TRAILER USER`S MANUAL
Contents
1. eet th A Trailer Serial No NUGENT TRAILERS 15 Aughnagar Road Galbally Dungannon Co Tyrone BT70 2PP N Ireland T 44 0 28 8775 8583 Office T 44 0 28 8775 9910 Spare Parts F 44 0 28 8775 8956 E info nugenttrailers com W www nugenttrailers com TRAILER USER S MANUAL Congratulations on the purchase of your Nugent Trailer With full type approval ECWVTA Nugent Trailers are designed to give many years of reliable service The instructions contained within this handbook are provided to enable the user to achieve the best possible service from the trailer and to ensure that the trailer is used safely Nugent Trailers strongly advise that this handbook is read and clearly understood before the trailer is put into service If you are unsure of the meaning or if any procedure is unclear or you require any further information please feel free to contact your local Dealer or Nugent Trailers directly The following points are important to adhere for safe towing of any trailer e t is important that the vehicle used to pull the trailer is adequate for the purpose e That the engine is large enough to tow the trailer and load e That the brakes are powerful enough to stop the vehicle and trailer safely e The Gross Trailer Weight does not exceed the Towing Capacity of the towing vehicle Make sure the ball hitch towing bracket on the towing vehicle is of an approved type Never exceed the maximum gr2. severely damaged for a repair to be carried out the tyre must be replaced GENERAL MAINTENANCE This should be carried out as per the maintenance schedule detailed in Appendix 2 Wheel hubs Repack with grease after bearing change Damaged or missing hubcaps should be replaced as soon as possible Leaf springs spring hangers no lubrication is necessary Check the tightness of the self locking nuts on the U bolts every 2 500 miles Brake linkage All moving parts should be greased or oiled every 2 500 miles Manufactured with Pride Page 13 OPERATING SAFETY INSTRUCTIONS COUPLING AND JOCKEY WHEEL The general condition of the overrun coupling unit and jockey wheel should be checked every 2 500 miles Check for damaged or worn parts and these should be replaced immediately Lubricate the wheel spindle and screw thread every 5 000 miles To reduce the wear on your towing ball and coupling head clean out the cup in the coupling head monthly and apply new grease Follow these next few points every 2 500 miles Coupling mounting bolts check for tightness Coupling head bolts check for tightness Coupling head using a 50mm test towball to meet BSAU 113c it must be between 49 61mm and 50 00mm check that it locates and locks correctly in the coupling head and that any wear location indicators are functioning see below Lubricate the mechanism and lightly grease the inside of the coupling socket Draw tube check by mov
3. However if the lug is now riding noticably higher up the slot the original 50mm ball should be replaced NB If it is necessary to replace the coupling head remember to carry out the first check once more as the 50mm ball may need replacing as well GALVANIZED FINISH Hot dip galvanizing is the process of coating steel with a thin zinc layer by passing the steel through a molten bath of zinc at a temperature of around 460 C All Nugent trailers are galvanized to prevent rust and extend the trailers working life Galvanizing creates a protective outer layer that protects the steel from wear and rust As part of the natural ageing process galvanized surfaces form an outer layer of oxide which protects the reactive outer layer of zinc and underlying steel from further corrosion The appearance of the trailer will be between bright silver to a dull grey If the trailer is exposed to road salt this can alter the appearance of recently galvanised surfaces to grey or black with white or grey deposits This does not affect the protective properties of the finish but it would be good practice for the user to wash the trailer regularly especially during the winter months Manufactured with Pride Page 15 OPERATING SAFETY INSTRUCTIONS SECURITY Each trailer is security marked The serial number will be stamped onto the identification plate on the drawbar as well as stamped onto the chassis leg or drawbar but as an added means of supporting
4. the breakaway cable if it is anyway frayed or kinked replace before using the trailer Check the ball is clean and the coupling head cup is well greased Make sure the trailer handbrake is fully applied Make sure that the jockey wheel clamp handle is tight and by turning the jockey wheel jack handle raise the coupling so that it is higher than the coupling ball Now reverse the vehicle up to the trailer so that the coupling head is directly above the towing ball Grasp the locking handle on top of the coupling and pull the trigger backwards with your thumb Then lift the handle until the automatic coupling mechanism engages and holds the locking handle in the open position The handle trigger can now be released Lower the coupling head onto the coupling ball by means of the jockey wheel jack handle until the coupling head automatically engages with the towing ball Make sure the hitch is attached securely by trying to lift the coupling off the ball with the jockey wheel Withdraw the jockey wheel taking care that the wheel is wound up fully and positioned well clear of the brake linkage as follows e Before releasing the clamp make sure the jockey wheel is wound up to Its full height e Release the clamp e Lift jockey wheel stem and tighten the clamp with the wheel facing the front and in contact with the inside of the drawbar channel Check the condition of the breakaway cable and attach to the towing vehicle ensuring the cable is f
5. use c Any goods the identification marks of which have been altered or removed d Any goods which have not received the basic normal maintenance such as tightening or proper adjustment of fittings and normal lubrication e Any goods which have been altered or repaired other than on instruction or with having written approval by the Sellers f Any second hand goods or part thereof Any allegedly defective part or parts returned to the Sellers must be sent carriage paid No claim for repair or replacement will be entertained unless upon discovery of the alleged defect written notification is sent to the Sellers giving at the same time the name of the Buyer from whom the goods were purchased and the date of purchase together with full details of the alleged defect and the circumstances involved also the serial number of the trailer etc The Sellers shall be under no liability to their Buyers and first and subsequent users of their goods or to any other persons for loss or damages howsoever arising out of or in any way connected with or arising from the manufacture sale handling repair maintenance replacement or use of its goods or the failure of malfunction of any of its goods Representation and or warranties made by any person including Buyers and employees and other representatives of the Sellers which are inconsistent or conflicting with these conditions are not bonding upon the Sellers unless given in writing and signed by a Di
6. ANSPORTING LIVESTOCK The following points should be followed when transporting livestock Plan the journey beforehand avoiding unnecessary delays Check each animal for fitness to travel before loading Load transport and unload animals calmly and without rushing Do not over stock the trailer Full use should be made of partitions to prevent animals being thrown about by the motion of the vehicle and for the safe towing of the trailer This is one of the provisions of the Transit of Animals Road amp Rail Order 1975 S I No 1024 for the protection of animals during transit and permits the following maximum pen lengths Sheep pigs goats 3 1m 10 2 Calves 2 5m 8 2 Cattle 3 7m 12 1 Animals should be allowed sufficient floor soace and adequate fresh air circulation Drive carefully with consideration for the animals avoiding sharp braking accelerating and cornering lf necessary stop and check the animals during the journey Do not load incompatible animals in the same pen for example horned and un horned cattle Do not leave the animals unattended in the trailer for long periods of time SERVICE AND MAINTENANCE PRECAUTIONS The correct assembly and adjustment of all equipment is critical to the safe operation of the trailer Therefore the procedures must only be carried out by competent and trained personnel It is advisable to wear suitable protective equipment such as safety glasses gloves and f
7. ace mask All procedures should be carried out with the trailer on level ground with either the parking brake applied or wheel chocks front and rear In addition the drawbar should be supported with the trailer horizontal Manufactured with Pride Page 6 TRAILER USER S MANUAL a eee HUB BEARINGS Place the trailer on stands with all wheels free NOTE The handbrake lever should be secured in the off position 1 0 Rock the road wheel to see if there is play in the bearing see point 6 2 0 Remove the wheels and hub cap Slacken the brake adjuster bolt if needed 3 0 Remove the axle nut this may be a castellated nut retained with a split pin or alternatively it may be a high torque nut 4 0 Remove the brake drum hub pullers may be required taking care not to displace the bearings WARNING Avoid inhaling brake dust Do not use a compressed air line to clean the drum 5 0 Carefully remove the dust using a small brush 6 0 Check the condition of the brake drum replace the drum if deep score marks are visible Unitised bearings used on Nugent LS126 and LS146 livestock and GP64 trailer hubs are a Single non adjustable assembly with integral seals If the check at point 1 above indicated excess play in the bearing then the bearing unit should be pressed drifted out having removed the retaining circlios and replaced as follows 6 1 The new bearing should be pressed gently drifted into place ensuring that it remains
8. e 3 Secure the cable to a suitable point on the tow vehicle refer to the vehicle or tow bar manufacturers specifications for the location 4 Ensure that the cable is not pulled tight during articulation of the trailer and remains clear of the ground FITTING WHEELS Ensure wheel stud threads and wheel seating surfaces are clean and dry Place wheel over locating rim on the hub Slightly tighten each nut initially and then fully tighten following the sequence shown Q w SGS L 5 F Manufactured with Pride Page 12 TRAILER USER S MANUAL WHEEL BOLTS SHOULD BE CHECKED AFTER FIRST 25 MILES 40km OF SERVICE AND BEFORE EACH SUBSEQUENT JOURNEY TYRES Thread The same laws apply to trailers as apply to vehicles so ensure that there is sufficient tread to last until the next service i e Minimum 1 6 mm for the centre three quarters of the tread for the whole circumference Check for any cuts bulges or any other damage Care should be taken i e Wear gloves in case any screw heads pieces of glass or tyre steel ply wires are protruding from the tyre carcass Check for any uneven tyre wear that might indicate damage to the suspension incorrect tyre pressures or wheels being incorrectly balanced Check tyre pressures Punctures have to be inspected and repaired by a specialist tyre distributor Do not fit tubes to tubeless tyres as this can lead to a blow out in the event of a further puncture If the tyre is too
9. e EVERY 16000KM 10000 MILES WEEKLY OR 1 YEAR MAINTENANCE FIRST 2000KM EVERY 4000KM PROCEDURE 1200 MILES 2500 MILES O wm omean a E ee M E ee OOOO C manare non OOO ee tomes mes ome a E a a a a a a a a Check Spring U Bolt Nut Tightness ELECTRICAL Check 7 Pin Plug Check Lights Check Cable Connections Check Reflectors GENERAL Lubricate Crib Hinges Check lubricate taildoors ramps gates cribs Check Floor Sheeting Manufactured with Pride Page 18 THE NUGENT GUARANTEE Subject to hereunder provided the Sellers undertake to correct either by repair or at their election by replacement any defect of material or workmanship which in any of its goods within twelve months after delivery of such goods to a first user with the exception of contractors or commercial users when warranty period is six months The term goods when used in this document means the article or articles described in invoice as sold by the Sellers but does not include equipment or proprietary parts or accessories not manufactured by the Sellers The Sellers however undertake to pass on so far as they legally can to the first user the benefit of any warranty given to the Sellers by the suppliers of such equipment parts or accessories The understanding shall not apply to a Any goods which have not been sold by the first user b Any goods which have been damaged by unfair wear and tear neglect and improper
10. ent is carried out including hub adjustment 4 Follow the brake adjustment procedure starting at item 2 BREAKAWAY CABLE Removal It is important to ensure that the handbrake lever is prevented from operating The handbrake should be released and the handbrake lever should be secured in the off position to prevent the handbrake lever operating Remove the existing cable from any guides taking note of the route Where a coll fitting is used on the handbrake use pliers and screwdriver to prise the coils of the retention ring apart and remove the ring from the handbrake lever Where a clevis and pin fitting is used on the handbrake remove the split pin and withdraw the clevis pin Manufactured with Pride Page 11 OPERATING SAFETY INSTRUCTIONS Refitting WARNING Always use the correct Tyoe Approved replacement from the manufacturer as an incompatible cable will fail to operate the handbrake mechanism correctly For the coil fitting use pliers and screwdriver to prise the coils apart and fit the ring to the handbrake lever Check that the cable is free to move on the ring For the clevis fitting insert the clevis pin and retain it with the split pin provided In all cases thread the cable through the guides Operation 1 Ensure that the cable passes through any guides provided This is important to ensure that the cable operates under the widest range of circumstances 2 Check that there is no damage or fraying prior to us
11. ing the shaft up and down that the bearings that support the draw tube are not worn Drawtube gaiter check for splits and tears Replace if damaged Damper with the handbrake off and wheels chocked push the coupling in If it does not move or goes in with no resistance and does not push itself backout it must be worn and should be replaced It should move in steadily with uniform resistance N B it is essential that the correct specification of replacement damper is used Handbrake check the action for correct movement Lubricate the pivots Grease nipples apply a grease gun to nipples on top of the housing ensuring that a liberal amount of grease is applied Breakaway cable check for kinks fraying operation of the clip and that the cable securely attached to the burst ring Checking the coupling head for excessive wear To check if either the vehicle s tow ball or ball coupling is excessively worn follow the following procedure Once coupled together if the square lug 1 at the rear of the head handle 2 is resting on the bottom of the slot in the trigger 3 either the coupling head or the tow ball or both are worn Manufactured with Pride Page 14 TRAILER USER S MANUAL HEAD HANDLE cE TRIGGER iJi GOF ALLOWANCE FOR BALL WEAR Irni If so check further by using a new 50mm ball If the lug remains at the bottom of the slot the coupling head is excessively worn and should be replaced
12. lity caused by loading too heavily on one side or the other Dangerous loss of stability when loads are loose and move around Danger of loads parting from the trailer Load shooting forward when the outfit brakes This is particularly acute if the load consists of planks bars etc laid in line front to back There is a very significant danger of light items being lifted out of a trailer by the slipstream All items should be secured Loading practice should therefore take into account e Secure restraint e Recommended nose weight e Weight distribution and balance LOADING SKIDS RAMPS Great care should be exercised when using loading skids ramps When unloading or loading make sure it is carried out on level ground Have somebody on hand for assistance Make sure that the skids ramps are positioned correctly with the lower ends on firm level ground parallel with the trailer and in line with the centre of the tyres of the vehicle to be loaded unloaded and that the skid top angles are in contact with the trailer rear cross member over their full width See Fig 8 The assistant should stay well back during loading unloading Take sufficient time and continuously check that the vehicle is correctly positioned For loading vehicles under their own power the ladder type skids ramps are more suitable whereas winching will normally be easier with the flat type Manufactured with Pride Page 5 OPERATING SAFETY INSTRUCTIONS TR
13. ng to the brake drum surface TRAILER LOADING Loads must be securely tied down or restrained There must be no load projections outside the trailer that might cause danger to other road users Wherever possible loads should be evenly distributed across the trailer and positioned in such a way as to keep the nose weight within the recommended limits Refer to the manufacturer s recommendation and or the nose weight limit of your vehicle If uneven loads have to be carried ensure that individual wheels axles are not overloaded To achieve this it may be necessary to reduce the overall load NOTE Good towing practice should always take into account the inevitable effects on vehicle handling braking and general stability of towing a trailer behind the vehicle Check weight distribution The most significant risks associated with poor loading weight distribution are Loss of steering control caused by loading behind the centre of gravity this is very likely to cause snaking Loss of overall control and potential damage to the towing vehicle caused by excessive loading in front of the centre of gravity This causes vehicle steering to be less effective giving under steer and with front wheel drive vehicles causing loss of traction Excessive nose weight is likely to place unacceptable stresses on the tow bar and on its mounting points on the vehicle Manufactured with Pride Page 4 TRAILER USER S MANUAL Loss of stabi
14. oss weight shown on the trailer plate Never exceed the recommended towing speed Always check tyre pressure before a journey Always check all lighting equipment is working correctly before a journey Check the wheel nuts after 25 miles 40km of service and subsequently before each journey Always make use of the breakaway cable Always apply the handbrake when the trailer is parked and when parking the trailer for a long period it is advised to chock the wheels and release the handbrake to avoid the brake shoes adhering to the brake drum surface The bed of the trailer should be level with the towing vehicle To achieve this it is recommended that provision be made to adjust the towing bracket or ball hitch Except in emergencies never unhitch the trailer from the towing vehicle If you have to unhitch with a load on the trailer take great care Make sure the jockey wheel is firmly clamped and the handbrake is applied fully also if on a slope chock the wheels as an added precaution f carrying a load on the trailer always ensure it is securely restrained and regular checks are made throughout the trio Used correctly and maintained to this handbook the trailer should give many years of safe and reliable service KA w SGS L Manufactured with Pride Page 1 OPERATING SAFETY INSTRUCTIONS COUPLING INSTRUCTIONS Wherever possible the vehicle and trailer should be on level ground Always check the condition of
15. pensators are at 90 to the brake rod with the brakes applied in forward and reverse Misalignment can be corrected through adjustment of the cable locking nuts This is particularly important if a new cable has been fitted 6 Operate handbrake and leave on Lower the trailer to the floor and recheck the tightness of the wheel nuts 7 Please note the brakes will not be 100 effective until the new linings have bedded in 8 The brake adjustment should be rechecked after a short journey WARNING The drums may be hot Manufactured with Pride Page 10 TRAILER USER S MANUAL Removal and Replacement of a Brake Cable Place the trailer on stands with all wheels free NOTE The handbrake lever should be secured in the off position 1 Undo the locknut on the brake rod front to rear adjacent to the compensator Slacken the second nut on the brake rod 2 Remove the nut from the cable inner and the nut retaining the outer to the bracket Take note of any washers and orientation of domed nuts Remove the half shell from the backplate and detach brake cable Withdraw the cable assembly 3 Attach the new brake cable to the expander in the hub and refit the half shell Thread the new cable into position secure the outer with its nut and thread the nut on the inner to approximately the position noted on the old cable NOTE This procedure covers just the brake cable replacement Nugent Trailers would always recommend that a full brake adjustm
16. plit pin 8 Refit the hub cap and replace wheels Check for excessive play at the wheel rim and repeat 7 5 if necessary 9 Adjust the brake linkage refer to adjustment procedure outlined later in this manual BRAKES Replacing Brake Shoes Place the trailer on stands with all wheels free NOTE The handbrake lever should be secured in the off position It is recommended that the brake shoes are replaced in axle sets Remove the wheels Remove the hub cap Slacken off the brake adjuster bolt until free Remove the axle nut this may be a castellated nut retained with a split pin or alternatively tt may be a locknut 5 Remove the brake drum hub puller may be required taking care not to displace the bearings WARNING Avoid inhaling brake dust Don t use an airline to clean the drum Carefully remove the dust using a small brush AUNI Fig 2 New sos 22 Manufactured with Pride Page 8 TRAILER USER S MANUAL 13 14 15 16 17 20 21 22 23 Check the condition of the brake drum replace the drum if deep score marks are visible Undo the locknut on the brake rod front to rear adjacent to the compensator Slacken the second nut on the brake rod Remove the half shell from the backplate and detach brake cable NOTE Record the orientation of the brake shoes and springs on the backplate to ensure that the new shoes and springs are replaced in the same position as the old See Fig 1 lef
17. rector of the Sellers CLAIMS PROCEDURE If you wish to make a claim under guarantee Immediately stop using the trailer List the details of the trailer and damaged items Consult with your supplier and have him forward your claim and the damaged item to Nugent Trailers Copyright Nugent Trailers 2014 All rights reserved NUGENT TRAILERS 44 0 28 8775 8583 Office 15 Aughnagar Road Galbally 44 0 28 8775 9910 Spare Parts Dungannon Co Tyrone 44 0 28 8775 8956 SGS l BT70 2PP N Ireland info nugenttrailers com Manufactured with Pride www nugenttrailers com
18. ree from knots Next attach the light kit from the socket on the trailer to the socket on your vehicle and check all the lights and indicators are working properly Release the trailer handbrake TOWING SPEED Speed limits The maximum speed for a car towing a trailer is GOmph 100kph on motorways and dual carriageways and 5Omph 80kph on other roads providing of course there is no lower speed limit in force at the time Vehicles are prohibited from using the overtaking lane of a three lane carriageway whilst towing The above are maximum speed limits but the user is strongly advised that speed is reduced when transporting livestock or any unevenly distributed load Manufactured with Pride Page 2 TRAILER USER S MANUAL TYRES It is very important to maintain tyre pressure at the required pressure If the pressure gets too low then it will adversely affect handling and fuel consumption and will lead to premature wear If seriously below par a tyre will overheat and fail very rapidly When a tyre does wear down it is very important it is replaced with the same size and load speed index rating as the one that is already on the trailer This information will be moulded onto the tyre sidewall e g 185 70 R 13C Use of a tyre with a lower rating can be dangerous Trailer tyres have to comply with exactly the same policy for conditions and thread depth as those for cars and light vans Radial and Cross Ply tyres must not be mixed on
19. square to the bore and seats against the shoulder the circlips are then re fitted 6 2 Fit the drum to the axle shaft and tighten the nut to the correct torque 280 Nm Note This type of bearing uses a very high torque nut which may only be used twice so if history is not Known it must be replaced 7 0 Individual taper roller bearings comprise inner and outer bearings and a separate seal These are adjustable but before adjustment is carried out the condition of the bearings must be identified 7 1 Wash grease and oil from the bearing with a suitable solvent inspect each roller inner and outer races If any pitting damage or corrosion is present then the bearing must be replaced NOTE If any one part shows damage or wear it is advisable to replace all bearings in the hub and fit a new oil seal 7 2 Using a brass drift carefully drive out the outer races working around the circumference 7 3 Clean the hub and carefully tap in the new bearing outer races with a brass drift Ensure bearings are seated against the shoulders 7 4 Grease the bearings and fit with a new seal Force grease into the bearing between each roller apply a light coat of grease to the bearing races Manufactured with Pride Page f OPERATING SAFETY INSTRUCTIONS 7 5 Fit the drum to the axle shaft and tighten to 7ONm torque rotating the Drum slowly Loosen the nut do not rotate the drum and finger tighten the nut back off to the first castellation and fit a new s
20. t hand and Fig 2 right hand for reference to Knott 200x50 brake others similar With care and using a suitable lever lift sliding shoe carrier away from expander Extract expander and retain Remove brake shoe retaining spring taking care to retain the spring Keep plate or pin at the rear of the backplate where fitted Lift off whole brake shoe assembly from backplate Take care not to lose the two adjuster wedges Examine the components and springs replace any damaged parts Clean the mechanism and ensure that all parts are free to move NOTE Do not lubricate Re fit springs to new shoes Locate shoes onto the backplate and position onto the adjuster wedges or cam block Re fit retaining springs Locate expander into position on fixed shoe With care and using a suitable lever position the expander between the shoes and release the lever Attach brake cable and refit the half shell NOTE Always replace the brake cables if they show sign of wear stiffness damage or fraying Re fit the drum and bearing Replace the split pin or lock nut dependent on which type of nut is used Generally speaking if a split pin and castellated nut is fitted the axle nut must be adjusted to allow the correct bearing clearance When the locknut is used it is normally tightened to a pre determined torque See Hub Bearing Section above Refit the hub cap Repeat the procedure on the other drum s Replace wheels Follow
21. the police in making a positive identification we recommend that the trailer is marked with the end users personal mark For additional security various types of coupling locks and security mechanisms are available on the market SPARE PARTS Spare parts for Nugent Trailers are readily available Please consult your Nugent Trailer Dealer for details and prices It is in the interest of the customer to use spare parts manufactured and supplied by Nugent Trailers Parts not so supplied may not be relied upon for correct material dimension or finish Nugent Trailers cannot therefore be responsible for consequential damage arising from the use of such unapproved spares and the Guarantee will become invalid Manufactured with Pride Page 16 Appendix 1 Fault Diagnosis and Remedies FAULT POSSIBLE CAUSE REMEDY OOOO O O O O S O m O O a a l a a a ae a ae ee Handbrake weak Braking system set incorrectly Check and re set to eliminate excessive travel Uneven or jerky braking Hore ooon ai InN le sg SSE mn Check and re set a ce O T a e O M O OO n OO OO E O o a O O T Excessive play between coupling head and towball Coupling head worn Replace Adjust load to give between 50 and 100Kg Trailer Snaking Incorrect nose weight on trailer Nose Weight on trailer coupling unless trailer is very light ci y ko SGS l Manufactured with Pride Page 17 Appendix 2 Maintenance Schedul
22. the brake adjustment procedure below Manufactured with Pride Page 9 OPERATING SAFETY INSTRUCTIONS Brake Adjustment NOTE When adjusting the brake drum only turn the wheel in the direction of forward rotation Ensure that the coupling drawtube is fully extended and that there is no tension in the brake rod or cables 1 Turn each wheel in the direction of forward rotation Turn the brake adjuster bolt clockwise until some resistance is felt as the brake shoes begin to grip the drum then slowly turn the brake adjuster bolt anticlockwise until the wheel begins to rotate freely again 2 Turn the nut on the brake rod until the nut is in contact with the compensator CAUTION Do not over tighten as this will cause the brakes to drag and overheat 3 WARNING Double check that everything has been re assembled with all fasteners secure Operate the handbrake several times to ensure that the compensators are seated Check the travel of the individual brake cables This should be 2 5mm If not re adjust the brake as appropriate 4 With the handbrake engaged turn each wheel in the reverse direction They should turn a little and then lock as the auto reverse mechanism operates NOTE As each wheel is turned there will be a rearward movement of the handbrake lever as the energy store operates This action should occur once on the rearward turn of each wheel If any wheel fails to lock there is too much slack in the system 5 Check the com
23. the same axle PARKING Parking the trailer on level ground or downhill Apply both the vehicle and trailer handbrakes Remove the light plug from your vehicle socket and stow away in a safe position Release jockey wheel clamp and lower the jockey wheel to the ground Firmly re tighten clamp by hand Turn the jockey wheel jack handle so that it raises the coupling free of the coupling ball Detach the breakaway cable Parking the trailer facing uphill Apply both the vehicle and trailer handbrakes Then return to the towing vehicle and release the handbrake The trailer should then roll back a few inches as the handbrake applies the brakes overriding the auto reverse system Re apply the towing vehicle handbrake Check the trailer handbrake is fully applied Remove the light plug from your vehicle socket and stow away in a safe position Release jockey wheel clamp and lower the jockey wheel to the ground Firmly re tighten clamp by hand Turn the jockey wheel jack handle so that it raises the coupling free of the coupling ball ensuring all the trailer wheels remain in contact with the ground Detach the breakaway cable NEVER DETACH THE BREAKAWAY CABLE BEFORE UNCOUPLING THE TRAILER Manufactured with Pride Page 3 OPERATING SAFETY INSTRUCTIONS If the trailer is to be parked for a long period it is worthwhile to chock the wheels and release the handbrake to avoid the possibility of the brake shoes adheri
Download Pdf Manuals
Related Search