Home

Manual

1. Figure 5 8 PTZ Configuration page Cator Ged Demo Arias jp and This moves the viewable area within the active CCD region From the center it can be moved two click positions in the the positive negative x y ae direction Direction Key O This button moves origin point When push Tele button camera go Zooms In Tele Wide When push Wide button camera go Zooms Out Es a Near F When push Near button camera go Focus In ear Far When push Far button camera go Focus Out When push Iris button camera go to close the IRIS Iris Iris P 3 When push Iris button camera go to open the IRIS Saves the current position to the values in the Preset Edit box del Deletes the current position to the values in the Preset Edit box Moves the PTZ to the defined Preset position Start to save for Pattern Pattern End to save for Pattern Runs Pattern En o Runs defined Group Menu On Displays camera OSD menu in screen Menu Off Displays off for camera OSD menu E LA gt Move or change a OSD item in OSD menu Set Near set selected menu function Back Far cancel and move to selected menu function Pan Speed Select the Pan Speed of PTZ Moving Speed Setup Tilt Speed Select the Tile Speed of PTZ Set Applies and Saves selected Pan Tilt s Speed Cator Ged Dime Arias jp and 5 IP network Part Maintaining Server Configurations This page configures system parameter
2. MASK NO e DISPLAY CLEAR MASK 1 8 Select Mask number If the selected mask has already data camera moves as it was set Otherwise UNDEFINED will be displayed under MASK NO ON OFF Sets if camera makes mask shows or not on images CANCEL OK Deletes data in the selected mask NO Move camera to the area to mask Then the menu to adjust mask size will be displayed Adjust mask size Use Direction KEY or arrow buttons to adjust mask size lt gt Left Right AV Up Down Adjusts mask width Adjusts mask height Cor Head Demo Hates jp and 4 OSD Menu Camera Setup Model ISS2765N P 00M CAMERA SETUP FOCUS MODE SEMIAUTO MAX ZOOM x2f0 FLICKERLESS OFF COLOR ON e FOCUS MODE LINE LUCK OFF WHITE BALANCE SETUP AUTO EXPOSURE SETUP MAX ZOOM BACK EXIT MENO OFF e FLICKERLESS e COLOR e LINE LOCK MB WHITE BALANCE SETUP WB MODE WB SETUP GLOBAL TUB MODE AUTO RED ADJUST BLUE ADJUST ae e RED ADJUST e BLUE ADJUST BACK EXIT MENU OFF Setup the general functions of 27x optical zoom camera module AUTO MANUAL SEMIAUTO Sets camera focus mode xl x270 Sets the maximum zoom magnification ON OFF When an NTSC camera if used under 50Hz and PAL under 60Hz flickering may appear on the screen When this happens turn FLICKERLESS setting ON This prevents flickering which happens when the frequency of the
3. MOVE TO TARGET POSITION NEAR SAVE FAR CANCEL DIT PRESET LABEL D Edits label to show on monitor when camera arrives at presets EDIT LABEL PRESET 1 In Edit label menu a reverse rectangular is cursor B As soon as finishing selecting alphabet cursor moves to the next digit 11234567890 OK E ABCDEFGHI J CANCEL KLMNOPORST UVIWXYZabcd efghijk mn oparstuuux Current Cursor Position yZ Using Left Right Up Down of Direction KEY move to an appropriate character from the Character set To choose that character press the NEAR key 1234567890 ABC DEFGH IJ KLMNOPQRST UVWXYZabcd efghijk mn opqrstuv wx yz lt gt lt Back Space Char Space Char If you want to use blank choose Space character If you want To delete a character before use back space character lt 3 If you complete the Label editing move cursor to OK and press NEAR key to save completed label To abort current change move cursor to Cancel and press NEAR key Mm EDIT RELAY OUT RELAY OUT N ON OFF RELAY OUT PRESET 1 Sets relay output when changing preset position RELAY OUT 1 OFF RELAY OUT OFF The uppercase N indicates the number for the preset BACK EXIT MENU OFF Cutdeor Head Demo Arias jp and 4 OSD Menu Swing Setup SWING NO SWING SETUP SWING NO 1 IST POS NOT USED 2ND POS NOT USED 1ST POS SWING SPEE
4. Recalls previously saved configurations Caor Joel Dame Dries jp anet 5 IP network Part Configuring FTP This configures How the Alarm Images get sent out using FTP once event occurred in the XPEED XNET system Click gt FTP button to open the page shown in Figure 5 21 CNB Network Camera Setup Pagel Windows Internet Explorer Ge E no 192 168 123 100 htm1 view index html stamp 1 258596871765 File Edit rien Favorites Tools Help H ve de CNB Network Camera System Setup Status FTP Server Users FTP Name Date amp Time FTP Port 21 Multi Viewer 1 65535 PTZ Configuration Maintain Server Login Information System Log User Name Password Audio amp Video Audio RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FIP A 100 a Figure 5 21 FTP Page Cor Ged Demo Bates jp and Enter the address of the FTP server to send Alarm Images to in the event processing FTP FTP Name The client PC at that IP address has to run the FTP server in order to receive the Alarm Server Images FTP Port Enter the port number for the FTP server to send Alarm Images to in the event processing Login User Name Enter the user name of the FTP server to send Alarm Images to in the event processing Information Enter the password of the FTP server to send
5. e Privacy Zone Mask Global Local Image Setup e SemiAuto Focus This function enables to resume the last action executed before power down Most of actions such as Preset Pattern Swing and Group are available fort his function but Jog actions are not available to resume In case that tilt angle arrives at the top of tilt orbit 90 the zoom module camera pans180 to keep tracing targets If this function is set to OFF tilt movement range is 0 95 This function enables to locate the camera to specific position automatically if operator doesn t operate the controller for a while The park Time can be defined as an interval from 1 minute to 4 hours 4 Alarm Inputs and 2 Alarm Outputs Relay output are used If an external sensor is activated camera can be set to move to corresponding preset position Also the output relay can be matched to some specific preset positions to do counteractions such as turning on the light or sounding the alarm It is noted that the latest alarm input is effective if multiple sensors are activated To protect privacy Max 8 Privacy Masks can be created on the arbitrary position to hide objects such as windows shops or private house With Spherical Coordinates system powerful Privacy Zone Mask function is possible This function is only available with ISS2465N P X ISS2665N P X ISS2965N P X and ISS2765N P Option WB White Balance and AE Auto Exposure can be set up independently for eac
6. sec Pan Tilt Preset Setting 127 presets label setting individual video setting Swing Setting 8 swings Pattern Setting 4 pattern 1200 commands pattern 5 min Group Setting 8 groups 20 actions group Other Functions Auto Flip Auto Parking Power Up Action Compression SMJPEG MPEG4 H 264 Resolution D1 CIF Video Streaming MJPEG MPEGA or H 264 dual mode Audio Two way full duplex ADPCM G 726 Network Frame rate Dual Mode MJPEG 15fps MPEG4 H264 25fps Protocol IPv4 HTTP TCP RTSP RTP RTCP UDP DHCP UpnP ARP DNS DynDNS Bonjour Connected count at a time Camera live viewer for up to 10 clients Supported DDNS 1 CNB DDNS 2 DynDNS org 3 Reference code with SDK Network Security IP Filtering Privacy Zone 8 Zones Alarm I O 4 inputs 2 outputs OSD Menu On Off Input Voltage 24VAC 19VAC 29VAC Input Power 48VA General Fuse 2A Dome 2 149 Dimension Housing 2 209 7 x 247 2 H mm without Sun Sheild Weight Approx 3 8kg without Sun Sheild 4 3kg with Sun Sheild Operational Temperature 30 C 50 C E Types by installation Wall Mount Sun Shield Quidoor Heet Dome Dries jp and 6 Specifications O Dimensional Drawings MAIN Body without Sun Sheild Weight Approx 3 8kg Pandant Mount Bracket Weight Approx 1 9kg 1 1 2 NPT Wall Mount Bracket Weight Approx 1 2kg 165 0 107 3 175 4 MAIN Body without Sun Sheild Weight Approx 4 3kg un
7. Go v E http 192 168 123 100 html view index html stamp 1258596671 765 File Edit View Favorites Tools Help Y we CNB Network Camera po CNS RTP over TCP w Main Stream MPEG4 H 264 MJPEG Sub Stream MJPEG Note UDP can cause a network overload in a network with low bandwidth poor performance Therefore we recommend to use UDP in local networks or high bandwidth networks only ult Figure 5 2 Web Viewer Page Cor Head Domo Hates jp and oo swa o Captures the still image and displays on a pop up window Capture Save to c WxNetCapture Opens up Basic Setup page Setting Setup page for each IP XNET feature can be opened from this Menu screen Please refer to 5 4 5 21 for detail Opens up PTZ page This page can set up PTZ of network camera and control of PTZ movement Please refer to 5 22 for detail Opens up Motion Detection page You can add or delete area for detecting motion in this page Please refer to 5 23 for detail Opens up Index View page Index View page will display Video as well as setting up Stream Protocol TCP UDP and Codec when using dual Stream A Stream Protocol can be selected when selecting Edit Box Stream Protocol RTP over TCP RTP over UDP When this box is checked Main Stream Video is displayed Main Stream MPEG4 H 264 MJPEG Dual Stream Service When this box is checked Sub Stream Video is displayed Dual Codec needs to be enabled in Vide
8. Enable audio Enable lt Default Disable gt Select audio input source between Microphone and line lt Default Microphone gt SA Microphone input can be used when users send their voice over XPEED XNET system Line input takes the input from an audio device to send over XNET Audio sent to XNET can be played at a Client s PC or an audio device Selects audio input Encoding method lt Default G726 gt Encoding G726 and PCM can be selected Reset Recalls previously saved configurations Cor Head Demo Arias jp and 5 IP network Part Configuring Video XPEED XNET s video features can be configured in this page Click gt Video button to open the page shown in Figure 5 12 CNB Network Camera Setup Page Windows Internet Explorer mak Ge E htp 192 168 123 100 html view index html stamp 1258598871785 Pl File Edit View Favorites Tools Help ww CNB Network Camera CNS System Setup Status Users Date amp Time Multi Viewer PTZ Configuration Maintain Server System Log Audio amp Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP Main Stream Resolution Di Codec H 254 w C Enable Dual Codec Frame Rate Control Frame rate 30 v fps C RTCP Callback Control MJPEG Appearance Quality BL MPE
9. This configures HTTP port to access XPEED XNET s webpage Click gt HTTP button to open the page shown in Figure 5 16 CNB Network Camera Setup Page Windows Internet Explorer ld X ive Searc e Ge E htp 192 168 123 100 htmi view index html stamp 1258596871 765 view Favorites Tools Help w we CNB Network Camera CNB System Setup Status HTTP Users HTTP Port Date amp Time Multi Viewer PTZ Configuration m Me MIDE 1 65535 Maintain Server System Log Audio 8 Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP Figure 5 16 HTTP Page 100 Cator Ged Demo Arias jp and me ee em Enter HTTP Port to access the webpage Default port is 80 and any other port number has to be entered at the end of the ip address HTTP HTTP port when accessing Ex When using HTTP Port 8080 enter http 192 168 123 100 8080 Applies and saves changes Recalls previously saved configurations Cator Ged Dime Arias jp and 5 IP network Part Configuring UPnP DynDNS Bonjour UPnP is a protocol for IP installer software You can enable or disable this UPnP and you can also use a Friendly Name DynDNS configures XPEED XNET s DDNS server information Click gt UPnP DynDNS to open the page shown in Figure 5 17 CNB Network Camera Se
10. e SHUTTER SPEED 0 27 It can be set when AE is in SHUTTTER SPEED mode or in MANUAL mode As for setting value refer to the table below Note BRIGHTNESS 0 96 It can be set when AE is not in MANUAL mode Backlight Compensation a Low weight at the center of the screen g High weight at the center of the screen u Low weight at the left of the screen ce High weight at the left of the screen Low weight at the upper of the screen High weight at the upper of the screen Low weight at the lower of the screen High weight at the lower of the screen Low weight at the right of the screen High weight at the right of the screen Shutter Speed Table The values are based on NTSC type models o a ue o a reo pr Jos mon ro ENE o CTO ET E 1 300 sec 1 800 sec 1 1800 sec 1 6000 sec 6 1 350 sec 1 900 sec 1 2000 sec 1 10000 sec Cor Head Demo Hates jp and 4 OSD Menu Camera Setup ISS2965N P X Setup the general functions of 36x optical zoom modules 00M CAMERA SETUP FFOCUS MODE SEMIAUTO e FOCUS MODE AUTO MANUAL SEMIAUTO DIGITAL ZOOM ON FL ICKERLESS OFF Sets camera focus mode COLOR ON LINE LOCK UFF WHITE BALANCE SETUP DIGITAL ZOOM ON OFF AUTO EXPOSURE SETUP BACK EXIT MENU OFF Sets digital zoom on or off e FLICKERLESS ON OFF When an NTSC camera is used under 50Hz or PAL under 60Hz flickering may appear on the screen When this happens turn Flickerlees setting ON This prevent
11. 22 Preset 22 Swing 22 Pattern 23 Group 23 Other Functions 24 4 OSD Menu OSD Display of Main Screen 25 General Rules of key Operation for Menu 26 Main Menu 26 Display Setup 26 Privacy Zone Mask Setup 27 Camera Setup 27x ISS2765N P models 28 Camera Setup 36x ISS2965N P X EXview Models 30 Motion Setup 32 Preset Setup 33 Swing Setup 35 Patten Setup 36 Group Setup 37 System Initialize 39 5 IP Network Part System Administration 40 Operating The Camera 41 Live View 43 Status Window 45 Configuring Users 47 Setting Date amp Time 49 Configuring Multi Viewer 51 Configuring PTZ 53 Maintaining Server 55 Generating Log Report 57 Configuring Audio 59 Configuring Video 61 Cation Ged Demo Prid jp and Configuring RTP RTSP 63 Configuring the Network TCP IP parameter 65 Configuring IP Filtering 67 Configuring HTTP 69 Configuring UPnP DynDNS Bonjour 71 Configuring CMS 73 Configuring Event Type 75 SMTP Setup 77 ConfiguringFTP 79 Configuring and operating PTZ 81 Configuring Motion Detection Area 83 Configuring Multi view Option 85 6 Specifications 27x ISS2765N P Models 87 36x ISS2965N P X EXview Models 88 Dimensional Drawings 89 7 System Models and Related Accessories System Model Numbers 91 Related Accessories IIS Cator Ged Demo Arias jp and 1 Introduction Features B Camera Specifications e Image Pick up Device 1 4 Interline Transfer CCD e
12. 9 TACT Switch DIP Switch 7 Cabling Mold Line Terminal Block Lockup Screw Drop Prevention Sping lt Main Body gt lt Mounting Bracket gt Do not detach protection vinyl from dome cover before finishing all installation process to protect dome cover from scratches or dust Sets up camera ID and protocol Enables signals and power to come and go between main body and mount bracket This part keeps the camera from dropping during installation and maintenance After install the Bracket please hang the spring to the drop prevention hook of main body as shown in picture for further tasks After assembling main body to bracket screw main body to bracket to protect them from separation by vibration and so on If the fuse is burnt to protect your came from over current damage the fuse have to be replace with new one The fuse specification is 250V 2A however we recommend consulting with supplier to remove the cause of over current During installation Power Video Communication Alarm I O cables are connected on to this cables terminal block Mark to assemble main body to bracket Network Board Factory reset Cator Ged Demo Arias jp and 2 Installation DIP Switch Setup Ml Before installing the camera you should set the DIP switches to configure the camera ID communication protocol Do not use the system upgrade terminal TO BRACKET T B HI 0 Normal Open OPTIONS B
13. Alarm Images to in the event processing NE Applies and saves changes Recalls previously saved configurations Cator Ged Dime Arias jp and 5 IP network Part Configuring and operating Network PTZ This controls XPEED XNET s Speeddome PTZ Click PTZ button in Operator mode to open the page shown in Figure 5 22 CNB Network Camera Windows Internet Explorer Sele Go hitp 192 168 123 100 html view index html stamp 1258596871 765 4 2 Live Search File Edit View Favorites Tools Help w k CNB Network Camera i fe gt Bl abe ly amp 100 Figure 5 22 PTZ page Outdoor Head Demo Arias jp and Sub Field a direction Direction Key Tele Wide When push Near Far When push When push Iris Iris When push i Pattern Description This moves the viewable area within the active CCD region From the center it can be moved two click positions in the the positive negative x y O This button moves origin point When push Tele button camera go Zooms In When push Wide button camera go Zooms Out Near button camera go Focus In Far button camera go Focus Out Iris button camera go to close the IRIS Iris button camera go to open the IRIS set Saves the current position to the values in the Preset Edit box Deletes the current position to the values in the Preset Edit box Moves the PTZ to the defined Preset position Start to sa
14. Wide 97 2 Tele mm Aperture Range F1 6 Wide 3 7 Tele Minimum Illumination 1 2Lux 30 IRE Color 0 25Lux 30 IRE B W Camera 0 001 Lux 30 IRE DSS_128FLD Day amp Night Auto Day Night Focus Auto Manual SemiAuto Iris Auto Manual Shutter Speed Auto x128 1 60 sec 1 10 000 sec AGC Normal High Off White Balance Auto Manual Red Blue Gain Adjustable BLC NORMAL C L U D R HIGH LOW 6 Area Selectable Flickerless On Off Brightness Adjustable 0 96 Operation Range Pan 360 Endless Tilt 90 Preset 360 sec Operation Speed Manual 1 360 sec inter locked with zoom extension Swing 1 180 sec Pan Tilt Preset Setting 127 presets label setting individual video setting Swing Setting 8 swings Pattern Setting 4 pattern 1200 commands pattern 5 min Group Setting 8 groups 20 actions group Other Functions Auto Flip Auto Parking Power Up Action Compression SMJPEG MPEG4 H 264 Resolution D1 CIF Video Streaming MJPEG MPEGA or H 264 dual mode Audio Two way full duplex ADPCM G 726 Network Frame rate Dual Mode MJPEG 15fps MPEG4 H264 25fps Protocol IPv4 HTTP TCP RTSP RTP RTCP UDP DHCP UpnP ARP DNS DynDNS Bonjour Connected count at a time Camera live viewer for up to 10 clients Supported DDNS 1 CNB DDNS 2 DynDNS org 3 Reference code with SDK Network Security IP Filtering Privacy Zone Op
15. as default Camera Adjust should be set GLOBAL as default All characteristics can be set up in OSD menu e Set Preset hee 1 F lt Set Preset gt 1 128 e Run Preset lt Go Preset gt 1 128 Delete Preset To delete Preset use del del button or OSD menu O Swing Function By using Swing function you can make camera to move between 2 Preset positions repeatedly When swing function runs camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW Clockwise direction Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW Counterclockwise direction PB 2nd Preset AD Me De E ee zn O Ten SEA E eos A A a Ke 2 F F f ate 4 A al Poi a 7 F a ak e E y z 5 se A F i F a 4 E F ad Y 4 i Y E 4 1st Preset O a In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd point Camera turns on its axis by 360 in CW Clockwise direction and then it turns on its axis by 360 in CCW Counterclockwise direction Speed can be set up from 1 sec to 180 sec e Set Swing To set Swing use OSD menu e Run Swing Swing LP lt Run Swing gt 1 8 e Deleting Swing To delete Swing use OSD menu Cor Ged Demo Bates jp and Pattern e Function e Setting Pattern e Run Pattern Delete Pattern O Group e Function e Setting Group e Run Gro
16. gets during preset movement As soon as camera stops at preset end point camera start displaying live images which it gets at preset end point This function is only available with 30x EXview 27x 36x Models Mm PARK ACTION SETUP If Park Enable is set to ON camera runs assigned function automatically if there is no PTZ PARKING ACTION SETUP command during assigned Wait Time PARK ENABLE OFF WAIT TIME 00 10 00 e PARK ENABLE ON OFF PARK ACTION IOME WAIT TIME 1 minute 4 hours The time is displayed with hh mm ss format and you can change this BACK by 1 min unit EXIT MENU OFF e PARK ACTION HOME PRESET PATTERN SWING GROUP If it is set to HOME all the functions go back to HOME position PAN TILT ZOOM 0 O x1 Cor Head Demo Hates jp and 4 OSD Menu MW ALARM ACTION SETUP Sets the preset to move to when the alarm is input ALARM ACTION SETUP EE TNT ALARM N ACT NOT USED PRESET 1 128 ALARM ACT NOT nn ALARM 2 ACT NOT Assign counteraction Preset position to each Alarm input ALARM 3 ACT NOT ALARM 4 ACT NOT The uppercase N indicates the alarm index BALK EALT MENU OFF Preset Setup e PRESET NO 1 128 PRESET SETUP If a selected preset is already defined camera moves to pre defined position and preset characteristics such as Label and Relay Outputs PRES WU PRESET NU show on monitor If a selected preset is not defined UNDEFINED CLR P
17. in the D1 Mode the transmitted fame rate is reduced by up to 15 fps Enables or disables the Alarm sensor Event Mode Motion Detection Enables or disables Motion Detection When processing an event this establishes the number of images to be saved per Capture Frame second It can be selected between 1 and 3 When processing an event this establishes saving images before the occurance of the event Pre Alarm Event Setting It can be between 1 and 5 seconds before the event and the number of the images to be saved gets determined by the Capture Frame rate When processing an event this establishes saving images after the occurance of the event Post Alarm It can be between 1 and 8 seconds after the event and the number of the images to be saved gets determined by the Capture Frame rate Enables or disables scheduled event monitoring When Always is selected while Event Alarm is activated the unit will monitor event Event Schedules Alarm all the time During Time is selected while Event Alarm is activated the unit will monitor event Event Schedules Alarm during the time period specified Event Schedules Specifiy schedule for Event Alarm monitoring Event Alarm is monitored according to Setting the schedule specified here This allows Alarm images to be uploaded to an FTP server when processing an event The Upload image to FTP client PC has to run FTP server to receive the images and the information
18. lines of them is connected in parallel as shown below Client Internet LAN WAN Y ROUTER Cator Ged Demo Arias jp and 2 Installation Mm Sensor Input Relay Output e Sensor input connection Internal Circuit 5V 12V IN 1 Sensor Output 1 63 Sensor Output4 Before connecting sensors check driving voltage and output signal type of the sensor Since output signal types of the sensors are divided into Open Collector and Voltage Output type in general the cabling must be done properly after considering these types Also the sensor type i e Normal Open or Normal Close in DIP switch in main body of camera must be set properly Signal Line Description IN COM Connect cable of electric power source for sensors to this port as shown in the circuit above IN1 IN2 IN3 In4 Connect output of sensors for each port as shown in the circuit above e Relay output connection Internal Circuit AC or DC ai OUT 1 AC or DC i j ii OUT 2 Maximum allowable electrical load of relay is shown bellow table Max Capacity 28VDC 3A 110VAC 3A 250VAC 3A Cator Head Demo Arias jp and 3 Operation Check Points before Operation e Before power is applied please check the cables carefully e If you changed camera protocol by changing DIP switches the change will be effective after you reboot the camera System Control Logging On You can log on a
19. of the FTP server has to be accurately entered and saved at the FTP Cofiguration page Event Output Alarm Output Port This sends out Alarm signal to its output port during event processing This allows Alarm images to be sent out by an e mail when processing an event Only Send Image to Email one image file at the moment of the event gets sent out The e mail address has to be accurately entered and saved at SMTP configuration page Save Image to Internal This allows Alarm images to be saved in the internal memory Saved image can get Select Memory transferred to the client s PC by using save image button at system configuration page Save Image to SD This allows Alarm images to be saved in the external memory SD Card SD card has to Memory be properly installed and recognized for this feature Not Supported x27 x36 a Applies and saves changes Storage Recalls previously saved configurations Cor Head Demo Arias jp and 5 IP network Part SMTP Setup This configures mailing out method of alarm Images once event occurred in the XPEED XNET system Click gt SMTP button to open the page shown in Figure 5 20 CNB Network Camera Setup Page Windows Internet Explorer Sele Go v http 192 168 123 100 html view index html stamp 1 256596671 765 Pr File View Favorites Tools Help w we CNB Network Camera jm CNS sun MADE EED E System Setup Status Sender SMTP Setting
20. option pages Loads up Log Messages file stored in the XPEED XNET product Load List Log Message file can be sorted with date and index Click Load List button to view messages list in the Listbox Log Report Logs View Select a file from the Log List and click Logs view button to view Logs Del Select a file from the Log List and click Delete button to delete Select a file from the Log List and click Save Logs button to save the file to PC Cation Ged Demo Bates jp and 5 IP network Part Configuring Audio XPEED XNET s Audio features can be configured in this page Click P Audio button to open the page shown in Figure 5 11 NG Network Camera setup Page Windows Internet Explorer 0 Gr le htto 7 192 168 123 100 htm1 view index htm stamp 1258596871 765 E 4 x Live Search ler File Edit View Favorites Tools Help 7 gt gt ve de amp CNB Network Camera A ae lp CNS senno AND GES GS CI System Setup Users C Enable Audio Date amp Time Multi Viewer Audio Input PTZ Configuration Source Microphone Maintain Server System Log Encoding Audio amp Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP E 100 Figure 5 11 Audio configure page Cator Ged Demo Arias jp and me e as Audio Enables or disables Audio feature
21. BACK CANCEL Cor Head Demo Hates jp and 4 OSD Menu System Initialize SYSTEM CLEAR CLR CLR CLR L CLR REBOOT INITIALIZE ALL DATA DISPLAY SET CAMERA SET MOTION SET EDIT DATA CAMERA BACK EXIT MENU OFF B Initial setting CLEAR ALL DATA CLR DISPLAY SET CLR CAMERA SET CLR MOTION SET CLR EDIT DATA REBOOT CAMERA Deletes all configuration data such as display camera motion setup and so on Initializes Display Configuration Initializes camera Configuration Initializes Motion Configuration Deletes Preset Data Swing Data Pattern Data and Group Data Reboots Zoom Camera module e Display setting e Camera setting Camera ID PTZ Information Action Title Preset Label Alarm I O North Direction Privacy Zone m OFF AUTO AUTO AUTO AUTO PAN 0 UNDEFINED Focus mode Digital Zoom Max Zoom Flickerless Color Line Lock White Balance Mode Backlight Day amp Night Slow Shutter m AE Mode Brightness m SEMIAUTO ON O m X270 0 X432 e Motion setting e User setting data Motion Lock Power up Action Auto Flip Jog Max Speed Jog Direction Park Action Alarm Action FRZ IN PRESET m ON ON 120 SEC INVERSE OFF OFF OFF Preset 1 128 Swing 1 8 Pattern 1 4 Group 1 8 Above functions are only available with the following models ISS2765N P Option ISS2965N P X m UNDEFINED UND
22. CNS System Setup Status Users Date amp Time Multi Viewer Maintain Server System Log Audio amp Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP f UPnP DynDNS Menu OFF Menu OFF Event Configuration Back Far Event Types SMTP E mail ea Moving Speed Setup Pan Speed 49 Tilt Speed Figure 3 4 OSD menu selection Cator Head Demo Arias jp and 3 Operation Preset and Pattern Function Pre Check e Check how to operate preset and pattern function with web viewer or CMS in advance to operate camera function fully when using web viewer or CMS e Refer to the following table Input Preset Number and press Preset go button lt Set Preset gt Input Preset Number and press Preset set button lt Run Pattern gt Input Pattern number and press Pattern run button lt Set Pattern gt Input Preset Number and press Pattern red button Starting OSD Menu e Function Using the OSD menu Preset Pattern Swing Group and Alarm I O function can be configured for each application e Enter Menu press Munu On Button in setting Web page Preset Function Max 127 positions can be stored as Preset position The Preset number can be assigned from 1 to 128 but 95 is reserved for starting OSD menu Camera characteristics i e White Balance Auto Exposure can be set up independently for each preset Label should be blank and Relay Outputs should be set to OFF
23. D 30 SEC 2ND POS CANCEL CLEAR SWING BACK EXIT MENU OFF SWING SPEED CLEAR WING 1 8 Selects Swing number to edit If a selected Swing has not defined NOT USED is displayed in 1st Position and 2nd Position PRESET 1 128 Set up the 2 position for Swing function If a selected preset is not defined UNDEFINED will be displayed as shown below SWING SETUP SWING NO 1 1ST POS 2ND POS NOT USED 3 UNDEFINED When swing function runs camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW Clockwise direction Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point is CCW Counterclockwise direction In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd point camera turns on its axis by 360 in CW direction and then it turns on its axis by 360 in CCW direction 1 sec 180 sec Sets Swing speed from 1 sec to 180 sec CANCEL OK Deletes current Swing data Cor Head Domo Hates jp and 4 OSD Menu Pattern setup e PATTERN NO 1 4 Selects Pattern number to edit If a selected pattern number is not PATTERN SETUP defined UNDEFINED will be displayed under selected pattern PATTERN NO 1 b UNDEF INED hade CLR PATTERN CANCEL EDIT PATTERN e CLR PATTERN CANCEL OK Deletes data in current pattern BACK E
24. DIT PATTERN Starts editing pattern EXIT MENU OFF Mm EDIT PATTERN By using Direction KEY move to start position with appropriate zoom EDIT PATTERN 1 e ha p PProp To start pattern recording press NEAR key To exit this menu press FAR key MOVE TO START POSITION NEAR START FAR CANCEL EDIT PATTERN 1 Move camera with Direction KEY or run preset function to memorize the path mostly curve MAA eee pea eK Adio AR path in a selected pattern The total memory size and the rest memory size is displayed in the form of bar Maximum 1200 communication commands can be stored in a pattern To save data and exit press NEAR key To cancel recording and delete record data press FAR key NEAR SAVE FAR DELETE Cor Head Demo Hates jp and 4 OSD Menu Group Setup GROUP SETUP GROUP NO 1 UNDEF INED CLEAR GROUP CANCEL EDIT GROUP BACK EXIT MENU OFF MW EDIT GROUP EDIT GROUP 1 NO ACTION DWELL OPT NONE 2 NONE NONE NONE NONE BACK CANCEL NEAR EDIT EDIT GROUP 1 NO ACTION DWELL OPT q NONE 2 NONE NONE NONE NONE BACK NEAR EDIT ACT CANCEL FAR EDIT END EDIT GROUP 1 NO ACTION DWELL OPT NONE gt NONE NONE 4 NONE 5 NONE BALK gt MOVE CURSUR CANCEL 4 CHANGE VAL e GROUP NO 1 8 Selects a group number If the selected number is not set UNDEFINED will be displayed selected Group number e CLEAR GROUP CANCEL OK Clea
25. EFINED UNDEFINED UNDEFINED Cor Head Demo Bates jp and 5 IP network Part system Administration Logging On You can log on as an administrator using either Internet browser or CMS software This manual will describe about using Internet browser only Using Internet Explorer Type the IP Address of the XPEED XNET product in the address bar and press enter Ex http 192 168 123 100 If the HTTP port has been changed from the default value enter the new port as shown below IP Address of the XPEED XNET Port No Ex http 192 168 123 100 8080 ID and Password If you are logging in as an administrator the Log In box will appear as shown in figure 5 1 Basic Setup page will appear when you enter id and password Cator Ged Dime Arias jp and 5 IP network Part Operating the Camera When you log in as an administrator XPEED XNET s Basic Setup page will appear as shown in Figure 5 1 Setup pagers for different features can be accessed from this page Access to each feature are controlled by different user groups Administrator Operator and Viewer CNB Network Camera Setup Page Windows Internet Explorer Ge le hen 192 168 123 100 htmi view index htmI stamp 1258596871 765 NX Edit flew Favorites Tools Help we av CNB Network Camera o CNS sun SEESE CI System Setup Status User List Users User Name User Group Date Time roo
26. G4 amp H 264 Appearance Bit rate IM bps Sub Stream MJPEG Resolution DI Frame Rate Control Frame rate E MJPEG Appearance Quality BC Figure 5 12 Video configure page Outdoor Head Demo Hates jp andt Description Select a resolution of the video image Resolution CIF D1 lt Default D1 gt Select Video Codec Main Stream Select among MJPEG MPEG4 and H 264 Turns Sub Stream feature on or off lt Default Disable gt Enable Sub Stream output is in MJPEG with maximum 15 frame per second Dual Codec When configuring select Main Stream or Sub Stream in the Index page Enable Dual Codec checkbox is enabled when Codec is set up as MPEG4 or H 264 Frame Rate Selects Frame rate of Video output Frame rate Control 1 30 Frame MJPEG Appearance Select MJPEG s video quality between 1 and 100 Mpeg4 amp H 264 Bit rate Selects bit rate for MPEG4 or H 264 video signal between 128kbps and 3Mbps Appearance sen Selects resolution of sub stream video among CIF D1 Frame Rate Frame rate Select Frame rate of sub stream video between 1 ans 15 frames per second ontro MJPEG Select sub stream video quality between 10 and 100 Appearance Cator Ged Dime Arias jp and 5 IP network Part Configuring RTP RTSP This is related to XPEED XNET s DDNS server information Click gt RTP RTSP to open the page shown in Figure 5 13 CNB Network Camera Setup Pagel Windows I
27. ID OFF PTZ INFORMATION AUTO ACTION TITLE AUTO PRESET LABEL AUTO ALARM 70 AUTO SET NORTH DIRECTION PRIVACY ZONE BALK EXIT MENU OFF MB COMPASS DIRECTION SETUP SET NORTH DIRECTION MOVE TO TARGET POSITION NEAR SAVE FAR CANCEL e SYSTEM INFORMATION Displays system information and configuration e DISPLAU SETUP Enable Disable of OSD display on Main Screen e DOME CAMERA SETUP Configure various functions of this camera e SYSTEM INITIALIZE Initializes system configuration and sets all data to factory default configuration This menu defines Enable Disable of OSD display on main Screen If an item is set to be AUTO the item is displayed only when the value of it is changed e CAMERA ID ON OFF e PTZ INFORMATION ON OFF AUTO e ACTION TITLE ON OFF AUTO e PRESET LABEL ON OFF AUTO e ALARM I O ON OFF AUTO Set North to assign compass direction as criteria Move camera and press NEAR button to save Cor Head Demo Hates jp and 4 OSD Menu Privacy Zone Mask Setup Models ISS2965N P X and ISS2765N P Only PRIVACY ZONE FMASK NO UNDEF INED DISPLAY OFF CLEAR MASK CANCEL EDIT MASK BALK EXITCMENU OFF B Privacy Zone Area Setup SET NORTH DIRECTION MOVE TO TARGET POSITION NEAR SAVE FAR CANCEL M Privacy Zone Size Adjustment EDIT MASK ADJUST MASK WIDTH 4 ADJUST MASK HEIGHT NEAR SAVE FAR CANCEL Select area in image to mask
28. Input Sensor Active Type S S vd e When a sensor input is used its functional type should be set 6 6 9 There are two types Normal Open type and Normal Close type Normal Open Voltage is let out when the sensor Is activated Normal Close Voltage is let out when the sensor s not activated Sensor 1 Normal Close ST1 Pin 4 Sensor 1 Normal Open Sensor 2 Normal Close ST2 Pin 5 Sensor 2 Normal Open Sensor 3 Normal Close ST3 Pin 6 Sensor 3 Normal Open Sensor 4 Normal Close ST4 Pin 7 Sensor 4 Normal Open e If a wrong type of sensor is selected it activates in the opposite way to the sensor input Chutdoor Heet Dome Doris jp and NW General LAN WAN Configuration Client Internet LAN WAN ROUTER Cutdeor Head Demo Arias jp and 2 Installation Installation Using the Wall Mount Dinora aa ee ae a 2 Wire cables to terminal blocks on the PCB in Wall Mount Bracket 3 Hook up Drop Prevention Spring on main body to prevent Line up the mold lines and assemble main body to camera from unexpected drop and connect Main Body Wall Mount Bracket Cable to Main Body Connector in Wall Mount Bracket 5 Turn main body on its axis in CW Clockwise direction and after assembling them screw main body to Wall Mount Bracket to protect them from separation by vibration or others 6 In case of using pipe use the hole located on lower side of Wall Mount Bracket to
29. NB Network Camera Setup Pagel Windows Internet Explorer KEk JS v http 192 168 123 100 html view index html stamp 1 256596671 765 Y X Live Search Al File Edit View Favorites Tools Help Y Re CNB Network Camera CONS System Setup Status Users Date amp Time Multi Viewer PTZ Configuration Maintain Server System Log Audio amp Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP mm A A A R Event Enable O Enable Event Event Mode Sensor1 Sensor2 Sensor3 Sensor4 Motion Detection Note Video will stream at maximum 9fps ifthe motion detection is enabled on SXGA resolution Event Settings Capture Frame 2 fps 1 3 Pre Alarm 2 sec 1 5 Post Alarm sec 1 8 Event Schedules Always During time Sun Mon Tue Wed Thu Fri Sat Start time O hh mm End time O o hhimm Event Output Upload image to FTPL FTP Setting Alarm output port Send image to email SMTP SMTP Setting Select Storage Save image to internal memory Save image to SD memory View Load saved images Open Port 1 65535 Figure 5 19 Event Types page Outdoor Head Demo Hates jp andt Description Enables or disables event processing lt Default Disable gt lt Note for users gt Event Enable Enable Event o When this is enabled
30. P IP parameters This configures XPEED XNET s network related parameters Click gt TCP IP button to open the page shown in Figure 5 14 CNB Network Camera Setup Page Windows Internet Explorer EEx EE Ge le hen 192 168 123 100 html view index htm stamp 1258596871 765 File Edit View Favorites ww CNB Network Camera CNB System Setup Status Users Date amp Time Multi Viewer PTZ Configuration Maintain Server System Log Audio amp Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP IP Address Configuration Obtain an IP Address automatically DHCP Use the following IP Address 192 168 123 100 IP Address Subnet Mask 255 255 255 0 Default Gateway 192 168 123 254 DNS Configuration Primary DNS Server 165 125 53 1 Secondary DNS Server NTP Configuration NTP Address Hostname Configuration Use the Host Name CNB_IPCAM MAC Address MAC Clone 80 de lef 1 54 87 Dc Reset MAC Addr Figure 5 14 Network Setup page Cor Head Demo Hates jp andt Description Turns DHCP on or off Check DHCP checkbox to get an IP address automatically from the network using DHCP Enable DHCP protocol Obtained IP address can
31. RESET CANCEL shows on monitor EDIT SCENE EDIT LABEL LABEL123 RELAY OUT 1 CLR PRESET CANCEL OK CAM ADJUST GLOBAL ias Delete current Preset data BACK EXIT MENO OFF EDIT SCENE Redefine current Preset scene position i e PTZ EDIT LABEL Edits Label to show on monitor when preset runs MAX 10 alphabets are allowed e RELAY OUT Sets the relay output The figure on the right is current Setting value indicates OFF mode If the relay is shown as figures it means relay is ON e CAM ADJUST GLOBAL LOCAL WB White Balance and AE Auto Exposure can be set up independently for each preset There are 2 modes Global mode amp local mode The Global mode means that WB or AE can be set up totally and simultaneously for all presets in ZOOM CAMERA SETUP menu The local mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu Each Local WB AE value should activate correspondingly when camera arrives at each preset location During jog operation Global WB AE value should be applied All Local WB AE value should not change although Global WB AE value changes If local is selected Menu to set WB AE shows on monitor Cor Head Demo Hates jp andt 4 OSD Menu Mm EDIT PRESET SCENE Using Direction KEY move camera to desired position EDIT SCENE PRESET 1 By pressing NEAR key save current PTZ data Press FAR key to cancel
32. Zoom Magnification 27x Optical Zoom 10x Digital Zoom Max 270x Zoom Model ISS2765N P 36x Optical Zoom 12x Digital Zoom Max 432x Zoom Model ISS2965N P X e True Day amp Night Function e Various Focus Mode Auto Focus Manual Focus SemiAuto Focus Each Preset has its own video configuration label relay output setting values You can adjust each Preset setting independently B Powerful Pan Tilt Functions Max 360 sec high speed pan Tilt Movement Using Vector Drive Technology Pan Tilt motions are accomplished in a shortest path As a result time to target view is reduced dramatically and the video on the monitor is very natural to watch For jog operation using a controller since ultra slow speed 0 05 sec can be reached it is very easy to locate camera to desired target view Additionally it is easy to move camera to a desired position with zoom proportional pan tilt movement B Preset Pattern Swing Group Privacy Mask and More Max 127 Presets are assignable and characteristics of each preset can be set up independently such as white Balance Auto Exposure Label Digital Outputs and so on Max 8 set of Swing action can be stored This enables to move camera repetitively between two preset positions with designated speed Max 4 of patterns can be recorded and played back This enables to move camera to follow any trajectory operated by joystick as closely as possible Max 8 set of Gro
33. arc File Edit View avorites Tools Help we we CNB Network Camera E gt D ape ie CNS son GD ED ESS Ci System Setup Gigh 1st Sub Channel Video Settings Users C Enable Date amp Time IP Domain RTSP Port 1 65535 Multi Viewer PTZ Configuration User Name HTTP Port 1 65535 Maintain Server Password System Log Audio amp Video A ee Audio O Enable Video IP Domain RTSP Port 1 65535 T REE User Name HTTP Port 80 1 65535 Network Setup Password TCP IP IP Filtering 3rd Sub Channel Video Setti ERE O Enable UPnP DynDNS CMS IP Domain RTSP Port 1165535 User Name HTTP Port 80 1 65535 Event Configuration Event Types SMTP E mail FTP Password Figure 5 7 Multi Viewer Configuration Page Outdoor Head Demo Hates jp andt Description Enables viewing of 1st sub ChannelVideo from IP address entered Enable 1st This can only be enabled when IP address User Name Sub Channel Video and Password is properly entered lt Default Disable gt Ist Sub Channel Video Settings 1st IP Address Enter Ist Sub Channel s IP Address Enter 1st Sub Channel s User name Ist Password Enter 1st Sub Channel s Password Enables viewing of 2nd sub ChannelVideo from IP address entered Enable 2nd This can only be enabled when IP address User Name Sub Channel Video and Password is properl
34. automatically once its completed 1 10 minutes Figure 5 9 Server Maintenance page Cor Head Demo Hates jp anat Description Restarts the system It takes about 45 seconds Maintain l Resets all parameters except for TCP IP settings Server Light Default This restore will be followes by about 45 seconds system reset Resets all parameters to Factory Default setting Factory Default o This will be followed by about 45seconds system reset Reset Log Deletes all Log Message Initialization Delete Image Deletes all Alarm Images from the internal Flash Memory Reboot Mecha Restart the camera mecha and Camera s Condition parameters Image Camera Use this to upgrade the system Select locations of upgrade file in client PC and click upgrade button System o Upgrade This will be followed by one minute system restart Upgrade Note Please do not disconnect power and LAN cable from the XPEED XNET while the upgrade is in process It might cause a system error Upgrade File can be downloaded from http www cnbtec com This saves current configurations in client PC Back up file can be restored to other XPEED XNET cameras for only network BackUp Backup l status This will be followed by about 45 seconds system reset This loads up settings from a saved Backup file Click restore button after selecting backup files in Client PC Optional check boxes can be used to select settings to be excluded eai oe from th
35. be viewed by IP Installer default Note If the network does not use DHCP server the product will wait for server s response for two minutes and restart with its previous IP address IPv4 Address Enter an IP address Configuration IP address Configure IP address after checking IP address range configuration of the router where the XNET product is connected Enter Subnet mask Use this when you want to access only from the same subnet by masking out upper portion of the IP address Use 255 255 255 255 when you want to connect from one PC only Subnet mask Default router Enter the address of Default router Domain name Enter Domain name DNS Configuration Erman DNS Server Secondary DNS Server Enter secondary DNS address Enter address of NTP Network Time Protocol Server Enter primary DNS address NTP Configuration Network address NTP server is used when Synchronize to NTP Server is selected in Date amp Time page Host name User i Enter Host name Configuration the host name Ethernet MAC MAC Address address Enter Ethernet Address Applies and saves changes Cator Ged Dime Arias jp and 5 IP network Part Configuring IP Filtering This configures IP Filters for XPEED XNET product Click gt IP Filtering button to open the page shown in Figure 5 15 CNB Network Camera Setup Pagel Windows Internet Explorer Sele Ge E htto 192 168 123 100 html view i
36. ct should be operated only from the type of power source indicated on the marking label Precautions B Operating e Before using make sure power supply and others are properly connected e While operating if any abnormal condition or malfunction is observed stop using the camera immediately and then contact your local dealer B Handling e Do not disassemble or tamper with parts inside the camera e do not drop or subject the camera to shock and vibration as this can damage camera e Care must be taken when you clean the clear dome cover Especially scratch and dust will ruin your quality of camera B Installation and Storage e Do not install the camera in areas of extreme temperature which exceed the allowable range e Avoid installing in humid or dusty places e Avoid installing in places where radiation is present e Avoid installing in places where there are strong magnetic fields and electric signal e Avoid installing in places where the camera would be subject to strong vibrations Cation Head Demo Arias jp and Table of Contents 1 Introduction Features 5 Product amp Accessories 7 Parts Name amp Functions 8 2 Installation Dip Switch Setup 9 Installation Using the Wall Mount 11 Installation Using the Pendant Mount 12 Wire Connections 13 3 Operation Check Points before Operation 15 Preset and Pattern Function Pre Check 22 Starting OSD Menu
37. e XPEED XNET system Operator Control over Viewer Audio amp Video Setup and Event Configuration Viewer View camera s video signal only Modifies information for each user Select a user in User Listbox enter new Password User Group and click Modify button to save the changes Modify Updated detail can be viewed in User Listbox Removes a user Remove Select a user in User Listbox and click Remove button to remove Updated user list can be viewed in User Listbox Enable User anonymous Turns Anonymous Viewer mode on or off Settings viewer When enabled Web Viewer can be accessed without a log in prompt login Save Applies and saves the configurations NN Recalls previously saved configurations Cator Ged Dime Arias jp and 5 IP network Part Setting Date amp Time This page will change Date and Time of XPEED XNET system Click gt Date amp Time to open the page shown in Figure 5 6 hj Ge E hrp 122 168 123 100 ntmi view index htm stamp 1258596871 765 File Edit View Favorites Tools Help ww CNB Network Camera CNS sun GD ED ES Ci System Setup Status Current Server Time Users Date 2001 03 18 Time 23 58 57 Date amp Time Multi Viewer New Server Time PTZ Configuration TimeZone GMT 09 Seoul Osaka Tokyo Maintain Server System Log C Automatically Adjust for Daylight Saving Time Changes TimeMode Synchro
38. e restore process except TCP IP parameters Exclude TCP IP settings except Users parameters Exclude Users settings except IP Filter parameters Exclude IP Filter setting This will be followed by a one minute system reset Cator Ged Dime Arias jp and 5 IP network Part Generating Log Report Log report contains detailed information about XPEED XNET s image setup and error Click gt Log Report button to open the pageshown in Figure 5 10 NB Networ amera etup Page Windows Internet Explorer 5 Ge y e http 192 166 123 100 html view index html stamp 1256596671765 Y 4 X Live search Pp File Edit View Favorites Tools Help w we CNB rn CONS System Setup Status Users Date amp Time Multi Viewer PTZ Configuration Maintain Server System Log Audio amp Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP Ea A D B System Settings System Overview View system Log Report Log List Load current log files View selected log file Delete selected log file Save Log files Note The log file may prove useful when anomymous user use the CNB support web R 100 Figure 5 10 Log report page Cator Ged Demo Arias jp and Description System Settings System Overview Displays current configurations for XPEED XNET
39. e set when AE is in BRIGHTNESS mode Only available with ISS2965N P X Models Cor Head Demo Hates jp andt 4 OSD Menu Motion Setup Setup the general functions of Pan Tilt motions MOTION SETUP nc e MOTION LOCK ON OFF EMOTION LOCK OFF PWR UP ACTION ON If Motion Lock is set to ON it is impossible to set up and delete Preset AUTO FLIP ON JOG MAX SPEED 120 SEL Swing Pattern and Group JOG DIRECTION INUERSE It is possible only to run those functions To set up and elete those FR2 IN PRESET OFF i l PARKING ACTION SETUP functions enter into OSD menu ALARM ACTION SETUP BACK EAXIT MENU OFF PWR UP ACTION ON OFF Refer to Other Functions section e AUTO FLIP ON OFF Refer to Other Functions section JOG MAX SPEED 1 sec 360 sec Sets maximum jog speed Jog speed is inversely proportional to zoom magnification As zoom magnification goes up pan tilt speed goes down e JOG DIRECTION INVERSE NORMAL If you set this to Inverse the view in the screen is moving same direction with jog tilting If Normal is selected the view in the screen is moving reversely e FRZ IN PRESET ON OFF 30x EXview 27x 36x Models Only If Freeze in preset function mode is ON camera starts freezing the image of start point at start point of preset movement Camera keeps displaying the image of start point during preset movement and does not display the images which camera
40. era characteristics can be set up easily and directly with reserved preset not entering into OSD menu For more information refer to Reserved Preset in this manual W Easy Installation and Perfect Outdoor Environment Compatibility e Fans and heaters are built in camera for cold and hot temperature environment Also idealistic mechanical design protects camera from water and dust IP 66 e It is easy to install and maintain camera with terminal for cable connection in brackets B IP Network Control e supported multiple codec with MJPEG MPEG4 H 264 Cator Ged Demo Arias jp and 1 Introduction Product amp Accessories MB Basic Components Dome Cover AC Adaptor option ys Main Body Main Body Sun Shield L Style TORX Wrench Manual CD Camera Bracket Bracket Accessories or Wall Mount Bracket Guide Pattern Rubber Gasket Anchor Bolt Rubber Gasket Anchor Bolt Allen Hex Wrench Optional Accessories May vary by region gt Adaptor NW Other Components available to be ordered separately Manual CD IIIS Pole Mount Adapter Sems Screw IIIS Corner Mount Adapter Sems Screw Quidoor Heet Dome Dries jp and 1 Introduction O Parts Name amp Functions Dome Cover DIP Switch Main Body Cable Drop Prevention Spring Lockup Screw 6 Fuse Cabling Terminal Block Mold Line TACT Switch
41. fix pipe Cutdeor Head Demo Arias jp and 2 Installation Installation Using the Pendant Mount To pass cables to upside of ceiling please make a hole with 50 60mm diameter on the ceiling panel and attach the Ceiling mount bracket on it Line up the mold lines and assemble main body to Ciling Mount Bracket 2 Wire cables to terminal blocks on the PCB in Ceiling Mount Bracket Turn main body on its axis in CW Clockwise direction and after assembling them screw main body to Ceiling Mount Bracket to protect them from separation by vibration or others Hook up Drop Prevention Spring on main body to prevent camera from unexpected drop and connect Main Body Cable to Main Body Connector in Ceiling Mount Bracket Quidoor Heet Dome Doris jp and 2 Installation Wire Connections Sensor input Braket Terminal Block IrDA Sensor Power Door Switch COMMON PWR 64 IN1 r IN3 PWR Bf Monitor IN4 VIDEO Video output BNC Illuminati ir vans JRELAY1 VIDEO AO bij DS RELAY2 Aupio ETHERNET O wed O Relay output MB Power Connection e The standard power for the system is 24VAC 2A Please check the voltage and current capacity of rated power carefully B Video Connection e Connect With BNC coaxial cable B LAN WAN Configuration e For PTZ control connect this line to router To control multiple cameras at the same time TCP IP communication
42. h preset There are 2modes Global mode amp Local Mode The Global mode means that WB or AE can be set up totally and simultaneously for all presets in ZOOM CAMERA SETUP menu The Local mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu Each Local WB AE value should activate correspondingly when camera arrives at each preset location During jog operation Global WB AE value should be applied All Local WB AE value do not change although Global WB AE value changes This mode exchanges focus mode automatically between Manual Focus mode and Auto focus mode by operation Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation With Manual mode at preset Focus data is memorized in each preset in advance and camera calls focus data in correspondence with presets as soon as camera arrives at a preset It should shorten time to get focuses Focus mode changes to Auto Focus mode automatically when jog operation starts Cator Ged Demo Arias jp and 4 OSD Menu OSD Display of Main Screen Preset Label LABEL12345 PRESET 1 Action Title ae I 10 2 4 Alarm Information Iris an 15 4 x1 N P T Z Information e P T Z Information Current Pan Tilt angle in degree zoom magnification and a compass direction e Action Title Followings are possible Action Titles and their meaning SET PRESET xxx When Preset
43. it mm Cor Head Demo Bates jp and 6 Specifications Dimensional Drawings Wall Mount Unit mm Y Cation Head Demo Arias jp and 7 System Models amp Related Accessories System Model Numbers 27x Day Night ICR Super HAD CCD Type Image Wall Mound Type ithon Sun Shed j i e 7 IS2765PW IS2765NW 36x Day Night ICR EXview HAD CCD IS2965NXW IS2965PXW Pendant Mount Type Without Sun Shield IS2765NP IS2765PP IS2965NXP IS2965PXP Wall Moun Types E With Sun Shig d i et ISS2765NW ISS2765PW Pendant Mount Type With Sun Shield ISS2765NP ISS2765PP ISS2965NXW ISS2965PXW ISS2965NXP ISS2965PXP Dome Camera Without Sun Shield IS2765N IS2765P IS2965NX IS2965PX S Dome Camera With Sun Shield l ISS2765N ISS2765P O Related Accessories 5552000 ISS2965NX ISS2965PX Cutdoor Jead Demo Arias jp and MEMO
44. ndex htrnl stamp 1 258596871765 F x Live Search el File Ed we wt CNB Network Camera CNS sen MA E A tis System Setup Status IP Filter Address List Date Time Multi Viewer PTZ Configuration IP Address Maintain Server Add System Log Audio amp Video Warning IP Address only Audio ex 192 168 123 100 Video RTP Network Setup TCP IP IP Filtering men HTTP C Enable IP Filtering UPnP DynDNS CMS IP Filter Enable Event Configuration Event Types SMTP E mail FTP Figure 5 15 IP filtering Page Cator Head Demo Arias jp and oe en Filter IP List WEN Displays list of currently established IP Filters Adds an IP address to filter out Enter the IP Address to block and click add button to add it to IP Filtering listbox The updated list can be viewed in IP Address Listbox Up to 20 IP addresses can be added Removes an IP address from IP Filtering listbox Remove Select the IP address to remove and click Remove button to remove it from the list The updated list can be viewed in IP Address Listbox IP Filter Enable IP Turns the IP Filter on or off Enable Filtering When turned on XNET product will not be accessed from the IP addresses in IP Filtering Listbox Applies and saves changes Recalls previously saved configurations Cator Ged Dime Arias jp and 5 IP network Part Configuring HTTP
45. nize with computer time Audio amp Video Date 2009 11 19 Time 11 20 09 den O Synchronize with NTP server No link NTP server Video RTP O Set Manually Date 2001 03 18 Time 23 58 52 Network Setup TCP IP IP Filtering ais UPnP DynDNS CMS None Event Configuration Event Types SMTP E mail FTP R 100 Figure 5 6 Date and Time Page Cator Head Demo Arias jp and me Jemen Current Server Time i Displays time of XPEED XNET system Time Zone Selects Time Zone lt Default GMT 09 gt Enable Daylight Enables Disables Daylight Saving Time Time N S Ti SE E Sets Date and Time of the Server lt Default None gt Synchronize with computer time Synchronizes time and date of Client PC to Server Time Mode Synchronize with NTP server Synchronizes server s time and date to NTP Server Enter NTP Server address in Network Setup Page Set Manually Server date and time of Server manually NE Applies and saves the configurations NO Recalls previously saved configurations Cator Ged Dime Arias jp and 5 IP network Part Configuring Multi Viewer Up to 3 cameras connected to XPEED XNET s network can be displayed as sub cameras simultaneously in Multi View page Click gt Multi Viewer to copn the page shown in Figure 5 7 N xplorer Ge E no 192 168 123 100 htm1 view index htnl stamp 1 258595871765 9 e Live Se
46. nternet Explorer Sele Ge yy E http 192 168 123 100 html view index html stamp 1258596671 765 4 X L e search Lr File Edit View Favorites Tools Help w k CNB Network Camera o fp gt db CNS sen A E A ti System Setup Status RTSP Configuration Users RTSP Port 1 65535 Date Time Multi Viewer PTZ Configuration Maintain Server RTP Configuration System Log RTP Start Port 1024 65435 Multiple RTSP Port 1 65535 RTP End Port 1124 65535 Maximum number of users to connect Audio amp Video Audio Video mE Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP 100 Jr Figure 5 13 RTP RTSP page Cator Head Demo Arias jp and Description Enter RTSP Port of the Main Stream between 1 and 65535 RTSP Port RTSP Configuration The default is 554 Multiple RTSP Port Enter RTSP Port of the Sub Stream between 1 and 65535 The default is 665 Enter RTP Start Port between 1024 and 65534 RTP Start Port The default is 2000 RTP Enter RTP End Port between 1124 and 65535 RTP End Port Configuration The default is 3000 Maximum number of Enter the maximum allowable number of users connected to the Stream between 1 and 10 Connection Cator Ged Dime Arias jp and 5 IP network Part Configuring the Network TC
47. o Setup Page in order for Sub Stream Video Sub Stream To be displayed MJPEG Please refer to 5 12 for detail Opens up Multi View page Multi View Multi View page will display up to 4 video signals set up in Multi Video Player Setup Page Please refer to 5 24 for detail Cutdoor Head Demo Arias jp and 5 IP network Part Status Window Status page display XPEED XNET system s Version and its Ethernet address Clock gt Status button to open the page shown in Figure 5 4 windows Internet Explorer Go E no 192 168 123 100 htm1 view index him stamp 1258696871 765 File Edit View Favorites Tools Help ww CNB Network Camera CNS sun MADE CES E System Setup Status Advanced System Information Users Date amp Time Multi Viewer System Version PTZ Configuration lt Boot XNET A1 1 1 9 1029 gt Maintain Server lt Kernel XNET A1 1 1 9 1029 gt System Log lt Root XNET A1 1 1 9 1029 gt lt Local XNET A1 1 1 9 1029 gt Copyright C CNB Technology Inc Audio amp Video MAC Address 80 4c ef 54 87 0c Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP R 100 v Figure 5 4 Status Page Internet Explorer 7 0 Cutdoor Jead Demo Arias jp and MEMO Cator Ged Dime Arias jp and 5 IP network Part Configuring Users This can give or limit au
48. power and the frequency of camera are different When FLICKERLESS in ON Day amp Night mode goes DAY and Digital Slow Shutter mode goes OFF automatically ON OFF Switching color mode to black white mode ON OFF If Line lock sync is ON video signal is synchronized with AC power Video can be fluctuated after setting is changed AUTO MANUAL In Manual mode Red and Blue level can be setup manually 0 255 0 255 Cor Head Demo Hates jp and 4 OSD Menu Mm AUTO EXPOSURE SETUP BACKLIGHT OFF C1 C2 L1 L2 U1 U2 D1 D2 R1 R2 AE SETUP GLOBAL Sets Backlight Compensation BACKLIGHT The reference position and the level of BLC are selectable Refer to the table DAY NIGHT AUTO below Note SLOW SHUTTER AE MODE L IRIS LEVEL LGAIN LEVEL t SHUTTER SPD BRIGHTNESS BACK EXIT MENU OFF Activates SLOW SHUTTER function when luminance of image signal is too dark DAY NIGHT AUTO DAY NIGHT SLOW SHOUTTER OFF 2 128 Field It is possible to set up the maximum number of fields piled up one on another by SLOW SHUTTER function It is only available when DAY NIGHT mode is DAY AE MODE AUTO SHUTTER IRIS AGC MANUAL There are five modes of Auto Exposure function Except AUTO mode the others can be selected when DAY NIGHT mode is DAY and Slow Shutter mode is OFF IRIS LEVEL 0 255 It can be set when AE is in IRIS mode or MANUAL mode GAIN LEVEL 0 255 It can be set when AE is in AGC mode or MANUAL mode
49. r the DynDNS server Enter a password for the DynDNS server Enables or disables Bonjour Bonjour Enable Bonjour Siti When enabled you can use IP Installer s XNET Auto Search feature etting Server Name Enter Bonjour s Server Name Cator Ged Dime Arias jp and 5 IP network Part Configuring CMS This configures XPEED XNET s CMS server infomation Click gt CMS to open the page shown in Figure 5 18 CNB Network Camera Setup Page Windows Internet Explorer Sele Ge le hen 192 168 123 100 htm1 view index html stamp 1258595871765 ive Search Ar File Edit we amp CNB Network Camera CNS sen MA E A ti System Setup Status En Users CMS Port 5000 1 65535 Date Time Multi Viewer Save Reset PTZ Configuration 8 Maintain Server System Log Audio amp Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP amp 100 Figure 5 18 CMS Page Cor Herd Demo Arias jp and Enter CMS port number for communication with CMS between 1 and 65535 The default is CMS CMS Port Spb MN Recalls previously saved configurations Cor Head Demo Arias jp and 5 IP network Part Configuring Event Type This is related to XPEED XNET s DDNS Server information Click gt Event Types to view page shown in Figure 5 19 C
50. rs the current setting of a group EDIT GROUP Starts editing Group Press NEAR key in NO list to start Group setup Note that MAX 20Functions are allowed in a Group Move cursor up down and press NEAR key to set up Set up Action Dwell time and Option Note that selected item is displayed in reverse Move cursor Left Right to select items and move cursor Up Down to change each value ACTION NONE PRESET SWING PATTERN e DWELL 0 sec 4min Sets Dwell Time between functions e OPT Option It should be preset speed when preset is set in Action Is should be the number of repeat when Pattern or Swing is selected in Action Cor Head Demo Hates jp andt 4 OSD Menu Set up items such as Action Dwell and OPT EDIT GROUP 1 NO ACTION DWELL OPT PRESET 1 00 03 360 NONE NONE NONE NONE BACK MOVE CURSOR CANCEL 44 CHANGE VAL After finishing setting up a Action press NEAR key to one upper Level Menu Step EDIT GROUP 1 Move cursor Up Down to select Action Number and repeat Step Step to edit selected PQ RS Group NO ACTION DWELL OPT 1 PRESET 1 00 03 360 2 NONE NONE NONE j NONE BACK NEAR EDIT ACT CANCEL FAR EDIT END After Finishing setting up all Action press FAR key to exit EDIT GROUP 1 Then cursor should be moved to SAVE Press NEAR key to save data NO ACTION DWELL OPT PRESET 1 00 03 360 NONE NONE NONE NONE
51. s Users C Enable Internal SMTP Server Date Time Multi Viewer PTZ Configuration Maintain Server SMTP Port System Log Enable SMTP Authorization SMTP Server Name 1 65535 User Name Audio amp Video Password Audio Video RTP Receiver E mail Address Setting Email Address 1 Network Setup Email Address 2 TCP IP IP Filtering HTTP UPnP DynDNS CMS Email Address 3 Event Configuration Event Types SMTP E mail FTP Figure 5 20 SMTP Page Cor Herd Demo Arias jp and Turns Internal SMTP Server on or off Enable When this box is checked Alarm Image gets mailed out through an internal mail server Mail Internal SMTP Authentication cannot be used in this mode Server When this box is unchecked Alarm Image gets mailed out through an external mail server Mail Authentication port user password mail address etc needs to be configured Enable SMTP Ek Enables or disables the use of SMTP authorization when using external mail server Authorization SMTP Settings SMTP Server Name Enter the name of external mail server SMTP Port Enter the port number for the external mail server User name Enter the user name of the external mail server Password Enter the password of the external mail server user E mail Address Email Address Enter the e mail address of the external mail server user Setting NS
52. s an administrator using either Internet browser or CMS software This manual will describe about using Internet browser only Using Internet Explorer Type the IP Address of the XPEED XNET product in the address bar and press enter Ex http 192 168 123 100 If the HTTP port has been changed from the default value enter the new port as shown below IP Address of the XPEED XNET Port No Ex http 192 168 123 100 8080 ID and Password If you are logging in as an administrator the Log In box will appear as shown in figure 3 1 Basic Setup page will appear when you enter id and password The default user name and password is root and admin respectively For security purpose it is recommended to change the administrator s id and password from their default values Please be careful not to forget them or expose them to others Please refer to figure 5 5 for detail If you forget the administrator s password Factory Reset is the only way to regain access However since this will retrieve all default settings you need to configure the network settings using IP installer software again Cation Head Demo Arias jp and CNB Network Camera Windows Internet Explorer AE http 192 168 123 100 htrnl view index html stamp 1258596671 765 kedi Live Search Fie Edit View Favorites Tools Help w CNB Network Camera f fy gt dh CNB Network User name Pas
53. s flickering which happens when the frequency of the power and the frequency of camera are different e COLOR ON OFF Switching color mode to black white mode LINE LOCK ON OFF If Line lock sync is ON video signal is synchronized with AC power Video can be fluctuated after setting is changed MB WHITE BALANCE SETUP WB MODE AUTO MANUAL WB SETUP GLOBAL In Manual mode Red and Blue level can be setup manually TUB MODE AUTO LRED ADJUST BLUE ADJUST RED ADJUST 10 255 e BLUE ADJUST 0 255 BACK EXIT MENU OFF Cutdoor Ged Demo Arias jp and 4 OSD Menu Mm AUTO EXPOSURE SETUP AE SETUP GLOBAL BACKLIGHT OFF DAY NIGHT AUTO AE MODE AUTO c IRIS LEVEL L GAIN LEVEL L SHUTTER SPD L BRIGHTNESS BACK EXIT MENU OFF BACKLIGHT DAY NIGHT AE MODE IRIS LEVEL GAIN LEVEL SHUTTER SPEED BRIGHTNESS WDR ON OFF Sets Backlight Compensation AUTO DAY NIGHT AUTO SHUTTER IRIS GAIN BRIGHT MANUAL Selects automatic exposure mode Each mode appears with adjustable values When Flickeress mode is ON AE mode is automatically in SHUTTER SPEED mode CLOSE F1 6 F28 Model S1465N P X S1965N P X CLOSE F1 4 F22 Model S1665N P X It can be set when AE is in IRIS mode or MANUAL mode 3dB 28dB It can be set when AE is in MANUAL mode 1 1sec 1 10000sec It can be set when AE is in SHUTTER SPEED mode or MANUAL mode 0 31 It can b
54. s such as system restart factory default settings system upgrade Saving configurations saving images and other additional features Click gt Maintain Server to open the page shown in Figure 5 9 NB Networ amera etup Page Windows Internet Explorer s E htp 192 168 123 100 htrl view index html stamp 1258598871765 Fie Edit View Favorites Tools Help ww CNB Network Camera CONS System Setup Status Users Date Time Multi Viewer PTZ Configuration Maintain Server System Log Audio 8 Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP Server Restart Restart the CNB Network Camera Light Default Resetto factory default except for TCP IP amp HTTP Factory Default Reset to factory default setting for all values c initializat Delete Logs Delete all log files in log directory Delete Images Delete all image files in image directory Reboot Mecha Reboot speed dome mecha i Expor as user defined custom settings Import user defined custom settings Location Gua Fee C except TCP IP 8 HTTP parameters O except Users parameters O except IP Filter parameters C except Camera Condition parameters System Update Update the CNB Network Camera with the lastest systemware Warning Do not power off during the update process Unit will be restarted
55. sword Dual Stream Service RTP over TCP _ vw Main Stream MPEG4 H 264 MJPEG Sub Stream MJPEG Note UDP can cause a network overload in a network with low bandwidth poor performance Therefore we recommend to use UDP in local networks or high bandwidth networks only ULL Figure 3 1 Log in window Cor Head Demo Arias jp and Configuring PTZ This configures XPEED XNET s PTZ information Click gt PTZ Configuration to open the page shown in Figure 3 2 CNB Network Camera Setup Page Windows Internet Explorer Sele Go ie http 192 168 123 100 html view index html stamp 1258596871765 1 Live Search File Edit View Favorites Tools Help ww CNB Network Camera o CIN ET System Setup Status Users Date amp Time Multi Viewer Maintain Server System Log Audio amp Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS Menu Menu OFF Event Configuration Back Far Event Types SMTP E mail ETP Moving Speed Setup Pan Speed 4 v Tilt Speed KAR Figure 3 2 PTZ Configuration Cator Ged Demo Arias jp and Sub Field Description This moves the viewable area within the active CCD region From the center it can be moved two click positions in the the positive negative x y a direction Direction Key O This button moves origin point When push Tele button camera go Zooms In Tele Wide When push Wide button camera go Zooms Ou
56. t When push Near button camera go Focus In Near Far When push Far button camera go Focus Out lris Iri When push Iris button camera go to close the IRIS ris Iris When push Iris button camera go to open the IRIS Saves the current position to the values in the Preset Edit box Deletes the current position to the values in the Preset Edit box Moves the PTZ to the defined Preset position Start to save for Pattern End to save for Pattern Run Runs Pattern Runs defined Swing Pattern Runs defined Group fs Stops running the Pattern Swing and Group Menu On Displays camera OSD menu in screen Menu Off Displays off for camera OSD menu Ki A gt Move or change a OSD item in OSD menu Set Near set selected menu function Back Far cancel and move to selected menu function Pan Speed Select the Pan Speed of PTZ Moving Speed Setup Tilt Speed Select the Tile Speed of PTZ Set Applies and Saves selected Pan Tilt s Speed Cutdoor Head Demo Arias jp and e Configuring and operating Network PTZ This controls XPEED XNET s PTZ Click PTZ button in operator mode to open the page shown in the Figure 3 3 CNB Network Camera Windows Internet Explorer File Edit View Favorites Tools Help w k CNB Network Camera CNS 100 Figure 3 3 Web Viewer Page Cutdoor Head Demo Arias jp and Sub Field Description This moves the viewable area within the ac
57. t Administrator User Name Multi Viewer PA PTZ Configuration Maintain Server Confirm Password System Log Password Viewer User Group Operator Administrator Audio amp Video Audio Video aa RTP Network Setup User Settings TCP IP Enable anonymous viewing log in not required IP Filtering HTTP UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP 100 Figure 5 1 Basic Setup Page Basic Setup Page can be accessed from Operator group level and up If you want to access Administrator level page in this user level you need to log in as Administrator Please refer to the following table for access authority Quidoor Heet Dome Doris jp and Accessible Not Accessible mese eo eo e ci TC O A Eze ESC CI CC leo oo gt espresso mans A Erico doc TC A vea je ETS MEC E posamrege eo leo gt Messer eo eo gt amam O A O eee pa gt e lo mmo e pese po wwe aa o a S aa i wee e a e a w e a C PEC E O MEC EC noticia O FI O A a e a o Cator Ged Dime Arias jp and 5 IP network Part Live view Web Viewer When you access in IP XNET product Web Viewer page will appear automatically Viewer area displays the video output from the camera and menu bar taps that lead to each feature setting page CNB Network Camera Windows Internet Explorer Sele
58. the square can be adjusted by clicking and dragging its lower right corner and the position can be adjusted by dragging the square Click Save button once you are done definging the areas Cator Ged Dime Arias jp and 5 IP network Part Configuring Multi View Option This configures viewing of up to 4 different camera images simultaneously Multi View n Pee Click button in Administrator mode to open the page shown in Figure 5 24 The video from the XPEED XNET product gets displayed on top left and the rest display video signals coming from the IP addresses defined in the Multi viewer Setup page CNB Network Camera Windows Internet Explorer Es El http 4192 168 123 100 html view index html stamp 1256596871 765 ve de CNB Network Camera CONS Multi Stream Setting 1ch stream 2ch stream TCP 3ch stream 4ch stream E 100 Figure 5 24 Multi View Page Cutdoor Jead Demo Arias jp and MEMO Cator Head Demo Arias jp and 6 Specifications Video Signal 27x Models ISS2765N P NTSC PAL Image Pick up Device 1 4 SONY Super HAD CCD Effective Pixels Horizontal Resolution 811 H x 508 V 410K 795 H x 596 V 470K 768 H x 494 V 380K 752 H x 582 V 440K Resolution 480 TV Line S N Ratio 48 dB AGC Off Zoom 27x Optical Zoom 10x Digital Zoom Focal Length f 3 6
59. thority to users for controlling Video and other features of XPEED XNET system Click gt Users button to open the page shown in Figure 5 5 JS http 192 168 123 100 html view index html stamp 1258596871765 Fie Edit View Favorites Tools Help we fe CNB Network Camera CNS sn MAA EA Ci System Setup i i Status User List Users User Name User Group Date amp Time root Administrator User Name Multi Viewer PTZ Configuration Maintain Server Confirm Password System Log Password Viewer User Group O Operator Audio 8 Video O Administrator Audio Video pe RTP Network Setup User Settings TCP IP IP Filtering HTTP UPnP DynDNS CMS Enable anonymous viewing log in not required Event Configuration Event Types SMTP E mail FTP R 100 Figure 5 5 Users Configuration Page Outdoor Head Demo Hates jp anat oma swr n Displays list of registered users User List root is the system s administrator root cannot be added or deleted Only the password for root can be changed This adds a new user Select Add_User tap in User List Box To add a new user enter User name Password and User group then click Add button Updated User list can be viewed in User List Box Up to 10 users can be added Add Authority of different User Groups Administrator Full control of all th
60. tion 8 Zones Alarm I O 4 inputs 2 outputs OSD Menu On Off Input Voltage 24VAC 19VAC 29VAC Input Power 48VA General Fuse 2A Dome 2 149 Dimension Housing 2 209 7 x 247 2 H mm without Sun Sheild Weight Approx 3 8kg without Sun Sheild 4 3kg with Sun Sheild Operational Temperature 30 C 50 C E Types by installation Wall Mount Sun Shield Cation Ged Demo Prid jp and 6 Specifications Video Signal 36x EXview Models ISS2965N P X NTSC PAL Image Pick up Device 1 4 SONY EXview HAD CCD Effective Pixels Horizontal Resolution 768 H x 494 V 380K 752 H x 582 V 440K 530 TV Lines S N Ratio 50 dB Weight ON Zoom 36x Optical Zoom 12x Digital Zoom Focal Length f 3 4 Wide 122 4 Tele mm Aperture Range F1 6 Wide 4 5 Tele 1 4 Lux 1 60 sec NT 1 50 sec PAL Camera Minimum Illumination 0 1Lux 1 4 sec NT 1 3 sec PAL 0 01Lux 1 4 sec NT 1 3 sec PAL ICR ON Day amp Night Auto Day Night WDR Focus Auto Manual SemiAuto AE Mode Auto Iris Shutter Manual Brightness White Balance Auto Manual Red Blue Gain Adjustable BLC On Off WDR Flickerless On Off Operation Range Pan 360 Endless Tilt 90 Preset 360 sec Operation Speed Manual 1 360 sec inter locked with zoom extension Swing 1 180
61. tive CCD region From the center it can be moved two click positions in the the positive negative x y a direction Direction Key O This button moves origin point When push Tele button camera go Zooms In Tele Wide When push Wide button camera go Zooms Out When push Near button camera go Focus In Near Far When push Far button camera go Focus Out lris Iri When push Iris button camera go to close the IRIS ris Iris When push Iris button camera go to open the IRIS set Saves the current position to the values in the Preset Edit box Deletes the current position to the values in the Preset Edit box Moves the PTZ to the defined Preset position Start to save for Pattern End to save for Pattern Runs Pattern Pattern LY Runs defined Swing Lv Group MT Runs defined Group Stops running the Pattern Swing and Group Cutdoor Head Demo Arias jp and e OSD menu selection e This page setups Preset Pattern and Swing and Group of PTZ general functin or select Alarm I O using OSD menu e OSD ON OFF Click Menu On Off button in OSD menu of control group at this page e OSD Cursor Using arrow button in OSD Menu Control Tab moves OSD menu cursor CNB Network Camera Setup Page Windows Internet Explorer GO E hto 192 168 123 100 htm view index html stamp 1258595871765 S x lt Live Search File Edit View Favorites Tools Help ww CNB Network Camera
62. tup Page Windows Internet Explorer Sele Ge yy http 132 168 123 100 html view index html stamp 1258596871 765 Live Search Lr Edit liew Favorites Tools Help we we CNB Network Camera CNS sen MA A A tis System Setup Status UPnP Settings Users Enable UPnP Date amp Time Multi Viewer PTZ Configuration Maintain Server E System Log C Enable DynDNS Friendly name CNB_XNET C Enable Anonymous Audio Video Audio Video Username RTP Alias host name autoipset com w Password Network Setup n n TCP IP i A IP Filtering C Enable Bonjour HTTP Server name UPnP DynDNS CMS Event Configuration Event Types SMTP E mail FTP E 100 Figure 5 17 UPnP DynDNS Page Outdoor Head Demo Hates jp anat eee _ Enables or disables UPnP When enabled you can use IP Installer s XNET Auto Search feature UPnP Enable UPnP Setting Friendly Name Enter UPnP s Friendly Name Enables or disables DynDNS Enable DynDNS When enabled you can automatically obtain a domain from DDNS server by simply registering the XNET product DynDNS Enables or disables DynDNS Anonymous feature When enabled DDNS service is used Enable Anonymous OE l Setting without going through authentication at Autoipset com DDNS server Alias Host Name Enter a Host Name for the DynDNS server Enter a user Name fo
63. up e Deleting Group Pattern Function is that a camera memorizes the path mostly curve path by joystick of controller and preset move functions for assigned time and revives the path exactly as it memorized 4 Patterns are available and Maximum 1200 communication commands can be stored in a pattern Pattern can be created by one of following two methods EDIT PATTERN 1 Method 1 lt Set Pattern gt Pattern NO Pattern editing screen is displayed as bellow Movement by Joystick and preset movement can be memorized in a pattern The rest memory size is displayed in progress bar NEAR SAVE FAR DELETE OO 1 N To save the recording press NEAR key and to cancel press FAR key Method 2 Using OSD Menu See the section how to use OSD Menu Pattern le lt Run Pattern gt 1 4 Use OSD menu to delete a Pattern The group function allows running sequence of Presets Pattern and or Swings Max 8 group can be stored Each group can have max 20 action entities which can be preset pattern or swing Preset speed can be set up and the repeat number of pattern amp Swing can be set up in Group setup Dwell time between actions can be set up also Dwell time A EL ee Use OSD Menu to create a Group Group LP Use OSD Menu to delete lt Run Group gt 1 8 Cator Head Demo Arias jp and 3 Operation Other Functions e Power Up Action Auto Flip e Park Action e Alarm I O
64. up action can be stored This enables to move camera repetitively with combination of preset or pattern or Swing A Group is composed of Max 20 entities of Preset Patten Swings Privacy Masks are assignable not to intrude on other s privacy 8 Privacy Zones Only available with Models 26x ISS2465N P X 18x ISS2665N P X 27x ISS2765N P and 36x ISS2965N P X MB PTZ Pan Tilt Zoom Control e With WEB browser CMS NVR cameras can be controlled at the same time E OSD On Screen Display Menu e OSD menu is provided to display the status of camera and to configure the functions interactively e The information such as Camera ID Pan Tilt Angle Alarm I O and Preset can be displayed on screen Cation Head Demo Arias jp and B Alarm I O Functions e 4 alarm sensor inputs and 2 alarm Output relays are available e To reject external electric noise and shock perfectly alarm sensor Input is decoupled with photo coupler and the relay is used for alarm output e The signal range of sensor input is from DC 5 0 to 12 0 volts to adopt various applications Meanwhile the maximum load of relay contact is 250VAC 3A or 28VDC 3A e If an external sensor is activated camera can be set to move to the corresponding Preset position Meanwhile the output relay can be matched to some specific preset positions to do counteractions such as turning on the light or sound the alarm WE Reserved Presets for Special Purpose e Most cam
65. ve for Pattern End to save for Pattern Runs Pattern Runs defined Swing Runs defined Group Stops running the Pattern Swing and Group Cator Ged Dime Arias jp and 5 IP network Part Configuring Motion Detection area This defines area that detect motion and up to three different areas can be defined in each channel Click Motion button in Operator mode to open the page shown in Figure 5 23 CNB Network Camera Windows Internet Explorer SEE E http 192 168 123 100 html view index html stamp 1256596871 765 File Edit View Favorites Tools Help ww CNB Network Camera mn CNB Figure 5 23 Motion Detection Page Cator Jead Demo Grid jp and me o e ee Displays currently defined Motion Detection area Area When an area is selected from the list its defined area gets displayed and highlighted in viewer window Up to 3 motion detection area can be defined Show selected area NINA When this is checked only the selected area gets displayed in viewer window Sets sensitivity for detecting motions 1 being the least sensitive and 10 being the most Sensitivity sensitive The user needs to configure this according to their applications and circumstances Enter a designation in the caption bar and set sensitivity Click Add button Defining A square with the designation you ve just defined will appear in viwer Motion Detection window Area The size of
66. www cnbtec com Outdoor Speed Dome Series IP XNET ver 1 0 INSTALLATION AND OPERATION MANUAL ISS2000 Series 3810 0203A Cator Head Demo Bates jp and This lightning flash with arrowhead symbol is intended to alert The user to the presence of un insulated dangerous voltage Within the product s enclosure that may be of sufficient magnitude To constitute a risk of electric shock to persons This exclamation point symbol is intended to alert the user to The presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Important Safety Instructions 1 Read Instructions Read all of the safety and operation instructions before using the product 2 Retain Instructions Save these instructions for future reference 3 Attachments Accessories Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards damage product and void warranty 4 Installation Do not place or mount this product in or on an unstable or improperly supported location Improperly installed product may fall causing serious injury to a child or adult and damage to the product Use only with a mounting device recommended by the manufacturer or sold with the product To insure proper mounting follow the manufacturer s instructions and use only mounting accessories recommended by manufacturer 5 Power Source This produ
67. xxx is stored PRESET xxx When camera reach to preset xxx PATTERN x When Pattern x is in action SWGx PRESET xxx When Swing x is in action UNDEFINED When undefined function is called to run e Preset Label The Label stored for specific Preset e Alarm Information This information shows current state of sensor input and relay output If the Input and output points are ON state it will show a number corresponding to each point When they are OFF state will be displayed Ex point 2 amp 3 of inputs and 1 of output are ON OSD will show as below e Iris When push Iris button camera go to close the IRIS When push Tris button camera go to open the IRIS Outdoor Head Demo Hates jp andt 4 OSD Menu General Rules of key Operation for Menu e The menu items surrounded with lt gt always has its sub menu e For all menu level to go into sub menu press NEAR key e To go to up one level menu press FAR key e To move from items to item in the menu use Direction KEY in the Up Down or Left Right e To change a value of an item use Up Down of the menu direction key in the web page Press NEAR key to save values and Press FAR key to cancel values e Specifications and functions should be different by models O Main Menu SPEED DOME CAMERA SYSTEM INFORMATION DISPLAY SETUP DOME CAMERA SETUP SYSTEM INITIALIZE EXITCMENU OFF Display Setup DISPLAY SETUP CAMERA
68. y entered lt Default Disable gt 2nd IP Address Enter 2nd Sub Channel s IP Address Enter 2nd Sub Channel s User name 2nd Password Enter 2nd Sub Channel s Password Enables viewing of 2nd sub ChannelVideo from IP address entered 2nd Sub Channel Video Settings Enable 3rd This can only be enabled when IP address User Name Sub Channel Video and Password is properly entered lt Default Disable gt 3rd Sub Channel Video Settings 3rd IP Address Enter 3rd Sub Channel s IP Address Enter 3rd Sub Channel s User name 3rd Password Enter 3rd Sub Channel s Password MI Applies and saves the configurations Recalls previously saved configurations Cator Ged Dime Arias jp and 5 IP network Part Configuration PTZ This configures XPEED XNET s PTZ server information Click gt PTZ Configuration to open the page shown in Figure 5 8 NB Networ amera etup Page Windows Internet Explorer LINX E http 192 168 123 100 html view index html stamp 1256596671 765 File Edit View Favorites Tools Help we e CNB Network Camera A D B gt CNS System Setup 4 A Status PTZ Setup Users A Date Time Multi Viewer Maintain Server System Log Audio Video Audio Video RTP Network Setup TCP IP IP Filtering HTTP UPnP DynDNS Menu Control Moving Speed Setup Pan Speed 4 v Tilt Speed 4 aa e Event Configuration Event Types SMTP E mail FTP IOTER

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents