Taurus 3 Ring Saw Manual
Contents
1. each blade in each material you can feel it while you are cutting Sensitivity to this causes extremely long blade life Defined it is that point at which you get maximum cutting speed for minimal pressure The Magnificent Seven Serious Blades Note When describing blade abilities it is wise not to confuse the ability of a blade to cut a certain material greater thickness once in awhile as opposed to that same blade being used to cut only that thickness all the time For this description we will refer to blade capacity vs normal use When we speak of blade shape it is what is called a cross section which is like snipping off a piece of the blade and looking directly at its end Standard Blade part 1042 Stained glass pattern and all around multi purpose cutting blade Its action is omni directional This is to say that it cuts the same speed and kerf swath left by the blade in any direction This blade was the first blade to be put on saws and makes pattern cutting very easy because the user does not have to turn the piece while cutting but simply move it in any direction Blade Shape Round 072 Diameter note 1 16 equals 063 and Imm equals 0394 Grit is aggressive Material Thickness Capacity 3 8 normal use is 1 8 art glass 1 4 soft wall tile What to Avoid Do not use for ceramic tile 3 8 fused glass pieces or thick material in general Average Blade Life 40 60 hours Separating Blade part 1043 This blade is the same a2. both the underside of the saw where the blade exits for water reduction and on the work surface for inhibiting debris from entering moving parts Before applying the hole reducer clean the areas around the blade thoroughly and dry completely To apply peel a hole reducer off of the sheet Open the slit and wrap the hole reducer around the blade Note when applying 2 the hole reducer to the 2 underside of the saw it vs is best to make it x overlap Page 20 The Magnificent 7 Blades of the Taurus 3 What Are They All About There are 7 blades available for the Taurus 3 ring saws and there are often questions arising as to what they are for how long they last and how to use them So we are writing this article to ive a summary of all of them and their many uses There are now seven blades to choose from There are universal truths about all of the blades that hold true for all of them 1 All blades cut the same materials glass tile stone shell nonferrous metals hard plastics such as acrylic and lexan and anything that has a similar density to these materials 2 All blades use the same belt and grommets Blades are interchangeable with the same belt and grommets and do not need to be changed unless they are excessively worn 3 Always let the blade do the cutting Forcing the blade through the material in a hurry will not only cause a slower cut but can also shorten the blade life There 1s an optimum speed for
3. functional and artistic photos are welcome We have an annual newspaper called The Bull Sheet which often portrays our favorite pictures for the year We also have a contest for the best picture which wins a free blade and gets your picture in the paper Thank you We appreciate your business Respectfully yours Jesse G Cogswell President Gemini Saw Co Inc 3300 Kashiwa St Torrance Ca 90505 Phone 310 891 0288 Fax 310 891 0265 www GeminiSaw com Lay box down with logo facing up Pull the saw out by the tub the unit will come out as one piece SC ne Remove top piece Page 1 UNPACKING YOUR MACHINE WORK SURFACE Lift off work surface resting on top of the foam This view shows your saw with all the parts it comes with UNPACKING YOUR MACHINE Cont This is the foot that also is used with the saw when it s used out of the tub covered on page 12 page 5 Remove saw body from bottom Remove bottom piece foam piece Page2 INSTALLING MACHINE BOTTOM MOUNT EX Remove lower door and thumb Be sure that the saw sits flush with screw and slide the saw into the the bottom mount groove of the water tub Push down and back on the saw Clip engaged until clip engages the water tub Note To remove the saw from the water tub disengage clip by pulling away from the tub then follow the previous steps in reverse order Page 3 INSTALLING WORKSUR
4. grommets are different Please note the chart below for reference numbers The description and action of these blades is the same for all saws Standard Blade Part 1039 Separating Blade Part 1041 Slim Blade Partt 1040 Dichro Blade Part 1038 TAURUS 3 EXTRAS Slicer Blade amp Belt Kit Part 1051 Speed Blade and Belt Kit Part 1052 Flocked Belt Part 0108 Made especially for slicer blade and speed blade this belt is probably overkill for all other blades and it costs a little more It has a Kevlar flocking or criss crossed webbing that holds the rubber together so that it can t easily split ALL NEW TITAN TABLE SAW Note We have a new saw called the Titan It was developed for those persons who could use a small table saw along with the ability to cut curves This saw will cut up to 12 long with very straight cuts It is great for glass tile fused glass slicing bottles porcelain objects or bowls It utilizes a mega blade which leaves a great edge and is sturdy enough to that it can cut intricate curves also It is a great advantage to have this saw as it takes up little space 2 x18 and gives you an extra ring saw if your partner is using the other one This saw gives the user the ability to use a full 3 of blade exposure for the working of hot glass projects Mega Blade Titan Partt 1048 Note Always be sure to order genuine Gemini Saw parts as this assures your warranty and that you will get maximum life out of
5. out of saw Saw TIP The following steps will make starting the process of replacing the blade much easier Wrap the drive belt tightly around While still pinching Slip the drive the blade and pinch with your belt and blade into position thumb and forefinger Page 9 Slip drive belt and blade past blue The GOLDEN RULE when replacing pulley 5 then wrap the drive belt any parts in the saw is to rotate the around it From this point just drive gear counter clockwise by hand follow the previous steps in reverse several times to make sure everything order is rotating smoothly USING THE SEPERATING BLADE COUPLING a Find the coupling Open the coupling and slide the material with pre drilled hole through the gap NOTE When a separating blade is installed the female side should always face up Put the blade back together and slip the belt back on the drive pulley 8 Page 10 MEGA BLADE Because of the MEGA blades more sturdy construction you may find it more difficult to install The following will help making the installation much easier Remove blue pulley 5 UN Slide belt and blade into machine using the same method described on page 10 Pagell MEGA BLADE Cont Wrap drive belt 9 around blue Wrap drive belt 9 around blue pulley 1 and slip them into pulley 5 and slip them into position Insert screw and tighten position Insert screw and tighten Slide groove gromm
6. the parts you purchase Thank you for choosing Gemini Saw Company Inc and allowing us the pleasure of helping to unleash your imaginations Sincerely Jesse Cogswell President
7. there is another alternative Add 2 to 3 table spoons of vinegar to your tap water further steps can be taken as well like adding just a few drops of ordinary dishwashing liquid When the saw is being used for an extended period it is always a good idea to add an ice pack to the water or change it to keep it cool With this saw it is better to use the ice packs rather than ice cubes as the cubes will float freely throughout the saw and may get jammed in the inner workings It is not recommended to use any type of antifreeze or coolants Care Always keep the water in your saw cool and clean as possible It is all right to leave the water in the saw for a few hours of even a day but it is never a good idea to leave the water sitting idol in the saw for long periods The contents in the water minerals and debris from cutting will tend to settle in and around the moving parts and cause rapid wear Page 7 Loosen Groove Grommet 7 and Lift up on tension arm 10 and slide slide it back When replacing the drive belt off of blue pulley 4 blade slide it forward until it makes contact with Groove Grommet 6 M Gently unwrap drive belt from blue Unwrap drive belt from blue pulley pulley 5 3 1 Pa 1 p F i Tan d T E s 4 a pP kh rap belt from blue pulley Gently unw 1 Unwrap belt from blue pulley 2 l Page 8 BLADE IN OUT Cont Gently pull drive belt 9 off of the Lift blade
8. tile 1 4 fused glass pieces or thick material in general Average Blade Life 40 60 hours Speed Blade part Sometimes known as the inverted Mega blade we turned a mega inside out and made it thinner The result is a tear dropped shaped blade that is almost unbreakable with the round part on the inside and the point on the outside Its thinner profile makes it our fastest most aggressive blade yet When pushing forward into this blade it glides through the thickest toughest materials with ease It comes with a Flocked belt only as this is the only belt that can handle its aggressive nature Its action is omni directional in stained glass or soft wall tile and forward and backward for thicker or harder materials When pushing or pulling the material through with this blade it has a thinner kerf than a Standard Mega or Slim blade 055 Blade Shape Tear Drop 055 inside x 150 front to back Grit is aggressive Material Thickness Capacity 3 4 normal use is fused glass stained glass ceramic tile and stone Note you will have to remove the stabilizer foot to use the full 5 4 capacity What to Avoid Do not cut thin dichroic glass as it will chip easily Demonstrate to students its action prior to letting them use it explaining the tear drop shape and its uniqueness Average Blade Life 50 100 hours TAURUS I II AND II 2 These saws can use 4 of the previously mentioned blades They have different part numbers because the
9. FAGE Slide work surface onto water tub 2 6 0 9 9 9 6595 93 6 6 TT 6 K A A A AU A e cas gt og anf Lu ow ea M 4 LANG E nS S7 o o a tu NY E e c gt wn 5 FP o that hold the saw in position MILL Hitt am ML LITITIT Push down on work surface to make sure that it is seated on the water tub Page 4 INSTALLING FACESHIELD Insert the tabs on the face shield into the indentions on the upper door and the body Page 5 9 ov v ow V 999 9 999 9 Face shield should look like this It will flip up out of the way when not needed Note the shield needs to come off to remove door REMOVEIINSTALL UPPER DOOR The rear side of the upper door has Pull the tab toward you to pop the a finger tab upper door off To put the door on snap the front Snap the back portion of the upper part of the upper door on and hold door into position it in position Page 6 WATER Level Conditions and Care Fill the water up to the watermark The water should come half way up located on the front of the water tub the bottom blue pulley 4 Conditions Water conditions vary from region to region Areas with hard water will have an adverse affect on the saws moving parts especially the bearings The best environment for the saw is distilled water Distilled water is not always the most cost effective way to go but
10. GEMINI SAW COMPANY TAGRUS2 RING SAW Gemini Saw Company Inc 3300 Kashiwa Street Torrance CA 90505 Phone 310 891 0288 Serial Date of Purchase Fax 310 891 0265 I www geminisaw com WWW GEMINISAW COM Rev 1 10 TORRANCE CA 90505 TEL 310 891 0288 FAX 310 891 0265 Parts List 1 Blue Pulley Assembly 1067 6 Orange Grove Grommet Assembly 1070 2 Blue Pulley Assembly 1067 7 Orange Grove Grommet Assembly 1070 3 Blue Pulley Assembly 1067 8 Drive Pulley 0035 4 Blue Pulley Assembly 1036 9 Drive Belt 0070 5 Blue Pulley Assembly 1067 10 Tension Arm 1031 13 Foot Assembly Stabilizer 1034 Note Orange Groove Grommets should always face in opposite directions as shown on diagram above TABLE OF CONTENTS To All Ring Saw Customers Forward Unpacking Your Machine page 1 2 Installing Machine page 3 Installing Work surface page 4 Installing Faceshield page 5 Install Remove Upper Door page 6 Water Level Conditions and Care page 7 Blade In Out page 8 10 Using The Separating Blade page 10 Mega Blade page 11 12 Using The Handheld Saw page 13 14 Helpful Hints page 15 Cutting Other Materials page 16 A Little About The Saw page 17 Stabilizer Foot page 18 19 Taurus Hole Reducers page 20 Parts List inside back cover WARRANTY INFORMATION To the original purchaser Gemini Saw Co Inc warrants the product and all of its component parts to be free of defects in material or workmanshi
11. e and its operation is very different than any other machine For this reason persons who have been using band saws tend to lead the material into the front of the saw blade and rotate the material to make a curved cut All cuts on the Taurus Ring Saw can be made by moving the material forward backward left and right so rotation is not necessary Diagonal directions are the strongest Ice can be used with the Taurus ice packs or blue ice is safer and also lasts much longer This 1s useful as cold water works wonders for blade life and cutting speed but 1s not necessary unless the saw is being used for periods of fifteen minutes or more Sporadic use for one minute or less for example will not build up enough heat to warrant ice Coolant is not necessary for the Taurus as it moves enough water through the cut to make it the coolest cutting saw on the market today Page 17 STABILIZER FOOT FOR TAURUS 3 Taurus 3 Ring Saw made even better The new Taurus 3 Ring Saw Blade Stabilizer reduces grommet wear dramatically It also gives you more control and stability when cutting thicker material The Stabilizer adjusts easily to accommodate different thickness material Perfect when using the standard blade separating blade mega or slicer blade The spectacular improvement will be included in all Taurus 3 Ring Saws starting this June at no additional cost The Stabilizer will fit all previously purchased Taurus 3 Ring Saws without any modificat
12. ers in rods and pattern bars and scroll cutting of fused glass up to 3 8 thickness Average Blade Life 50 100 hours Slim Blade part 1043 Originally developed for the Taurus I thru II 2 series as a thinner version of the standard blade It has the same dimension as a standard or separating blade front to back but is thinner as you look at it straight on For this reason it 1 just as strong as a Standard Blade but can cut quicker front to back and leave a slightly smaller kerf 062 It cuts the same as a standard blade left o right and its action is omni directional Blade Shape Oval 062 x 072 front to back Grit is aggressive Material Thickness Capacity 5 8 normal use is 1 5 art glass 1 4 wall tile What to Avoid Do not use for ceramic tile 3 8 fused glass pieces or thick material in general Average Blade Life 40 60 hours Dichroic Blade part 1049 NEW This is the slim blade but coated it in super fine grit so that it does not chip even the thinnest of dichroic glass Its cut is super quick and leaves the smoothest edge of all of the blades allows the use of lower firing temperatures in the manufacture of jewelry and the like Neat crisp edges add a note of professionalism with this blade Its action is omni directional Blade Shape Oval 058 x 072 front to back Grit is finest Material Thickness Capacity 1 4 normal use is thinner than normal dichroic or iridized glass What to Avoid Do not use for ceramic
13. et 7 until it makes contact with the blade It will not touch groove grommet 6 Page 12 HANDHELD SAW The inside has a die cut sponge inside to hold water inside Soak it prior to assembly This is the bottom cover that is used on the handheld unit The bottom cover comes with a Snap the back of the cover in place thumbscrew that will hold it on and keep the water from leaking out prematurely Screw the thumbscrew down snug Page 13 HANDHELD SAW Slide the foot onto the tab on the underside of the nose of the saw Slide the foot down until the space between it and the base of the saw is slightly larger than the thickness of the material being cut Rest the foot on the material when cutting Do not hold it above the material Note When cutting the sponge will give 5 10min of use then the cut will start to show powder Do Not Keep Cutting Add water by squirt bottle through the hole the blade goes through or re soak the sponge Clean the sponge often especially after use Page 14 The foot comes with a phillips head screw and nut Put them on loosely Snug the screw down to secure it in place HELPFUL HINTS To apply patterns onto your work piece a copying machine is helpful The print can be sprayed with Scotchguard fabric protector covered with a film of rubber cement or simply copied onto Mylar which makes the print waterproof The print can then be affixed t
14. ions and will be available at your favorite supplier at a nominal cost Gemini Saw Company continues to add value to the Taurus 3 Ring Saw with yet Q When do I use the Stabilizer Foot A Always use it with the hand held unit When ever more control is desired in the shaping of thicker materials or for production cutting Q Does the Stabilizer Foot adjust A Yes it slides up and down to accommodate different thickness materials Q Does the Stabilizer Foot interfere with the light on the Taurus 3 A No it does not interfere You will still be able to see very well Q Can the Stabilizer Foot be used on other Taurus models A It can only be used on with the Taurus 3 Q Does the Stabilizer Foot come in different colors A It only comes in gray Q Is the Stabilizer Foot available for people who already own a Taurus 3 A Yes it is available and will require no modification Q Where is the Stabilizer Foot available A You can purchase it at your local supplier or distributor Page 18 STABILIZER FOOT INSTALLATION Rotate the Stabilizer foot up into blade and roll it down at an angle the mount on the saw into position Insert screw through Stabilizer Foot position as needed and tighten screw down Peel the red grommet off of the Snap new grommet and reinstall bearing in reverse order Page 19 T Taurus slale Ran Wooly The new Taurus hole reducers come on a Sheet and are useful on
15. it is aggressive Material Thickness Capacity 3 4 normal use is fused glass stained glass ceramic tile or stone You may have to remove the stabilizer foot to use the full 3 4 capacity What to Avoid Do not cut thin dichroic glass as it will chip easily demonstrate to students its action prior to letting them use it explaining the tear drop shape and its unique action Average Blade Life 50 100 hours Slicer Blade part 1046 This is our thinnest blade and only cuts forward and backward It can grind slightly left and right but take your time and it will turn on a dime or smaller Its action is just like that of a band saw but infinitely better in that you rotate the material into the blade as you are cutting but you can in the middle of the cut without binding and head off in any direction either backwards or forwards This blade was developed for slicing material quickly with a thin kerf 040 1mm and it is the blade we recommend for use with the Super Slicer a jig for slicing pattern bars and rods into thin repeatable wafers Also it has finer diamond so the cut is even smoother than all the other blades except for the dichro blade Use this blade with the heavy duty flocked belt to avoid splitting This blade can turn on a dime and do very intricate designs once you get used to it Glass fusers love it Blade Shape Flat 040 width x 150 length Grit is fine Material Thickness Capacity 5 4 normal use is for slicing thin waf
16. nd off a bump go right to the bump and grind it right in the middle and slowly move side to side Pg 15 CUTTING OTHER MATERIALS The Taurus will cut all kinds of materials These materials will not load the blade they include but are not limited to tile gold which can be refined out of the water bath silver brass bronze aluminum stainless steel copper and plastics such as lucite plexiglass composites and all types of stone The Taurus can be used as a high speed coping saw and will greatly reduce you metal cutting time Slight loading can occur with aluminum over a period of time Periodic cutting on a piece of brick will remove it from the blade When cutting thin metals it is best to put a backing under the metal so that the burrs created by the saw action will not catch on the work surface This material can be the kind of cardboard found on the back of a writing pad Another backing that works well is foam core white which can be found at artists supply stores everywhere The blade of the Taurus will not be effected by any material you choose as a backing because it cuts plastics as well as metals and will not load on these either When removing the blade from a cut where you are not separating two pieces so that you must find your way out of a maze it is sometimes a good idea to leave the saw running as this will help it slip through easier Pg 16 ALITTLE ABOUT TRE SAW The ring saw is a completely unique machin
17. o the material with the use of rubber cement Although cutting stacked glass can be accomplished better with the Gemini Saw than any other saw we want to discourage people from thinking this is faster Blade life is severely hampered by this process and it should not be done unless it 1s imper ative that all the pieces be exactly the same shape Cutting is actually faster one at a time Straight lines can be cut by placing a straight edge across the work table and clamping it at the ends The Ring Saw will give you a straight line at any angle Diagonal is best When cutting intricate shapes it is best to begin the cut with the most intricate part and end the cut on the thickest part This will greatly reduce the chances of the piece breaking When doing lots of tiny little pieces that would be difficult to pick up and keep track of it is sometimes best to leave them attached to the main piece by a small section that you can break off and grind later When guiding the saw around a fine point it 1s usually better to cut past the end of the point on the side and then come back as though you wanted a longer point than you actually need This will help develop your skill When you are first starting to cut out shapes do not try to cut right on the line as this will come with a little practice At first stay away from the exact line by a hair and come back afterwards and lightly grind it with the saw blade When you want to gri
18. p All of these components other than wear parts are under warranty for a period of three years from the date of purchase Wear parts blade bearings drive belt grommets spotlight face shield MISSION STATEMENT To provide machines to the industry which are efficient dependable long lasting attractive and innovative beyond the state of the art To listen to our customers and provide the best possible customer service and to treat all persons with whom we come in contact with dignity integrity and respect To all Taurus 3 owners We want to thank you for choosing Gemini Saw Co Inc makers of the most advanced shape cutting machinery today We believe that you will find the all new patented Taurus 3 Ring Saw the most important key to unlocking your imagination and speeding you on your way to creating new and wonderful shapes never before possible The Taurus 3 incorporates many new capabilities most of which have come from listening to you our customers We believe you will find these machines easy and fun to work with To further develop confidence in your new machine we would like to suggest that you familiarize yourself with the manual Please take the time to read about the machines basic operations and functions Please feel free to call us if you have any questions or grey areas concerning your new saw and its operation And also if you have time to send us a picture of what you have done with the saw both
19. s above but t comes apart or cutting out the center of something without using an entrance cut You must first drill a hole Consult your DVD for hole drilling instructions Blade Shape Round 072 Diameter note 1 16 equals 063 and 1mm equals 0394 Grit is aggressive Material Thickness Capacity 3 8 normal use is 1 8 art glass 1 4 soft wall tile What to Avoid Do not use for ceramic tile 3 8 fused glass pieces or thick material in general Average Blade Life 40 60 hours Mega Blade part 1045 This heavy duty blade is hungry for whatever you can feed it It is almost unbreakable so it is great for class settings It has an opinion about which way it likes to cut because of its shape which is basically tear dropped The round part of the tear drop faces outward and the pointed part faces inward This means it cuts faster when pulling towards yourself and slower pushing away and slowest sideways Its kerf is the same as a standard blade when pushing and pulling but it leaves a wide swath the same as a standard blade when pushing and pulling but it leaves a wide swath sideways That said you can cut whatever you can fit into the mouth of the saw and the shape allows for creative shaping Cutting action is Omni directional in thin material like stained glass but more forward and backward cutting for thicker harder materials Leaves a smooth edge Blade Shape Tear Drop 072 Diameter front x 150 front to back inside is pointed Gr
Download Pdf Manuals
Related Search