VX800 User Manual
Contents
1. TER J 2 DIGITS 01 99 ae ai LE 05 5 SECONDS 00 REMAIN OPEN TIME a PRESS ENTER ENTER RELAY 3 TO 6 DIGITS 2 CODE PRESS ENTER a ENTER RELAY 2 DIGITS 01 99 2 TIME i PRESS ENTER a PRESS ENTER TWICE SYSTEM RED LED WILL GO OUT READY TO USE J MELODY NOTE TO EXIT BEFORE THE END FROM PROGRAM MODE PRESS ENTER TWICE RED LED WILL GO OUT d a TO USE SYSTEM ENTER CODE AND PRESS ENTER RELAY WILL OPERATE FOR PROGRAMMED TIME IF YOU WANT TO CANCEL REMAIN OPEN TIME ENTER CODE AND PRESS CLEAR IF YOU WANT TO OPERATE RELAYS TOGETHER YOU MUST PROGRAM SAME CODE FOR EVERY RELAY2. VX 800 INSTRUCTION MODELS VX800 2 Module 2 Relay VX800 2L Module 2 Relay plus panel illumination VX800 F Stand alone unit 2 Relay Flush mounting Vx800 S_ Stand alone unit 2 relay Surface mounting VxX800 3 3 Relay VX800 3L 3 Relay plus panel illumination INSTALLATION 2 RELAY SYSTEM 1 Power up 12 Volts Ac or Dc 2 Tap in pre factory code 6x1 111111 and press ENTER PROG led will illuminate 3 Tap in 3 to 6 digit master code and press ENTER 4 Tap in 3 to 6 digit 1st relay code and press ENTER 5 Tap in 2 digit relay operation time 1 to 99 sec and press ENTER I E 01 1sec 99 99 sec 00 Remain open operation 6 Tap in 3 to 6 digit 2nd relay code and press ENTER 7 Tap in 2 digit relay operation time as instruction 5 8 Press ENTER twice PROG led will go out System is now ready to use If an entry or exit button is required on 2 relay model only connect button terminals 9 10 When push button is pressed relay No 1 will operate for its programmed time If this function is only required at certain times connect a time clock in series with one leg of push button NOTES If only one relay is required press ENTER twice after instruction number 5 For 3 RELAY SYSTEM repeat 6 and 7 To cancel any code while operating tap in relevant code and press CLEAR button To change codes enter master code and proceed from instruction number 3 All relays can have same code if required Any number of rela
3. ys can be operated at same time if required f a wrong code is entered the system will lock out for 5 seconds which will increase each time a wrong code is entered The system will operate once the correct code is entered INSTRUCTION TO RETURN SYSTEM TO PRESET MASTER FACTORY CODE 1 Turn off power to code lock 2 Keep ENTER button depressed on code lock Turn back on power to code lock making sure ENTER button is depressed all the time Release ENTER button Code lock is now set at factory master code 6 X 1 111111 Proceed with programming for a new system oa kh amp Li TECHNICAL INFORMATION Power requirements 12 14 Vac or dc Min 15 mA at 12 Vdc without lamp and relays in rest position Max 315 mA at 14 Vac with lamp illumination and 3 relays activated stand 2nd relay have NO NC contacts 3rd relay NO contact only Max of contacts 5A 24Vac or DC If help is required for installing or operating this unit please contact our technical department on 39 734 631669 all countries or 091 224 3174 UK VX 800 SERIES TO SET UP SYSTEM TO ENTER NEW RELAY CODE POWER UP WITH 12 VOLT AC OR DC PRESS ENTER RED LED WILL ILLUMINATE ENTER NEW 6X1 111111 OR EXISTING 3 TO 6 DIGITS MASTER CODE RED LET WILL PRESS ENTER ILLUMINATE ENTER PRESET FACTORY CODE PRESS ENTER ENTER MASTER CODE 3 TO 6 DIGITD PRESS ENTER ENTER RELAY 1CODE 3 TO 6 DIGITS PRESS EN
Download Pdf Manuals
Related Search