E-light System PRODUCT DESCRIPION
Contents
1. strong pulsed light device may cause hurt by improper handling Operators should keep Page 9 in 11 pages vigilant and take necessary protection measures according to the manual Operatee Carry out the treatment in the professional treatment room take effective eye protecting measure Operator wearing protective glasses Treatment room marked the treatment room clearly with in operating of IPL To ensure to the safe use of the equipment please read the following instructions carefully gt one except technician authorized by the manufacture could dismantle or repair the equipment especially for the power source handpiece high voltage electricity inside Voltage rating 110 120V Maintaining the equipment after disconnecting the power cord Keep the handpiece clean all the time do not let the gel leaking into the handpiece Vw V WV In case leaking of the handpiece do not start the equipment already started turning off immediately gt No emitting light to one area repeatedly otherwise may cause inflaming or burns and may leave pigmentation Alarms of Strong IPL gt IPL may hurt the eye or cause burns or fire take all necessary prevention measures before operating Emitting too much light to one part may burn the skin which may cause pigmentation Do not watch the IPL light directly from the handpiece even wearing protective glasses Do not emit the light to the air keep the handpiece on the hanger when not us2. E light System PRODUCT DESCRIPION Please read the instructions before use 22 2 20222220 10 4 0 21 00 000000000000005 1 1 V VITE REPRE 1 3 System SCL CHECIAIVO Nm 1 4 Accessories amp Connection Instruction sse 2 Il STANDARD TREATMENT PROCESS 2 esee 2 OPERATION INSTRUCTION eren 5 NM ce EY NOTICE woes 10 COV Ol ANON m 10 4 2 Safety of Electricity amp Machinery 11 ME TABOO INSTRUCTION iiia aepo eun E atra o Reip DEPO D S edat Eh 11 ATTENTIONS AFTER TREATMENT 112 WW WARRANTY RARO eI Ra MA 12 I Brief Introduction E light applies three core technology IPL RE and epidermis cooling It combines the advantage of IPL and RF in one hand the skin absorbs IPL energy selectively and the skin also absorbs RF energy on the other hand the RF surface touch cooling technology removing the discomfort and complications by high heat of IPL Therefore the effect and safety of E light makes a breakthrough Principle Applying the technique of IPL and Bi polar Radio Frequency the equipment acts on the entire skin corium and connective tissue stimulates the collagens of different depth to realign and grow then gets treatment effect Bio polar RF re
3. is no leaking of water circulation fold the protective cover by turning it right 3 5 Debugging 3 5 1 Make sure water and electric circuit is correct connected then turn on the power to start the machine 3 5 2 Turn on the master power switch on the backboard 3 5 3 Turn on the emergency switch clockwise turn in the front side of the mainframe 3 5 4 Turn on the key switch clockwise turn 3 5 5 Check is there any leaking of the water connectors 3 5 6 If the above is checked OK put the wire cover into the neck on the backboard then turn deasil to get fixed 3 6 Operation Enter operation condition after debugging and no abnormalities found 3 6 1 Treatment Selecting Interface e E LIGHT Page 5 in 11 pages Skin Rejuvenation e Pigmentation Therapy x Vascular Therapy A Acne Therapy AM Wrinkles Therapy Treatment Selection Interface Select the wanted treatment program by clicking 3 6 2 Operation Interface Page 6 in 11 pages e IPL ow 22 Removal uw M ae 5 Q E Ku Operation nid se 5 plusel 9 0 9 5 Treatment mode 3 groups of different parameters setting Pulsel working time of the first pulse delayl 9 Pluses sub pulse width irradiatingpume othgrdightexcept the first pulse Delayl Ist pulse delay delay
4. 0 1200nm Cooling water air semi conductor Spot size 8x40mm N W 35kg Voltage 110V 220 10 50 60Hz 3 Accessory List rofen Jom Jy p l Mainframe set 1 inthemaincase PN SR Handpiece m in the lateral foam box HR Handpiece in the lateral foam box 47 Power Cord pe I in the ltr Foam box 5 Key Switch pc 2 inthe lateral foam box 6 Goggles for Operator pair 1 _ in the lateral foam box 17 _ Goggles for Patient pair__ 1__ inthe lateral foam box Space Nite Pings pe L in he lara Zou pes Spare fuses 1 in the lateral foam box 10 User Manual pc l in the lateral foam box Standard Treatment Process 2 1 Form filling Fill in the blanks of the Client File confirm the treatment program remind the client pay Page 2 in 11 pages attention to some points before and after treatment 2 2 Face cleaning Clean the face with gentle face cream for 3 minutes Remind clean the hands of operator and the handpiece with bromogeramine 2 3 Preheating Start the equipment after face cleaning preheat for not less than 3 minutes without lighting the xenon lamp 2 4 Shaving Shave the unwanted hair of the treatment area 2 minutes 2 5 Gel coating Coating the gel evenly 2 3mm on the skin Effect light guide cooling anaesthetisin Attention no coating on eyes eyebrows lips 2 6 Eye protection Operator wear the safety goggles Patient close the eyes wear professional safety g
5. Chloasma Light pain light reddish redness disappear in 5 minutes After radiation the pigments become darker first in 10 days and decline in 15 days Don t adjust big parameter value to treat chloasma 1 2 treatment course needed for chloasma Parameter control Short pulse width long interval low energy 3 8 3 Epidermis spot The most difficult one so the treatment time 1s longer correspondingly IPL is the best way of removing epidermis spot With the cooperation of using laser 7 8 times radiation will cure the spot Parameter control Long pulse width short interval medium energy 3 8 4 Acne scar and other pigmentation Patient would have a strong pain under the limit of patient Pigmentation will decline 3 7 days Parameter control Long pulse width short interval high energy 3 8 5 Vascular redness Using high pulse width on the basis of easing the skin Parameter control Long pulse width long interval suitable energy 3 8 6 Bulky pore black head acne Strong pain under the limit Blackhead and oil comeout in 2 3 days and disappear in 7 days Parameter control Long pulse width short interval high energy Page 8 in 11 pages 3 8 7 Winkle pouch black circle Light pain Parameter control Short pulse width long interval suitable energy 3 8 8 Skin rejuvenation Strong pain under the patient limit reddish redness disappear in 10 minutes No suggesting repeat operation Parameter control Long pulse widt
6. h long interval high energy 3 8 9 Hair Removal Strong pain follicular orifice will become a little reddish with a burning smell Caution for arms lips and legs hair removal avoid pigmentation by over high energy According to the growing period of hairs growing period maturation period rest period 3 times of treatment will remove the hair completely Parameter control Long pulse width long interval suitable energy Special Attention For the sensitive and dark skin there might be delayed reaction in 24 48 hours therefore do not raise the energy casually Adjust the parameter value according to the whiteness of skin The whither the higher endurance of the skin is For dark skin please pay more attention to use long interval and suitable energy of parameter value V Safety Notice 4 1 Safety of E light The equipment takes maximum consideration of the safety of both operator and operatee in the designing the following are some safe measures of it Circuit self checking after machine starting Using filter light guide crystal strong pulse light comes out only from the front side of the handpiece gt Designed with independent safety circuit electricity could be shut down automatically when the IPL power is to high Emergency stop switch shut down the power in emergency Key switch to avoid starting the machine by any people gt Use high quality engineering plastic frame preventing electricity creepage Alarm
7. ing it 4 2 Electricity amp Machinery Safety Keep all the boards closed open the board may bring danger There is high voltage electricity inside some parts still carry electricity even after turn off the power therefore do not dismantle the backboard without under supervising by our technicians Do not move the equipment by pulling the handpiece Do not use the equipment in inflammable and explosive environment Do not use alcohol or acetone before treatment Page 10 in 11 pages gt Do not start operating before the handpiece dry enough after clean the handpiece or other parts of the equipment VI TABOO The following people 1s not suitable to be operated by the machine 1 pregnant high blood pressure heart attack diabetic 2 allergic to IPL 3 open wound parts 4 people who could not avoid strong sun light 5 scar birthmark or mole higher than the skin VI Attentions After Treatment 1 Not using irritative makeups 2 No hot water face wash or sauna in 7 days 3 No stimulating food or pigmentary food as chocolate coffee no smocking no drinking 5 No scratch in case of scabbing 6 Make a water replenishing care in 10 days Vil WARRANTY POLICY Page 11 in 11 pages
8. lease energy at the same time with the selective absorption for the skin to light energy various pathological tissues of corium and epidermis creates Photothermolysis effect Since light energy is far below conventional IPL the pigment tissue and vascular pathological tissue of the corium and epidermis would absorb more energy without injuring the epidermis and then remove these pathological tissues better and get the effect 2 Application 1 Hair removal 2 Skin reyuvenation Wrinkle removal fact lifting 3 Removing freckle age spots sun spots chloasma pigmentation troubles etc 4 Vascular removal 5 Acne treatment 3 System Self checking The circuit of system entering the self checking situation when the machine starts leave the machine carry on the self checking for 5 10 seconds then continue the operation 4 System Classification Electric shock protection Gradel Grade Corrosion prevention liquid ordinary Do not use the machine in the environment mixed of flammable narcotic and air or nitrogen Page 1 in 11 pages oxide mixture 5 Equipment Consist Specification and Accessory List 1 Equipment Consist 1 1 Mainframe A Power supply system B Microcomputer system C Monitor D Cooling System 1 2 E light Handpiece A Intense pulsed light source xenon lamp B Reflector and filter C Sapphire wave guide 2 Technique Specification Light Energy 1 50J cm2 RF energy 1 25 SR Spectra 53
9. oggles or cover the eyes with eye patch 2 7 Allergic test Emit 2 or 3 light spots in the bottom of ears in safe parameter observe for 3 minutes Effect do not continue to operate 1f there 1s a allergic phenomena 2 8 Operation Carry on the operation with a suitable parameter to the operatee Attention 2 8 1 Inform the operatee that there will be a slight pricking in operation before operating to avoid panic 2 8 2 Start the operation with a low energy grade adjust the parameters operating while asking the feeling of the operatee 2 8 3 Move the light spot by one spot overlapping the upper 1 3 part of the previous spot No emitting one area repeatedly otherwise may cause inflaming or burns 2 8 4 The handpiece should touch the skin vertically no over pressing or leaving the skin Page 3 in 11 pages 2 8 5 Observing the reaction of skin while operating 2 9 Cold compress Keep gel coating for 20 minutes after operation ending carry out cold compress in obvious slight reddish reaction till reddish fading away 2 10 Cleaning Clean the gel with cold water coat corresponding cosmetics 2 11 Treatment Course Skin Rejuvenation Program 30 45 days time 4 times course Hair Removal Program 2 3months time 3times course 2 12 Special reminding 2 12 1 Ask the client before treatment is there a allergic or not is there a bad reaction before for similar operation fill the Client File concretely Adjust the parameters on the basis of full acq
10. ok Pulse amount adjusting pulyeaypaunt of sagliiagieting RF Working time working time of counter 280 Repeat frequency interval between two Total counter accumulated spot piat o xeno Sy Status display back 3 water circulating status lamp stauts charging statu l Current temp back return to the previous interface IPL energy adjusting increase or decrease the IPL output energy RF energy adjusting increase or decrease the RF output energy Page 7 in 11 pages Cooling adjusting adjusting the cooling level pasue continue continue standby stautus parameters could be set in this stauts lamp is on but could not make shots start pause click start zimmer the handle and the capacitor charge automatically system will enter the treatment status when charge 15 ready Click stop escape from treatment stauts 3 8 Treatment Advice 3 8 1 Freckle age pigment strong pricking for the first treatment under the tolerance of the operatee One minute after receiving emitting there will be a slight reddish which will fade away in 10 minutes for someone special maybe 30 minutes Punctuate pigment will appear on the surface of skin and will be metabolized 3 7 days The one off curing rate of freckles by using E light is 6096 8096 normally freckles could be cured one course of treatment Parameter control Long pulse width short interval medium energy 3 8 2
11. uaintance of the condition of operatee Inform the operatee the possible reation in operation before operating 2 12 2 In large area treatment or long time continuous operating the water inside the equipment will warm up and the handpiece will be hot interrupt the operation to refresh the water or leave the water cool down to continue operating 2 12 3 Refresh the circulating water in one month use purified water or medical distilled water Operation Instruction 3 1 Before starting the machine 3 1 Accessories connecting 3 1 1 Connect the handpieces filters and probes 3 1 1 1 Put the handpiece on the hanger 3 1 1 2 Connect the handpiece Connect water pipes 2 signal wires 2 black to black red to red xenon lamp wire and RF wire to the corresponding jacks on the backboard tightly 3 1 2 Check the water holes of the backboard make sure the water outlet hole is plugged well 3 2 Water infusing 3 2 1 pull out the plug of the water inlet hole insert the water funnel 3 2 2 infuse water till water spill out from the spillway hole 3 3 Checking Page 4 in 11 pages 3 3 Make sure there is no water leaking 3 3 2 Make sure there is no moisture or wet for electricity connecting parts 3 3 3 Make sure the key switch is in the off position 3 3 4 Make sure the emergency stop switch is in the on position 3 4 Starting the equipment 3 4 1 Connect the power cord turn on the key switch 3 4 2 Double confirm there
Download Pdf Manuals
Related Search