Money Counter User M..
Contents
1. a new number for batch counting Accumulation Press Add key to set the machine to accumulating mode and add the count to the next count of bank notes The Add indicator will be lighted Put bank notes to be counted on the Hopper Plate and then the machine will automatically start counting this set of notes After counting put another set of bank notes on the Hopper Plate The current count of bank notes is added to the previous count and displayed on the Count Display MISCELLANEOUS Adjustments on the Hopper Plate Caution Switch off the machine and disconnect the power cable from the plug before checking the Hopper Plate Adjusting the Hopper System Adjust the Hopper Adjust Screws Changing the Resistance Rubber When the Resistance Rubber got worn out follow these steps to replace it 1 Remove the Hopper Plate Screw and the Hopper Springs 2 Replace it with the spare rubber attached in the package Adjusting the Plate Spring The Plate Spring should be 10mm 12mm away from the Resistance Rubber If the distance is too short bank notes can not be separated smoothly and if the distance is too long bank notes can not go down easily After making the necessary adjustments switch on the machine Test the system using one piece of note With one end in your hand let the other end go vertically to the Feed Rollers You should feel a balanced tension on both sides of the rollers The gap between the Hopper Plate and the Feed Ro2. Money Counter SPECIFICATIONS Counting Speed Banknote Sizes Banknote Thickness Hopper Capacity Display Alarm Display Batch Display Environmental Temperature Moisture Power Source Power Consumption Net Weight Gross Weight gt 1000 pcs 100 mm x 50 mm to 173 mm x 85 mm 0 075 mm to 0 015 mm 130 pcs LED 999 1 LED Display 3 LED Display 0 C to 40 C 30 to 90 110 V 60 Hz 220 V 50 Hz lt 70 Watts in operation lt 10 Watts when not in operation 6 5 Kg 7 0 Kg Money Counter 17 16 l 14 13 12 11 18 19 20 21 22 23 7 Preset Batch Key 10 ADD Key Accumulation 11 Stacker Plate 12 Stacker Sensor Hopper Plate System T Hopper Plate 2 Plate String 3 Resistance Rubber 4 Adjusters 5 Adjuster Spring FEATURES Automatic Self Test The machine will automatically perform selftest after power on Auto Stop on Foreign Abnormal Notes The machine will stop counting when it detects forged notes foreign notes jammed notes doubled notes broken notes etc The buzzer will alarm and the Preset Display will show the error code Error Codes Causes EC1 Half notes broken notes EC2 Doubled notes EC3 Chained notes EC4 Forged notes Common Counting The machine can count all bank notes being placed on the Hopper Plate Batch Counting The machine can count bank notes by batches Accumulation The machine can count all bank notes on the Hopper Plate and ca
3. llers can be adjusted by the Hopper Adjust Screws Turn clockwise to tighten the gap or turn it counter clockwise to loosen it Troubleshooting Error Signals Descriptions S Solutions UV i ER8 Left Counting Sensor is covered with dust Clean the Left Counting Left Counting Sensor is not positioned well Sensor Left Counting Sensor is broken Reposition the Left Counting Sensor Replace the Left Counting Sensor with a new one Right Counting Sensor is covered with dust Clean the Right Counting Right Counting Sensor is not positioned Sensor well Reposition the Right Counting Right Counting Sensor is broken Sensor Replace the Right Counting Sensor with a new one Hopper Sensor is covered with dust Clean the Hopper Sensor Hopper Sensor is not positioned well Reposition the Hopper Sensor Hopper Sensor is broken Replace the Hopper Sensor with a new one Stacker Sensor is covered with dust Clean the Stacker Sensor Stacker Sensor is not positioned well Reposition the Stacker Sensor Stacker Sensor is broken Replace the Stacker Sensor with a new one UV Sensor is covered with dust Clean the UV Sensor models UV Sensor is broken Replace the UV Sensor with a new one Width Detection Sensor does not have Adjust the voltage enough voltage Width Detection Sensor is broken Replace the Width Detection Sensor with a new one
4. n add the total number to the previous counts Auto Start The machine will automatically start counting when bank notes are put on the Hopper Plate Remove the notes from the Stacker when done so that the machine could reset and start counting again Auto Reset a When in normal counting mode the machine will automatically clear the sum after the counted notes on the Stacker are removed and another set of notes is placed into the Hopper Plate b When in batch counting mode the machine will clear the sum and will automatically reset after the counted notes on the Stacker are removed OPERATIONS Preparing the Money Counter for Use 1 Make sure that the power socket connected to the machine is in good grounding and power voltage is within the stated range Turn on the power supply and switch on the machine UV indicator is enabled and lighted when the machine is turned on The machine will then do automatic selftest Error codes will be displayed on the Preset Display when errors have been encountered The machine is initially set to Normal Counting mode The Count Display initially displays 0 and the Preset Display initially displays nothing Panel Key Functions 1 UV Key Press this key to enable or disable fluorescence test The UV indicator will be lighted if this function is enabled otherwise this indicator is switched off 2 Preset Key Press this key to clear Preset Display and to set the machine to Normal Coun
5. ting mode 3 Clearand Reset Key Press this key to clear and reset values 4 ADD Key Press this key to set the machine to Add or Accumulating mode 5 1 Key 6 x10 Key Press these keys to set batch number The batch number should be in the range of 1 to 999 Caution The panel keys should not be pressed when the machine is counting notes Pressing any keys while note counting is in progress could cause jamming or output problems Counting Modes 1 Normal Counting Mode Press the Preset key to clear Preset Display and set the machine to normal counting mode Put bank notes on the Hopper Fate and these will be automatically counted Results will be shown on the Count Display To count another set of bank notes remove the counted bank notes and put a new set on the Hopper Plate The machine will not start counting unless the counted notes are removed Batch Counting Mode Press the Preset key to clear Preset Display Set the batch number number of bank notes to count using 1 and x10 keys The batch number must be between 1 and 999 After setting the batch number put bank notes on the Hopper Plate and the machine will automatically start counting by batch It will automatically stop counting when the preset batch number is reached Remove the counted bank notes to start counting another batch Put more bank notes on the Hopper Plate if the current bank notes are insufficient The preset batch number will be overwritten each time you set
Download Pdf Manuals
Related Search