Pyle Backup Cameras & Sensors User Manual
Contents
1. to be vigilant in supervising children especially when children are in the yard driveway or parking lot playing near parked cars Roll down your window so you will be able to hear what is happening outside your vehicle Teach children to move away from a vehicle whenever it is started TESTING THE SYSTEM Connect vehicle battery cables Turn ignition to ON position without starting the engine Press monitor ON OFF power button to start monitor Engage parking brakes and put the car in reverse Wait for monitor to show rear view image If needed switch the image orientation to acquire the correct view Press the rotate button until desired image orientation is achieved aA A S a aat Na 1 2 3 4 5 6 BACKUP CAMERA SYSTEMS2. PYLE BEFORE using the Vehicle Back Up Camera please read the following safety information ALWAYS use the Vehicle Back Up Camera as outlined here A Warning A failure to read and follow these warnings and instructions may result in a serious accident including damaged property or a serious injury including loss of life The Vehicle Back Up Camera is designed as an aid to the driver in detect ing large stationary objects to help avoid damaging the vehicle However you the driver must use it safely and properly Never back up while looking only at the screen You should always check behind and around the vehicle when backing up just as you would if the vehicle did not have the Vehicle Back Up Camera Always make sure your intended path is clear Always back up slowly Never depend on the Vehicle Back Up Camera entirely when backing up The image on the screen is different from actual conditions Objects viewed in the rear view monitor differ from actual distance because a wide angle lens is used Objects in the rear view monitor will appear visually opposite than when viewed in the rear view and outside mirrors Use the inside mirror or glance over your shoulder to properly judge distances to other objects The Vehicle Back Up Camera s night vision feature is only an aid to a driver but is limited Always use your own eyes to confirm the vehicle s surroundings as the displayed image may be faint or dark distorted
3. being a projectile Select location for mounting the monitor in desired location Ensure monitor location will not obstruct your vision while driving A DASHBOARD MOUNTING i Screw and secure the mount stand to the back of the monitor ii Clean dashboard surface where monitor will be mounted iii Remove adhesive protector from underneath of monitor mounting stand iv Place and secure monitor mounting stand onto dashboard using adhesive from tape from bottom of stand v Adjust and tilt mounting to have a better viewing angle B VENT MOUNTING i Slide and lock vent clip to back of monitor as shown ii Adjust to desired view angle by rotating center ring rotate clockwise to unfasten CAUTION These mounting options are illustrations only and may not each apply to every type of vehicle For vehicle specific questions contact your vehicle s manufacturer to be sure that the installation and mounting location you choose will not degrade the safety of any system or device on your vehicle HOW TO POWER THE MONITOR Select and connect monitor power source a BASIC INSTALLATION Power up monitor using 12V adapter provided 1 Plug 12V adapter to vehicle cigarette lighter socket 2 Connect adapter to monitor power input 3 Press monitor s ON OFF button b ADVANCE INSTALLATION Hardwire monitor to vehicle power source 1 REFER to vehicle Owner s Manual before attempting monitor installation to avoid corrupting the comput
4. camera The system is only designed for backup reserving purposes Manufacturer is not responsible for damages on the system or the vehicle if used for other purposes ALWAYS engage Parking Emergency Hand Brakes of the vehicle when testing the system Like most wireless devices the system may cause interference to other wireless devices or vice versa Wireless devices such as WIFI routers Bluetooth devices and mobile handsets may cause interference with the monitor If this happens you will notice rolling lines blurry images or static images on the monitor The system is designed to ADD safety and protection The device was NOT designed to replace other safe driving habits Double checking and looking around before backing up is STILL the safest way SAFETY AROUND AND BEHIND OTHER VEHICLES Using a rear view camera is not enough to completely overcome a vehicle s blind spot Many preventable injuries and deaths occur in driveways or parking lots when drivers do not see children pets or others near their vehicles Here are a few safety tips that will help you to avoid a backover accident Walk completely around your vehicle before getting in Check for kids toys and pets before entering the vehicle and starting the engine Know where children are Have children stand in a place where they are in full view Be aware of young children Young children are small and hard to see Parents caregivers and all adults need
5. eplace the tires the area displayed on the monitor may change and you may need to adjust the camera There is a plastic cover over the camera Do not scratch the cover when cleaning dirt or snow from the cover The camera has a water resistant construction Do not detach disas semble or modify it This may cause incorrect operation Camera is water resistant but not waterproof Do not submerge camera in water which can cause internal damage to the camera If the temperature changes rapidly such as when hot water is poured on the vehicle in cold weather the system may not operate normally When the temperature is extremely high or low the screen may not clearly display objects When strong light directly enters the camera objects may not be displayed clearly The screen may flicker under fluorescent light The colors of objects on the rear view monitor may differ somewhat from those of the actual object If dirt rain or snow attaches to the camera the monitor may not clearly display objects If water droplets snow or mud adhere to the camera lens rinse with water and wipe with a dry cloth Do not use alcohol benzene or thinner to clean the camera This will cause discoloration To clean the camera wipe with a clean cloth dampened with mild cleaner diluted with water and then wipe with a dry cloth Will work up to 30 feet Working distance varies depending on the interference between the monitor and the
6. er system or other vital operating systems in the vehicle Before using the hardwire kit it is highly recommended seeking assistance or professional installation from an automotive electrician WARNING Manufacturer assumes no liability for damage caused to vehicle due improper installation or use 2 Use the monitor s Wiring Harness supplied for this installation 3 Locate a suitable route for the Wiring Harness from the selected monitor mounting location to the vehicle fuse box 4 Disconnect the vehicle s battery 5 ldentify the 12V ACCESSORY terminal in the vehicle s fuse box This terminal only provides power when the vehicle s ignition is turned to the ACCESSORY position 6 Connect Wiring Harness red wire to this terminal 7 Connect Wiring Harness black wire to common ground earth 8 OPTIONAL Extend and connect Wiring Harness blue wire to positive wiring of the reverse light This will serve as an interrupt and will power up the monitor when the car is put in reverse At this point you can check if you properly connected the wires by Reconnecting the battery Turn vehicle ignition to the Accessories position Connect Monitor Wiring Harness to the Monitor Press Monitor On Off button and wait for monitor to turn on If the camera is not yet installed all you will see is noise or static Disconnect vehicle battery before proceeding with installation 9 Identify the 12V wire for the ve
7. from time to time to make sure that it is always focused and adjusted to the desired point of view SCHEMA CAMERA WIRING 12V DC Reverse Lamp O Scotch Lok de 2 Reverse Lamp Scotch Lok1 Ground CAUTION Before connecting camera wires use a Volt Meter or a Multi Meter to determine positive and the negative wires on the vehicle s reverse light wires a Determine positive and negative wires Most vehicles will have two color wires BLACK for negative and RED for positive b Disconnect vehicle battery before proceeding to the next step as a precaution c Using the Scotch Lok Connectors connect camera s RED wire to reverse light s positive wire If needed use pliers to squeeze Scotch Lok and ensure a good connection d Connect camera s BLACK wire to reverse light s negative wire Secure and link wires using the Scotch Lok Connectors e Secure wires with cable ties or electrical tape At this point you can check if you properly connected the wires by Reconnecting the battery Turn the ignition to the Accessories position Engage the Emergency or Hand Brake Put the vehicle in reverse Press On Off button of the Monitor If the camera and the monitor wirings are hooked up correctly the monitor should turn on and should display image of rear view of the vehicle Disconnect vehicle battery before proceeding with installation OPERATIONS SAFE OPERATING POINTS If you r
8. hicle s reverse light s This wire runs from a switch in the vehicle s transmission to the vehicle s reverse light s 10 Attach blue wire from Wiring Harness to the 12V reverse light wires using the supplied Scotch Lok see SCOTCH LOK USAGE 11 Monitor will automatically turn ON when vehicle transmission is placed in reversed and turn OFF when transmission is not in reverse MONITOR OPERATION INSTRUCTION AUDIO VIDEO BRIGHTNESS ROTATE USB slot AV input for recharge only 12V DC Power POWER ON OFF 1 The POWER ON OFF button turns the LCD Monitor On or Off 2 When the monitor was turned on it automatically connected to the Reversing Camera AV Press AV button the monitor will show AV images Rotate Control the rotation of the image Brightness Control the brightness of the Monitor Color Control the color of the monitor USB Slot Recharging only for items that can be recharged via USB such as mobile phone MP3 etc 12V Power Input Supply the power for the monitor AV Input Jack Connect the monitor with AV sources CAMERA INSTALLATION Install Vehicle Backup Camera in the top mounting screw of your vehicle s rear license plate to achieve maximum viewing angle Back Front 1 Unmount license plate from rear of vehicle 2 Locate reverse tail lights and select a wiring route the camera will use for its power source 3 Inspect and determine route of camera wiring to reverse lights 4 Inse
9. ire area behind your vehicle PLOM34 WIR Wireless Back Up Night Vision Camera And Monitor System INSTALLATION AND OPERATION MANUAL COMPONENTS oR i Back Up Camera 3 5 LCD Monitor Power Wire AV Cable 12 Volt Adaptor oo C Cable Ties Mounting Screws Optional Double Sided Paper Paste INSTALLATION INSTRUCTION These installation instructions do not apply to all types of vehicles They are meant only as a general guide due to the large number of vehicle makes and models Consult your local motor vehicle laws on the use of this product to be sure it is permitted WARNING Through installation of the Vehicle Back Up Camera you should be sure not to degrade the safety of any system or device on your vehicle Improper installation and wiring of the Vehicle Back Up Camera system may damage the vehicle s electrical system including vital vehicle computer and operating systems That could lead to an accident or fire causing property damage and or serious personal injury It is highly recommended to seek professional installation advice from a qualified auto electrician or in the alternative to have the installation performed by a qualified auto electrician MONITOR INSTALLATION NOTICE Please ensure that monitor is secured and mounted where it would NOT obstruct any OEM vehicle safety features In an event of an accident manufacturer is not responsible for bodily injury caused by the monitor
10. or not entirely visible Always check behind and all around the vehicle visually and with mirrors before proceeding The area displayed by the Vehicle Back Up Camera is limited Vehicle Back Up Camera does not display objects that are close to or below the bumper underneath the vehicle or objects out of the camera s field of view The area displayed on the screen may vary according to vehicle orientation or road conditions The Vehicle Back Up Camera is not intended for use during longer backing maneuvers or backing into potential crossing traffic or pedestrians Crossing traffic or pedestrians may be approaching outside of the camera s field of view Be sure to check the camera s position and mounting angle before each use Make sure the trunk hatch or backdoor is completely and securely closed when backing up When washing the vehicle with high pressure water be sure not to spray it around the camera Otherwise water may enter the camera unit causing water condensa tion on the lens a malfunction fire or an electric shock Do not strike the camera It is a precision instrument Otherwise it may malfunc tion or cause damage resulting in a fire or an electric shock This product will only provide images of items that are within the field of view of the camera Thus it is imperative that the camera should be kept clean and unobstructed and should properly mounted so that its field of view includes the ent
11. rt camera wires through grommet supplied The grommet protects the wire from the metal edge 5 Check for openings or holes where license plate is mounted to insert camera wires If no opening is available drill a small hole 6 5mm diameter and insert wires see Figure 1 Select a location close to the camera s power cables Figure 1 Note The Vehicle Backup Camera can be installed without drilling a hole by using a pre existing hole on the vehicle to route the wires to the reverse tail lights CAUTION Take extra precaution necessary to avoid vehicle damage Before drilling inspect behind the drilling location to ensure there are no vehicle wirings or components 6 Insert wires into selected drilled opening remove the bulbs as a precaution Figure 2 Figure 2 7 Route wires to selected reverse tail light Ensure wires are not obstructed or tangled 8 Remove light socket from its reverse light housing CAUTION It is highly recommended to remove the bulbs as a precation 9 Connect camera wires 10 Connect bulb back into light socket 11 Reinstall light socket into reverse light housing 12 Slide license plate between camera amp mounting Figure 3 13 Align camera mount to license plate holes PYLE BACKUP CAMERAS Figure 3 License plate Grommets 14 Once camera is secured adjust camera angle to desired point of view Figure 4 Figure 4 Caution Double check the camera angle
Download Pdf Manuals
Related Search