USERS GUIDE 1 Gang Decora® 8 Button Wall Plate Controller
Contents
1. Please make sure the following items are included within your package Contact your dealer if any items are missing or damaged e DXB 8 x 1 e 1 Gang Decora Paintable White Wall Plate Optional Accessories e 5v DC power Supply for stand alone operation PS0045 5 Note Go to www auroramm com for latest manual and firmware User Guide INTRODUCTION About The DXB 8 is a low cost 8 button single gang button panel Designed to work with just about any RS 232 device on the market the DXB 8 allows any RS 232 string to be assigned to the press and release of each button Advanced functionality is available like repeat on hold Toggle macro delay between multiple commands and interlocking buttons for transport controls power on off etc The buttons can individually be lit red green or blue so in dimly lit areas it can be seen There are over 60 different laser etched button types available as well as custom laser etching Available in Decora white or black the DXB 8 is designed to match Low cost low power simplicity and compatibility with just about any device on the market makes the DXB 8 the simple sweet solution of choice Features 8 backlit buttons Red Green Blue Fits in standard 1 gang Decora style outlet 2 RS 232 ports Buttons individually programmable for RS 232 command Programmable on Press Release Toggle and Hold Macro functions and interlocking buttons 9600 115k Baud Rate Selectable Designed to2. after finger is removed from button and the Push string only will be sent Next button press will cause LED to light RED for release state and the release state string assignment will be sent out and not the push This will keep repeating back and forth every time the button Is pressed RS 232 Command Usage Example Example String Example Response Send Hello World on button 2 press on unit address 1 port 1 11PS1 2 Hello_World lt cr gt 1PS1 2 Hello_World lt cr gt Send 0x02 PON 0x03 on button 3 release eet on unit address 1 port 1 11RS1 3 02PON 03 lt cr gt 1RS1 3 02PON 03 lt cr gt every 100ms on unit address 1 port 1 11HS1 8 Hello World lt cr gt 1HS1 8 Hello World lt cr gt Set Unit Address 1 Port 1 Baud Rate to es eee 96008N1 11BR1 9600 8N1 lt cr gt 1BR1 9600 8N1 lt cr gt Set Unit Address 2 button 1 Release to green and Push to Red with no toggle mode 12BL1 G R 0 lt CR gt 2BL1 G R 0 lt CR gt Force change to address 5 IOADDR5 lt cr gt No response when 0 is used Query the push string state Unit responds with Hello World on button 1 press on unit address 4 port 2 4PS2 1 lt cr gt 4PS2 1 Hello_World lt cr gt Query the release string state Unit responds with Hello_ There on button 1 press on unit address 3 port 1 3RS1 1 lt cr gt 3RS1 1 Hello_There lt cr gt Jecryl0Onsonuntadiress1 pert Last tNSt ele en every 100ms on unit address 1 port 1 1HS1 1 lt cr gt 1HS1 1 Hello_World lt cr gt Get e
3. auroramm com S Ma G nn 4 T ersion 1 0b Settings Help 0 v seconds B gt ight Bed Green e Blue _ None Bed Green Blue _ None _ Toggle Backight t Red _ Green Blue _None Red Green Blue _ None _ Toggle Backlight a Gao ght Red Geen Blue None Red Geo Blue _ None eme Backlight EE Repeat every 0 7 seconds ve light Red Green e Blue Lt ee COES i ue Green Blue None _ Toggle Backlight e o eee e ae a5 D ight _Red _ Green Blue _None Hedi Green Blue _ None _ Toggle Backlight C em ht Bed _ Green Blue _None Bed Green e Blue None _ Toggle Backlight SSS Se Ss SSS ae ee Repeat every o 0 seconds ov o seconds Ale seconds cklight Red Green Blue None Red Green Blue None Toggle Backlight None User Guide BUTTON CAP SELECTION Button Caps The DXB 8 buttons are removable and can be replaced with a variety of buttons listed on the chart below in white or black For caps not listed on the chart custom laser etched button caps are available for a one time processing fee to accommodate any install Check with sales auroramm com for more information DXB 8 Button Cap Selection Chart A B C D E F G H J K 0 EEN 3 YPbPr VCR VTC VGA VGA1 VGA2 SCRN SCRN UP DN me BLANK BUTTON Buttons can be reversed 180 Note Part Number DXB C Row Column Letter B W B Black W White 4B Play Left and Righ
4. have affected the performance safety or reliability of the product F Part s are no longer available for product In the event that the product needs repair or replacement during the specified warranty period product should be shipped back to Manufacturer at Purchaser s expense Repaired or replaced product shall be returned to Purchaser by standard shipping methods at Manufacturer s discretion Express shipping will be at the expense of the Purchaser If Purchaser resides outside the contiguous US return shipping shall be at Purchaser s expense No other warranty express or implied other than Manufacturer s shall apply Manufacturer does not assume any responsibility for consequential damages expenses or loss of revenue or property inconvenience or interruption in operation experienced by the customer due to a malfunction of the purchased equipment No warranty service performed on any product shall extend the applicable warranty period This warranty does not cover damage to the equipment during shipping and Manufacturer assumes no responsibility for such damage 18 WWww auroramm com Aurora Multimedia Corp 205 Commercial Court Morganville NJ 07751 Phone 732 591 5800 Fax 732 591 6801
5. lt cr gt x Unit address 0 8 Address Zero is received by all but no String response from units Response only when set to address 1 8 99 Bytes Max Factory default is address 1 y Button Number 1 8 z Command string is in ASCII to be executed when a button is pressed Can be any valid serial command with the Unit address set to 0 Commands start with a Best command to use with this feature is the Button LED Setup All command as it allows one button to effect the status of the other buttons for an interlocking effect Button 1 telling other buttons new LED states when pressed In this example button 1 would turn green while button 2 turns red Great for Power on off interlocking button effect or transport controls for a DVD player etc 10CS1 0BA G R R N N N N N N N N N N N N N lt cr gt Setup Volume IxVBy b c tt lt cr gt x Unit address 0 8 Address Zero is received by all but no Cmd Preset response from units Response only when set to address 1 8 Buttons Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 for Volume up c Button Number 1 8 for Volume down tt repeat timing First digit is seconds second digit is tenths Setup IxVS s1 52 53 54 55 x Unit address 0 8 Address Zero is received by all but no Volume Cmd 56 57 58 S9 S10 511 response from units Response only when set to address 1 8 Presets el iert Factory default is address 1 s1 s12 strings one for each dis
6. when the product is left unattended for a long period disconnect it from the power source Also follow these precautions Ventilation Do not block the ventilation slots if applicable on the product or place any heavy object on top of it Blocking the air flow could cause damage Arrange components so that air can flow freely Ensure that there is adequate ventilation if the product is placed in a stand or cabinet Put the product in a properly ventilated area away from direct sunlight or any source of heat Overheating Avoid stacking the Aurora product on top of a hot component such as a power amplifier Risk of Fire Do not place unit on top of any easily combustible material such as carpet or fabric Proper Connections Be sure all cables and equipment are connected to the unit as described in this manual Object Entry To avoid electric shock never stick anything in the slots on the case or remove the cover Water Exposure To reduce the risk of fire or electric shock do not expose to rain or moisture Cleaning Do not use liquid or aerosol cleaners to clean this unit Always unplug the power to the device before cleaning ESD Handle this unit with proper ESD care Failure to do so can result in failure FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interferen
7. work seamlessly with DXW 2 Series Customizable laser etched buttons Daisy Chain up to 8 units for multi gang button panels Low Power 5v DC powered gt gt gt gt gt gt gt gt Low Depth 48 for Floor amp Table Boxes User Guide Front DXB 8 Front e Buttons There are 8 backlit buttons ON OFF VGA HDMI Up Arrow Down Arrow Speaker Mute and Mic Mute These laser etched buttons come as a default with the DXB 8 Other customizable buttons are available The LED backlighting can be set to light red green or blue The default scheme is to match the DXW 2 wall plate series to remotely select the inputs and to also control the display User Guide Rear DXB 8 D 2 7 Urora Multimedia XB 8 Rear Connections e RS 232 1 Connect RS 232 device up to 115k baud Note there is a 5v line as it is designed to power the DXB 8 from the DXW 2 wall plate or an option 5v supply for stand alone operation with any RS 232 device e RS 232 2 Connect RS 232 device up to 115k baud Units can be linked together to create larger button arrays by feeding port 2 of first unit into port 1 of next unit in line By repeating this process from unit to unit the commands can pass through from one the next Make certain to null the TX and RX In other words TX should go to RX and RX should go to TX from unit to unit The RS 232 protocol is designed to communicate to the address of a specif
8. B Blue N None t toggle mode 0 or 1 off or on x Unit address 0 8 Address Zero is received by all but no response from units Response only when set to address 1 8 Factory default is address 1 r1 r8 Release LED State R G B N R Red G Green B Blue N None X Ignore p1 p8 Pushed LED State R G B N R Red G Green B Blue N None X Ignore Send String to 8PD z lt cr gt Zz string is in ASCII and can have non printable as ASCII characters Address 8 in as well To send non printable ASCII Hexadecimal use a in front Daisy Chain of the 2 ASCII digits To send then use Example Line Feed Mode Ox0A Hex will be 0A Button LED Setup xBA p1 r1 p2 r2 p3 All 13 p4 r4 05 r5 p6 r 6 p7 r7 p8 r8 lt cr gt Set Address xADDRy lt cr gt x 0 8 This allows know address to be reassigned or use 0 to force to new address y Address 1 8 Query Firmware xFM lt cr gt x Address 0 8 Address Zero forces response regardless of unit Revision address Query Button xPSy b lt cr gt x Unit address 0 8 Address Zero is received by all but no Push String response from units Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 Query Button xRSy b lt cr gt x Unit address 0 8 Address Zero forces response regardless of Release String unit address Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 Query Hold St
9. cations subject to change without notice 17 User Guide APPENDIX A Warranty Limited 3 Year Warranty Aurora Multimedia Corp Manufacturer warrants that this product is free of defects in both materials and workmanship for a period of 3 years as defined herein for parts and labor from date of purchase This Limited Warranty covers products purchased in the year of 2009 and after Motorized mechanical parts Hard Drives DVD etc mechanical parts buttons doors etc remotes and cables are covered for a period of 1 year Touch screen displays are covered for 1 year touch screen overlay components are covered for 90 days Supplied batteries are not covered by this warranty During the warranty period and upon proof of purchase the product will be repaired or replaced with same or similar model at our option without charge for parts or labor for the specified product lifetime warranty period This warranty shall not apply if any of the following A The product has been damaged by negligence accident lightning water act of God or mishandling or B The product has not been operated in accordance with procedures specified in operating instructions or C The product has been repaired and or altered by other than manufacturer or authorized service center or D The product s original serial number has been modified or removed or E External equipment other than supplied by manufacturer in determination of manufacturer shall
10. ces received including interference that may cause undesired operation ce A Trademarks All trademarks in this document are the properties of their respective owners User Guide TABLE OF CONTENTS PACKAGE CONTENTS sietresecee ses ceeeaccnen ccc cepeestwecs cbse acaseseeatcucsetesunceceessvi veauvatavevaresmeusaseeeweeseceecuseass 1 INTRODUC TION BE 2 EEN 2 SM 2 FOM OAB O morea e E E E E 3 Koa RA 4 APPLICATIONS oenina E EE EEE 5 DXB 8 Controlling DXW 2EU amp broiechor 5 DXB Daisy Chan Ree EE 7 BUTTON SETUP allen t el LE 6 EIT GOI SS HO E 6 PROGRAMMING SOFTWARE cccccceseceseccnseceneecnsecenseenneneaseonsecenssonsecesssensenaaseonseoenesoaseneaes 8 DMC Ee 8 BUTTON GAP SELECTION sesiscceiscsacctssccticaunscasaccenidcasuedssucewuussinansmendeosssweudupecawadancupsmudswecanutcansacks H 5101000 41 0 eaen E E a E E E E E A 9 SERIAL COMMANDS nonnnnnnnnnnnnnnnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen nnmnnn nnen 10 Fee OGONI S e a e eene 10 FAO MANO tS ACS EE 14 APPENDIX 1 Troubleshooting cccceeeeseeeeeseeeeeneeeeenseeseeseeeeenseeeeaseeeenseeeoenseseonnessonseeses 15 APPENDIX 2 Firmware Update ccccececccesseecceneeeeesseeeenseeeeneeseenseeeeseesoessessenseesenseeses 16 DAB SUPA Re E 16 APPENDIX 3 Technical Specifications ccccessseeeceesseceeeeseeeseeeseeeseeenseeseennseeseoneeesees 17 APPEND A NEE 18 User Guide PACKAGE CONTENTS
11. co Aurora DXB 8 1 Gang Decora 8 Button Wall Plate Controller Manual Number 150227 Firmware v0 7 amp above User Guide SAFETY INSTRUCTIONS Please review the following safety precautions If this is the first time using this model then read this manual before installing or using the product If the product is not functioning properly please contact your local dealer or Aurora for further instructions A The lightning symbol in the triangle is used to alert you to the presence of dangerous voltage inside the product that may be sufficient to constitute a risk of electric shock to anyone opening the case It is also used to indicate improper installation or handling of the product that could damage the electrical system in the product or in other equipment attached to the product bg The exclamation point in the triangle is used to alert you to important operating and maintenance instructions Failure to follow these instructions could result in injury to you or damage to the product AN Be careful with electricity Power outlet To prevent electric shock be sure the electrical plug used on the product power cord matches the electrical outlet used to supply power to the Aurora product Use only the power adapter and power connection cables designed for this unit Power cord Be sure the power cord is routed so that it will not be stepped on or pinched by heavy items Lightning For protection from lightning or
12. crete volume level and can have non printable as ASCII characters as well To send non printable ASCII Hexadecimal use a in front of the 2 ASCII digits To send then use Example Line Feed OxOA Hex will be 0A Also the comma must be prefaced with a in the strings To send use To disable any unused level enter 00 in the remaining unwanted fields All used fields must start at field str1 and be in sequential fields Typical application might be for discrete steps of volume control The below commands set levels from 0 11 Note You must disable any unused positions with 00 as shown here position 12 11VS VOLO 0D VOL1 0D VOL2 0D VOL3 0D VOL4 0D VOL5 0D V OL6 0D VOL7 0D VOL8 0D VOL9 0D VOL10 0D 00 lt CR gt Baud Rate Setup IxBRy a b lt cr gt x Unit address 0 8 Address Zero is received by all but no Command response from units Response only when set to address 1 8 Factory default is address 1 y port number 1 or 2 a baud rate 2400 4800 9600 19200 38400 57600 115200 b bits parity stop 8N1 8E1 801 Button LED Setup xBLy z1 z2 t lt cr gt x Unit address 0 8 Address Zero is received by all but no Individual response from units Response only when set to address 1 8 Factory default is address 1 12 User Guide y Button Number z1 Release LED State R G B N R Red G Green B Blue N None z2 Pushed LED State R G B N R Red G Green
13. digit after for delays between commands in a string to create a Macro A 0 9 will follow the Each number is a multiple of 100ms delay so 8 is 800ms If character is require to be sent for none delay purpose then a must be used 11HS1 1 03 Hello string 1 0D 5Hello string 2 0D lt cr gt Holding button 1 will send on serial port 1 every 300ms Hello string 1 lt cr gt Delay 500ms Hello string 2 lt cr gt x Unit address 0 8 Address Zero is received by all but no response from units Response only when set to address 1 8 Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 i Instance Number 1 or 2 LED Color R G B N R Red G Green B Blue N None Zz string is in ASCII and can have non printable as ASCII characters as well To send non printable ASCII Hexadecimal use a in front of the 2 ASCII digits To send then use Example Line Feed Ox0A Hex will be 0A Delay Delimiter is used with a single digit after for delays between commands in a string to create a Macro A 0 9 will follow the Each number is a multiple of 100ms delay so 8 is 800ms If character is require to be sent for none delay purpose then a must be used 11TG1 1 2 R Hello string 1 O0D 5Hello string 2 0D lt cr gt Pressing button 1 will send on serial port 1 Hello string 1 lt cr gt Delay 500ms Hello string 2 lt cr gt 11 User Guide Button Command xCSy z
14. er om Lomsmge Unit responded with 384008N1 1BR1 lt cr gt 1BR1 38400 8N1 lt cr gt Query Unit Address 2 button 3 LED state The response for this example will be release Blue Push Red and toggle mode on 2BL3 lt CR gt 2BL3 B R 1 lt CR gt 14 User Guide APPENDIX 1 Troubleshooting 1 LED is not lit on any buttons 2 RS 232 does not work 3 Some functions do not work v jopo Check 5v power supply is plugged in locally or if connected to DXW 2 make certain the DXW 2 has power Check to see if Wall supply is plugged into wall outlet Make certain wall outlet has power Make certain RS 232 command for LED state is not set to none for the buttons Check connection on RS 232 port Make certain TX goes to RX and RX goes to TX of the device to be connected Don t forget about ground Check baud rate Verify commands being sent are correct protocol Each unit must have a unique address Make certain unit has latest firmware 15 User Guide APPENDIX 2 Firmware Update DXB 8 Update Utility DXB 8 Update Software requires a serial cable connected in a null RX to TX TX to RX GND to GND configuration to a PC The firmware can be updated directly at either of the DXB 8 rear serial ports To force update mode holding buttons 1 amp 8 for 5 seconds will force unit into firmware update mode for port 1 and holding buttons 4 amp 5 for 5 seconds will force unit into firmware update mode for
15. ic unit so it is important to make certain each unit has a unique address and the same baud rate User Guide APPLICATIONS DXB 8 Controlling DXW 2EU amp Projector The example below demonstrates the DXB controlling a DXW 2 series wall plate which in turn passes the RS 232 to the DXE CAT series receiver The DXE CAT receiver RS 232 port is connected to the projector DXB 8 Controlling DXW 2EU amp Projector User Guide BUTTON SETUP FUNCTIONS Button Setup Buttons are referenced 1 8 starting in upper left to lower left for 1 4 and upper right to lower right for 5 8 1 Unit Address Holding buttons 1 amp 4 down for 5 sec will allow user to press button 1 through 8 to set address accordingly When the 5 sec is reached current address will show by blinking button relative to address blue Next user will press any of the 8 buttons to set new address Once button is pressed a confirmation will happen by flashing new address buttons LED RED then green then off as it exits the mode of operation 2 Factory Test Holding buttons 5 amp 8 down for 5 sec will do factory test Factory test is light all buttons Red for 2 sec Blue for 2 sec amp Green for 2 second Next it will blink a red LED starting at button 1 When pressed next button in order will blink red and prior button will turn off until all 8 buttons are pressed After button 8 is pressed unit will finish with RS 232 loop test from port 1 to port 2 to verify back and forth comm
16. or User Guide DXB 8 Daisy Chain Mode The DXB 8 units can be combined up to 8 total allowing multiple units to function as a single control interface All commands when operated in this mode pass through to com1 of unt The last unit in the chain must always be address 8 in order to connect a device to communicate with port 2 The 8PD z lt cr gt z string command must be used to target a command out this port see RS 232 command section for proper usage If you are not using the last port in the chain then it will not be necessary Daisy Chain Mode Holding buttons 4 amp 8 for 2 seconds will enable daisy chain mode After 2 seconds all button LEDs will go off for 1 second then LEDs 1 4 5 and 8 will light for 1 second Red for daisy chain mode or Green for normal mode then all LEDs return to their normal color Unit 8 Unit 2 Unit 1 gt D EI wi 29 ee Drier Multimedia DXW 2 ve le Or Control System Display or gt other device User Guide PROGRAMMING SOFTWARE DX Interface DX Interface is a free utility for programming the buttons with the various functions It allows a user to assign RS 232 strings and LED color selection to the different button states These assignments can be applied to the push release and holding of the buttons Refer to Appendix 2 for cable connection to a PC DX Interface is designed to run on a Windows PC The latest versions of DX Interface can be downloaded from www
17. port 2 LED 1 will light blue when in the mode for port 1 update and LED 2 will light blue when in mode for port 2 update A way to force update if necessary is to hold buttons 7 amp 8 while applying power to the DXB 8 Next use utility to transfer file which can be found at www auroramm com Pin 3 Transmit Bin 2 Data TD Receive Data Pin 4 Pin 1 RD Data Terminal Data Carrier Ready DT R Detect DOD not used not used Pin 5 ei Ground Pin 6 Data Set Ready DSR not used Ringing Indicator RI net used Pin Ping Request to Clear to Send Send ATS end RTS cts PC DB 9 RS 232 Serial Port 16 User Guide APPENDIX 3 Technical Specifications Model Name DXB 8 Technical DXB 8 RS 232 Baud Rate Max 115kbps Factory default is 9600 Front Selections 8 Backlit Buttons Red Green Blue RS 232 Connector Port 1 4 pin 3 81mm Euro RS 232 Connector Port 2 3 pin 3 81mm Euro DXB 8 Housing Plastic front with aluminum rear enclosure Dimensions 1 44 x4 331 x 76 Lx W x D Note Wall box portion depth 48 Weight 38lbs Mounting Wall mounting Decora 1 Gang Power suppl 5v 300mA DC Power consumption 1 Watts max 0 40 C 32 104 F 20 60 C 4 140 F 20 90 RH no condensation 1x DXB 8 Package Contents 1x Paintable White Wall Plate 1x User Manual Operation temperature Storage temperature Relative humidit 5v DC power Supply for stand alone operation PS0045 5 Specifi
18. ring xHSy b lt cr gt x Unit address 0 8 Address Zero forces response regardless of unit address Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 x Unit address 0 8 Address Zero forces response regardless of xTGy b i lt cr gt Query Toggle unit address Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 String Instance Number 1 or 2 Query Baud Rate xBRy lt cr gt x Unit address 0 8 Address Zero forces response regardless of Setup unit address Factory default is address 1 y port number 1 or 2 Query Button LED xBLy lt cr gt x Unit address 0 8 Address Zero forces response regardless of Setup Individual unit address Factory default is address 1 y Button Number Query Button LED x Unit address 0 8 Address Zero is received by all but no Setup All response from units Response only when set to address 1 8 Factory default is address 1 13 User Guide RS 232 commands can be sent to the RS 232 port 1 or 2 Buttons are referenced 1 8 starting in upper left to lower left for 1 4 and upper right to lower right for 5 8 Note Button LED Setup Command button toggle mode allows a button to change between push and release states per individual push For example if release LED is RED and string assigned is OFF and Push LED is Green and string assigned is ON when user presses button for first time Push LED will light and stay lit even
19. t 4D Fast Forward amp Rewind 4E Next and Prev 4F Up amp Down Blank button No LED backlight Part Number DXB CB B W B Black W White Example White PROJ Button PN DXB C2D W User Guide SERIAL COMMANDS RS 232 Commands Command Query Response lt cr gt 0x0D Hex 13 Decimal Do not confuse with delimiter 0D Command String Format Information Button Push IxPSy b z lt cr gt x Unit address 0 8 Address Zero is received by all but no String response from units Response only when set to address 1 8 99 Bytes Max Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 Zz string is in ASCII and can have non printable as ASCII characters as well To send non printable ASCII Hexadecimal use a in front of the 2 ASCII digits To send then use Example Line Feed Ox0A Hex will be 0A Delay Delimiter is used with a single digit after for delays between commands in a string to create a Macro A 0 9 will follow the Each number is a multiple of 100ms delay so 8 is 800ms If character is require to be sent for none delay purpose then a must be used 11PS1 1 Hello string 1 O0D 5Hello string 2 0D lt cr gt Pressing button 1 will send on serial port 1 Hello string 1 lt cr gt Delay 500ms Hello string 2 lt cr gt Button Release IxRSy b z lt cr gt x Unit address 0 8 Address Zero is received by all but no String response from units Response onl
20. unications LED 1 amp 2 will light blue and pressing button 1 will send string from port 1 to 2 and pressing button 2 will send string from port 2 to 1 During both it checks for proper response Send string test lt cr gt to be responded with test lt cr gt If it checks ok LED 4 will light Green for ok or Red for bad for port 1 Use LED 5 for port 2 indicator Once Port 2 test is done light blue LED 8 and when pressed End factory test mode by turning on on all 8 LEDs blue for 1 sec then off 3 Factory Reset Holding buttons 3 amp 4 down for 10 sec will do a factory reset Factory reset will set RS 232 ports 1 amp 2 to 96008N1 Unit address to 1 and assign strings on push for 1 1B1 lt cr gt for button 1 and increment accordingly for all 8 button The release will be set to 1 1R1 lt cr gt for button 1 and increment accordingly for all 8 buttons Hold will have nothing All LED will be defaulted to blue for press and release 4 Update Mode Port 1 Holding buttons 1 amp 8 gt 5 seconds will force unit into firmware update mode via port 1 5 Update Mode Port 2 Holding buttons 4 amp 5 gt 5 seconds will force unit into firmware update mode via port 2 6 Daisy Chain Mode Holding buttons 4 amp 8 for 2 seconds will enable daisy chain mode After 2 seconds all button LEDs will go off for 1 second then LEDs 1 4 5 and 8 will light for 1 second Red for daisy chain mode or Green for normal mode then all LEDs return to their normal col
21. y when set to address 1 8 99 Bytes Max Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 Zz string is in ASCII and can have non printable as ASCII characters as well To send non printable ASCII Hexadecimal use a in front of the 2 ASCII digits To send then use Example Line Feed Ox0A Hex will be 0A Delay Delimiter is used with a single digit after for delays between commands in a string to create a Macro A 0 9 will follow the Each number is a multiple of 100ms delay so 8 is 800ms If character is require to be sent for none delay purpose then a must be used 11RS1 1 Hello string 1 0D 5Hello string 2 0D lt cr gt Releasing button 1 will send on serial port 1 Hello string 1 lt cr gt 10 Hold String Toggle String IxHSy b tt z lt cr gt IxTGy b i z lt cr gt User Guide Delay 500ms Hello string 2 lt cr gt x Unit address 0 8 Address Zero is received by all but no response from units Response only when set to address 1 8 Factory default is address 1 y Port Number 1 or 2 b Button Number 1 8 tt repeat timing First digit is seconds second digit is tenths Zz string is in ASCII and can have non printable as ASCII characters as well To send non printable ASCII Hexadecimal use a in front of the 2 ASCII digits To send then use Example Line Feed Ox0A Hex will be 0A Delay Delimiter is used with a single
Download Pdf Manuals
Related Search