IntelliTrac X Series Protocol Document
Contents
1. 2003 Systems amp Technology Corp All rights reserved 12 i I IntelliTrac IntelliTrac X Series Protocol Document by S amp T 5 5 LED Indicators Function Off Power off 90 ms On 2 secs Off The device is running in power saving mode 500ms On 500ms Off Reset procedure is in progress On Power on Off The GPS is off or running in power saving mode 1 sec On 1 sec Off No GPS satellites signal received On GPS Ready Off The device is off or running in power saving mode 600 ms On 600ms Off No SIM card inserted or no PIN entered or network search in progress or network login in progress 90 ms On 3 secs Off Logged to network No call in progress 90 ms blinking 2 times GPRS Network connected 3secs On Voice Data call connected Off The device is ready On The device is not ready Blinking Please contact S amp T technical support team ST 2003 Systems amp Technology Corp All rights reserved 3 YT mtelirrac IntelliTrac X Series Protocol Document by S amp 5 6 About Systems amp Technology Corporation IntelliTrac X Series AVL device is produced by Systems amp Technology Corporation The company is a key developer and supplier of advanced systems in the Automatic Vehicle Location AVL Digital Map and Car Navigation Systems If you need information on other maps solutions or products please contact us at the phone and fax numbers listed below or visit our web site2. For query unit parameters Write Command Response OK MILEAGESET Read Command Response MILEAGESET Mode Frequency ST MILEAGESET 0000 0000 0 1 OK MILEAGESET ST MILEAGESET 0000 MILEAGESET 0 1 SSS TE 2003 Systems amp Technology Corp All rights reserved 8 F T Intelli Trac IntelliTrac X Series Protocol Document 5 Appendices 5 1 Report ID Description Report ID Description Remark 0 Position 1 Log position 2 Track position 3 Timer report position 4 Mileage report position 5 Wrong password access report position 6 ACC Off report position 7 Immobilized report position 8 Speeding report position 9 Towed report position 11 Input1 changed report position 12 Input2 changed report position 13 Input3 changed report position 14 Input4 changed report position 15 Input5 changed report position 16 Input6 changed report position 17 Input7 changed report position 18 Input8 changed report position 40 Main power low report position 41 Main power lose report position 100 119 User defined report position 5 2 STD Errors Description Error Code Description Unknown error Base phone number not set Unacceptable Incoming message Unsupported DCS format Outgoing voice call limited Voice call busy Voice call not connected No Incoming voice call Unsupported Report action GPRS configuration error Base station network error or GPRS communication error GPRS TCP resend failure or TCP pac
3. IntelliTrac X Series Protocol Document Version 2 1 TA version Date September 30 2004 Status Preliminary 2003 Systems amp Technology Corp All rights reserved General notes With respect to any damages arising in operation with the described product or this document S amp T shall be liable according to the General Conditions on which the delivery of the described product and this document are based This product is not intended for use in life support appliances devices or systems where a malfunction of the product can reasonably be expected to result in personal injury S amp T customers using or selling this product for use in such applications do so at their own risk and agree to fully indemnify S amp T for any damages resulting from illegal use or resale Information in this document is subject to change without notice at any time Copyright notice Copying of this document and giving it to others and the use or communication of the contents thereof are forbidden without express authority Offenders are liable to the payment of damages Copyright Systems amp Technology Corp 2003 All rights reserved 2003 Systems amp Technology Corp All rights reserved x ia g I Intellil rac IntelliTrac X Series Protocol Document by S amp T Table Of Contents Introduction To IntelliTrac X Series Protocol TA version e eeeee eene eene 1 2 Version History a
4. Command error 176 TPDU not supported 192 SC busy 193 No SC subscription 194 SC system failure 195 Invalid SME address 196 Destination SME barred 197 SM Rejected Duplicate SM 198 TP VPF not supported 199 TP VP not supported 208 DO SIM SMS storage full 209 No SMS storage capability in SIM 210 Error in MS 211 Memory Capacity Exceeded 212 SIM Application Toolkit Busy 213 SIM data download error 255 Unspecified error cause 2003 Systems amp Technology Corp All rights reserved ll F T Intelli Trac IntelliTrac X Series Protocol Document 300 301 302 303 304 305 310 311 312 313 314 315 316 317 318 320 321 322 330 331 332 340 500 512 513 514 515 516 517 518 519 520 521 522 ME failure SMS service of ME reserved Operation not allowed Operation not supported Invalid PDU mode parameter Invalid text mode parameter SIM not inserted SIM PIN required PH SIM PIN required SIM failure SIM busy SIM wrong SIM PUK required SIM PIN2 required SIM PUK2 required Memory failure Invalid memory index Memory full SMSC address unknown no network service Network timeout NO CNMA ACK EXPECTED Unknown error or SMS collision User abort unable to store invalid status invalid character in address string invalid length invalid character in pdu invalid parameter invalid length or character invalid character in text timer expired Operation temporary not allowed
5. TCP IP information please refer to GSM related documents 2003 Systems amp Technology Corp All rights reserved P x M I IntelliTrac IntelliTrac X Series Protocol Document by S amp T 4 Functions of TA version 4 1 Set Unit Parameters Commands Tow This command is used to use the GPS speed as the criteria to detect the unauthorized movement of vehicle ST TRACKING This command is used to set Tracking command parameters ST MILEAGECLR This command is used to reset the mileage to 0 in the mileage report ST MILEAGESET This command is to set the Mileage and Max Speed status for the mileage report Description Execute this function to enable the unauthorized movement detection If the GPS speed is great than 10 Km hr over 30 seconds the unit will send a alert message to the control center with Report ID 9 Enable Connect the Input 2 of IntelliTrac X8 to ACC of vehicle Disable Connect the Input 2 of IntelliTrac X8 to permanent power source 12 or 24 V or connect to the power source of IntelliTrac X8 mE 3H 2003 Systems amp Technology Corp All rights reserved 224 M r il I IntelliTrac IntelliTrac X Series Protocol Document by S amp T ST TRACKING Track position from the unit For control center Description Execute this command to ask the unit to report back current GPS positional information to the control center according to the Mode par
6. TT TIT TTE 1 Scope OF the CO CUMICIE MEC 1 3 1 Related documents rere ete eee reed eee nde reete ne red ue rente een 1 32 ST Command Syntax ie tede tt tede eei e rhe cR OI D saa oc Dx Edda aere de 1 3 3 Entering successive ST commands on separate lines 2 4 Functions of TA yerstoltosodivddsnvesuixra tekst uq eap inn aiaenipedtidebuh skuos speson AER DP DU VIN E EHE 4 4 1 Set Unit Parameters Commands su 4 5 ADH RER 9 5 1 Report ID Descriptio icti cerei trt ene a tte tetes 9 52 STD Errors Descriptio etur inerte sa Rte d Net ete a ques a eda Ra lee nsa deque 9 5 37 CME Errors Description 10 54 CMS Errors DescrptiOn nin incau sanitised ieee Gi neti c YER ERE eee ce PE EUR aah 11 5 5 LED Indicators Function seen 13 5 6 About Systems amp Technology Corporation 14 2003 Systems amp Technology Corp All rights reserved A x g I Intellil rac IntelliTrac X Series Protocol Document by S amp T 1 Introduction To IntelliTrac X Series Protocol TA version This document describes the protocol of the IntelliTrac X Series devices The S amp T proprietary messaging protocol is used for all communications between the base and the device This protocol incorporates error checking message sequencing with full acknowledgement of received messages on request The base station sends messages
7. in SMS mode is 300 meters and CSD GPRS mode is 100 meters Times Frequency The range is from 0 to 65535 If Times 0 it means forever tracking Persist Tracking 0 The unit stops reporting position back to the server continuously if there is no GPS 1 The unit reports position back to the server continuously if there is no GPS reception with the last position E M AA TY 2003 Systems amp Technology Corp All rights reserved 5 A x g I Intellil rac IntelliTrac X Series Protocol Document by S amp T Return Value OK TRACKING UnitID DateTime Longitude Latitude Speed Heading Altitude Satellites ReportlD InputStates OutputStates Mileage Max Speed SMS SendingTime Note Mileage the total mileage has traveled MaxSpeed the maximum speed during the trip SMSSendingTime the sending time according to the Time Zone setting when the message sends out from the unit Example ST TRACKING 0000 1 15 0 5 0 OK TRACKING 1010000002 20040929101800 121 645337 25 063437 0 0 0 4 2 0 0 0 3 6 48 20040929101800 1010000002 20040929101815 121 645337 25 063437 0 0 0 4 2 0 0 0 3 6 48 20040929101815 1010000002 20040929101830 121 645337 25 063437 0 0 0 4 2 0 0 0 3 6 48 20040929101830 1010000002 20040929101835 121 645337 25 063437 0 0 0 4 2 0 0 0 3 6 48 20040929101835 1010000002 20040929101840 121 645337 25 063437 0 0 0 4 2 0 0 0 3 6 48 20040929101840 1010000
8. to the device and waits for an acknowledgement message from the device to indicates the status of the request So this guide covers all protocol information you need to design and set up AVL applications incorporating the IntelliTrac X Series devices Note This document is for the special functions in addition to the standard version of firmware 2 Version History Version What s new Firmware version Hardware version required required 2 1 TA Add Tow function V1 319TA or above ST_2002_ or above Add MILEAGECLR command Add MILEAGESET command Modified ST TRACKING command V1 332TA or above 3 Scope of the document This document presents the ST Command Set for the IntelliTrac X Series devices 3 1 Related documents IntelliTrac X Series Hardware Installation Guide IntelliTrac Tracer Software User Manual IntelliTrac InstallWizard User Manual IntelliTrac ZoneManager User Manual 3 2 ST Command Syntax The ST or st prefix must be set at the beginning of each command line To terminate a command line enter lt CR gt Commands are usually followed by a response that includes lt response gt lt CR gt lt LF gt Throughout this document only the responses are presented lt CR gt lt LF gt are omitted intentionally Types of ST commands and responses Read command This command returns the currently set value of the parameter or parameters Test command ST XXXX lt gt lt CR gt lt LF gt Returns XXXX lt gt l
9. 002 20040929101845 121 645337 25 063437 0 0 0 4 2 0 0 0 3 6 48 20040929101845 2003 Systems amp Technology Corp All rights reserved 6 p v M I IntelliTrac IntelliTrac X Series Protocol Document by S amp T Description Execute this command to Syntax ST MILEAGECLR Password Reset Mileage ST MILEAGECLR 0000 Parameters Password The password of the unit The default password is 0000 Return Value OK MILEAGECLR Example ST MILEAGECLR 0000 OK MILEAGECLR mE s aaa aaa RM 2003 Systems amp Technology Corp All rights reserved qu I IntelliTrac IntelliTrac X Series Protocol Document by S amp A ST MILEAGESET Set the mileage report Description Syntax Parameters Return Value Example Execute this command to set the status of Mileage and Max Speed parameters for the mileage report Write Command ST MILEAGESET Password Mode Frequency Read Command ST MILEAGESET Password Password The password of the unit The default password is 0000 Mode Mileage KM Max speed Km hr 0 Invalid Invalid 1 Valid Invalid 2 Invalid Valid 3 Valid Valid Note 1 If any above parameter is set to Invalid the value in the mileage report would be incorrect 2 The Maxspeed will return to 0 automatically when the mileage report is sent Frequency The unit will send the mileage report to the base station according the frequency days
10. ameter Syntax ST TRACKING Password Mode Time Distance Times Persist Tracking Parameters for Password The password of the unit The default password is 0000 Tracking command Mode 1 Time mode A positional record is sent to the application when the time elapsed since the last position sent is greater than or equal to the time specified in parameter Time 2 Distance mode A positional record is sent to the application when the distance between the current GPS position and the last position sent is greater than or equal to the distance specified in parameter Distance 3 IntelliTrac mode A positional record is sent to the application as determined by proprietary algorithms These algorithms attempt to minimize the amount of data sent back to the application while maintaining a high degree of map replay accuracy 5 Time mode ACC checking If ACC is off the tracking function will be stopped 6 Distance mode ACC checking If ACC is off the tracking function will be stopped 7 IntelliTrac mode ACC checking Time Specify elapsed time The time specified is in seconds and can be any number from 0 to 65535 seconds Only whole numbers can be used The minimum time interval in SMS mode is 15 seconds and CSD GPRS mode is 5 seconds Distance Specify elapsed distance The distance specified is in meters and can be any number from 0 to 65535 meters Only whole numbers can be used The minimum distance interval
11. kage error O O1 BB ND EEE ZE 2003 Systems amp Technology Corp All rights reserved 9 I IntelliTrac IntelliTrac X Series Protocol Document by S amp A 5 3 CME Errors Description Error Code Description 3 Operation not allowed 4 Operation not supported 5 PH SIM PIN required 6 PH FSIM PIN required 7 PH FSIM PUK required 10 SIM not inserted 11 SIM PIN required 12 SIM PUK required 13 SIM failure 14 SIM busy 15 SIM wrong 16 Incorrect password 17 SIM PIN2 required 18 SIM PUK2 required 26 Dial string too long 27 Invalid characters in dial string 30 No network service 31 Network timeout 32 Network not allowed emergency calls only 40 Network personalization PIN required 41 Network personalization PUK required 42 Network subset personalization PIN required 43 Network subset personalization PUK required 44 Service provider personalization PIN required 45 Service provider personalization PUK required 46 Corporate personalization PIN required 47 Corporate personalization PUK required 48 PH SIM PUK required 100 Unknown 103 Illegal MS 106 Illegal ME 107 GPRS services not allowed 111 PLMN not allowed 112 Location area not allowed 113 Roaming not allowed in this location area 132 Service option not supported 133 Requested service option not subscribed 134 Service option temporarily out of order 148 Unspecified GPRS error 149 PDP authenticati
12. on failure 150 Invalid mobile class 256 Operation temporary not allowed 257 Call barred 258 Phone is busy 259 User abort 260 Invalid dial string 262 SIM blocked 2003 Systems amp Technology Corp All rights reserved 10 I IntelliTrac IntelliTrac X Series Protocol Document by S amp T 5 4 CMS Errors Description Error Code Description 1 Unassigned unallocated number 8 Operator determined barring 10 Call barred 21 Short message transfer rejected 27 Destination out of service 28 Unidentified subscriber 29 Facility rejected 30 Unknown subscriber 38 Network out of order 41 Temporary failure 42 Congestion 47 Resources unavailable unspecified 50 Requested facility not subscribed 69 Requested facility not implemented 81 Invalid short message transfer reference value 95 Invalid message unspecified 96 Invalid mandatory information 97 Message type non existent or not implemented 98 Message not compatible with short message protocol state 99 Information element non existent or not implemented 111 Protocol error unspecified 127 Interworking unspecified 128 Telematic interworking not supported 129 Short message Type 0 not supported 130 Cannot replace short message 143 Unspecified TP PID error 144 Data coding scheme alphabet not supported 145 Message class not supported 159 Unspecified TP DCS error 160 Command cannot be actioned 161 Command unsupported 175 Unspecified TP
13. s Contact Information for System amp Technology Corp ur S amp T Web Site http www systech com tw Technical Support Hotline 886 2 26981599 Technical Support E mail AVL ms systech com tw Main Phone 886 2 2698 1599 Main Fax 886 2 26981211 2003 Systems amp Technology Corp All rights reserved 4
14. t gt lt gt lt CR gt lt LF gt 2003 Systems amp Technology Corp All rights reserved A i g I Intellil rac IntelliTrac X Series Protocol Document by S amp T Write command This command sets user definable parameter values Test command ST XXX lt gt lt CR gt lt LF gt Returns OK XXXX CR LF Default parameters are underlined throughout this document 3 3 Entering successive ST commands on separate lines When you enter a series of ST commands on separate lines leave a pause between the preceding and the following command until the final response for example OK XXXX appears This avoids sending too many ST commands at a time without waiting for a response for each EEE 2003 Systems amp Technology Corp All rights reserved 22 g I Tz ntelliT rac IntelliTrac X Series Protocol Document by S amp T Communications The IntelliTrac X Series protocol could be transmitted to the IntelliTrac unit by several communication methods Such as Direct connection Baud Rate 57600bps GSM CS Data connection Baud Rate 9600bps GSM SMS messages Peer to peer and TCP IP network GPRS TCP IP UDP IP connection GSM SMS Peer to Peer GSM CS Data Connection Direct Connection BA GSM SMS TCP IP For more detail GSM CS Data SMS
Download Pdf Manuals
Related Search