Leg Instructions - Rhino-Rack
Contents
1. ER ASK EAN R z Lie Soy al Y Z Remove the cover plate to access the locking levers ds to push in Use two han the locking le vers if tight Do not used a screw driver as this may damage the carefully lift the bars out of the corresponding mounting plates J With assistance Attach Leg Base Cover when not in Page 6 of 62. flexing too much I Y 7 ZA i a i eee i gt I ront of vehicle Page 3 of 6 D Quick Mount Track Legs RLT600 3 Prepare the Leg for installation as follows 1 Remove cover plate 2 Locate and Pinch locking levers together 3 With levers pinched together push them backward into a locked position within the leg cavity Note the locking studs retracted unlocked extended The Leg is now locked Keep locking levers in Push levers back into leg position L gt cavity to locate into an I unlocked position CLA n ill rt SM Bay 4 the locking studs are locked inward this N j allows the leg to be J gt lt 3 Ke y Ss N LIN N i Na Z T placed in a mounting a R position Pull the locking levers foward to their original position They will spring back pushing the locking studs back outward fixing the leg into the mount Ensure both studs are secure in bracket Apply small amounts of downward pressure if studs do not engage Page 4 of 6 ey Quick Mount Track Legs RLT600 9 Assemble the leg hardware as shown Slide the leg into the bar and finger tighten Repeat for all 4 legs Note Leg hardware comes pre assembled Check the cross bar over hang is equal on both sides re adjust if required Tighten with a 5mm allen EQUAL OVERHANG DISTANCE AU At this point the bar can be removed and the mounting b
3. CONTROLLED RHINO RACK Quick Mount Track Legs RLT600 Important Please read these instructions carefully prior to and during installation Check the contents of kit before commencing fitment and report any discrepancies FE Si SS SSS Nereta SSSss SS Netet Netet Netet SSS SSS SSS SSS SSS SSS SSS Clean roof prior to installation Important Information Maximum carrying capacity Up to 100kg Evenly distributed over the crossbars It is essential that all bolt connections be checked after driving a short distance when you first install your crossbars Bolt connections should be checked again at regular intervals probably once a week is enough depending on road conditions usage loads and distances travelled You should also check the crossbars each time they are re fitted Make sure to fasten your load securely Ensure all loads are evenly distributed and centre of gravity is kept as low as possible Use only non stretch fastening ropes or straps Caution The handling characteristics of the vehicle changes when you transport a load on the roof For safety reasons we recommend you exercise extreme care when transporting wind resistant loads Special consideration must be taken into account when cornering and braking Please remove crossbars when putting vehicle through an automatic car wash Load ratings Maximum permissible load for system is up to 100kg p
4. ase can be fully tightened if not done so in step 2 Insert the Face plate into the leg Using the key provided insert and turn clockwise to lock the unit Remove the key Insert the cover plate and then lock using the key provided in the kit If it cannot be inserted properly it means one of the studs is not correctly fitted Check fitment and re try Note The Face Plate will cover the hardware holding the legs in place This will help to ensure your system is secure from theft Page 5 of 6 Quick Mount Track Legs RLT600 2 ps Oo gt O f Q gt Oo x Oo a ony prar O amp v D Q O O ab O C prar ab v Install the Vortex Rubber Strips It may lock the end cap Remove the key Note be easier to remove bar and complete assembly steps 8 9 and 10 metal keys can be purchased so they match the RLT600 Leg Bars Removing the O 4 z xX O O C prar C v Q O 49 Soe O C prar 0b O O v pan 0b gt O amp ae O Oo C prar 0b N 0b 0b O Y W O D Oo C prar O p q 0b _ Q 0b gt O O 0b ra pru 0b gt O 0 gt Oo O 0b oO 0b O Oo O gt 49 0b O Cc 49 _ M v lt gt gt 4 O O 0b C prar O amp y Z SS o E gs Qi
5. er pair of crossbars When crossbars are to be used in off road conditions please build a safety factor of 1 5 into this load limit Although the crossbars are tested and approved to AS1235 2000 off road conditions can be much more rigorous However increasing the number of crossbars does not increase the vehicles maximum permissible roof loading Please refer to your vehicle manufacturers handbook for the maximum roof loading allowable for your make and model vehicle Always use the lower of the two figures Note for Dealers and Fitters It is your responsibility to ensure instructions are given to the end user or client Rhino Rack 3 Pike Street Rydalmere Document No R474 NSW 2116 Australia Prepared By Kayle Everett Issue No 06 Ph 02 9638 4744 Authorised By Chris Murty Issue Date 26 10 15 Fax 02 9638 4822 These instructions remain the property of Rhino Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended Page 1 of 6 D Quick Mount Track Legs RLT600 When these roof racks are to be used on a vehicle that is driven off sealed roads the manufacturer maximum 100kg load rating ___67 kg load rating roof load rating to be found in the f Urban road Off road 50kg 1 5 vehicles User Manual should be divided by 1 5 Do not forget to subtract 5kg from your maximum carrying capacity due to the weight of iC CC
6. the crossbars and legs WARNING Important Load Carrying Instructions With utility vehicles the cabin and the canopy move independently Roofracks and vehicle can be damaged if the item transported is rigidly fixed at points on both the cabin and canopy Instead rigidly fix to either the cabin roofracks or the canopy roofracks Page 2 of 6 sy Quick Mount Track Legs RLT600 Parts List tem Component Name 73 Mexi6xt 6 Fiat Washer EF ES C Panno Layout 3 4 M6 Spring Washer 5 M6x20 Socket HD 6 Track Leg Base Cover e smm Alien Key o Track Leg Lockable Cover 4 mo 10 M6x16 Button Security B061 Screw M6x12 5 Flat Washers W003 O M6 24x21x4 Nut N057 13 Instructions R474 Tools Required Allen Key provided Metal Key provided Place M6 24x21 Hex Nut into the opening of each track at rear of vehicle Slide along the track to position Take note that the number of nuts used is vehicle and track specific eS 2 Place the mounting plate onto the track Fix in place with security screws spring and flat washers Note that the amount of fixing hardware used is dependant on the previous step and vehicle requirements For fixture to a curved section of the roof use the two closest holes to the front of the vehicle This will prevent the Track Leg Base from
Download Pdf Manuals
Related Search