Home

operations from touch keypad

1. 0 j as The SMS sent in reply will show only the status of the Partitions assigned to the PIN used to make the request pg The SMS sent in reply may be delayed if there are other calls in the queue or may be lost if the queue is full or there are problems with the GSM network Arming Disarming the Partitions You can Arm and Disarm the Control Panel Partitions by sending the following SMS to the GSM number of the Control Panel ABS lt A AF gt lt PIN gt lt OFF OF ON A B C D gt lt Text gt gt A AF arms the Partitions without forcing the Blocking Conditions AF arms the Partitions forcing any Blocking Conditions see APPENDIX gt Arming Blocking Conditions PIN aUser PIN enabled to manage the control panel via SMS gt OFFI OF ON A BICID OFF or OF disarms the Parti tions ON arms the Partitions A B C or D disarms the Partitions in A B C or D Mode Text an additional text that can be used to assign a description to the command message and is ignored by the control panel ONLY the Partitions of the PIN used will be Armed Disarmed ps Control Panel will only accept SMS for arming dis arming the Partitions ONLY from the numbers present in the phonebook ask the installer or refer to KEYPAD OPERATIONS gt Program gt Telephone Numbers 2 6 If the operation is successful the Control Pan
2. RV 2 A N Q 5 2 p F Press OFF to insert the pound Press C to cancel an entry error Press ESC to cancel all characters v v v v us DO NOT insert pauses in numbers dialled via GSM 5 Press ENTER to confirm the Phone number and go back to step 3 ABSOLUTA OPERATIONS FROM LCD KEYPAD 45 m Change Pin 2 7 This option will allow you to change your PIN os Atdefault ONLY the User PIN 1 is Enabled and it is 0001 1 Press B to view the Change my PIN option 2 Press ENTER to select the option 3 Enterthe new PIN 4 to 6 digits required then press ENTER 4 Because the digits are masked by stars enter again the PIN to avoid errors then press ENTER If the two PINs match the keypad save the new PIN and go back to the User Menu else it keep the old PIN and go back to step 3 B Enable Disable Key 2 9 This option will allow you to Enable Disable the Keys use A Key be Enabled Disabled ONLY by PINs which operate the Partitions it is assigned to 1 Press B to view the Dis Ena key option 2 Press ENTER to select the option 3 Select the Key type to Disable enable Press 1 for Wireless Keys gt Press 2 for Proximity BPI Keys 4 Enter the Identification Number of the Key to Dis able Enable then press OFF to disable the Key
3. the will display iz i in signal display mode The system will end the call automatically if no valid PIN is entered within 30 seconds at default This inter val can be customized from 1 to 254 seconds ABSOLUTA TELEPHONE OPERATIONS 55 Entering Commands Once your PIN has been recognized you can enter the Command Codes ps The system will end the call automatically if no Key is pressed within 2 minutes m Cancel Command J Press to cancel the Command and step back to the Enter data phase Press to delete incorrect digits the system will emit an audible feed back signal 2 beeps to confirm that the data has been deleted On Hook If you accessing your system via Answering de vice mode press J to end the call B Remote Talk Listen in J ms This command requires the AS100 Audio station gt Press 1 to start the Remote Listen in session via the Audio Station microphone gt Press _U again to start the One way Talk session via the Audio station speaker required press U to switch from One way Talk to Listen in mode and vice versa The One way Talk and Listen in modes cannot be active at the same time gt Press 2 to start the Two way Talk Listen in ses sion via the Audio Station microphone and speaker This feature will allow you to listen in on the protected premises and talk to whoever is present Two way Ta
4. 3 Enterthe new Date and Time then press ENTER to confirm or ESC to quit and step back to the User Menu The Date and Time option will NOT allow you to change the digits individually therefore you must enter the entire Date and Time you press ENTER before completion the setting will be deleted Date Time format depends on the choice of language gt Italian dd mm yyyy hh mm gt English mm gg yyyy hh mm Others yyyy mm dd hh mm B PIN Programming 2 5 This option will allow you to set enable disable the User PINs At default ONLY the User PIN 1 is Enabled and it is 0001 The User PIN Programming can follow two procedures depending on the User PIN type ask to your installer Manual or Automatic default 1 Press A B to view the User PIN progr option 2 Press ENTER to select the option 3 Press Aor B to scroll the list of PINs the display shows the User PIN status Free Enabled or Disabled 4 Ifyou select set not Free User PIN you can press OFF to disable the User PIN gt ON to enable the User PIN gt ENTER to set the PIN and go to the step 6a or 6b 5 Ifyou select a Free you can press ENTER and go to step 6a or 6b Manual PIN You can choose your own preferred PIN 6a Enter the required PIN 4 to 6 digits required than press ENTER the sign will mask the entered digits Enter again the PIN
5. ABSOLUTA 3 50 OW EN50131 Expandable Hybrid Control Panel ABSOWLUTR www bentelsecurity com https itunes apple com https play google com store User Manual Default User PIN 0001 BENTEL SE Y A Tyco International Company Installation of the system must carrted out strictly accordance with the Instructions described in this manual and in compliance with the local laws and bylaws in force The ABSOLUTA Control panels have been designed and manufactured to the highest standards of quality and performance The ABSOLUTA Control panels have no user changeable components therefore they should be serviced by authorized personnel only BENTEL SECURITY does not assume responsibility for damage arising from improper application or use The manufacturer recommends that the installed system should be completely tested at least once a month Hereby BENTEL SECURITY declares that ABSOLUTA Control panels comply with the essential requirements and other relevant provisions of Directives 1999 5 EEC The R amp TTE Directive 2006 95 EC The low Voltage Directive 2004 108 EC The Electromagnetic Compatibility Directive This panel complies with EN50131 1 2008 EN50131 3 2009 and EN50131 6 2008 Security Grading 2 Environmental Class II MAINTENANCE Please verify the correct operation of security system at least once a month Periodically perform the steps below R
6. Remote Command events are the same as those that can be controlled via SMS read SMS OPERATIONS Events Controlled by SMS and through an i Phone or an Android smartphone with the ABSOLUTA App Based on Control Panel programming and installation Reserved Outputs and Remote Command events can be used to apply domotic features turning irrigation lights heating etc on off Ask your installer for more information Press Outputs to activate deactivate Reserved Out puts or Actions to switch the Remote Command events Outputs The display s central part lists the Reserved Outputs and their status Menu Scenarios H 5 Actions Press or to scroll the list then press On to acti vate the output or Off to deactivate it Actions The display s central part lists the Actions Menu Scenarios Outputs Scenarios ps The status of Actions cannot be known a priori Press or to scroll the list then press On to acti vate the action or Off to deactivate it ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 25 Info 1 Press WA or to scroll the list then press to view Arming Modes Menu Menu Partition 0 Scenarios Disarmed Partition 02 Partition Scenarios Zone Status xis Hu Disarmed t Partition 03 Into Status History Dig armed Te Info Event Buffer 02 GSM IP GSM IP Exit E P t
7. zJ Alarms Reset 51 Disable Current User 2 SMS 5 Events Controlled by Caller ID Events Controlled by SMS Partition Status Arming Disarming the Partitions Credit Check Disabling a PIN GSM Module IMEI Request APPENDIX PIN list ABSOLUTA App Arming block conditions Read this guide thoroughly to learn how to use your system See the Glossary to learn about the words used in the instructions B Glossary Alarm Zone A limited area of the premises monitored by detectors e g Motion detectors Door Window con tacts BPI Device A peripheral device connected to the Con trol panel by a 4 pin conductor Beep An audible signal emitted by the Keypad each time a key is pressed or when requested operations have been completed Buzz An audible signal emitted by the Keypad to indi cate that a requested operation is impossible or has been denied for example automatic exit from the User Menu at a LED keypad Buzzer An audible signalling device inside Keypads and PROXI Readers Central Station A private Security Company your Control panel will send Alarm Trouble and Emergency messages to that is if remote monitoring is enabled Detector A device which signals alarm conditions e g Glassbreak Forced entry etc Dialler A device which sends voice message to pro grammed phone numbers Digital Communicator An integrated on line device that sends digital signals D
8. rj ae cst display centre shows the control panel version v3 50IP in the example above and the Serial Number ofthe Control Panel 80003FD3 in the example above ms The information displayed depends on the Control Panel you own 1 The Absoluta Server supports the ABSOLUTA control panel in access to the Internet services remote service event notification via e mail and the ABSOLUTA app connection of the ABSOLUTA app to the Control Panel Ask your installer for more information ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 29 Screen Calibration For the touchscreen to operate correctly it must be cali brated as follows ps This operation must be done the first time the touchscreen is used and each time it does not re spond to touch correctly 1 Hold down the Home key for at least 3 seconds but less than 10 seconds Keypad Address 2 Press Screen Calibration Firmly press and hold each target for at least 2 seconds to activate the next target 3 Follow instructions on the display before 10 sec onds have gone by or the keypad will go back to the previous step 4 Press Exit to Standby to quit the Advanced Menu ms The other Advanced Menu items Keypad Ad dress Firmware Update and Refresh Labels are blocked because they are reserved for the in Staller 30 Expandable Hybrid Control Panel ABSOLUTA OPERATIONS FROM LCD KEYPAD ABS
9. This option will allow you to delete the Zone and Parti tion Fault and Tamper memories and set all Alarm sig nalling devices to Standby If Alarm signal persists after a Clear Fault Tamp command the causes of persistent Alarms must be cleared immediately 1 Press A or B to view the Clear Fault Tamp option 2 Press ENTER to select the option 3 Select 1 to delete Faults and or 2 to delete Tam pers then press ENTER to confirm 4 Press ENTER to delete Faults and or Tampers memories and active 5 Press ESC to step back to the User menu use From Stand by status after entering the User PIN if display shows Faults and or Tamper you can press the OFF key the keypad directly will manage the previous procedure of Clear Fault Tamper Program B ON OFF Answering 2 1 This option will allow you to turn ON OFF the Answering device If the Answering device is ON the Control panel will answer incoming calls with a Voice message your installer has recorded the required Voice messages for your system 1 Press A or B to view the ON OFF Answering op tion 2 Press gt ON to Enable the Answering device OFF to Disable the Answering device ESCto step back to the User menu p Ifthe Answering device facility is enabled an will be shown on the display directly above the 3 42 Expandable Hybrid Control Panel ABSOLUTA m Enable Installer Tel
10. s Exit Press 09096 gt Partition Status view change Partition sta 2 Press the desired Arming Mode to change Partition tus status gt Zone Status to view zone status and to bypass in clude zones gt Event Buffer to view event records gt Installer to display the installer contact details gt Bentel Security to display the information about LEAL Bentel Security 7 Partition 01 armed Read the relevant section for more information B Partition Status Menu The keypad goes to Standby when the operation se lected is over Partition Scenarios Disarmed Partition Zone Status Disarmed Info History 4 Installer 5 Bentel Security Exit This option allows you to view and change Partition status The display s central part lists Partitions common to the Keypad and to the PIN used to login and the Partition status gt Disarmed if the Partition is disarmed gt Away if the Partition is armed in Away mode Stay if the Partition is armed in Stay mode No Delay if the Partition is armed in Stay mode without Entry and Exit Delay Al if the Partition is in alarm status gt AI M if the alarm status has occurred in the past memory gt if a zone of the partition is bypassed T if one Zone of the Partition is being tested f a zone is being tested contact your installer for more information 26 Expandable Hybrid Co
11. 1 2 3 4 5 6 T 8 9 Proximity Reader function LEDs refer to OPERATING YOUR SYSTEM FROM READER section Home Key Slot for SD memory card B Models This Manual is designed for anyone using a Control panel from the ABSOLUTA range Most of the features described in this Manual are included on all ABSOLUTA Control panels However some features are included on certain models only in such cases the name of the Con trol panel will be specified see Table 1 ABSOLUTA INTRODUCTION 5 Enter PIN enter l B Figure 1 ABSOLUTA supported A PREMIUM LCD B CLASSIKA LCD C ABSOLUTA M Touch ABSOLUTA 16 ABSOLUTA 42 ABSOLUTA 104 Max Number of Keypads 8 8 16 Number of user PINs 31 63 127 Number of keys 64 250 Number of Key readers 16 32 32 Number of input expansions 32 32 32 Number of output expansions 16 16 16 Number of power supply stations 0 4 4 number of wired zones 16 42 Max number of wireless zones 32 32 32 Total max number of combined 42 wired wireless zones Number of partitions Max number of output Max tele
12. 3 Press Bio scroll the list then touch the desired event to view details in the display s central part gt the first row displays Restore if an event has been restored gt the second row displays the Name of the event gt the third row displays the Date of the event gt the fourth row displays the Time of the event gt the fifth row displays Who caused the event gt the sixth row displays Where the event happened or Why it happened gt the seventh row displays Partitions involved in the event ps Information displayed depends on the event B Installer Menu info Partition Status Scenarios Company Name Status Installer 1 Into Address Line 1 History Address Line 2 GSM IP Address Line 3 Bentel Security p 1234 123456789 ET This option allows you to view the personal data of the installer if programmed ask your installer for more in formation B Bentel Security Menu info Partition Status Scenarios Zone Status History Bentel Security Tyco Security Products GSM IP Installer E mail Infobentelsecurityzbtyconnt corm www bentelsecurity com This option allows you to view some information about Bentel Security GSM IP 0040 lt Status Menu i SIM Number Scenarios IMEI Info 861785005583749 IP i EN Signal EI GSM IP Received
13. F SMS Mess F Yes None Yes Continued 2 The Squawk can be avoided 3 Arming without attribute F 4 Arming with attribute F ABSOLUTA APPENDIX 65 Via Gabbiano 22 Zona Ind S Scolastica 64013 Corropoli TE ITALY Tel 39 0861 839060 Fax 39 0861 839065 e mail infobentelsecurity tycoint com http www bentelsecurity com ABS DOCIINT UKIFR ABSOLUTA DOC MANUALS KIT PENK TEL 6 ABSDINT4 0 0 ISTISBLEKE 7 0 ISTUSBLEKE 7 0 ISTISBLFKE 6 0 ISTUSBLFKE 6 0 N ABSOLUTA INSTALLER MANUAL ABSOLUTA USER MANUAL MANUEL D INSTALLATION ABSOLUTA MANUEL DE L UTILISATEUR ABSOLUTA BENTEL MADE SECURIT Y IN ITALY ISTUSBLEKE 7 0 170414 V10
14. Type A B C or D Labels of Stay Arming Modes can vary based on installer programming ms Any arming mode labels that exceed the space available scroll automatically to display the excess part read Keypad gt Scrolling Test for more infor mation 2 Label of Arming Mode selected 10 Expandable Hybrid Control Panel ABSOLUTA 3 Description of Arming Mode selected use Arming Mode descriptions are programmed by the installer 4 Current Arming Status The coloured box shows current Partition status Disarmed gt GREEN with the label Disarmed if ALL Keypad Partitions are DISARMED RED with the label Armed Global if ALL Keypad Partitions are ARMED ge RED with the label Armed if AT LEAST ONE Keypad Partition is ARMED gt 5 Arming disarming key The grey key arms the Parti tions as selected or disarms them Arm Global gt GREY with the label Arm Global ARMS ALL the Partitions of the Keypad and PIN used Arm STAY typeA L4 GREY with the label Arm STAY type A ARMS DISARMS the Partitions of the Keypad and PIN used in the programmed mode us The label Arm STAY Type A Arming depends the Arming Mode selected and can be modified by the installer Disarm oom GREY with the label Disarm DISARMS ALL the Partitions of the Keypad and PIN used Here below you will find some possible combinations of the box displaying the current s
15. Disarming Partitions DESCRIPTION ON Control panel Tamper Control panel open or dislodged Blinking Control panel Tamper has cleared but at least one Open Panel event in memory ON System Tamper Blinking System Tamper has cleared but there is at least one System Tamper event in memory ON Tamper on at least one peripheral device Keypad Reader Expander or Receive Blinking Peripheral Tamper has cleared but there is at least one Peripheral Tamper event in memory ON A False Key Card is present at a Reader Blinking At least one False Key Card event in memory ON A peripheral device Keypad Reader Wireless or Expander has been disconnected Blinking At least one Peripheral Trouble event in memo Table 4 Tamper signals 1 DESCRIPTION o oO oOo yY O Y OFF Installer Disabled ON Installer Enabled Blinking PIN Transfer Enabled 22 MEE Answerphone facility Enabled a OFF Line Free ON Line Busy Blinking Line Down Table 5 Telephone signals ABSOLUTA OPERATIONS FROM LCD KEYPAD 09 B Fast Keys Superkeys Ifyour Installer has set up the 3 Superkeys 1 2 and 3 you will be able to operate your system from the key pad without using PINs The Superkeys can be pro grammed to activate gt the Digital Communicator to transmit event codes to the Central Station gt the Dialler to send a voice message requires AS100 Audio Station for customized voice
16. Partitions have been disarmed read the follow ing paragraph to cancel the transmission of events See Menu User Stop Alarms if the disarming of the Zones does NOT block the visual audio siren signal ling devices ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 13 B Clear the transmission of events 1 Enter the Home Screen as described in Entering the Home Screen 25 System in arm MS Thursday April 17 2014 z Global EIE type A type B 2 Press to cancel the transmissions progress and any more queuing Clear Call Queue 3 Press Yes to confirm Viewing Signals The LED A indicates signal alarm tampering fault or zone bypass If all signals have ended the LED A blinks to indicate that signals have occurred memory fthe Keypad has the EN50131 option enabled the led ONLY displays system status when ALL keypad Partitions are disarmed ask your installer for more information To view signals in progress and those memorised fol low instructions below 1 Enter the Home Screen as described in Entering the Home Screen 2 Press the icon in the top left on the display this icon can be as follows with decreasing priority gt e fixed in an alarm gt A fixed with tampering or fault gt blinking with an alarm memorised gt A blinking with tampering or a fault memorised gt v fixed with zones bypassed War
17. SMS Credit 5 5 Balance Provider APP vodafone IT Kw mama Ld a O t y y E Press gt GSM to view information on the GSM Module to check credit balance on the prepaid card inserted in the GSM Module to read SMSs received by the GSM Module gt IP to display the status and information related to the IP module gt APP to view information on configuring the ABSOLUTA App to manage the control panel by iPhone and Android smartphone Read the relevant section for more information m GSM The display s central part shows gt SIM Number phone number of the SIM inserted in the GSM Module gt IMEI the GSM Module IMEI gt Provider name of the GSM operator gt Signal GSM signal intensity B SMS Credit Balance 1 Press SMS Credit Balance to know how much credit is left in the card inserted in the GSM Module credit balance sent via SMS w Confirm X Cancel 2 Press Confirm to confirm the request or Cancel to cancel it the Control panel will send a request to the GSM operator to obtain the remaining credit When the Control Panel receives the remaining credit information message the icon m in the upper lefthand corner of the display appears and the Home key blinks read Received SMS for instructions on how to read SMS messages 28 Expandable Hybrid Control Panel ABSOLUTA B Received SMS 1 Press Received SMS to read massages received by the GSM Mo
18. field of Reader for more than 10 seconds or until all three LEDs start slow Blinking and no Arming Disarming operation shall be performed RED Light Indicator ON the system will Arm when you remove the Key from the Reader REDLight Indicator blinking arming blocking con ditions has been detected AMBER Light Indicator ON the system will arm in A Mode when you remove the Key from the Reader AMBER Light Indicator blinking A Mode arming blocking conditions has been detected GREENLight Indicator ON the system will arm in B Mode when you remove the Key from the Reader GREEN Light Indicator blinking B Mode arming blocking conditions has been detected B No Key at Reader When no Key is present at the Reader the Light Indica tors will signal as shown in the following table DESCRIPTION OFF OFF OFF The system is Disarmed ON OFF OFF Atleast one Reader s Partition is Armed ON ON OFF system is armed in A mode ON ON system is armed B mode Fast flash on RED LED indicates a running alarm Slow flash on RED LED indicates an alarm memo The Partitions that are not controlled by the Reader will not affect the Light Indicators The Installer can program the Reader s Light Indi cators to signal the System status at all times or al ternatively only in response to a Valid Key Light Indicators OFF when no Key is present comply with 50
19. gt ON to Enable the Key 5 Press ESC to go back to step 4 46 Expandable Hybrid Control Panel ABSOLUTA View m View LOG 3 1 You can view the event in the logger as follow 1 Press A or B to view the View LOG option 2 Press ENTER to select the option 3 Press 1 to view the events from the last and skip to step 5 or press 2 to view the events from a specific date and time 4 Enter the required Data and Time to start to view the events then press ENTER gt the display top line shows the order number of the event gt the display bottom line shows the event description 5 Press A and B to scroll the events Press C and D to scroll the details of the event The display top line shows the detail name on the right as follow gt WHO depending on the event the Zone the Key Card Tag the Wireless Key or the Super Key that had generated the event gt WHERE depending on the event the Wireless Re ceiver the RS232 port the USB port the Telephone Line the System the Panel the Keypad the Key reader the Expander In the Main Board the Ex pander Out or the Power Station where the event oc curred gt PARTIT depending on the event the involved Parti tions gt WHEN the date and time when the event has oc curred m Zone Status and Bypass 3 2 You can view the zone status standby alarm tamper short circuit bypassed included bypass the zones as follo
20. in Away Mode type in 13579013 then press ON If you want to Disarm Partition 13 using the same PIN type in 13579013 then press OFF you enter 13579013 then press A B Partition 13 will Arm in accordance with the respective configuration Notes on Arming from Keypads Before your system Arms your Control panel will check for the following conditions Active Detector Masked Zone Detector Fault Tamper Interconnection Fault Mains Fault Battery Fault Alarm Tx Fault Siren Fault Bypassed Zone Inactive zone WLS silent zone If you are operating from an LCD keypad these condi tions will be signalled in real time on the display If more Bypassed Zones or Inactive zones are present the display shows all alternately at intervals of two sec onds At this point you can do one of the following a Press the ENTER key and anyway perform the Arm ing request of control panel In the presence of Active Detectors zones you cannot force the arming it is necessary to remove the cause b press the ESC key to cancel the Arming request B Silencing Alarm Devices The quickest way to silence Alarm Signalling Devices Sirens and Flashers is to Disarm the system ps This operation will not interrupt the ongoing Alarm call or end the Alarm call cycle Therefore it will be necessary access the User Menu access allowed to Master User PINs only and stop the Alarm calls via the Clear Call Queue op
21. maintenance not requiring intervention on parts or connections Press Yes to confirm the request for Teleservice m Extra Time The panel is going to send an Extratime request to the system Would you like to proceed v Yes Xx No This option allows you to delay the auto arming by 1 hour see Arming Disarming Partitions gt Auto Arming for more information Press Yes to confirm the extraordinary request You can make up to extraordinary requests in a day 18 Expandable Hybrid Control Panel ABSOLUTA Stop Alarms The panel is going to stop all the alarms Would you like to proceed x Yes In general to turn off the visual audio sirens signalling devices simply disarm the partitions or clear the alarms If these two operations are not effective due to a permanent alarm condition or for some other reason the option Stop Alarms allows you to disable the signalling devices Press Yes to confirm the stop alarms the Control panel disable all signalling devices use The telephone actions voice calls SMS and the transmission of events to the Central Stations will NOT be disabled see Alarm Status gt Clear the transmission of events to cancel the telephone actions If option EN50131 is ENABLED on the keypad the sig nalling devices will be disabled until a new event occurs that activates them alarm tamper or fault If option EN50131 is disabled on the k
22. the alarm will go off in less than 10 seconds At the end of the disarming operation the keypad dis plays the Standby Screen Disarm Armed ten STAY type ET ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 11 B Disarm under Duress If you are forced to disarm the system under duress use the PIN the installer assigned for the purpose ask your installer for more information in that way the con trol panel will send a silent alarm NOT signalled by any audible device and by the keypads to competent authorities m Disarm for patrol Use the PIN assigned for this function ask your installer for more information to disarm the Partitions for a lim ited period of time Partitions will re arm automatically when the time programmed expires B Disarming with several PINs Keys If the installer has programmed disarming using several PINs Keys for a Partition to disarm it you must en ter use the PIN Key number assigned before the pro grammed time expires as described below also read the same paragraph under OPERATIONS FROM LCD KEYPAD gt Basic Arming Commands and Reader Operations 1 Disarm the Partitions as described in Disarming F F TT Required others PIN or Keys The display shows time available to use another PIN or Key 2 Disarm the Partitions again using a different PIN or Key before time available expires 2 0 ET System disar
23. 131 Multiple Systems The Keys can be programmed by the Installer to oper ate on more than one System and to manage different Partitions on each System Key operations The Keys can No Action Disarm Away Arm Arm A Mode Arm B Mode Patrol Disarm B No Action This operation keeps the Partitions status as the one that was theirs before the Key was brought close to the Reader 1 Hold the Key near the sensitive field of the Reader 2 Remove the Key when ALL the light indicators are blinking slowly about 10 seconds in EN50131 mode the Reader will show the Areas status mo mentarily 92 Expandable Hybrid Control Panel ABSOLUTA B Disarm This operation will Disarm all the Partitions common to both the Digital Key and Reader in use 1 Hold the Key near the sensitive field of the Reader the Green light indicator will blink briefly to show that the Partitions have been disarmed 2 Remove the Key when ALL the light indicators turn OFF Figure 5a During the programming phase the Installer enable or not the Key to clear the Partition calls or Control Panel calls when the system will be dis armed Multi PIN Key Disarming If the installer has pro grammed the multi PIN Key disarming for a Partition you need to enter use the number of programmed PINs Keys to disarm the Partition before the pro grammed time expires as follow read also the same paragr
24. 14 7 V Call the Installer The Mains power of the Power station x has failed Switching power supply of the Power station x does not work Call the Installer The Power station xis not capable to supply the right output voltage Call the Installer The battery of the Power station x is disconnected when you switch on the Power sta tion x Call the Installer Switching power supply of the Power station x is disconnected Call the Installer Short circuit on Output y of the Power station x Call the Installer The Control panel Clock has been set unset to Daylight savings time Fuse B is opened protects the Siren Output Zone Fuse is opened protects the Zones power line BPI Fuse is opened protects the BPI line Keybus Fuse is opened protects the Key bus The date of the periodic checks of the Installer has expired The date of the periodic checks of the Central Station has expired The Mains power of the Control panel has failed and the internal clock went to the de fault hour date Reprogramming Hour Date The control panel programming has been changed The zone Inactivity Time has expired from when the status zone is changed Telephone line failure A telephone message failed to reach destination Low Battery on one or more Wireless devices The GSM network cannot be found wait for it to be reset The SIM cannot be found contact your install
25. 2 Press ENTER to perform the ALARM Reset 3 Press ENTER again to execute the option or ESC to go back Press ESC to return to the User menu If Alarm signalling persists after the Alarms Reset op tion the causes of persistent Alarms must be cleared immediately While you are viewing the list of Alarm zones you can press OFF the keypad directly will manage the previous procedure of Alarm Reset A Master User PIN ONLY can restore all Alarms and Tampers and delete all Alarm and Tamper memories m Extra Time Request 1 2 If the Auto arm option is enabled and the system is grammed to Arm automatically at a preset time the Extra Time request will allow you to postpone the Auto arming event of 1 hour f any of the Partitions concerned is unable to im plement the Extra Time request the Keypad will emit an audible error signal Boop You can require up to 3 Extra Time Request in a day to add further time to stay in the protected area pz f the Auto Arm option has been disabled refer to Auto arm Enable Disable in this section the Overtime request will be ignored however the keypad will still emit a beep 1 Press to view the Extratime requ option 2 Press ENTER to select the option 3 Press ENTER to confirm Acceptance of the Extra time Request will be confirmed by an audible feed back signal and the above message 4 P
26. EL SECU RITY site www bentelsecurity com the App Store https itunes apple com or the Google Play Store https play google com store In order to manage the Control Panel using the ABSOLUTA APP the user must know the IMEI of the GSM Module installed on their Control Panel See gt KEYPAD OPERATIONS gt View gt GSM Module Status gt SMS OPERATIONS gt GSM Module IMEI Request APPENDIX Arming block conditions The Table 10 on the next pages shows the conditions that prevent the system arming as they are reported Feedback and if you can force the arming ARM in different operation modes 50131 ABSOLUTA APPENDIX 63 Blocking Condition Already Armed Bypassed Zone Already Disarmed Masked Zone Tampered Zone Failed Interconnection Battery Fault Communicator Fault System Tamper Request already done Active Auto bypassed Zone Yes Keyfob Low Battery Wireless Zone Fault Y Display Mess Mess Em Mess Em Mess Keypad Keyfob Feedback Feedback Yes Fast Blink Yes 2 Squawk No Display Mess No Fast Blink Yes 2 Squawk No Fast Blink Display Mess LEDON Yes Squawk Yes esi Mess Mess erie Mess Denia EGER Em Desk Mess Display Mess Mess poa Mess Wa Mess Mess Dla mess Mess LED Yes Yes 2Squawk No DisplayMess LEDON Yes Squawk Ye
27. GSM status request remaining credit and SMS reading display status and IP information view info for ABSOLUTA Exit ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 15 1 Menu option is ONLY available to Master Us ers This option is replaced by the PIN option for Normal Limited and Patrol Users 2 The Limited and Patrol Users CANNOT change their PIN 3 The Limited and Patrol Users CANNOT select the option Scenarios 4 Normal Limited and Patrol Users CANNOT change status of a single Partition 5 The Patrol User CANNOT bypass zones 6 The option History is NOT visible to the Patrol User 7 The Limited and Patrol Users CANNOT select the GSMIIP option To view the Menu Bar you must enter the Home Screen as described in Entering the Home Screen Press amp to view hide the Menu Bar Select the desired option and read the corresponding Menu Privacy Enable this option to allow the Installer to access the telephone agenda for j Info voice calls and export the user codes and user Keys Auto Arming 1 Current Menu 2 Press to go up a level in the menu structure 3 ltem selected Press Exit to quit the Home Screen Menu User Menu us This menu is ONLY accessible to Master Users This menu groups the following options gt PIN to set enable disable PINs gt Keys to disable ena
28. Keypad ABSOLUTA control panel supports both the new key readers of the ECLIPSE 2 series and the previous versions of ECLIPSE series BENTEL SECURITY srl reserves the right to change the technical specifications of this product without prior notice INTRODUCTION Glossary Keypads parts Models OPERATIONS FROM TOUCH KEYPAD Emergency Keys Entering the Home Screen Failed to access Arming Disarming Partitions Arming Disarming Disarm under Duress Disarm for patrol Disarming with several PINs Keys Auto arming Arming Block Conditions Alarm Status Clear the transmission of events Viewing Signals Menu Bar Menu User PIN Keys Numbers Teleservice Extra Time Stop Alarms Restore Alarms Settings Alarm Test Date and Time System Privacy Answering Installer Auto arming GSM Keypad Backlight Buzzer Control Picture Frame Clock Mode Clean Mode Background Image Language Scrolling Text Scenarios Info Partition Status Zone Status Events Buffer Installer Bentel Security TABLE CONTENTS GSM IP GSM SMS Credit Balance Received SMS IP APP Screen Calibration OPERATIONS FROM LCD KEYPAD Adjusting Volume Brightness Contrast Adjusting Buzzer Volume Contrast Adjustment Brightness adjustment LEDs and signals on Keypads LEDs and signals Display View Signals View Partition status Fast Keys Superkeys Basic Arming Commands Arming lt PIN gt ON Disarmi
29. NS The ABSOLUTA control panel supports the following Readers ECLIPSE2 Proximity Reader Figure 4b it has a sensitivity field where you must held the Key to per form the required operation gt PROXI Proximity Reader Figure 4d like the ECLIPSE2 Reader it has a sensitivity field where you must held the Key to perform the required opera tion Proximity Reader integrated on the PREMIUM Key pad Figure 4e these Keypads have built in Proxim ity Reader able to detect a Key held in its sensitivity field ps The ABSOLUTA Control Panel supports also the ECLIPSE Reader If you use this Reader be sure that its LEDs show the required status before re leasing the inside switch ABSOLUTA manages up to 32 Readers The Installer will program the following options for each Reader gt Partitions the Reader can control Reader Parti tions A Mode Arming AMBER B Mode Arming GREEN d Proxi sensitive field ECLIPSE2 sensitive field e Proxi sensitive field Figure 4 a SAT Digital key b ECLIPSE2 key reader c PROXI CARD card d PROXI reader e PREMIUM LCD key pad f Tag ABSOLUTA READER OPERATIONS 51 Digital Key The ABSOLUTA control panel supports the following Digital Keys gt SAT Proximity Key Figure 4a it is able to work with all the
30. OLUTA can manage the PREMIUM LCD CLASSIKA LCD and ABSOLUTA T Line Keypads Figure 1 Adjusting Volume Brightness Contrast Adjusting Buzzer Volume The Buzzer inside the LED and the LCD Keypad will emit an audible signal each time a valid key is pressed and if enabled by your Installer will also signal the Exit Time signalled by slow beeps the Entry Time signalled by fast beeps errors or Invalid requests sig nalled by a Buzz request Accepted or Done long beep violation of a Chime zone key Card program ming done Auto arm Timeout To adjust the volume of the internal buzzer 1 Press and hold the ESC key the internal buzzer will start sounding a series of beeps in such manner that the opera tor could hear the sound level in real time Release the ESC key 2a To increase the volume press the A key a number of times and or hold until the desired level is obtained 2b To lower the volume press more times and or hold B key until the desired level is obtained 3 To confirm the chosen level press the ENTER key or wait a few seconds for the keypad to return to the inactive state The buzzer will still emit sound alerts at extremely low volume even if it has been set to zero m Contrast Adjustment To adjust the contrast of the LCD display press and hold gt C to decrease contrast gt D to increase contrast To confirm the selected levels press ENTER or simply wait a few seconds a
31. Readers gt PROXI CARD Card Figure 4c it is able to work with all the Readers gt MINIPROXI Tag Figure 4f it is able to work with all the Readers When you present a Key to the Reader s sensitivity field you can perform the operations described in this section Each Key has a random code selected from over 4 bil lion combinations that ensure an high security grade Your Installer during the programming phase enrolls the Keys that you can use on the system and assigns their a label to identify the relative user in this way you can recognize in the Event Logger who does what The ABSOLUTA control panel supports up to 250 Keys Also the Keys are programmed to operate on specific Partitions as per the Readers In this Manual the word Key refers to the Sat Key the PROXI CARD Card and the MINI PROXI Tag and the word Reader refers to the ECLIPSE2 and PROXI Readers and the Proximity Reader inside the PREMIUM Keypad unless otherwise stated The Reader s Light Indicators The Readers have 3 light indicators that operate de pending if the Key is present on the Reader or not B Key at Reader When a Key is detected by the Reader the light indica tors will signal as follows Fast Blinking on ALL the Light Indicators this will occur when a False Key is present at the Reader Slow Blinking on ALL the Light Indicators this will occurs when not programmed keys with PATROL option is near the sensitive
32. Text gt gt PIN a User PIN enabled to manage the control panel by SMS gt ON activates the event OFF deactivates the event gt Command String the string programmed by the staller which is NOT case sensitive see the Com mand String column in Table 7 gt Text additional text that can be used to assign a de scription to the command message and is ignored by the control panel The event is activated and deactivated ONLY if the PIN and the event share at least one Partition see the Partitions column in Table 7 Phone Numbers ABSOLUTA SMS OPERATIONS 59 Partition Status You can check on the status of the control panel s Parti tions by sending the following SMS to the control panel s GSM number ABS A lt PIN gt lt Text gt gt PIN a User PIN enabled to manage the control panel by SMS gt Text an additional text that can be used to assign a description to the command message and is ignored by the control panel The control panel will respond with the following SMS ABS A lt SMS Label gt lt A P Z D t gt lt SMS La bel gt lt A P Z D t gt SMS Label the code assigned to the Partition by the in staller see table below A P Z D t the Partition s status as described Ta ble 3 on page 33 N Partition Label SMS Label 440214 2 2 14 2 pap pap 6042 7 4
33. aph on Basic Arming Commands 1 Entera valid PIN then press OFF or hold a valid Key near the sensitive field of the Reader the Green light indicator blinks few seconds then the Red light indicator turns ON indicating that you need to use another PIN Key to disarm the Partitions iH before enter another valid PIN then press OFF or hold another valid Key near the sensitive field of the Reader the Red light indicator turns OFF indicating the Partition disarming otherwise the Green light indicator blinks few seconds and the Red light indicator stay ON indicating that you need another PIN Key to disarm the Partitions iH before enter another valid PIN then press OFF or hold another valid Key near the sensitive field of the Reader the Red light indicator turns OFF indicating the Partition disarming A B C WV Figure 5 Disarm Arm from ECLIPSE2 reader B Away Arm This operation will Arm all the Partitions common to both the Key and Reader in use 1 Hold the Key near the sensitive field of the Reader 2 Remove the Key when the Red indicator light turns ON Figure 5b fone ofthe programmed block conditions for Arm ing is active you cannot Arm the three light indi cators first flash one at a time and then begin to flash all together comply with EN50131 for the Reader all light indicators will be switched off to hide the control panel status if the relative optio
34. artitions OFF alarms or Tamper active ON Atleast one Alarm or Tamper active Slow Blinking A Alarm Partition and Tampers are in memory restored When the Keypad s Partitions are disarmed it signals no info to communicate When the 5 Partitions are disarmed it signals Alarms Tampers Troubles Bypassed Zones if the Keypad is in Standby Status Troubles in the View Partition Status mode When a Keypad s Partitions is armed this LED is disabled Slow Blinking A troubles in memory restored The zone Alarm and Tamper events signalled on the LEDs refer to zones which belong to the keypad Partitions Table 2 LCD keypad INITIAL MODE DESCRIPTION Away system will turn ON the perimeter and internal zones of the respective Partition Stay The system will turn ON the perimeter zones of the respective Partition and will leave the internal zones OFF EB Stay 0 Delay The system will turn ON the perimeter zones of the respective Partition and will leave the internal zones OFF and will remove the Entry Time from zones which have one Disarm system will turn OFF the perimeter and internal zones of the respective Partition Test At least one zone is in Test status for the relative partition Alarm Partition corresponding partition is in Alarm Status Alarm Memory corresponding partition has an Alarm in memory If the partition is selected the letters will blink Table 3 Arming
35. be delayed if there are other calls in the queue or may be lost if the queue is full or there are problems with the GSM network Credit Check You can check on the credit remaining for the SIM in the control panel by sending the following SMS to the con trol panel s GSM number HABS HC H lt PIN gt lt T ext gt gt PIN a User PIN enabled to manage the control panel by SMS gt Text additional text that can be used to assign a de scription to the command message and is ignored by the control panel The control panel will forward the message received from the mobile telephone operator to the telephone number from which the request was made use The SMS sent in reply may be delayed if there are other calls in the queue or may be lost if the queue is fullor there are problems with the GSM network us If programmed to do so by the installer the credit message will be forwarded periodically to the first number in the Phonebook ps The credit remaining can also be checked from an LCD keypad as described in the section OPERATING YOUR SYSTEM FROM KEYPAD gt View gt GSM Module Status 3 3 Disabling a PIN You can disable your PIN by sending the following SMS to the control panel s GSM number ABS BLOCK lt PIN gt lt Text gt gt PIN a User PIN enabled to manage the control panel by SMS gt Text additional text that can be used to assign a de scription to the command message and is ig
36. ble Keys and Wireless keys gt Numbers to set Telephone Numbers gt Settings groups the options Alarm Test Date Time System and Keypad gt Teleservice to request installer assistance via phone gt Extra Time to postpone auto arming gt Stop Alarms to disable visual audio sirens signal ling devices gt Restore Alarms to re activate visual audio sirens signalling devices Select the desired option and read the corresponding paragraph B PIN Menu This option allows you to set and enable disable User PINs Default ONLY User PIN 1 is Enabled and is 0007 The display s left side shows available PINs with their labels in groups of four use Available PINs and labels set by the installer 16 Expandable Hybrid Control Panel ABSOLUTA 1 Press WA or to scroll the PIN list then select the PIN to be changed For Normal and Limited Users the PIN list only shows the PIN used to login The display s right side shows the PIN selected and its status Enabled Disable 2 Press Disable to disable the PIN or Enabled to en able the PIN 3 Ifthe PIN is enabled press New PIN to change the PIN and go to the next step if the installer has set automatic PIN generation otherwise go to step 5 The display shows the PIN generated automatically Auto Generate PIN 39090 w Confirm write down or memorize this number 4 Memo
37. dule Menu Sat Mar 09 2013 16 54 scenarios Your available balance to 10 07 2013 at 16 54 N 16 53 is 14 72 EUR 0 30 EUR last charge iM To control the traffic sign up vodafone com Info Sat Ma 99 2013 Sat Mar 09 2013 The display s left side shows the list of messages re ceived gt showing the time and number that sent the message gt if the number is found in the Control Panel Phone Book the associated label is displayed gt UNREAD messages are displayed in bold The GSM Module can memorise 32 messages Ifa new message arrives when the GSM Module al ready contains 32 messages in its memory the old est message is deleted to make room for the new message 2 Press to scroll messages then touch the message wanted to read its content in the centre of the display 3 Press Delete to cancel the message Are you sure you want to delete the SMS X No 4 Press Yes to confirm and No to cancel Menu Ccenarios ABSSRV Local IP Info 192 168 0 108 P MAC Address 4 MAC 00034F06FFD5 GSM IP The central part of the display shows gt ABSSRV if the Absoluta Server is enabled and ac cessible gt NO ABSSRV if the Absoluta Server is disabled ABSSRV FAULT if the Absoluta Server is NOT ac cessible Local IP the IP address of the IP Module MAC the MAC address of the IP Module Menu Scenarios Info
38. e and time 4 Press ENTER to view message text the message starts scrolling automatically on the display s lower line 5 Press gt C to block automatic scrolling and to scroll the mes sage manually from right to left gt D to scroll the message manually from left to right gt ON to start automatic scrolling again from left to right 6 Press OFF to delete the message 7 Press ENTER to confirm and return to step 3 or ESC to cancel and return to step 4 48 Expandable Hybrid Control Panel ABSOLUTA m IP Module status 3 5 This option allows you to view the Module s status 1 Press A or B to view IP Status 2 Press ENTER to select the option The display shows the Absoluta Server status on the upper row gt ABSSRV if the Server is enabled and obtainable gt NO ABSSRV if the Server is disabled gt ABSSRV FAULT if the Server is NOT obtainable Shows the Module IP address on the lower row If there are problems the display shows on the upper row IP and on the right gt LinkLOST if the Module cannot see the LAN net work gt FAULT if the Control Panel cannot see the Module gt Wrong FW if the module firmware is not compatible with the Control Panel gt DISABLED if the module is disable 3 Press OFF or ON respectively to disable or enable the Module nen mg is disabled the display shows on the upper row and f on the rower row if
39. e are any conditions that prevent Partition arming Battery 4 Cancel Press Force to the Partitions case Cancel to cancel arming Based on the Keypad function mode EN50131 en abled disabled some Blocking Conditions CANNOT be forced read APPENDIX gt Arming Block Conditions for more information some Blocking Conditions can be solved by the user others require installer intervention Alarm Status The Alarm Status is signalled by means set by the in staller gt visible and or audible devices sirens gt voice calls and or SMS sent to a programmed series of numbers gt transmission of events to central stations The Keypad signals the Alarm Status with the message System in Alarm above a red bar and the icon If option 50131 is disabled the Alarm Status is also visible from the Standby Status System in Alarm 12 29 Saturday March 9 2013 ge 2 e _ e O e e Otherwise if the EN50131 option the Alarm Status is ONLY visible in the Home Screen System in Alarm TN 11 57 Thursday April 17 2014 STAY type A A ty pe amp Disarm Partitions as described d in Arming Disarming Partitions to end the Alarm Status The Control panel carries on to transmit pro grammed events voice calls SMS and transmis sion of events to the Central Stations even after the
40. e display shows tc ramier contact the in staller 4 Press ENTER to display the IMEI of the GSM Module 5 Press ENTER to check on your remaining credit 6 Press ENTER to confirm and the control panel will send an SMS message to check on the credit re maining 7 Read Display SMS 3 4 for the instructions on how read the SMS messages B Display SMS 3 4 This option allows you to read the SMS received by the GSM Module ps The GSM Module can memorise 32 messages If a new message arrives when the GSM Module already contains 32 messages in its memory the oldest mes sage is deleted to make room for the new message ps The control panel does NOT save SMS activating or deactivating events HABS E disabling the PIN HABS BLOCK requesting a check on the credit remaining ABS C for the Partition Sta tus request fABS A for arming disarming the Partitions HABS A or ABS AF48 1 Press A or B to show Display SMS 2 Press ENTER to select the option The gt So isplay shows fis where x is the message number dis played and is the number of messages received gt an asterisk if the message has not been read and on the lower line gt the number that sent the message p f the number is memorised in the control panel phone book the number s label is shown 3 Press A or B to scroll messages then press ENTER to view message reception dat
41. ed um 3 STAY type A S STAY type S STAY type STAY type D The keypad displays the Home Screen described be low 1 Signals Icon This icon signals alarms tampering failures or bypassed zones in progress or memorised it changes based on whether the signal is in progress or memory touch this icon to display signals as de scribed in Viewing Signals 2 Unread SMS Icon This icon signals the presence of SMSs that have not been read the number to the top right indicates the number of SMSs to be read touch this icon to read them only Master and Normal Users as described in Received SMS 3 Event Transmission Icon This icon signals that the control panel is transmitting the events Alarm Tamper Fault or Generic through its communication channels voice calls SMS transmissions to the Cen tral Stations touch this icon to cancel the transmission in progress and those queuing as described in Alarm Status gt Clear the transmission of events 4 Status Bar This zone can show the following mes sages with decreasing priority System in Alarm above a red bar in an alarm read Alarm Status for more information Auto arm in above an orange bar if the system is about to be armed by the time scheduler read Auto arming for more information 5 Stop Alarms This icon indicates that the visual au 4 5 6 dio sirens signalling devices have been disabled by t
42. eived SMS for more information 4 Time and Date This area displays the current time and date read Settings Date and Time for more in formation 5 Stop Alarms If option EN50131 is disabled this area displays the ks icon when the visual audio sirens signal ling devices are disabled via the Stop Alarms option see Menu User Stop Alarms for more information The icon is also displayed when option EN50131 is enabled if the signalling devices are disabled by the jumper SERV ask your installer for more information 6 Arm Status This area can show the following icons if the 50131 option is disabled gt all Keypad Partitions are disarmed gt if at least Partition is armed 7 Auto arming EN50131 is disabled this area displays the icon when the auto arming is en abled see System gt Auto arming for more information 8 Partition Status If option EN50131 is disabled this area displays the ag status of the keypad when icon is pressed gt Press or PS to scroll through the partitions Press icon 6 a or to hide the partition status 9 User Logged in LED green If on indicates that the user is logged in to the keypad read Entering the Home Screen for more information 10 Armed Partition LED red Ifthe EN50131 option is disabled comes on when at least one keypad Parti tion is armed read Arming Disa
43. el will re spond with the following SMS see Partition Status ABS A lt SMS Label gt lt I P Z D t gt lt SMS La bel I PIZ D t I If the operation fails due to any Blocking Conditions that are forced the Control Panel will respond with the following SMS HABSHAF lt PIN gt lt OFF OF ON A B C D gt lt space gt Execute anyway lt space gt lt Blocking condi tion gt lt space gt lt Blocking condition gt lt gt gt PIN the same PIN used in the SMS for the Arm ing Disarming request gt OFF OF ON A B C D the same option used in the SMS for the Arming Disarming request gt Blocking Condition a condition that prevents the arming of the Partitions see APPENDIX gt Arming Blocking Conditions gt indicates that there are other Blocking Conditions that cannot be displayed as the SMS is too long The above SMS be forwarded to the GSM number of the Control Panel to force the arming If the operation fails due to Blocking Conditions that CANNOT be forced the Control Panel responds with the following SMS Not allowed space Blocking condi 60 Expandable Hybrid Control Panel ABSOLUTA gt Blocking Condition condition that prevents the arming of the Partitions see APPENDIX gt Arming Blocking Conditions indicates that there are other Blocking Conditions that cannot be displayed as the SMS is too long ps The SMS sent in reply may
44. eless Key in use m Stay Arming M Press the button until the LED turns ON see Fig 6 to Arm the system in A Mode B Disarming 9 Press the button until the LED turns ON see Fig 6 to Disarm all the Partitions of the Wireless Key in use m Other functions Press the button until the LED turns ON see Fig 6 to activate the special functions programmed for the Wire less Key in use example B Mode arming Superkey or both B Low Battery If any of the Wireless Key batteries starts to run low the LED on the Keypads will Turn ON All the system Trouble conditions signalled by the LED Therefore if this LED turns ON you must access the View Trouble Mode for details The Low Wireless Battery i a S Shale View Trouble Mode by the i message refer to View Trouble Mode in Lina OPERATING YOUR SYSTEM FROM A KEYPAD section The Event Logger will provide the details of the Wire less key that has triggered the Low battery condition 0 In accordance with the EN50131 1 standard the system does not arm if there is a low battery condi tion when you perform an arming request the ex ternal siren will emit a double squawk You can verify the cause that inhibits the arming low bat tery through an LCD keypad and force the arm ing the external siren will emit a squawk to signal the arming Call your installer and have the battery replaced o4 Expandable H
45. emove dust accumulation on the panel container with a damp cloth without use any type of solvent Check the status of the connections and wires Check inside the panel there are no foreign bodies For other security system devices such as smoke detectors infrared and microwave detectors and inertial detectors refer to the instructions for maintenance and testing RECYCLING INFORMATION BENTEL SECURITY recommends that customers dispose of their used equipment panels detectors sirens and other devices in an environmentally sound manner Potential methods include reuse of parts or whole products and recycling of products components and or materials For specific information see http www bentelsecurity com index php o environmental ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE DIRECTIVE the European Union this label indicates that this product NOT be disposed of with household waste It should be deposited at an appropriate facility to enable recovery and recycling For specific information see http www bentelsecurity com index php o environmental NOTE In addition to User Manual the Installation Manual is also available for the ABSOLUTA control panel This manuals may be purchased separately or downloaded free of charge from the BENTEL SECURITY website www bentelsecurity com The control keypads of ABSOLUTA control panel are the CLASSIKA and PREMIUM LCD ABSOLUTA T Line and the ABSOLUTA M Touch touchscreen
46. enarios EIFE CIN type B Y type C GSM IP Y typeDy The Menu Bar will allow you to spice the following Op tions Menu 1 2 setting enabling disabling PIN numbers Number programming Telephone Numbers disabling Keys Wireless keys Teleservice request for assistance remotely Setting Alarm Test tests signalling devices Date Time setting date and time System Privacy installer enabled to set Tele phone Numbers and export Answering enabling management via phone of the control panel nstaller enabling installer Auto arming enabling automatic arming GSM enabling GSM Keypad Backlight regulation of display bright ness Control regulation of buzzer vol ume Picture Frame choice of photo for the Digital Frame Clock Mode display of 12 24 hour clock Clean Mode display cleaning Background Image select background image Language select keypad language Scrolling Test disabling scrolling text Scenarios 3 Outputs activate deactivate outputs Actions activate deactivate actions Info Partition Status 4 view and modify Partition status 4Zone Status 5 view Zone status and bypass Event Buffer 6 view events memorised nstaller display master data installer Bentel Security display information about Bentel Security GSMIIP 7 GSM view
47. enter use the number of programmed PINs Keys to disarm the Partition before the pro grammed time expires as follow read also the same paragraph on Key operations 1 Enter a valid PIN then press OFF or use a valid Key iM before enter another valid PIN then press OFF or use another valid Key the display shows the following message if no other PIN Key is required otherwise shows the following message iH before enter another valid PIN then press OFF or use another valid Key the Partitions disarm ABSOLUTA OPERATIONS FROM LCD KEYPAD 99 B A B C and D Arming lt gt B D ON DO NOT assign Duress PINs to A B or D Mode Arming commands Each user PIN can be set up to manage four different Arming mode configurations A B C and D These con figurations determine the Partitions that will Arm and those that will Disarm when an A B C or D Mode com mand ON to confirm the choise is entered at Key pad the final configuration depends on the User PIN and Keypad Partitions Keypads can operate ONLY on the Partitions they are assigned to You can Arm Disarm the Partitions separately us ing a 6 digit User PIN as follows type in a 6 digit User PIN followed by the 2 digit ID number of the Partition concerned then press ON OFF A as required Example If the 6 digit User PIN is 135790 and you want to Arm Partition 13
48. er The GPRS network cannot be found wait for it to be reset Table 6 List of Faults 34 Expandable Hybrid Control Panel ABSOLUTA Basic Arming Commands You can control seven basic commands from standby status by typing in your PIN and pressing the respective keys refer to the following Table Access to ALL com mands require entry a valid User PIN A The Factory Default Master User PIN 0001 must be changed for security reasons refer to Change my PIN in this section Key sequence from standby status PIN OFF Disarm PIN ON Arm PIN A ON A Mode Arm PIN B ON Mode Arm PIN C ON C Mode Arm PIN D ON D Mode Arm PIN ENTER View Area status If there are no Troubles From the View Area status or Trouble screen press ENTER to ac cess the User menu COMMAND Commands will affect only the Partitions common to both the User PIN and Keypad concerned com mon Partitions Invalid commands will be signalled by a buzz and the following message Invalid commands may be due to the User PIN Keypad Partitions f you do not press key within 30 seconds the key pad will revert automatically to standby status except during the input of the PIN If the input is not com pleted the display keypad will show WRONG PIN after one minute The User can ENTER the following commands at the Keypad B Arming l
49. er of the partition will blink if the partition has in memory an Alarm or Tamper 12345678 711 ve us The keypad will stay the View Partition status for 30 s max and then return to the standby status During the View Partition status it is possible to per form the basic operations Press D and C to scroll the Keypad s Partitions Press OFF to Disarm the Partition gt ON to Arm the Partition in Away Mode Athen ON to Arm the Partition in Stay Mode Bthen ON to Arm the Partition in Instant Stay Mode The first 8 characters on the LCD bottom line show the status of the Keypad Partitions Table 3 The characters n 9 to 13 on the LCD bottom line show the trouble conditions Table 4 The last 3 characters on the LCD bottom line show the Installer status Answering Machine and Telephone line Table 5 The numbers below the display will correspond only to the first 8 Partitions Press ESC to quit the View Partition status After a few seconds the Keypad go back to standby status Scheduler enabled if blinking Date e Time Status ENT Tampers 123456758Ta 15132 Controls Figure 3 The display of a LCD keypad during View partition status MAIN PAGE 32 Expandable Hybrid Control Panel ABSOLUTA DESCRIPTION OFF All the keypad Partitions are Disarmed ON At least one of the keypad Partitions is Armed Slow Blinking During the selection of p
50. eservice 2 2 This option will allow you to Enable Disable the In staller to access the panel locally using the keypad In staller Level default and remotely by Teleservice calls and PIN Transfer ask the Installer os The Installer CANNOT be enabled disabled during a session 1 Press Aor B to view the ON OFF Installer option 2 Press gt OFF to disable the Installer access gt ON to enable the Installer access 3 Ifthe Installer is enabled press ENTER to proceed to the next step otherwise press ESC to return to the User menu 4 Press gt ON to enable PIN Transfer gt OFF to disable PIN Transfer 5 Press ESC to return to the User Menu m Auto Arm 2 3 Your Installer may have set up Partitions to turn ON OFF at preset times scheduler The Auto Arm option will disarm the Partitions at set time even if they are in alarm status This option will allow you to turn the Scheduler ON OFF If ON on the LCD keypads a star will blink near the time 1 Press A or B to view the ON OFF Auto Arm option 2 Press ON to Enable the Scheduler OFF to Disable the Scheduler 3 Press the ESC to step back to the User menu ABSOLUTA OPERATIONS FROM LCD KEYPAD 43 m Date Time 2 4 This option will allow you to set the current Date and Time 1 Press Aor B to view the Date Time option 2 Press ENTER to select the option
51. etector enrolled on the zone has not been communicating for some time con tact the installer Standby the zone operates regularly f several statuses are present at the same time the icon for the status with highest priority is dis played Zone Test Using the Zone Status option you can ver ify the operation of the intrusion detectors and panic buttons without setting off unwanted alarms as de scribed below 1 Bypass the zones that you want to test 2 Activate the bypassed zones open doors windows move in front of the motion detectors press the panic buttons etc 3 Make sure that the Zone Status window displays Open when you activate a zone 4 Remember to unbypass the bypassed zones B Events Buffer 7 op 9 O o o Menu Event Buffer dit ceu Eq This option allows you to view events memorised in the Log The display s left side lists the events starting from the most recent It shows the day and month the event occurred gt the symbol Y if an event has been restored the name of the event 1 Press if you just want to see events older than a certain date and time Menu 4 5 2 Select the desired date and time and press Go to 1 Press MM or to scroll the list event 2 Press Bypass to bypass the zone press Resume to include the zone ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 2
52. eypad the sig nalling devices remain disabled until they are enabled again using the option Restore Alarms as described in the following paragraph in this case icon Z will signal the permanent disarming of the signalling devices B Restore Alarms The panel is going to restore all the alarms Would you like to x Yes This option allows you to re activate the visual audio sirens signalling devices with the option Stop Alarms disabled Press Yes to confirm the resetting of alarms the signal ling devices will be reactivated if the alarm conditions are still present Settings Settings Press gt Alarm Test to check that signal devices operate correctly gt DatelTime to set the date and time of the control panel gt System to enable disable the Privacy the Answer ing the Installer the Auto arming the GSM and the gt Keypad to adjust the Backlighting and the keypad Buzzer volume to choose images for the Digital Frame and Background to set the Clock operating mode and the keypad Language to Clean the keypad Read the relevant section for more information ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 19 m Alarm Test An alarm test will be performed on the system Would you like to proceed x Yes X No This option allows you to check signal system opera tions alarms When this option is selected Panel Output no 1 gener ally connected to the exter
53. ge appears if an invalid PIN is en tered The keypad blocks for 90 seconds if 10 consecu tive invalid PIN are entered Arming Disarming Partitions When a Partition is armed any violation of one of its Zones causes an alarm When a Partition is disarmed its zones can be violated without causing any alarms ps The 24h Zones cause an alarm independent of the status of Partitions they belong to they are gener ally used to detect security system device tamper ing and as fire detectors Operations described in this paragraph arm disarm ALL Partitions common to Keypad and PIN used as pro grammed by the installer ask the installer for more in formation Single Partitions can also be armed disarmed singly as described in Info Partition Status To arm disarm Partitions follow the instructions below Enter the Home Screen as described in Entering the Home Screen Z 2019 sees MUS 09 43 Saturday March 9 2013 Global s TAY type A STAY B STAY type C S STAY type D keypad displays the Home Screen described below 1 Arming Mode Displays Arming Modes available gt Global arms all Partitions common to Keypad and PIN used gt STAY type A B C D arms disarms the Partitions common to keypad and PIN used as programmed by the installer use The Global option is NOT displayed if the installer has not programmed at least one stay arming
54. he Green light indicator turns OFF when you re move the Key if the Key s Partitions does not match the Reader s Partitions For example if a Key is assigned to the Partition n 1 and a Reader is assigned to the Partitions n 1 and 2 the Green light indicator turns ON when you hold the Key near the Reader when you remove the Key from the Reader only the Partition n 1 arms in B Mode and the Green light indicator turns OFF B Disarm Patrol Keys with the Patrol option can Disarm the system for the programmed Patrol Time B False Key When an unrolled false Key is present at the Reader ALL the Readers light indicators fast blinking A Reader tamper will be generated if you present 10 time a false Key at the Reader LED Panasonic CR2025 SV Figure 6 Wireless key The Wireless Key If your system is equipped with a Wireless Receiver it will be possible to control all the main functions from re mote locations by means of Wireless Keys see Fig ure 6 This paragraph describes the functions that can be controlled by Wireless Keys use The operations performed by Wireless Keys will not be confirmed by any type of feed back signal audible or visual unless done in the vicinity of a Reader or a Keypad or a device that has been es pecially set up to provide feed back signals m Away Arming Press the button until the LED turns ON see Fig 6 to Arm all the Partitions of the Wir
55. he Key Wireless key ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 17 m Numbers This option allows you to set Telephone Numbers The display s left side shows Telephone Numbers avail able with their labels in groups of four Available Telephone Numbers and labels are set by the installer ONLY the Telephone Numbers that can be modi fied by the user are shown the numbers of the Central Stations are NOT shown 1 Press or amp to scroll the list of Telephone Num bers then select the Number to be changed the display s right side shows the Telephone Number selected 2 Press Edit to change the Telephone Number se lected User Phone 1 2 4 5 6 Delete INN 7 8 9 Save Esc Q the desired number gt press dash to enter a long 4 second pause indi cated by the dash gt press _ underscore to enter a short 2 second pause indicated by the underscore gt press Delete to cancel the last character gt press Reset to cancel ALL characters gt press Save to to save changes or ESC to maintain the previous Number and go back to step 1 DO NOT insert pauses in numbers dialled via GSM B Teleservice The panel is going to call Teleservice and you will logout from the system Would you like to proceed v Yes X No If your installer has preset Teleservice this option al lows you to request assistance remotely
56. he option Stop Alarms see Menu User gt Stop Alarms for more information or through the jumper Panic 7 9 SERV ask your installer for more information Emergency ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 9 6 Arming Disarming Keys These keys to arm disarm Partitions read Arming Disarming Parti tions for more information us The Patrol User can ONLY Away Arming and Disarming the system therefore these keys are NOT available to the Patrol User 7 Auto arming This icon indicates that auto arming is enabled see System gt Auto arming for more information Press 2 display hide the Menu Bar read Menu for more T x le T Menu 20 39 Saturday March 9 7013 Press Exit to quit the Home Screen or any other keypad screen and go back to step 2 The keypad quits automatically from the Home Screen from all other screens after 30 180 sec onds if no key is pressed Operations possible and information visible de pend on the type of PIN used to log in Master Nor mal or Limited or Patrol Operations related to Partitions and Zones will ONL Y be effective on Partitions and Zones of Parti tions common to the PIN and Keypad used use Each PIN and Keypad can ONLY display the infor mation in Partitions and Zones belonging to Parti tions common to the PIN and Keypad used Failed to access The following messa
57. hee are no problems or the aforemen tioned problems 4 Ifthe Module is enabled and there no problems press d to display its MAC address B ABSOLUTA INFO 3 6 This option allows you to view information on configur ing the ABSOLUTA App to manage the control panel through iPhone and Android smartphone 1 Press Aor B to view ABSOLUTA INFO 2 Press ENTER to select the option The line above of display shows the control panel ver sion in the exaple above the line below shows the serial number of the control panel in the example above The information displayed depends on the Control Panel you own 2 Ihe Absoluta Server supports the ABSOLUTA control panel in access to the Internet services remote service event notification via e mail and the ABSOLUTA app connection of the ABSOLUTA app to the Control Panel Ask your installer for more information ABSOLUTA OPERATIONS FROM LCD KEYPAD 49 Digital Keys will allow you to perform all the basic operations from enabled Readers The Reader Readers have 3 light indicators Red Amber and Green To comply with EN50131 30 seconds after every arming disarming the 3 light indicators will be switched off to hide the control unit status AK in order to comply with the EN50131 1 and 50131 3 standards EN50131 option must be enabled ask your installer PROXI LEDs READER OPERATIO
58. ice Mess Voice Mess Voice Mess Voice Mess Voice Mess No SMS No F SMSMess F Yes Dedicated Event No Lt BM t Ve None vo No Dedicated Event No Dedicated Event N No Dedicated Event No No SMSMess F Yes Noe _ Yes SMS Mess Yes Yes None Yes SMS Mess M E ves No Dedicated Event No Dedicated Event No SMSMess No No Dedicated Event No SMSMess No No Dedicated Event F SMSMess F Yes DedicatedEvent No F sMsMess F Yes _ None _ Yes F SMSMess No No E es Dedicated Event No Dedicated Event F SMSMess F Yes Noe F Yes Dedicated Event No F SMSMess F Yes _ Yes F SMSMess F F sMsMess F Yes _ Yes F SMSMess F F SMSMess F Yes F SMSMess F F sMsMess F Yes _ Yes F SMSMess No No F SMSMess F Yes _ Yes No SMSMess No No No SMSMess No No F SMSMess F Yes DedicatedEvent No F SMSMess F Yes None F SMSMess F F SMSMess F Yes F sMs Mess Yes DedicatedEvent No Yes DedicatedEvent No None Ye ves Dedicated Event No Dedicated Event No Dedicated Event No Dedicated Event Dedicated vent No Non Ye _ ves Dedicated Event No Squawk Yes Message No Voice Mess
59. igital Key An electronic control key with a random PIN selected from over 4 294 967 296 billion combina tions Display alphanumeric screen on the LCD Keypads LCD Keypad A command keypad with a display Your Control panel can be programmed and controlled via LCD Keypads Touch Keypad Touchscreen keypad to manage and program the Control Panel LED A small coloured light on the Keypads and Readers INTRODUCTION Log A list of the last 2000 events Partition A section of the premises Each Partition can have its own Times PINs and Digital Keys Cards etc Reader A peripheral control device which accepts commands from Digital Keys Cards e g PROXI Prox imity Reader ECLIPSE2 Readers Real time Instant Audible Visual signals or communi cations Telemonitoring A remote monitoring service provided by a Central Station This feature will allow the Control panel to transmit real time events e g Forced entry Tamper Alarms etc to the Central station Teleservice A remote maintenance service provided by your Installer The Teleservice feature allows the Installer to operate on your system over the phone remotely B Keypads parts Figure 1 shows the main components of the PREMIUM LCD CLASSIKA LCD and ABSOLUTA M Touch Keypads DESCRIPTION Function LEDs Display Keys Down flip Information chart Proximity Reader sensitive field Emergency Keys Arrow scroll keys
60. il the keypad beeps and displays the 4 icon about 4 seconds to signal a fire Panic Keep pressed until the keypad beeps and displays the 0 4 icon about 4 seconds to signal an aggression Emergency Keep this Kev pressed until the keypad beeps and displays the icon about 4 seconds to signal an emergency situation Actions triggered by the Emergency Keys Emergency Key labels depend on control panel pro gramming ask your installer for more information 8 Expandable Hybrid Control Panel ABSOLUTA Entering the Home Screen On standby the keypad display is off or displays images selected for the Digital Frame To carry out any operations you must access the key pad s Home Screen as described below 1 Press the Home key for at least 3 seconds and go to step 3 or touch any point on the display when it is off or displays Digital Frame images G oS 2 Touch any point on the display again when the standby status screen appears Enter PIN 1 2 3 M 5 6 Pan 7 9 US Emergency 0 The key is for access Installer or Level 4 mode If you touch this key by mistake touch it again to display the user Login Screen 3 Enter a valid PIN Enter PIN 1 2 3 4 Press gt cancel numbers entered A again to exit the Login Screen and go back to step 2 MJ to confirm the PIN enter
61. image to select deselect it the one selected is the one in the green frame use The image selected from the SD card is copied to the keypad memory so that the SD card can be re moved B Language Menu Setting Backlight Scenarios Language Selected Language Italiana Deutsch Into Nederlands Clean Mode Espa ol Background Image GSM IP Francais Portugu s Scrolling Text Exit Select the language to be used for keypad text When the keypad is first turned on the keypad lan guage is set as that of the control panel it is con nected to This option only changes the language of the key pad used 24 Expandable Hybrid Control Panel ABSOLUTA Scrolling Text Menu Setting Backlight Scrolling Text eas Buzzer Control Please select the mode Picture Frama 3 Info Clock Mode Clean Mode GSM IP Background Image Disabled Language This option allows you to disable enable the scrolling of programmable labels Arming Modes Zones Parti tions Outputs Telephone Numbers Users keys etc in case they are too long for the space provided gt press Disabled to disable scrolling gt press Enabled to enable scrolling Default Enabled Scenarios This option allows you to activate deactivate Control Panel Reserved Outputs and actions associated with Remote Command events
62. in Away mode 2 to Disarm the Partition 3 to Arm the Partition in Stay mode 4J to Arm the Partition in Stay with Zero Delay mode The partition status will be indicated by the following messages lt lt Armed gt gt Message 200 if any action of arming was successful lt lt Disarmed gt gt Message 201 if any action of disarm ing was successful lt lt Not ready action will not be executed gt gt Mes sage 204 if any action of arming has been refused lt lt Not ready press one to arm gt gt Message 205 if the partition is not ready to arm but it is possible to arm anyway If is pressed anyway to arm the messages will follow Message 200 The Partition will Arm Disarm immediately and the sys tem will go back to step 1 m Enable Disable Installer 5 This command will allow you to Enable Disable the In staller and Remote Service Press U to enable or J to disabled Installer gt If the installer has been enabled the disabled com mand will be communicate with a beep gt if the installer has been disabled the enabled com mand will be communicate with a beep m Clear call queue 7 If you accessing your system via Answering device mode press J to end the call Ifyou are accessing your system via Dialler mode after receiving an Alarm message press U to interrupt the ongoing Alarm and clear the call queue A beep will commu
63. le this option to allow the installer to access the phonebook for voice calls and to export user PINs and Keys us This option is disabled and CANNOT be enabled if the Installer option is disabled Press Enable to enable the option or Disable to disable the option 20 Expandable Hybrid Control Panel ABSOLUTA B Answering Setting Privacy LII y i enarics talla i Installer mmo Auto Arming This option will allow you to enable disable the Control Panel Answering device If the Answering Device is en abled the Control Panel will answer calls with a Voice Message your installer will have recorded the required messages for your system Press Enable to enable the option or Disable to disable it B installer Menu Setting Privacy Scenarios Answering Into Auto Arming This option allows you to enable disable the Installer Installer Level to operate locally on the keypad or re motely through Teleservice ps The Installer CANNOT be enabled disabled during a session Press Enable to enable the option or Disable to disable it B Auto arming Setting Privacy SEeNaros Answering Installer Info arm disarm the system at certain d 1 programmed time GSM IP Auto arm arms and disarms Partitions at times sched uled by the installer use The Auto arming option disarms Partitions at the scheduled time even if they are in an Alarm Sta
64. line shows the D ane ane me bottom line shows the message dio i After you have entered a valid PIN the Edicola boum line shows the Partition Status Figure 3 and Table 3 Troubles Table 4 and other in formation Table 5 bid line of the display reads iii when the GSM Module receives an SMS message See Display SMS 3 4 later in this chapter m View Signals Enter your User PIN default PIN 0001 and then press the ENTER key Comply 50131 option enabled if the Control panel has stored a Trouble or zone Alarm Tam per event alarm memory the LED is on The signals Trouble zone Alarm Tamper event and alarm memory will be shown in the following order after the ENTER key is pressed gt Alarms gt Tamper gt Troubles gt Bypassed zones gt Active zones To go back press the ESC key The first line of display will show the description of the zone concerned as follows 123456788 T T8938 If the Control panel has stored several troubles use A and B key to scroll the display During the View of Alarms Tampers and Faults you can press the OFF Key to activate the proce dure for their clearing Besides for Tampers and Faults only you can press 0 zero to Restart the procedure E View Partition status The View Partition status Keypads can operate ONLY on the Partitions they are assigned to and the relative charact
65. lk Listen in sessions can also be acti vated by the Personal Panic Button thus making this feature extremely useful in emergency situations in volving the elderly or disabled f you press J during the Two way Talk session the Control panel will switch to Listen in mode p fthe sound quality of the Two way Talk session is poor use the One way Talk and Listen in modes press J Press to reduce the remote microphone audio gain Press to centre the remote microphone audio gain gt Press 9 to increase the remote microphone audio gain B Zone Partitions status 2 This command will allow you to check the status of the Zones and of the Partitions The Zone and Partition Identifier number must al ways be 3 digits long If necessary enter the re quired 0 to fit 1 Press 2 to check the Zone and Partitions status 2 Press _J for Partition status or 2Jfor Zones status Partitions status Press in sequence to know the current status of the Partition 777 The Partition status will be indicated by the following messages lt lt Armed gt gt Message 200 if the Partition is armed lt lt Armed stay gt gt Message 201 if the Partition is armed in stay mode lt lt Armed stay with zero delay gt gt Message 202 if the Partition is armed in stay mode with 0 delay lt lt Disarmed gt gt Message 203 ifthe Partition is disarmed boop If Par
66. med The display message System Disarmed appears if other PINs or Keys are NOT needed otherwise it goes back to the previous step B Auto arming If your installer has programmed the Partitions to arm automatically they will be armed disarmed at sched uled times in scheduled modes ask your installer for more information Auto arming can be enabled disabled as de scribed in System gt Auto arming When there are just 10 minutes to go before a Partition is armed automatically the display in Standby Status shows the auto arming signalling bar with the count down of time remaining W P r o DS ay 14 01 Saturday Marcii 9 2013 220 90 009 5607 OOS n x x 2 520 2 40 9 You can postpone automatic arming by 1 hour as fol lows 1 Enter the Home Screen as described in Entering the Home Screen Mor _Time 14 01 Saturday March 9 2013 Global 2 Press More Time to postpone automatic arming by 1 hour or press OK to hide the auto arming notifica tion bar You can postpone automatic arming up to times in a day See Menu User gt Extra Time to postpone the auto arming when there are more than 10 minutes left before the scheduled time 12 Expandable Hybrid Control Panel ABSOLUTA B Arming Block Conditions The display shows a screen like this one if ther
67. mes sages one or more Outputs Up to 32 Telephone numbers can be programmed for the first two actions use Hold the Superkey for at least 4 seconds A beep of acceptance will follow The Superkeys are not ac tive by default ps Ask the installer to activate the Super keys DESCRIPTION The user PINs are NOT safe because they are the default factory ones Change the default PIN The installer has changed the programming of the control panel The Battery voltage of the Control panel is less than 11 4 V The control panel battery does not pass the Dynamic test Call the Installer The control panel battery is disconnected or absent Call the Installer The control panel is not capable to recharge the battery Call the Installer The Mains power of the Control panel has failed Call the Installer Switching power supply does not work Call the Installer The output voltage of control panel is low Call the Installer The battery voltage of the Power Station x is less than 10 9 V Call the Installer The battery of Power station x does not pass the Dynamic test or it is disconnected or the Fuse protects against Battery polarity inversion is broken Call the Installer Switching power supply of the Power station x does not work Call the Installer The Output voltage of the Switching power supply of the Power station x is outside the normal range min 10 2 V max
68. n is enabled B Arm A Mode This operation will Arm and Disarm the Partitions in ac cordance with the A Mode Arming configuration pro grammed by the Installer 1 Hold the Key near the sensitive field of the Reader the light indicators will light in turn at 2 second in tervals as shown in Figure 5 2 Remove the Key when the Red and Amber light in dicators are ON Figure 5c atthis point the system will Arm in A Mode use When the Reader s EN50131 option is DISABLED the Amber light indicator turns OFF when you re move the Key if the Key s Partitions does not match the Reader s Partitions For example if a Key is assigned to the Partition n 1 and a Reader is assigned to the Partitions n 1 and 2 the Amber light indicator turns ON when you hold the Key near the Reader when you remove the Key from the Reader only the Partitions n 1 arms in A Mode and the Amber light indicator turns OFF ABSOLUTA READER OPERATIONS 53 m Arm B Mode This operation will Arm and Disarm the Partitions in ac cordance with the B Mode Arming configuration pro grammed by the Installer 1 Hold the Key near the sensitive field of the Reader the light indicators will light in turn at 2 second in tervals as shown in Figure 5 2 Remove the Key when the Red and Green light in dicators are ON Figure 5d at this point the system will Arm in B Mode use When the Reader s EN50131 option is DISABLED t
69. nal siren is activated for about 3 seconds and Voice Messages and or Report ing Codes are sent to the Telephone Numbers as signed to the General System Alarm event ask your installer for more information The display will show the message lt lt An alarm test will be performed on the system Would you like to pro gt gt Press Yes to carry out the test or No to close the popup window without doing the test m Date and Time Settings This option allows you to change date and time on the Panel clock Press or to make the desired change then press Save to memorise the change Setting Answering W Enable this option to allow the installer Installer to access the telephone agenda for voice calls and export the user codes Auto Arming and user keys Press gt Privacy to enable disable installer programming of telephone numbers for voice calls and to export user PINs and Keys gt Answering to enable disable the Control Panel to answer phone calls gt Installer to enable disable installer access to the Control Panel gt Auto Arming to enable disable arming disarming Partitions at scheduled times gt GSM to enable disable communication via GSM gt IP to enable disable communication via IP Read the relevant section for more information B Privacy Setting Answerin Installer voice calls and export the user codes Auto Arming and user keys Enab
70. nd the keypad will automatically re turn to the stand by status see the PREMIUM keypad manual for further information B Brightness adjustment Itis possible to adjust the brightness of the keypad keys and the brightness of the backlighting of the display It is also possible to adjust the inactive and the active bright ness the inactive brightness is the brightness to which the keypad reverts after 10 seconds of inactivity To adjust the active brightness follow the procedure described below 1a To increase the brightness press and hold the A key until the desired level is obtained 1b To lower the brightness press and hold the B key until the desired level is obtained 2 Press the OFF key to adjust the inactive brightness 3a To increase the brightness press and hold down the A key until the desired brightness is reached 3b To reduce the brightness press and hold down the B key until the desired brightness is reached 4 Press the ON key to adjust the active brightness and re turn to step 1a or press the ENTER key to confirm the chosen levels or wait a few seconds for the keypad to re turn to the inactive state ABSOLUTA OPERATIONS FROM LCD KEYPAD 31 LEDs and signals Keypads The Keypad signals the system status by its LEDs dis play and internal buzzer B LEDs and signals Table 2 shows the meaning of the indicator LEDs on the Keypads During standby status the display top
71. ng lt PIN gt OFF A B C and D Arming lt PIN gt A B C or D ON 36 Notes on Arming from Keypads Silencing Alarm Devices Wrong PIN User PIN Menu Structure Accessing the User menu lt PIN gt ENTER Action Alarm Reset 1 7 Extra Time Request 1 2 Clear Call Queue 1 3 Teleservice Request 1 4 Alarm Signals Test 1 5 Outputs ON OFF 1 6 Arm Partition Disarm 1 7 Zone Test 1 8 Clear Fault Tamper 1 9 Program ON OFF Answering 2 1 Enable Installer Teleservice 2 2 Auto Arm 2 3 Date Time 2 4 PIN Programming 2 5 Telephone Numbers 2 6 Change My Pin 2 7 Enable Disable Key 2 9 View View LOG 3 1 Zone Status and Bypass 3 2 GSM Module Status 3 3 Display SMS 3 4 IP Module status 3 5 ABSOLUTA INFO 3 6 READER OPERATIONS The Reader The Digital Key The Reader s Light Indicators Key at Reader No Key at Reader Multiple Systems Key operations No Action Disarm Away Arm Arm A Mode Arm B Mode Disarm Patrol False Key The Wireless Ke Away Arming n Stay Arming Disarming 9 Other functions A Low Battery TELEPHONE OPERATIONS Remote Access via Dialler mode Remote Access via Answer mode Typing in your User PIN Entering Commands Cancel Command J On Hook Remote Talk Listen in J Zone Partitions status 2 Turn Reserved Outputs ON OFF 3 Panel Arming Disarming 24 Arm Disarm Single Partitions 23 Enable Disable Installer 2 Clear call
72. nicate the positive result of the re quired action B Alarms Reset 8 This command will allow to clear Partition and or Control panel Alarms and restore the system to standby depending on the Access level of the PIN used via Telephone A beep will communicate the positive result of the re quired action m Disable Current User 3 This command will allow you to Disable the entered User PIN gt abeep will communicate the positive result of the re quired action This security feature will allow you to protect your system against unauthorized access you Dis able a PIN via Telephone it cannot be used again until it is Re enabled via the User menu refer to PIN Programming ABSOLUTA TELEPHONE OPERATIONS 5 J I III PI TP TIPI P R S LLL 1511 Partitions 61718 9 1 KERA sss _ G _ m _ _ ss G Gss j j 1 a G i E G E E E E A Wu N Hu G E W E E Table 7 7 Events Controlled by SMS ABSOLUTA Expandable Hybrid Control Panel 58 operations described this chapter possible onl
73. nings Tam pers m cone 003 ep AT Faults LA Fone Bypasses Cy Clear All The display s left side shows the signals category Alarms Tampers Faults and Bypasses if a category has no signals in progress or memorised the relative key is not displayed the central part of the display shows a list of signals for the category selected on the left side 3 Press Alarms to view alarms 14 Expandable Hybrid Control Panel ABSOLUTA 4 Press Tampers to view tampering 2 0089 det 6 S i ie Tampers Warnings f Alamna Extemal Siren 001 Panel Cover Warnings Battery Absence AM Tampers Lu d Bypasses v ypasses zt Bypasses Warnings f Alarms Tampers Lx Faults x Clear All gt The icon indicates that a signal occurred in the past memory gt Press or amp to scroll signals gt Press Clear to cancel the category signals gt Press Clear All to cancel ALL the tampering and fault signals use The Clear and Clear All keys are ONLY accessi ble to the Master User pz The Clear key is not available for the bypassed zones see Info gt Zone status to clear re include the bypassed areas pz The Clear All key is NOT available if there are only bypassed zones Menu Bar Saturday March 9 2013 A o6 e i Gl b Sc
74. nored by the control panel use The can be enabled from an LCD keypad as described in the section OPERATING YOUR SYSTEM FROM KEYPAD gt Program gt PIN Pro gramming 2 5 GSM Module IMEI Request You can found out the IMEI by sending the following SMS to the GSM number of the Control Panel ABS IMEI lt PIN gt lt Text gt gt PIN a User PIN enabled to manage the control panel via SMS gt Text additional text that can be used to assign a de scription to the command message and is ignored by the Control Panel If the operation is successful the Control Panel will re spond with the following SMS ABS IMEI lt IMEI gt gt is the IMEI number of the GSM Module of the Control Panel ABSOLUTA SMS OPERATIONS 61 LABEL CAS wl cl M alol o o ojl o NI ol e x o N lt lt w lt lt lt LABEL LABEL Table 9 9 PIN list Expandable Hybrid Control Panel 62 list Table 9 shows the Label assigned to the User gt the NO column shows the Identifier number of the User PIN gt the LABEL column to be filled in by the Installer is for the PIN User s name ABSOLUTA App iPhone and Android App for managing the Control Panel from a smartphone For more information visit the BENT
75. nstaller Program 2 3 ON OFF AutoArm Program 2 4 Date Time Program 2 5 PIN Programming Program 2 6 Telephone Number Program 2 7 Change my PIN Program 2 9 Disable Key View 3 1 View LOG View 3 2 Zone Status and Bypass View 3 3 GSM Module Status View 3 4 Display SMS View 3 5 IP Module Status View 3 6 ABSOLUTA INFO D o lt D 42 ps Partition mask for the User is programmed by the Installer not by the Master User who can only en able disable a User not create a new one see pro cedure 2 5 Accessing the User menu lt gt ENTER Enter a valid User PIN then press ENTER to View if pres ent the Troubles or Zone alarms Tamper events Alarm memories press more time ENTER to access the User menu The User menu will allow Users to access ONLY the options they are enabled for PREMIUM LCD and CLASSIKA LCD Keypads see User PIN Menu Structure You can access the User Menu also with Armed Partitions Press 1 2 or 3 to select the section ACTION PRO GRAM and VIEW of the USER MENU Press A and B to scroll the options then press ENTER to select the displayed option Press ESC to return one level pz Several Users can access the menu at the same time from different keypads The User menu provides the following options in three sections ACTION PROGRAM and VIEW ACTION gt Alarm Re
76. ntrol Panel ABSOLUTA Zone Status Info i Partition Status Fone 00 Scenarios Stand by Bypassad Zone Event Buiter Stand by lt G c i 2 This option allows you to view Zone status and by pass include Zones The display s central part lists the Zones of Partitions common to the Keypad and PIN used to access them The Bypass Resume key is displayed for each zone if the Bypassable option is enabled for that zone and status as shown in the following table Test the zone CANNOT cause alarms but its tivities are memorised in the Events Log this can only be enabled disabled by the Installer and is to check correct zone operations without causing undesired alarms contact the installer Bypassed the zone CANNOT cause alarms and its activities are NOT memorised in the Events Log Inactive the zone has not shown any signs of activity for some time it might not operate regu larly or its detector could be masked contact the installer e Alarm the zone has detected an intruder Low Battery the wireless detector battery en rolled on the zone must be replaced as soon as possible contact the installer Fault detector connections with the zone are short or interrupted contact the installer Al Tamper the detector connected to the zone has been tampered with open detached from wall etc contact the installer Lost the wireless d
77. on status MAIN PAGE on LCD Keypads 1 Press Aor B to view the Arm Part option 2 Press ENTER to select the option 3 Enter the Identification number of the required Par tition 4 Press gt ON for Away Arming gt OFF for Disarming gt A for Stay Arming gt for Zero Delay Stay Arming The keypad quits from the User Menu Zone Test 1 8 This option will allow you to test the Zones 1 Press A or B to view the Zone test option 2 Press ENTER to select the option 3 Select the signal to activate in correspondence of the test of the Zones gt 1 in correspondence of the test of the Zone the key pad will emit a Beep gt 2 in correspondence of the test of the Zone the siren will emit an alarm signal The options 1 and 2 be selected at the same time 4 Press ENTER to confirm 5 Press C or D to select ALL the Zones relevant to a Partition Partz or the Zones individually Zonez Press A or B to select the required Partition Zone 6 Press ENTER to include in the test the selected Partition Zone then go back to step 5 to select an other Zone Partition or to next step to start the test 7T Press ON to active the test In this phase you can test the alarm and tamper on the selected Zones You can see the test result on the key pad ABSOLUTA OPERATIONS FROM LCD KEYPAD 41 m Clear Fault 1 9
78. phone numbers Table 1 ABSOLUTA Panel Series Features 6 Expandable Hybrid Control Panel ABSOLUTA 5 FROM TOUCH KEYPAD The M Touch keypad with its ample display enables graphic presentation of system information Then the display is touch sensitive so is easy and intuitive to interact with In standby the keypad can display information shown in Figure 2 and described below Information shown by the keypad in standby de pends on operations programmed by the installer option 50131 enabled or disabled ask your in Staller for more information 1 Status Bar This area can show the following mes sages with decreasing priority gt System in Alarm above a red bar in an alarm gt Auto arm in above an orange bar if the system is about to be armed by the time scheduler gt Labels of open zones above a grey bar of zones with the option Active on Keypads enabled ask the installer for more information 2 Signals Icon This area can show the following icons if the EN50131 option is disabled with decreas ing priority gt fixed in an alarm gt A fixed with tampering or fault gt blinking with an alarm memorised blinking with tampering fault memorised gt J fixed with zones bypassed 3 SMS not read E This icon is displayed when there are unread SMSs the number above the icon indicates the number of messages not read Read GSM IP Re c
79. r system via the Answering device facility p The Answering function must be Enabled refer to OPERATING YOUR SYSTEM FROM KEYPAD Program ON OFF Answering 2 1 otherwise you will be unable to access your sys tem via remote telephone DO NOT use a telephone with a redial button to Arm or Disarm your system as this may put your system security at risk The Control Panel will answer your call after the pro grammed number of rings then will play the Welcome message and asks you to enter your PIN to access to the remote control Typing in your User PIN You can type in your PIN while the message is playing or during the pauses between message announce ments regardless of the Telephone Access mode Dialler or Answer Mode To type in your PIN 1 Press J 2 Enter your PIN 3 Press 1 p fthe Vocal Guide is disabled when your system recognizes your PIN it will emit an audible feed back signal beep beep and will accept com mands If your system DOES NOT recognize your PIN it will emit an audible error signal boop p fthe Vocal Guide is enabled a series of messages explains the procedures for operating the system from a telephone The Vocal Guide must be en abled by the Installer ms Press to repeat the messages from the start fyou type 10 invalid PINs into the Control Panel a tamper is generated and access to the system via telephone is or
80. ren continued 64 Expandable Hybrid Control Panel ABSOLUTA BOSS APP DTMF Event Schedule Feedback sms Feedback ARM Feedback ARM Feedback ARM Feedback ARM JARMA Feedback 2 Squawk _ SMS Mess No Message Message Message Squawk Yes Message No Message Squawk Yes Message No Squawk Yes Message Yes Voice Mess F Yes Message Yes Voice Mess Message 2 Squawk _ Squawk Yes Message No_ 2 Squawk _ Message Message Message Message Message Squawk Yes Message No Message Squawk Yes Message No_ 2 Squawk _ Message Squawk Yes Message No Message Squawk Yes Message No_ 2 Squawk _ Message Squawk Yes Message No Message Squawk Yes Message No Message Squawk Yes Message No Message Squawk Yes Message No_ 2 Squawk _ Message Message Message Squawk Yes Message No 2 Squawk _ Message Squawk Yes Message No Message Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Voice Mess Vo
81. ress ESC to step back to the User menu 38 Expandable Hybrid Control Panel ABSOLUTA m Clear Call Queue 1 3 If your Installer has programmed your Control panel to send Alarm calls it will call the programmed telephone numbers each time an Alarm occurs In the event of a False Alarm this command will allow you to interrupt the ongoing call and clear the call queue ps Limited User PIN s can ONLY delete calls gener ated by Events from their Areas while Main User PIN s can ALSO delete events from the system if enabled to do so by the Installer Disarming with a Main User PIN automatically de letes the calls in the queue if enabled to do so by the installer 1 Press A or B to view the Clear call queue option 2 Press ENTER to select the option 3 Press ENTER to confirm 4 Press ESC to step back to the User menu B Teleservice Request 1 4 If your Installer has set up this facility this command will allow you to request on line assistance remotely main tenance that does not require components or wiring 1 Press Aor B to view the Teleser request option 2 Press ENTER to select the option 3 Press ENTER to confirm ABSOLUTA OPERATIONS FROM LCD KEYPAD 39 m Alarm Signals Test 1 5 This option will allow you to Test the proper working order of the Alarm signalling devices When you select this option the Panel Output n 1 gen erally connected to the ex
82. rise the PIN and press Confirm 5 The display shows the number keypad Please enter the new PIN x 1 3 4 6 7 8 9 0 6 Enter the desired press to confirm Please reenter the new PIN 1 2 3 7 insertion and press to confirm if PIN numbers entered match the new PIN is memorised and the keypad returns to step 1 otherwise it goes back to step 5 PIN Duplicated Ifthe existing PIN is entered at Step 6 the display shows the message PIN Duplicated 07 111213 UPE 11 81 0 This means that the PIN was first used by another user for security reasons the PIN is disabled and the user is prompted to enter another PIN The PIN can be re enabled by a Master User as de scribed above Keys Menu scenarios This option allows you to disable enable Keys and Wireless keys A Key Wireless key can only be disabled enabled by PINs enabled in Partitions where the Key Wire less key is enabled 1 Press Keys to disable enable the Keys or Key Fobs to disable enable the Wireless keys the dis play s left side shows the list of Keys Wireless keys available with their labels and status in groups of three ps Available Keys Wireless keys and labels are set by the installer 2 Press Or to scroll the list of Keys Wireless keys then press the green rectangle Enabled to disable the Key Wireless key or the gray rectangle Disabled to enable t
83. rmed to enable it when the partitions of the keypad are disarmed If you select ON or ON if Disarmed the lower part of the display shows images present in the SD card in groups of three 2 Press or gt to see the other images touch an image to select deselect it images selected are in a green frame ps Default all images are selected 3 Select the Slide Show tab to set how long you re main on each image Menu Setting Backlight Scenarios Buzzer Control Into Static images Clock Mode Clean Mode Speed Background Image Language Scrolling Text Exit Valid Values 2 5 10 20 30 45 seconds and 1 minute Default 2 seconds B Clock Mode e OA orem 105 Setting lt Menu Backlight QOEM Clock Mode D Scenarios Please select the mode Buzzer Control Picture Frama info 12 Hour Clock Clean Mode tigi Background Image GSM IP Language Scrolling Text Exit 0 a E Select how time should be displayed gt 12 Hour Clock will use numbers from 00 to 12 to display time with the initials AM for the morning and PM for the afternoon gt 24 Hour Clock default will use numbers from 00 to 11 for morning times and 12 to 23 for the afternoon ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 23 m Clean Mode Menu Setting Clean Mode Backlight See Clean Mode Scenarios Bu
84. rming Partitions for more information ir 05 Thursday Apm 17 2014 42220 900 4363 A Figure 2 The M Touch keypad is on stanqby EN50131 disabled ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 7 11 Home Key Press this key for less than 3 seconds to display the Login Screen read Entering the Home Screen for more information Keep this key pressed for at least 3 seconds but less than 10 seconds to enter calibrate screen read Screen calibration for more information Keep this key pressed for at least 10 seconds to re store the keypad os This key blinks when the control panel receives an SMS read Received SMS for more information 12 Signals LED amber If option EN50131 is dis abled it comes on with a signal read Viewing Signals for more information 13 Power LED green When on the keypad is pow ered Emergency Keys Emergency Keys enable the user to recall actions pro grammed by the installer quickly with no need to enter a PIN To enter Emergency Keys gt touch any point on the screen when the screen is off or shows Digital Frame images then touch any point on the screen again or gt press the Home key for at least 3 seconds Enter PIN ym il 2 3 2 4 5 6 N Panic 7 8 9 US Emergency The keypad displays the Login Screen with the Emer gency Keys described below Fire Keep q pd pressed unt
85. s FastBlink No 2Squawk No Henne Display Mess LEDON Yes Squawk Yes FastBlink No 2Squawk No Display Mess Mess DispayMess LEDON Yes Squawk Yes Display Mess put Mess Display Mess Mess Display Mess Display Mess gum Mess Display Mess Mess Display Mess No Fast Blink No 2Squawk No Display Mess F LEDON Yes Squawk Yes Fast Blink 2 Squawk No Display Mess LEDON Yes Squawk Yes Display Mess F FastBlink No 2 Squawk No Display Mess F LEDON Yes Squawk Yes_ FastBlink No 2 Squawk No E DispayMess LEDON Yes Squawk Yes FastBlink No 2Squawk No pene Emus Mess E Display Mess LEDON Yes Squawk Yes FastBlink No 2Squawk No Display Mess Mess DispayMess LEDON Yes Squawk Yes Display Mess Display Mess Display Mess Display Mess Display Mess Display Mess Display Mess No Fast Blink 2Squawk No _ Fast Blink 2Squawk No F Fast Blink 2Squawk No _ F LEDON Yes Squawk Yes F FastBlink 2Squawk No F LEDON Yes Squawk Yes FastBlink No 2Squawk No bona yes vee Table 10 Arming Block Conditions F Force arming Cont Boop Continuous Boop 1 You can force the arming when the Active Zone is Hold up Zone Squawk sound emitted from an external si
86. set gt Extra Time request gt Clear call queue gt Teleservice request gt Alarm signals test gt Outputs ON OFF gt Arm Part gt Zone Test gt Clear Fault Tamp PROGRAM gt ON OFF Answering gt ON OFF Installer gt ON OFF Auto arm gt Date Time gt PIN programming gt Telephone number gt Change my PIN gt Disable key O VIEW gt View LOG gt Zone status and Bypasses gt GSM Module Status gt Display SMS gt IP Module Status gt ABSOLUTA INFO At default only the User PIN nr 1 is Available and Active and it is 0001 The operations regarding the Partitions and the Zones will have effect ONLY on the Partitions and Zone s Partitions assigned both to the used Key pad and PIN Press ESC to step back to the User menu or wait for 3 minutes ABSOLUTA OPERATIONS FROM LCD KEYPAD of Action m Alarm Reset 1 1 This option will allow you to restore all Alarm signalling devices to Standby and delete the Zone and Partition Alarm memories use The Control Panel be programmed by the in staller to Reset the Alarm Memory automatically when armed use Alarm Memories can only be Reset automatically with a Master User PIN on arming 1 Press A or B to view the ALARM Reset option The number 1 1 on the display indicates the sec tion ACTION and ALARM Reset is the No 1 op tion and so on
87. t gt This command will Arm all the common Partitions of the User PIN and the Keypad concerned If a Exit Delay is sett the keypad will signalize it on the display and the buzzer will emit a series of beep B Disarming lt gt OFF This command will Disarm all the common Partitions of the User PIN and the Keypad concerned Disarm under Duress PIN with Duress option en abled This command requires entry of a Duress PIN The Control panel will Disarm the Partitions and will send the programmed Alarm calls but will not signal the outgoing calls on the Keypad usually signalled by a over the 2 icon ms DURESS PINs are for forced disarming disarming under threat The Duress PIN will disarm the sys tem and activate the Digital Communicator that will call the Central Station and dialler that will send recorded voice messages to the programmed telephone numbers Disarm by Patrol PIN If a Patrol PIN with Patrol option enabled is used to Disarm the Partitions the Control panel will rearm the Partitions automatically when the programmed Patrol Time expires PATROL PINs are enabled for Global arming dis arming PATROL PINs can disarm partitions tem porarily Partitions disarmed by a PATROL PIN will be rearmed automatically when the programmed Patrol time elapses Multi PIN Key Disarming If the installer has pro grammed the multi PIN Key disarming for a Partition you need to
88. tatus of Partitions and the Arming Key ALL Partitions DISARMED and an Arming Mode se lected Global in the following example Arm Global th Disarmed gt Partitions ARMED is a Mode Global in the following example and SAME Arming Mode selected Armed Disarm Global gt Partitions ARMED in a Mode STAY Type A in the following example and DIFFERENT Arming Mode selected Global in the following example B Arming Select the desired Arming Mode then press the Arming Key access the system 000 1 24 4 5 6 7 9 If there Arming Block Conditions see relative paragraph the keypad starts to scan Exit Delay if pro grammed Exit Delay is also signalled audibly increasing in frequency when arming is in less than 10 seconds Leave the protected zones along the preset route be fore Exit Delay expires or disarm the Partitions At the end of Exit Delay if programmed the keypad displays the Standby Screen B Disarming If you violate a Delayed Zone the keypad starts scan ning Entry Delay Enter PIN to disarm E 1 2 3 4 5 6 7 8 9 24 In that case just enter a valid PIN and press V to dis arm the Partitions before Entry Delay expires In all other cases enter the Home Screen as described in Entering the Home Screen and press Disarm use Entry Delay is also signalled audibly increasing frequency when
89. ternal siren is activated for 3 seconds and the Voice Messages and or the Reporting Codes are sent to the Telephone Numbers assigned to the General System Alarm event ask to your installer for more information 1 Press to view the Alarm sign test option 2 Press ENTER to select the option 3 Press ENTER to perform the Test 4 Press ESC to step back to the User menu B Outputs ON OFF 1 6 This option will allow you to silence the Alarm Outputs Sirens and turn the appliances sprinklers lights etc ON OFF 1 Press AorB to view the OutputOFF STOP option 2 Press ENTER to turn the appliances ON OFF and go to Turn the appliances ON OFF gt press OFF to silence the Alarm Outputs gt press ON to resume the silenced Alarm Outputs 3 Press ENTER to confirm and go back to step 1 Turn the appliances ON OFF 3b Enter the Identification Number of the required Out put 4b Press ENTER the Keypad will emit a Boop if the selected Output is NOT Reserved for appliance control else shows 5b Press gt ON to activate the Output gt OFF to deactivate the Output 6b Press ESC to go back to step 3b 40 Expandable Hybrid Control Panel ABSOLUTA m Arm Partition Disarm 1 7 This option will allow you to Arm or Disarm the Parti tions one by one The single partition can be directly armed from Par tition status refer to View Partiti
90. than press ENTER and go back to step 3 Automatic PIN The Panel generates a random PIN for you The Automatic PIN does not allow Users to have the same PINs 6b Press ENTER to go back to step 3 44 Expandable Hybrid Control Panel ABSOLUTA Duplicated If the existing is entered at step the display shows the message Duplicated PIN This means that the PIN was first used by another user for security reasons the PIN is disabled and the user is prompted to enter another PIN Press ESC The PIN can be re enabled by a Primary User as de scribed above B Telephone Numbers 2 6 This option will allow you to change delete the Tele phone numbers 1 Press Aor B to view the Telephone Num option 2 Press ENTER to select the option 3 Enter the Identification number of the required Phone number then press ENTER gt f you choose Digital Dialler Phone Number the display shows the following message You can set ONLY the Voice Dialler Phone Num bers then press ESC and go back to step 3 f you choose a Voice Dialler Phone Number the display shows the current number or an empty field the first digit will blink to indicate that it is ready for programming Enter the required Phone number Use keys 0 through 9 to enter the Phone number Press A to enter a long 4 seconds pause indicated v v gt D 4 D n N F 5
91. tion Tamper events which occur when the system is dis armed can be silenced via the Reset Alarm and Out put ON OFF option from the User Menu access allowed to Master and User PINs For further information refer to Using Digital Keys Cards Wrong PIN If a wrong PIN is entered on a LCD keypad the display will show an error message After a few seconds the keypad come back in the standby status and the right PIN can be entered again After 10 wrong entries the LCD keypad will lock for 90 seconds 36 Expandable Hybrid Control Panel ABSOLUTA User PIN Menu Structure There are three types of User PINs Menus depending of possibility to manage the system commands by LCD keypad The types of PINs Menus are 1 Master User PIN Menu 2 Normal User PIN Menu 3 Limited User PIN Menu Inside of the 127 available User PINs the Installer pro grams which and how many PINs will be Master Nor mal and Limited User PINs The Master User the Normal User and the Limited User can manage the options of User menu as per the following table OPTIONS Master User Normal User Limited User Action 1 1 Alarm Reset Action 1 2 Extratime request Action 1 3 Clear Call queue Action 1 4 Teleservice request Action 1 5 Alarm Signal test Action 1 6 Output ON OFF Action 1 7 Arming Action 1 8 Zone Test Action 1 9 Clear Fault Tamper Program 2 1 ON OFF Answering Program 2 2 ON OFF I
92. tition Identifier entered is 0 After the message the system will go back to step 1 Zone status Press in sequence 212121 2110 know the current status of the Zone The Zone status will be indicated by the following messages lt lt Active zone gt gt Messagge194 if the zone is active lt lt Tampered zone gt gt Message 195 if the zone is Tampered lt lt Zone in fault gt gt Message 196 if the zone is fault lt lt Zone alarm gt gt Message 197 if the zone in alarm lt lt Standby zone gt gt Message 198 ifthe zone is in standby boop if zone Identifier entered is 0 After the message the system will go back to step 1 B Turn Reserved Outputs ON OFF 3 This command will allow you to turn ON OFF the ances Sprinkler system Courtesy lights etc con nected to the Reserved Outputs The Output Identifier number must always be with 2 digits long if necessary enter the required 0 to fit 1 Press 31 to access Output control 2 Enter the Identifier number of the required Output 3 Press Jtoturn or J to turn OFF the appliance connected to the selected Output An audible signal will communicate the result of the command Beep if action done Boop if action fails The appliance will turn ON OFF immediately and the system will go back to step 1 56 Expandable Hybrid Control Panel ABSOLUTA B Panel Arming Disarming 4 This command will allo
93. tus Press Enable to enable the option or Disable to disable it B GSM Menu Setting Privacy Answering Installer info Auto Arming This option will allow you to enable disable the GSM Press Enable to enable the option of Disable to disable it m IP Setting Privacy Wc Scena amp ros Answering info Installer Auto Arming zu GSM g ii GSM IP This option will allow you to enable disable the IP com munication Press Enable to enable the option or Disable to disable it ABSOLUTA OPERATIONS FROM TOUCH KEYPAD 21 Setting Backlight Se I H Buzzer Control Picture Frame screen Off After ig ara Screen Brightness GSM IP Press gt Backlight to set screen inactivity turn off times and backlighting intensity gt Buzzer control to set keypad buzzer volume gt Picture Frame to select the photo or photos the keypad must display during standby gt Clock Mode to set how the time is displayed gt Clean Mode to clean the keypad screen gt Background Image to select the 5 back ground image gt Language to select the keypad language gt Scrolling Text to disable the scrolling text Read the relevant section for more information The Keypad Menu can only be entered with a Mas ter User PIN Backlight Menu Setting Backlight Backlight Scenarios B
94. uzzer Control Screen Off After Picture Frame into Screen Brightness GSM IP Exit Screen Off after Set screen turn off inactivity time Valid Values 10 20 30 seconds and 1 2 5 10 min utes Default 1 minute Screen Brightness Set screen brightness Valid Values Extra low Very low Low Normal High Very high Extra high Default Very high Buzzer Control Setting Backlight Scenarios Picture Frame Into X GSM IP Adjust Buzzer volume Valid Values Buzzer off Very quiet Quiet Normal Loud Very loud Extra loud Default Very loud 22 Expandable Hybrid Control Panel ABSOLUTA m Picture Frame Menu Setting Backlight Scenarios Buzzer Control info Clock Mode Clean Mode qA Background Image GSM IP Language Scrolling Text aa Exit This option allows you to use the keypad as a digital frame gt the images to be displayed must be memorised in the main folder of an SD Secure Digital card gt the SD card must be maximum 32 GB and be format ted 16 or 32 gt images must be in JPG or TIF format maximum 1 MB gt for the best results we advise using 800x480 pixel images gt the SD card must be inserted in the specific keypad slot The images of the Digital Photo Frame are displayed when the keypad is in standby 1 Press gt OFF to disable the Digital Frame gt ON to enable it always gt ON if Disa
95. w 1 Press Aor B to view the Zone Status option 2 Press ENTER to select the option 3 Select the required zone by entering its Identifica tion number or scrolling by pressing A and B the display bottom line shows the label of the selected zone 4 Press ENTER the display bottom line shows the zone status as follow ST BY the zone is in standby ACTIVE the zone is active gt OPEN the zone is open tampered SHORT the zone is short circuited WORKING the zone is operative included BY PASS the zone is bypassed 5 Press OFF to bypass the zone ON to include the zone 6 Press ESC to go back to step 3 ABSOLUTA OPERATIONS FROM LCD KEYPAD 47 m GSM Module Status 3 3 This option allows you to view the GSM Module s sta tus 1 Press A or B to view GSM Status 2 Press ENTER to select the option The display shows the GSM Module s status on the top line on the left the GSM signal s strength on the right and the name of the GSM operator on the bottom line as described below GSM OK the GSM Module is working normally LinkLOST Network problem no SIM FAULT GSM module problem Wrong FW firmware not compatible with Control Panel no asterisks mean no GSM signal three asterisks 3 Ifthe GSM Modules status is OK press ENTER to view the telephone number of the SIM card placed in the GSM Module th
96. w you to Arm Disarm the Panel in accordance with programming 1 Press to access Arming Disarming 2 Press gt LJ to know the current status of the Partition Panel gt to Arm the Panel gt 2 to Disarm the Panel gt either 31 14 5 or 8 to Arm the Panel respectively in A B C or D Mode Will be armed disarmed ONLY the PIN s Partitions The Control Panel status will be indicated by the follow ing messages Panel armed Messages 199 200 if the Panel is armed Panel disarmed Messages 199 203 if the panel is Disarmed lt lt Not ready action will not be executed gt gt Mes sage 204 if there is any problem that inhibits the Panel arming Not ready press one to arm anyway gt gt Message 205 if there is any problem that inhibits the Panel arm ing but it is possible to arm anyway In the last case if is pressed anyway to arm the messages Panel gt gt will follow Message 199 200 The Partitions will Arm Disarm immediately and the system will go back to step 1 B Arm Disarm Single Partitions 5 This command will allow you to Arm Disarm the tions individually ps The Partition Identifier number must always be 2 digits long if necessary enter the required 0 to fit 1 Press to access Arm Disarm Single Partitions 2 Enter the Identifier number of the Partition 3 Press J to Arm the Partition
97. y if the installer has installed the GSM Module in your control panel and has carried out the respective pro gramming ask your installer which operations are pos sible with your control panel Some of the operations described this chapter require you to send your PIN by SMS To increase the security of your system once the operation re quested has been completed you can disable your PIN as described in the respective paragraph so that no one else can use it without your knowledge Events Controlled by Caller ID You can activate some events See Table 8 simply by calling the control panel s GSM number at no cost When the control panel receives a call from one of the Phone Numbers listed in Table 8 it waits for a few rings then it hangs up and activates the respective Event the control panel then confirms with one ring to the phone number if enabled to do so by the installer ps The ring for confirmation may be delayed if there are other calls in the queue or it may be lost if the queue is full or because of problems with the GSM network Phone Numbers 1 2 3 4 5 6 T 8 Table 8 Events Controlled by Caller ID SMS OPERATIONS Events Controlled by SMS You can activate and deactivate events Table 7 by sending the following SMS to the control panel s GSM number ABS E lt PIN gt lt ON OFF gt lt Command String gt lt
98. ybrid Control Panel ABSOLUTA TELEPHONE OPERATIONS If your Installer has enabled the User PINs you will be able to control your system via any touch phone For recording the customized voice messages your system has a AS100 Stand alone Audio station Each PIN can be programmed to control specific func tions and Partitions PIN 1 CANNOT access the system by tele phone You can access the system over the phone gt by receiving a call from the Control panel Dialler mode gt by calling the Control panel when the Answering de vice facility is enabled Answer mode Remote Access via Dialler mode If your installer has duly set up your Control panel the Dialler will send voice messages to the programmed telephone numbers when Alarm Tamper Fault condi tions are detected If you receive a Dialler call you will be able to access your system during the call by enter ing your PIN on the telephone keypad You can enter your PIN while the message is playing or during the pauses between message announcements fthe Confirm successful calls option is Enabled you must press the Star key while the voice message is still running otherwise the Control panel will consider the call Unsuccessful and will carry out the programmed Actions Remote Access via Answer mode If your installer has set up your Control panel to answer incoming calls you will be able to access you
99. zzer Control Picture Frame Select below to begin clean mode Info Clock Mode Bark GSM IP Background Image d PER EE Language Scrolling Text J _ I Exit This option displays a black screen and makes the touchscreen insensitive to the touch in this way it is easy to identify dust and remove it with a cloth without any command being activated by mistake AN The screen must only be cleaned using a clean cloth DO NOT use any kind of detergent or sol vent 1 Press Clean Mode to block the touchscreen Clean Mode in Progress 2 Press the Home key to quit Cleaning Mode the keypad returns to the Home Screen us However Clean Mode ends after 30 seconds B Background Image m am C C o o g mc o Setting lt Background Image Menu L 2 Backlight renarins Background Image Buzzer Control Picture Frame Clock Mode Clean Mode into Language Scrolling Text b Exit The Background Image is the one displayed on the back of each keypad screen The Background Image can be chosen from amongst those in the keypad memory and from amongst those in the SD card inserted in the keypad read Picture Frame for more information The display shows images present in the keypad mem ory and those in the SD card inserted in the keypad in groups of 6 Press or to see the other images touch

operations from touch keypad

Contents

Download Pdf Manuals

Related Search

Related Contents