Oracle Dome Installation Guide
Contents
1. The two RJ45 connectors are used for alarms and UTP control The serial connector provides the serial telemetry interface The dome will also be capable of accepting future software upgrades via this serial connection This will ensure the dome can be incorporated into any upgraded network RJ45 connectors Pin Connection 1 Alarm 1 Alarm 2 Alarm 3 Alarm 4 Alarm Ground Not connected Relay A Relay B Note The relay is suitable for switching DC only and is rated at 0 7A co 4004 C0 N Multiway connector The serial connection is not required when using UTC Control Connector Function 24VAC 24VAC from UL2044 approved Class 2 current limited 24VAC 1A 24VAC 24VAC from UL2044 approved Class 2 current limited 24VAC 1A 485A Pin 1 on Serial Connection to appropriate DVR 485B Pin 9 on Serial Connector to appropriate DVR Vid GND BNC Earth screen connection Vid Sig BNC Signal centre pin connection Note Refer to Dome Configuration for a list of appropriate DVRs Dedicated Micros 2008 Mounting Configurations External With appropriate brackets this dome enclosure can be mounted in any of the orientations shown below Note Mounting brackets may have been ordered and delivered separately 2 T EN 5 PR A 4d 4 1 Wall Pendant Mount order code DM 90002 giving pendant or wall mount options 2 Extende2. RS485 CURRENT LOOP TELEMETRY SWITCH LOCATION SW2 Note SW2 should be set towards the centre of the PCB RS485 COAX OR DIFFERENTIAL VIDEO SWITCH LOCATION SW3 Note SW3 should be set towards the centre of the PCB coax RS485 Serial Connection The coax cable and power wires are always connected The RS485 wires are only connected when an RS485 controller is being used The dome supports the DM RS485 PTZ protocols The desired protocol and the node address for the dome are selected by the rotary hex switches red blue and yellow inside the dome These are accessed by removing the outer hemisphere and inner shroud refer to Switch Configuration for more information RS485 protocol allows multiple domes to be connected via the serial connection on the back of the DVR Each dome in the chain should have a unique individual address to enable it to be called by the DVR The switch settings for the protocols and node addresses are shown in the table below Dedicated Micros 2008 Address chart Yellow Blue a E ss ss se sr ss eo 70 To configure the Dome using DM RS485 1 Select DM RS485 by setting the red switch to position 2 2 Select a node address for the dome to be configured Scan across the table to identify the values for the blue and yellow switches blue switch setting is shown on the left yellow switch setting on the right For example if the dome is to be used with node address ID 5 the
3. The dome receives power and data and sends video and data via the multiway connector This feeds into the PCB housed in the terminal box which provides wiring breakout and inter connectivity Note The terminal box is not supplied in the USA Dome connector Note Viewed from wiring side The 15 core cable connections are as follows Cable Function Connector Pin Green Yellow Earth F Green Yellow Earth G Coax Video Signal C Coax Vid Screen P Yellow RS485A E Green RS485B T Brown 24VAC D Blue 24VAC U Violet Alarm 1 H Pink Alarm 2 S Grey Alarm 3 J Orange Alarm 4 R Black Alarm Ground K White Relay A N Red Relay B L Dedicated Micros 2008 Future DVR RS485 Telemetry Optional Alarm Relay Inputs DVR Video To Dome Output Multiway Connector O Minimum configuration The simplest connection possible to the Oracle Dome would require the following The Mains supply live earth and neutral is connected to the heavy duty connector block mounted in the Power Supply Unit next to the PCB Power select links J1 8 J2 should be set to 24VAC centre and arrowed pin bridged as shown above Telemetry termination TEL TERM link is normally not fitted as shown above Function Colour PCB Connector Safety Earth Green Yellow Shield Gnd Power Brown PWR Power Blue PWR Video Coax BNC RS485A Yellow Tx Rx A RS485B Green Tx Rx B Note Whilst the Alarm and Relay inputs are not essential for minimum
4. ceiling void Selection of this suitable point should consider that it will receive the full force of the dome should it be dropped For wall pendant amp snowdrop mounted domes 1 Clip safety bond to the mounting bracket eyelet on flange of bracket to secure For standard ceiling mounted domes attach the supplied safety bond EM 1 Attach bond to a suitable secure position in the ceiling void Note Always support dome with bond prior to mating connector The weight of dome should be supported by bond ensuring no stress is placed on centre connector at any time Dedicated Micros 2008 Dome Mounting Pendant Mount F A Secure and hang dome to bracket by attaching safety bond spring clip to eyelet B Lift dome to bracket flange ensuring head of screws previously fitted Cap head Screw pass through keyhole slots Twist to locate C Mate the previously prepared central connector refer to Electrical Connections for more information supplying power amp control to dome ensure power is off when connecting D Tighten 4 top mounting fixings with Hexagonal key supplied to secure E Secure any plastic covers or trim wall pendant installations only Dedicated Micros 2008 Tile Mount E 190mm umm 3 x 26mm 204mm PCD Dp A Remove the selected tile that will have the dome mounted in it Use the mounting ring B as a template to mark the drilling positions of the 3 x supporting holes on a 2
5. gt DEDICATED mMiICROS Oracle Dome Camera Installation Manual www dedicatedmicros com Contents INTRODUCTION coca e edente 3 Components supplied External 5 Components supplied Internal 6 Electrical Connections External 7 Electrical Connections Internal 9 Mounting Configurations External 10 Mounting Configurations Internal 13 Control Configuration All Models 17 Upgrading Dome Software 22 Dome Configuration sssssssssss 24 Troubleshooting sees 25 EN hoc n ia 26 Whilst every attempt is made to ensure these manuals are accurate and current Dedicated Micros reserve the right to alter or modify the specification of the machine described herein without prejudice Dedicated Micros 2008 TUT NEN Rd t Introduction Congratulations on choosing a Dedicated Micros Oracle dome camera This manual will provide all the necessary information to install the Dedicated Micros Oracle Dome Camera RF Interference warning This is a class A product In a domestic environment this product may cause radio frequency interference in which case the user may be required to take adequate measures J Product Safety id WARNING 4 Installation and servicing is only to be carrie
6. 04mm pitch circle diameter 6mm4 holes if using the supplied cavity plugs A and the 190mm hole for the dome Fit the cavity plugs A to the holes Note The installer is responsible for ensuring the fixings used to mount the dome are suitable for the material and will adequately support the weight of the dome B Attach the mounting ring to the dome using the provided 6 x M3x8 fixings C C Re install the tile in the ceiling Secure and hang dome to a suitable mounting point in the ceiling void by attaching safety bond spring clip to eyelet through the large centre hole in the tile Note Ceiling installation is made easier by removing an adjacent ceiling tile during installation D Fasten the dome to the mounting ring B using the provided 3 x No 8x1 25 4mm self tapping screws D or suitable fixings provided by the installer E Snap fit the provided tile mount bezel E This replaces the standard bezel F provided with the camera Discard the standard bezel F Dedicated Micros 2008 Control Configuration All Models Switch settings Different controllers require different protocols and a red rotary switch is provided to select the desired protocol These are accessed by removing the outer hemisphere refer to Switch Configuration for more information There are three color coded switches red blue and yellow which are all located inside the dome camera housing The blue and yellow switches have differen
7. Note The serial connection is not required when using Up The Coax control Up the Coax Switch Settings Switch Setting Red 4 Yellow Blue Not required RED SWITCH LOCATION BLUE SWITCH LOCATION YELLOW SWITCH LOCATION Dedicated Micros 2008 Upgrading Dome Software The Oracle dome has an expanded feature and control set over other domes which are only available through the Dedicated Micros PTZ protocol These features are accessed through a set of web pages available on the latest Dedicated Micros machines DV IP Server DV IP RT DV IP HD and HighVu Excel and that will have access to this dome These pages will be available through the familiar unit interface and will allow easy configuration of the domes features To upgrade dome software via RS485 Note The dome must be configured to RS485 telemetry to perform the software upgrade Red Switch to position 2 Software is downloaded via the RS485 telemetry link on the dome using a USB to RS485 converter on the PC 1 Download the software domecfg and the application upgrade software from the Dedicated Micros website 2 Connect a USB to 485 converter to a USB port on your PC see note below for details of pin out for 9way Dtype connector 3 Connect the RS485 serial lead from the Oracle dome to the output of the USB to 485 converter 4 Launch the Domecfg application 5 Select Setup tab top left of window in ComPorts window select drop down
8. ard ceiling mounted domes attach the supplied safety bond For wall pendant amp snowdrop mounted domes For wall pendant amp snowdrop mounted domes Function Dependant on Red Switch Configuration Function Dependant on Red Switch Configuration Function Protocol Selection List of DVR s required to utilise advanced programming features Minimum configuration Mounting Configurations External Mounting Configurations Internal Multiway Connector A O AS cena weave ave ere cede mea Multiway connector No picture No telemetry control Notes PCB Pendant Mount Picture with intermittent control E PROGU GCE Salt yc iac teta ete e AA ARES AA RED SWITCH LOCATION RED SWITCH LOCATION RE Iherference Wann tia IS ote tete tete dota i imt eed RJ45 connectors RS485 CURRENT LOOP TELEMETRY SWITCH LOCATION SW2 RS485 Serial Connection Switch Configuration Switch settings TERMINATION SWITCH LOCATION SW1 Tile Mount To configure ihe Dome using DM RS485 cercasi ete reb ret x rag uc se tias To upgrade dome software via RS485 Troubleshooting Up The Coax PTZ control Upgrading Dome Software Up the Coax Switch Settings YELLOW SWITCH LOCATION YELLOW SWITCH LOCATION Dedicated Micros 2008 Dedicated Micros Ltd 1200 Daresbury Park Daresbury Cheshire WA4 4HS UK Dedicated Micros Europe Neckarstrafle 15 41836 H ckelhoven Germany Dedicated Micros France 9 13 rue du Moulinet 75013 Pari
9. ation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna d Increase the separation between the equipment and receiver b Connect the equipment into an outlet on a different circuit different to the receiver Consult the dealer or an experienced radio TV technician for help Modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment under FCC rules Dedicated Micros 2008 Camera Care In order to avoid damaging your camera note the following points CAUTION Remove all packaging inserts and the protective film from the dome cover before using the camera This installation should be made by a qualified service person and should conform to all local codes CE NOTICE EUROPEAN UNION Marking by the symbol CE indicates compliance of this DM product to the Electromagnetic Compatibility Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC of the European Union Such marking is indicative that this system meets the following technical standards EN 61000 6 3 EMC Standard Residential Commercial and Light Industry EN 61000 3 3 Limitations of voltage changes fluctuations and flicker in public low voltage supply systems for equip
10. configuration it is recommended that they are connected to the PCB in case they are required in the future Note The Multiway cable should be securely clamped to the chassis using the screw clamp provided The insulation should be stripped back to allow the clamp to contact the cable foil sheath All glands into the PSU should be securely tightened to prevent the ingress of moisture Connecting the DVR to the Oracle Dome via PCB Video to the DVR is sent via the BNC Video Control Output connection shown above Telemetry control is via the DVR RS485 Telemetry Inputs Outputs connection shown above RS485A connects to Pin 1 on the serial connector of the DVR RS485B connects to Pin 9 on the serial connector of the DVR Alternatively the Oracle supports either up the coax UTC control via the video output BNC connector or un shielded twisted pair UTP via the UTP video UTP net connectors available via future software upgrade Dedicated Micros 2008 Electrical Connections Internal The dome requires connection to the power supply and to the BNC connection of the DVR Use the serial port connection if serial telemetry is required There is no prepared cable included the connector for the camera is included Reserved for UTP Ethernet versions BNC 24VAC 24VAC Pin 1 Alarm 1 l l Pin 2 Alarm 2 Pin 3 Alarm 3 24V Power Pin 4 Alarm 4 Supply Pin 5 Alarm Ground Pin6 NC Pin 7 Relay A Pin 8 Relay B
11. d Wall Mount order code DM 90009 for more flexibility in wall mounting 3 Corner Bracket order code DM 90007 for mounting to corners of buildings in conjunction with DM 90002 4 Snowdrop mount bracket order code DM 90004 for mounting at the top of a pole or column 5 Pendant Mount order code DM 90003 250mm order code DM 90012 500mm order code DM 90013 1000mm order code DM 90014 1500mm for roof or parapet mounting Dedicated Micros 2008 Safety Bond The safety bond is designed to prevent damage to the dome if it is dropped during installation or maintenance It should be connected between the mounting point on the dome and a suitable secure position either on the bracket or within the ceiling void Selection of this suitable point should consider that it will receive the full force of the dome should it be dropped For wall pendant amp snowdrop mounted domes 1 Clip safety bond to the mounting bracket eyelet on flange of bracket to secure For standard ceiling mounted domes attach the supplied safety bond 1 Attach bond to a suitable secure position in the ceiling void Always support dome with bond prior to mating connector The weight of dome should be Note supported by bond ensuring no stress is placed on centre connector at any time Dedicated Micros 2008 Dome Mounting A Secure amp hang dome to bracket by attaching safety bond spring clip to eyelet Note Procedure is the same for all i
12. d out by suitably qualified and experienced personnel and should conform to all local codes E Only power low voltage cameras from the provided power supply Use only a Class 2 power supply with a maximum current of 1 5 amps and the wiring as specified in the National Electrical Code ANSI NFPA 70 This camera range is designed for use in general purpose CCTV applications and has no other e purpose Only operate your camera between the temperatures of 10 C and 40 C This low voltage camera must be powered with either a 12V DC or a 24V AC power supply Do not operate your camera outside its specified power supply range FCC CLASS B REGULATORY NOTICE This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular install
13. e information Picture with intermittent control Cause This is most likely due to too much or too little video gain whilst using UTC telemetry Solution Adjust using the Oracle dome settings page on the DVR Dome spins continuously DM controllers Cause No joystick dead band recognized as joystick was off centre during power up Solution Reboot the controller with the joystick self centred No telemetry control Cause Check the telemetry and address switch settings Note Any changes to the switch settings are briefly displayed on the video output from the dome as confirmation Dedicated Micros 2008 26 EN RA AI A Notes Dedicated Micros 2008 Index Address chal ss ctii testet temer ono ica liar np tdet granada BLUE SWITCH LOCATION Camera Care CE NOTICE EUROPEAN UNION COAX OR DIFFERENTIAL VIDEO SWITCH LOCATION SW3 Components supplied External Components supplied Internal Connecting the DVR to the Oracle Dome via PCB Control Configuration All Models Dome Configuration cocinan ET Dome connector Dome Mounting Dome Mounting Dome spins continuously DM controllers Electrical Connections External Electrical Connections Internal FCC CLASS B REGULATORY NOTICE For standard ceiling mounted domes attach the supplied safety bond For stand
14. ment with rated current up to 16A EN 61000 3 2 Limits for harmonic current emissions for equipment with rated current up to 16A EN 50130 4 Immunity requirements for components of fire intruder and social alarm systems EN 60950 Safety of IT and related equipment EN 55022 Class B Radiated Emissions Standard suitable for Commercial or Residential use EN 60825 1 Safety standard for LED s and Lasers Further details about these applicable standards can be obtained from Dedicated Micros Ltd 1200 Daresbury Park Daresbury Cheshire WA44HS A Declaration of Conformity with all relevant European Union Directives has been made is on file and is available from the Dedicated Micros address above Em CC This product is marked with the CE symbol and indicates compliance with all applicable directives Directive 89 336 EEC A Declaration of Conformity is held at Dedicated Micros Ltd 1200 Daresbury Park Daresbury Cheshire WA44HS Dedicated Micros 2008 Components supplied External Before installing the dome please remove the components from the packaging and verify that all items listed below have been supplied 1 x Dedicated Micros Oracle Dome enclosure and camera with incorporated safety bond 1 x Oracle Dome Power Supply except USA 1 x Dedicated Micros Oracle Dome manual Note for US Customers The PSU must be a UL2044 approved Class 2 current limited 24VAC Power Supply with a maximum current
15. menu and select the PC COM port that has been assigned to the USB to RS485 converter T Ensure the following settings are selected Baud rates 9600 Parity None Data bits 8 Stop bits 1 Flow control Xon char 17 Xoff char 19 EE 8 Select OK 9 Select the Camera number Cam box top left window to ensure the upgrade program addresses the packets to the relevant dome 10 Confirm that correct COM port has been selected by using the Up U Down D Left L and Right R buttons to move the dome If settings are correct the dome should move when requested If not check The camera number equates to the dome address switch settings and that the USB to RS485 converter is correctly configured 11 Select File gt Open and navigate to the downloaded application upgrade software zip file Left click the file and then press Open 12 Select Upload to transfer the file to the dome Upgrade takes approximately twenty minutes the progress can be monitored using the Domecfg application or 3 by viewing the camera that is being upgraded via the unit it is connected to Y Important The dome must not be powered down whilst a software download is in progress Powering down the dome could permanently corrupt the dome software 13 When the upgrade is complete the Domecfg application will display Finished 14 Disconnect the RS485 telemetry cable from the USB to 485 converter and reconnect to the serial po
16. nstallations Note Ceiling installation is made easier by removing an adjacent ceiling tile during installation B Lift dome to bracket flange ensuring head of screws previously fitted cap head screw pass through keyhole slots Twist to locate C Mate the previously prepared central connector refer to Electrical Connections for more information supplying power amp control to dome ensure power is off when connecting D Tighten 4 top mounting fixings with Hexagonal key supplied to secure E Secure any plastic covers or trim wall pendant installations only Dedicated Micros 2008 Mounting Configurations Internal With appropriate brackets this dome enclosure can be mounted in any of the orientations shown below Note Mounting brackets may have been ordered and delivered separately 1i Wall Pendant Mount order code DM 90002 giving pendant or wall mount options 2 Corner Bracket order code DM 90007 for mounting to corners of buildings in conjunction with DM 90002 3 Tile mount order code DM CSD TMR for suspended ceilings 4 Snowdrop mount bracket order code DM 90004 for mounting at the top of a pole or column Dedicated Micros 2008 Safety Bond The safety bond is designed to prevent damage to the dome if it is dropped during installation or maintenance It should be connected between the mounting point on the dome and a suitable secure position either on the bracket or within the
17. of 1 5 amps and the wiring as specified in the National Electrical Code ANSI NFPA 70 Note Mounting brackets may have been ordered and delivered separately Important The Advanced Programming and Control features on the Oracle Dome are only i available when used with the latest Dedicated micros DVRs These include DV IP Server DV IP HD DV IP RT and HighVu Excel Standard functionality will still be available with other control equipment Dedicated Micros 2008 Components supplied Internal Before installing the dome please remove the components from the packaging and verify that all items listed below have been supplied 1 x Dedicated Micros Oracle Dome enclosure and camera with incorporated safety bond 1 x Dedicated Micros Oracle Dome manual Note The PSU must be a UL2044 approved Class 2 current limited 24VAC Power Supply with a minimum current of 1 5 amps and the wiring as specified in the National Electrical Code ANSI NFPA 70 Dedicated Micros recommends the DM 94012 for indoor dome Note Mounting brackets may have been ordered and delivered separately Important The Advanced Programming and Control features on the Oracle Dome are only available when used with the latest Dedicated micros DVRs These include DV IP Server DV IP HD DV IP RT and HighVu Excel Standard functionality will still be available with other control equipment Dedicated Micros 2008 Electrical Connections External Multiway Connector
18. rt of the DVR 15 Confirm correct operation using telemetry control of the DVR Dedicated Micros 2008 Note Pin out for 9 way D type connector to the DVR is normally Pin 1 for RS485 A and pin 9 for RS485B If the converter used is different then an intermediate cable may be needed to transpose the wires see converter s documentation for pin out details 16 Confirm the upgrade has been successful by checking the software version number on the startup screen This screen can also be displayed by special preset G4 Dedicated Micros 2008 Dome Configuration The Dome is configured via the attached DVR The special software features are available via the interface on DVR s capable of accessing them DV IP Server DV IP RT DV IP HD and HighVu Excel refer to the documentation for your individual DVR for further details The Dome has advanced features that include Point and Go Privacy masking Presets Sectors and Patrols along with Camera and Event settings Some of these will be available to standard DVR s List of DVR s required to utilise advanced programming features DV IP Server DV IP HD DV IP RT and HighVu Excel running Gen3 pages Note Standard functionality will still be available with all other control equipment X Dedicated Micros 2008 EA aig Troubleshooting No picture Cause 1 Check the Input voltage 2 Check the continuity on the dome cable refer to Electrical Connections for mor
19. s France Dedicated Micros Slovenia Delavska cesta 26 4208 Sencure Slovenia Dedicated Micros Benelux Joseph Chantraineplantsoen 1 3070 Kortenberg Belgium Dedicated Micros USA 14434 Albemarle Point Place Suite 100 Chantilly Virginia 20151 USA Dedicated Micros Australia PTY 5 3 Packard Avenue Castle Hill NSW 2154 Australia Dedicated Micros Asia PTY 16 New Industrial Road 03 03 Hudson Techno Centre Singapore 536204 Dedicated Micros Middle East Building 12 Suite 302 P O Box 500291 Dubai Internet City Dubai United Arab Emirates Dedicated Micros Malta Ltd BLB017 Bulebel Industrial Estate Zejtun ZTNO8 Malta Installed by
20. switches should be set to 05 i e the blue switch should be set to 0 and the yellow switch set to 5 3 Set the individual RS485 address for the dome on the blue and yellow switches fitted inside the dome housing The dome will display its protocol and address setting when first powered on as the screen will show in the example above Node Address 05 It will also display briefly after each time the setting is changed All Dedicated Micros Oracle domes are fitted with a termination switch SW1 shown above If a single dome is connected on the RS485 line or if a star configuration is used the termination switch should be switched to ON Switch towards the centre of the PCB dt If multiple domes are connected in a daisy chain configuration then only the last dome in the chain should be switched to IN All other domes in the chain should be switched to OFF Switch set away from the centre of the PCB Dedicated Micros 2008 Up The Coax PTZ control Note Only basic PTZ and preset functionality is available currently using UTC control For full programming and control including point amp go and Absolute Positioning use RS485 control Commands to control the position of the dome can be transmitted up the same co ax cable used to transmit the video signal to the recorder station Individual addresses do not need to be configured within the dome because the instruction is sent directly to the dome
21. t functions depending on the protocol selected by the red switch Switch Configuration To access the address switches and termination switch remove the outer hemisphere by unscrewing the six hemisphere securing screws The location of the switches is shown Access to the switches is improved if the inner shroud is removed by taking out the four securing screws This operation should be carried out in an office type environment to avoid ingress of moist air RED SWITCH LOCATION Function Protocol Selection Position Protocol 0 Auto Sense under development 1 DM UTC under development 2 DM RS485 3 DM Current Loop under development 4 BBV UTC E Note The selected protocol will be displayed on screen at power up for a few seconds each time the rotary switches are changed Dedicated Micros 2008 17 BLUE SWITCH LOCATION Function Dependant on Red Switch Configuration UTC Current Loop Not Used Serial Referenced by Camera Number on the DVR refer to Address chart in section RS485 Serial Connection YELLOW SWITCH LOCATION Function Dependant on Red Switch Configuration UTC Current Loop Not Used Serial Referenced by Camera Number on the DVR refer to Address chart in section RS485 Serial Connection Note SW1 should be set towards the centre of PCB to turn RS485 termination ON or set away from the centre of the PCB to turn RS485 termination OFF Dedicated Micros 2008
Download Pdf Manuals
Related Search