer 3 Insert and slide the new JBOD Controller Module in Note that it may be necessary to remove the old defective JBOD Controller Module from the drawer case and install the new one IMPORTANT When replacing a failed component online it is not recommended to remove the failed component for a long period of time proper air flow within the enclosure might fail causing high controller disk drive temperature 4 Tighten the thumbscrews on the sides of the JBOD Controller Module case fs o Ea AA 380 P i n 26 User Manual SAS to SAS SATA J BOD Subsystem 3 2 2 Replacing Power Supply Fan Module When replacing a failed power supply fan module PSFM please follow these steps Turn off the Power On Off Switch of the failed PSFM Disconnect the power cord from the AC Inlet Plug of PSFM Loosen thumbscrews of the P
8. e the subsystem is running 2 2 1 Installing a SAS Disk Drive in a Disk Tray NOTE These steps are the same when installing SATA disk drive in Single Controller Mode 1 Unlock the Disk Trays using a flat head screw driver by rotating the Lock Groove Disk Tray is unlocked Tray Open Button 3 Pull out an empty disk tray User Manual ETA SAS to SAS SATA J BOD Subsystem 4 Place the hard drive in the disk tray Turn the disk tray upside down Align the four screw holes of the SAS disk drive in the four Hole A of the disk tray To secure the disk drive into the disk tray tighten four screws on these holes of the disk tray Note in the picture below where the screws should be placed in the disk tray holes Tray Hole A NOTE All the disk tray holes are labelled accordingly 18 User Manual SAS to SAS SATA J BOD Subsystem 5 Slide the tray into a slot 6 Press the lever in until you hear the latch click into place The HDD Fault LED will turn green when the subsystem is powered on and HDD is good 7 If necessary lock the Disk Tray by turning the Lock Groove User Manual 19 SAS to SAS SATA J BOD Subsystem 2 2 2 Installing a SATA Disk Drive Dual J BOD Controller Mode ina Disk Tray 1 Remove an empty disk tray from the subsystem im aka Re pa ARELA ua aT O ete 0 yi e Pza in e d TE 3 Place the dongle board in the disk tray Turn the tray u
9. efinition ry User Manual SAS to SAS SATA J BOD Subsystem 1 7 2 Drive Carrier Lock Indicator Every Drive Carrier is lockable and is fitted with a lock indicator to indicate whether or not the carrier is locked into the chassis or not Each carrier is also fitted with an ergonomic handle for easy carrier removal Drive Carrier is unlocked Drive Carrier is locked When the Lock Groove is horizontal this indicates that the Drive Carrier is locked Lock and unlock the Drive Carriers by using a flat head screw driver User Manual a5 SAS to SAS SATA J BOD Subsystem Chapter 2 Installation of J BOD Subsystem 2 1 Powering On 1 Plug in the power cords into the AC Power Input Socket located at the rear of the subsystem Power On Off Switch n Caan rae Coe e EO VARNING Sere none AC Power Input Socket NOTE The subsystem is equipped with redundant full range power supplies with PFC power factor correction The system will automatically select voltage 2 Turn on each Power On Off Switch to power on the subsystem 3 The Power LED on the front panel will turn green 16 User Manual SAS to SAS SATA J BOD Subsystem 2 2 Disk Drive Installation This section describes the physical locations of the hard drives supported by the Subsystem and give instructions on installing a hard drive The subsystem Supports hot swapping allowing you to install or replace a hard drive whil
10. er Fail LED Fan Fail LED Over Temperature LED Voltage Warning LED If one of the redundant power supply unit fails this LED will turn to RED and alarm will sound Turn RED when fan 1 or 2 fails or speed is lower than 500 RPM If disk temperatures exceed 60 C the Over Temperature LED will turn RED and alarm will sound An alarm will sound if detected voltage in the controller is abnormal and LED will turn RED ary User Manual SAS to SAS SATA J BOD Subsystem 1 6 2 LCD Panel Function Buttons Up and Down Use the Up or Down arrow keys to go through the information on the OM BUTTONS hd LCD screen This is also used to move between each menu A This is used to enter the option Select button you have selected l Press this button to return to the User Manual 13 SAS to SAS SATA J BOD Subsystem 1 7 Drive Carrier Module The Drive Carrier Module houses a 3 5 inch hard disk drive It is designed for maximum airflow and incorporates a carrier locking mechanism to prevent unauthorized access to the HDD 1 7 1 Disk Drive Status I ndicators Disk Activity _ Indicator Disk Status Indicator This LED will blink blue when the hard drive is being Disk Activity Indicator accessed Green LED indicates power is on and hard drive status is good for this slot If there is no hard drive the LED is Disk Status Indicator Red The fault indicator depends on the RAID card or RAID Controller d
11. nt mwee SSS Tray Lock Disk Status I ndicator Access Fail LED Power LED Power requirements AC 90V 264V Full Range 10A 5A 47Hz 63Hz Physical Dimension 590 L x 482 W x 131 H mm Request optional dongle board for SATA I III hard drive User Manual 5S SAS to SAS SATA J BOD Subsystem 1 3 Unpacking the J BOD Subsystem The shipping package contains the following JBOD Subsystem Unit Two 2 power cords One serial cable RJ 11 to DB9 Note Two serial cables for dual J BOD controllers One external Mini SAS cable SFF 8088 to SFF 8088 Note Two mini SAS cables for dual J BOD controllers One 1 JBOD Controller Module Plate Cover NOTE For Dual RAID Controller One 1 PSFM Plate Cover User Manual 6 User Manual SAS to SAS SATA J BOD Subsystem 1 4 Identifying Parts of the J BOD Subsystem The illustrations below identify the various parts of the expansion chassis 1 4 1 Front View Smart LCD Panel Drive Carriers Slot 4 Slot 3 Slot 2 Slot 1_ Slot 8 Slot 7 Slot 6 Slot 5 Slot 12 Slot 11 Slot 10 Slot9 Slot 16 Slot 15 Slot 14 Slot 13 User Manual Ea SAS to SAS SATA J BOD Subsystem 1 4 2 Rear View Dual J BOD Controller JBOD Controller 1 JBOD Controller 2 Power Supply Power Supply Fan Module 1 Fan Module 2 Single J BOD Controller Controller Module Power Supply Power Supply Fan Mod
12. odule PSFM with Plate Cover please follow these steps Turn off the Power On Off Switch of the failed PSFM Disconnect the power cord from the AC Inlet Plug of PSFM Loosen thumbscrews of the failed PSFM Pull out the defective PSFM Insert the PSFM Plate Cover carefully Se A a ar User Manual
13. pside down Align the two screw hole of the dongle board in the two Hole D of the disk tray Tighten two screws to secure the dongle board into the disk tray 20 User Manual SAS to SAS SATA J BOD Subsystem Tray Hole D NOTE All the disk tray holes are labelled accordingly 4 Place the SATA disk drive into the disk tray Slide the disk drive towards the dongle board User Manual 2i SAS to SAS SATA J BOD Subsystem 5 Turn the disk tray upside down Align the four screw holes of the SATA disk drive in the four Hole C of the disk tray To secure the disk drive into the disk tray tighten four screws on these holes of the disk tray Note in the picture below where the screws should be placed in the disk tray holes pocmeeeee eee Tray Hole C BEB BBB BBP RB BRP NOTE All the disk tray holes are labelled accordingly 6 Insert the disk tray into the subsystem ees User Manual SAS to SAS SATA J BOD Subsystem 2 3 Connecting the J BOD Subsystem 2 3 1 Connecting to SAS HBA The Enclosure supports SAS interface which provides fast 300MB data transfer rate using SAS phy The package comes with one SAS cable for single JBOD controller module or two SAS cables for redundant J BOD controller modules Attach one end of the SAS cable to the SAS IN Port and the other end to the host bus adapter s HBA external SAS connector or to the SAS Switch The host bus adapter is installed in your Host
14. re updating b CLI gt fdl mfgb O Please Use XModem Protocol for File Transmission Use Q or g to quit Download before starting XModem Offset 0x0 cC Select Function menu to transfer CFG data rom file Function gt Transfer gt Send File gt Browse gt Open and select the rom file for example 8016 mfgdat6 20110131 rom firmware folder location Select Xmodem Protocol to send firmware file Only need about 60 seconds to finish sending firmware file If not please repeat steps B and D again Note If won t to transfer CFG data rom file Press Q or q to quit Download before starting data transfer 24 User Manual SAS to SAS SATA J BOD Subsystem d CLI gt fdl code O Please Use XModem Protocol for File Transmission Use Q or g to quit Download before starting XModem Offset 0x0 e Select Function menu to transfer firmware file Function gt Transfer gt Send File gt Browse gt Open and select the fw file for example 8016 07 01 09 96 20110211 fw from firmware folder location Select Xmodem Protocol to send firmware file Only need about 60 seconds to finish sending firmware file If not please repeat steps D and E again Note If won t to transfer firmware data fw file Press Q or q to quit Download before starting data transfer f Use reset command to Restart JBOD or power cycle g Re login to JBOD CLI h Use sys comm
15. ule 1 Fan Module 2 O B User Manual SAS to SAS SATA J BOD Subsystem 1 4 3 JBOD Controller Module 1 4 3 1 JBOD Controller Panel SAS Expansion Ports D a r oe a 8 8 8 f 8 Link LED i Bs a a a ae e e a e Activity LED eo MA E e o SAS In Port RS 232 Port Use to connect to SAS HBA or to RAID subsystem s SAS Expansion Port SAS Expansion Port Use to connect to the SAS In Port of another P JBOD subsystem Use to upgrade the firmware of the J BOD controller Connect the RJ 11 to DB9 serial cable to your system s serial port LinkLeD Green I ndicates expander has connected or linked Activity LED Blinking I ndicates the expander is busy and being Blue accessed User Manual so SAS to SAS SATA J BOD Subsystem 1 5 Power Supply Fan Module PSFM The JBOD subsystem contains two 500W Power Supply Fan Modules All PSFMs are inserted into the rear of the chassis 1 5 1 PSFM Panel Power On Fail Indicator Power On Off Switch AC Power Inlet Plug Male 4 2 lt 4 The panel of the Power Supply Fan Module contains the Power On Off Switch the AC Inlet Plug and a Power On Fail Indicator showing the Power Status LED indicating ready or fail Each fan within a PSFM is powered independently of the power supply within the same PSFM So if the power supply of a PSFM fails the fan associated with that PSFM will continue to
Download Pdf Manuals
Related Search