User`s Manual Fully Automatic Washing Machine
Contents
1. To twist the adjustable foot please first lift up the side of the foot slightly and then you can twist the two adjustable feet Please make sure to keep the washing machine in balance The adjustable foot Install the water inlet hose NOTE The appliance is to be connected to the water mains using new hose sets and that old hose sets should not be reused Confirm the water faucet It is required that the front end shall be longer than 10mm The exit end face of the faucet shall be flat and smooth If not please file it to avoid leakage water faucet suitable water faucet not suitable The exit end face of the faucet Connection between the water inlet hose jointer and the water faucet water inlet hose jointer 1 Press the lower end of the lock lever and push Slider down the slider Take off the water inlet hose jointer from the water inlet hose component See to Figure 1 2 Loosen the screw till the water faucet can be accessed Put the jointer of the water inlet hose on the faucet See to Figure 2 If the faucet is too large and the jointer can not be set on the water faucet please loosen the four screws and take out the bushing in the jointer The front end of the faucet must be smooth otherwise it may leak water See to Figure 3 Screw knife Figure 2 Figure 3 3 Fasten the four screws evenly See to Figure 4 4 Take off the nameplate Twist the fastening nut as per the indication of the2. cover intermitting the washing machine will begin to work after a period time this is normal phenomenon Only select RINSE program If there s water inside the tub the machine will spin before rinsing If there s no water the machine will rinse directly 3 Push G button select suitable water level After switching on the power the washing machine will execute fuzzy program automatically to detect the cloth during the standard program After defection it can set the water level automatically To select other water level first push the START PAUSE button then push the WATER LEVEL button to set the water level The pulsator will not rotate unless the water is filled to selected water level 4 Push button to select suitable reserve wash program After switching on the power the reserve program is set to off mode automatically If you need to set the washing procedure to be finished at reserved time please push the RESERVE button to set the reserve wash program Refer to reserve button in Page 11 for selection Confirm the operation of reserve program When the RESERVE function is activated the indicator light of the program you have set will be off The RESERVE HOURS and REMAIN MINUTES indicator lights will be on During reserve procedure ate push the RESERVE button to display the reserve time mode E To change the running program or cancel the reserve s
3. ee eee e During pause push this button to restart e The digitron displays the time remained o W and go on working ee in minute before the washing is finished ees E r e Push down the reserve button The reserve e s Se eeesr errr eeereaeseerees j indicator light is on the digitron displays the e eeeeeeee geecee e reserve time of finishing washing in hour REMAIN MINUTES e When the machine is started the reserve e FLASH LIGHT indicator light is on indicating that the asufc so fO Qsoak _ e reserve function is running e re SOs PEO OSRD aze aLOso SMO Osor Coececeeeececeeeeeeeeeeeeeeee E Pi RO ouek i e e eeeeeseoeengeneeee ee 888 O The washing machine can detect the laundries automatically during the STANDARD program After detection it will set the water level to suitable value among 30L 40L and 50L automatically POWER ON OFF RESERVE WATERLEVEL _ PROGRAM td e The water level decided may be different gt o Esai eslicablesituston e from actual value because of the different eee oa E enwen atenemeanmaat nis moisture level of the laundries e e SOAK Washing the relatively big thick or very m You can also set water level by yourself o dirty laundries EE r Sec cca siden ccae cusses seeebceesnedce se E eee cnss ees dee see e After the machine is started i
4. figure to seal up the exit end face of the faucet See to Figure 5 Remark Before installation the threading is 4mm above the upper surface of the nut After installation the threading is 2mm above the upper surface of the nut See to Figure 6 Figure 5 Figure 6 Connection between the water inlet hose and the washer 1 Do not take off the water absorption cushion Please check if the cushion is dropped or damaged before each usage If it happens please contact our after sale department immediately nut of the water inlet hose 2 Put the nut of the water inlet hose on the valve Joo Ig jointer jointer of the water absorption cushion og 2 water inlet valve 3 Fasten the nut Swing it gently to confirm if itS suitable Connection between the jointer of the water inlet hose and the water inlet hose 1 Push down the slider Insert the water inlet hose into the jointer 2 Hang the lock lever to the jointer Release the slider till a click sound is heard Check the connection between the jointer of the water inlet hose and the water faucet 1 Swing the hose gently to confirm if it is fastened stable 2 After installation open the faucet to check if it leaks 3 Do not bend the hose with overstrain 4 Bfore each usage please check if the connection between the jointer of the water inlet hose and the water faucet and 77 the installation of the water inlet hose are firm so as to d 6 prevent dropping from imprope
5. plug tightly Fill water to the preset position Insert the power plug tightly Close the top lid Set the laundries flat Adjust the machine to be even Reorder the laundries and close the top lid Remove the foreign materials Fasten the jointer properly Common phenomena Phenomena Explanation The spinning is intermittent when it starts Balance the laundries to avoid slanting Push the spin button to select Spin but it doesn t The program is setting the drain time Some time is work needed before it starts spinning The final spinning is finished it becomes rinsing and Because the washing clothes lean to one side the begins to inlet water safety switch acts After water filling and running eliminating the eccentricity of washing clothes then beginning to spin There may be some water flowing out of the drain hose It is the water remained in the factory inspection of in the first use of machine performance Specification Rated voltage Frequency 220 240V 50Hz Water level Water quantity about 1 12L 2 18L 3 24L 4 30L 5 35L 6 40L 7 45L 8 50L Injection pressure 0 03 MPa 1 0 MPa Max Washing Max Spinning capacity 7 5kg 7 5kg 15
6. sure to ensure the washer is placed under the room temperature more than 2 hours and then use otherwise the washing effects may be lowered or the washer may be damaged Please insert the power cord into special receptacle with rated voltage Be sure to use single phase three pins receptacle The earthing terminal of the receptacle must be earthed reliably If possible please adopt electric leakage protector The washing machine must be positioned so that the plug is accessible Be sure to pull the plug off and close the water faucet in following cases power failure delivering the machine setting the machine idle or cleaning the machine Do not plug or pull the power plug with wet hand Do not bend extend twist bind by force Do not press or nip it with weight Keep the pin of the power plug clean if the power plug is polluted with dust please wipe with dry cloth carefully If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard Do not let the machine share one receptacle with other electric appliances If the plugging into the receptacles loose do not use the plug any more O O O O O O O O O O In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet Ensure carpet does not obstruct the opening in the bases Do not put the machine at damp place like the bathroom Nev
7. User s Manual Haier Fully Automatic Washing Machine This manual is for HWM75 7288 Index e Safety precautions o Packing NSE caccasccececaenwsoestees e Names of the parts e Installation and adjustment e Preparation before WAS ING ssoccconssactcccaumneedasesess e Use the operation buttons e Disposal after washing e Trouble shooting Answer to QUeStiOn eneore Specification Please read this manual carefully before using Retain it for future reference 0030808632 Safety precautions Meaning and description of the symbols Contents marked with that symbol are related to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user WARNING Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety of the user FORBIDDEN Please check if power receptacle has good earthing condition before using to guarantee your Safety Please check if the water faucet is open and if the connection of the water inlet pipe is proper Itis suggested to use foamless washing powder Please don t use the washer in the environment below 0 C if the washer has been stored below 0 C please be
8. ect suitable water level The instant dissolving of the washing powder 1 Prepare warm water of 30 C and a container 2 Add the powder while stirring to fully dissolve it The quick program it is suggested to adopt liquid detergent instead of washing powder to guarantee the washing effect Put in the proper quantities detergent according to the water level and the laundries quantities It is suggested not to use high sudsing detergent Washing powder with poor quality or long time storage maybe caked Please pay attention to cleaning the detergent box in time Access for detergent How to use the softener Detergent box The usage and dose of the softener as per the specifications of softener Tum the e tub you will find a e s a softener inlet as the figure 1 open Rewer R the cover put the softener into the Figure 1 inlet as the figure 2 Before washing Ts close the cover and the softener will S27 F N i Access for softener N i i Al t th Uy drop into the inner tub during the We J Ss a last time rinsing La After the softener is put in please Bleach inlet don t place for a long time otherwise Open Close softener may solidify and cause Figure 2 flowing not smooth Don t put in the softener if the quick program is selected How to use the whitener Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub Avoid using whitener on laundr
9. er wash it with water Do not put wet laundries on the control panel Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning Wash the clothes that can float on the water surface easily please be careful especially for fear damage Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials Such as thinner petrol etc The children shall not approach the working washing machine Keep the machine away from direct sunlight and heat source like the heater Do not decompose repair or alter the machine by yourself Do not use water hotter than 50 C SES The ventilation F holes at the bottom Packing list Fully automatic Water inlet hose washing machine A TT Bottom plate Tapping screws User s manual One Piece Warranty card Names of the parts Top lid Detergent box Outer tub cover C Lint filter 2 pieces Balance ring Filter cover 2 pieces Pulsator Control panel film i Cabinet Adjustable foot 2 pieces Water absorption cushion All illustrations in this Manual are given for reference only Your products and accessories may show difference
10. etting you ii pep ed need to switch off the power and make new selection mi m Push bil button close the top lid Ifthe top lid is opened when the machine is spinning the machine will stop running and alarm 6 Finish washing After Finishing washing it will switch off power automatically 12 Disposal after washing Please first pull off the power plug from the receptacle before cleaning After using please clean the lint and foreign materials of the lint filter and overflow filter in time Otherwise it may influence your using the machine Clean the detergent box and set it on the control panel seat 1 The method of 2 The method of install dismantle Push it up install it upwards and aslant and gently aslant and push it in Ay Dismantle Install Cleaning the lint filter 1 Push down the spring Pull the back of the lint The back cover Up of lint filter filter and then you can S Y piece of the top lint filter Serie BES f to make the claws out of get down it off the front PSZ the filter cover and then cover of the lint filter oo yin pull out the lint filter to Sweep the rubbish in the The front cover get it down lint filter of lint filter Put the back of the lint filter into the front cover 3 Put the lint filter into filter 4 Make sure the lint filter cover and make it tight well installed or it can influence your use The filter screen of the water inle
11. g water e SPIN When the clothes are washed or the e The rinsing water level is one water level o r clothes are quite wet extra spin is needed E e TERT eee TE eT Oe ee eT ee ee ore Career re x Heed han a vee ies e e TUBDRY Drying the inner tub and the outer tub e maximal and man rated water level 7 which can avoid growing mildew 6690660065000 0000060600008 6646660646 6500604665600 4000600555 _ Steps of using the operation buttons 1 Push D button to switch on the power 2 Push C button to select suitable automatic program After the power is switched on SOAK is automatically set To select other fully auto program please push the PROGRAM button till the corresponding indicator is on Refer to the Program button on Page 11 When the soak is selected after the water start to jet the program wash rinse and spin will be implemented low water level soak for 25 minutes mid level 35 mins high level 45 mins Push PROGRAM button for 8 times and it will resume the initial mode It will circulate in that sequence Water pressure and water level influence the washing time Even there s no water in the tub the spinning will start after a certain period Wash and spin after putting the damageable clothes into tuck net to avoid scathe Wash the laundries that are prone to lose colors separately from other laundries When washing start or opening
12. ies with color or pattern as they are prone to lose color The whitener shall not touch the laundries directly Refer to the user s manual for the usage and quantity of the whitener For powder whitener please dissolve it before using Use the operation buttons Description of the function of buttons e e e020200200808080808080000080808088 8888888 8 Oe e eeeeneaeneneneoneseoeseoeee e088 8 G e e off Push the On Off button to switch on the J e a O On indicate the program about to run or indicate e ee e the selected mode or indicate the water level e When the power is on push itagainto gt QO Flashing indicate the running program S a ONEONE power _ l Push the On Off button to switch on Coeeceeeeeeeeeeeeeeeeeee00000 0 S H the power lf the start pause button is 7 oe ee not pushed the washing machine will e t displays during detecting e x automatically switch off the power t displays total remained time during the e e after 5 minutes e running program min D R tdisplays remained reserved time during ee eee a a a K reserve program hour ef 00CCCOHHCHCHCEHEHHHEEHHHOS Se e e It displays abnormal symbol in abnormal e e After the power is switched on press it to start e e situation See to Page 14 e gt the machine E SCeoeoeeeeeeeeeeneeeennenoneennece e During working push it to pause e oe eae
13. is needed please make separate purchase The inner diameter of the extra hose shall not less than 30mm and the length shall not exceed 1 5m 3 If the drain hose is too long cut it at mid point To make smooth drainage cut the front end of the hose slantingly 5 If the extra hose is too long cut it either at A or at B point Preparation before washing Connect the water inlet hose Open the water faucet Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle The earth terminal shall not link to gas pipeline and faucet water pipeline Put down the drain hose Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Pay attention to followings before washing the laundries Confirm if there is special requirement for the laundries T Clear the pocket Take out the coins sand hairpins etc LF A Tie the long strips fasten the buttons close zippers The quantity of the laundries shall not be too large Stretch and loosen the lt gt laundries before putting them in the tub RR When the pulsator is running the buttons of the laundries may cause noise ny For the sake of discretion please put the laundries with buttons into other KS laundries Check if the laundries are applicable for washing with machine e Please repair the damaged cloth before washing in order to avoid the situation
14. is slow the digital displays E4 The digitron displays E6 The Not wash machine does not act Not spin There s abnormal sound inside the machine The water tap leaks reserve procedure els the drain hose blocked els the drain hose put down eThe top lid is not closed eAre the laundries put slantingly els the machine slanting els the water tap opened or is there water supply failure els the water inlet valve blocked els the water pressure too low e The water level sensor is bad els there power failure els the power plug inserted tightly els the water level reached preset position els the power plug inserted tightly els the top lid closed reliably eAre the laundries set flat els the machine slanting eAre the laundries put slantingly in spinning eAre there any foreign materials els the jointer of water inlet hose loose or awry Clean the foreign material Open and close The top Lid Once Put down the drain hose Open and close the top lid once Close the top lid Reorder the laundries Close the top lid The machine will start running after 10 seconds of being placed horizontally Open the water tap Push the start Pause button once Clean the water inlet valve then push the start Pause button once Use after the water pressure is normal Please contact the after sales service department Please use it when there s power supply Insert the power
15. r installation position Dismantle the water inlet hose 1 6se the water faucet Locking lever 2 Press the locking lever Push down the slider Then pull off the water inlet hose Slider If the machine is used frequently the jointer of the water inlet hose can be kept on the faucet to prevent damaging the fixing screw How to change the direction of the drain hose 1 8mantle the back cover of the washing machine 2 Press the spring lamination lightly and pull the top segment of the drain hose decumbent then put Back cover down the drain hose from the drain hose frame Fain hose frame 3 Put down the drain hose squeeze the drain hose lightly and take off the hook put the drain hose into R the cabinet Take off the small baffle which installed on the other drain outlet and install it on the side Spring lamination which wont install the drain hose 4 Extend the drain hose from the other side and install it on the base by the drain hose frame 5 Install the back cover Remark In order to make sure of the correct of installation it is suggested to change the direction of the drain hose with our company serviceman Usage of the drain hose The drain hose shall drain smoothly 1 The height of the drain hose shall be less 2 Dnot trample or press the drain hose than 10cm or the drainage will not be smooth and cost such long time that the machine may stop at mid way 4 If extra drain hose
16. s from these illustrations due to our continuous improvement O OO Ss Bleach inlet Hanging hole Cabinet handle Screw cover right Adjustable foot film 2 pieces Screw cover left Water inlet valve Back control board Power line Back cover Drain hose Fixed foot 2 pieces Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the bottom plate After you open the package please lean the washing machine gently down on soft Front items like the towel cloth blanket ect Install the bottom plate to the bottom of g the machine then lift the machine up Back Y gently See to the figure Soft items sy j TIS Bottom plate Two claws at the bottom cover shall p be inserted in two bar shaped holes in the stand Make sure the claws are firmly in place Section enlarging Fasten the bottom plate to base frame with one screw Adjust the Installation position The washing machine away from wall should be overrun 20mm The largest allowable slope of the shank base of the machine is 2 The slanting or rough ground will result in unstable running or stoppage of the machine Please adjust it with following methods Confirm it s horizontal Hang the lead line to check if it is horizontal lt 2 Adjust the adjustable foot
17. t valve is likely to be blocked by foreign materials and influence the water inlet Please clean it with brush every two months If the cabinet is dirty wipe it with wet cloth Do not flush it directly with water Wipe it with neutral detergent Do not wipe it with thinner petrol alcohol etc After washing close the water faucet If needed you can dismantle the water inlet hose Do not store water in the washing machine for a long period Drain the water completely after each using Be sure to pull off the power plug before maintenance Hang up the power cord Wipe off the water drops on the surface of the machine and inside the tub Open the top lid for some time about 1 hour then close the top lid 13 Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself eThe top lid is opened during gt Close the top lid Phenomena The digitron displays EO The drainage cannot work or is too slow The digitron displays E1 It stops running in midway The digitron displays E2 The safety switch acts and the spinning cannot work The digitron displays E3 The water filling does not work or
18. t will notset amp STANDARD Common washing j e water level automatically You shall push o iF STANDARD program is set the o the start pause button to make new setting hi ill p 7 a ection the ifthere s water inside the tub the machine ee A A Ldetoctihe undi i d will disol o o computer will set the water level and ee Abi if ne Epari ae ie oma washing time as per the cloth and quantity e ai sa ay ee rea i ae o o of the laundries The whole procedure is e De ee ae under automatic control e set suitable water level by yourself e e SOFT eesoooocooooo Wahina he waden eiles eesooooooooooooooooooooo e e If quick program is selected it will display Rases aio WAO EM ENOT sc scadenssoacssocnies water level 24L e QUICK Posthaste wash of the laundry under 2 0 aa kg with light soil K go UT A PIATE EE Wae The noe level will automatically set 24L e e level will not respond E a scsyanscteyianeas 6 e During operation of wash and rinse e o WASH Just run the washing cycle without e program you can push down the water gt o gt drainage cycle The detergent was left level button to add water When you C inside the drum and can be recycled e e release the button or it reaches the e RINSE Remove the left detergent from the clothes e overflow water level the machine will stop and then rinse the Clotnes oes x addin
19. worse e Divide the laundries that are not colorfast from other laundries e Put those laundries difficult to absorb water into water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which can make it easier to remove the soil For those laundries that may get lint ball and those with long fur turn it over before putting in Do not put those laundries polluted by chemicals into the washing machine directly The foreign materials will result in damage of the machine 10 Put in the laundries The capacity of washing and spinning of he machine refer to the largest weight ofthe standard laundries under dry conditionthat can be washed or spinned in one time One time washing quantity shall be lower than the rated capacity The thickness size type of the cloth will influence the actual washing capacity It is suitable for one time washing to put in reasonable amount of laundries and the laundries can be turned round in washing Do not select the high water level for laundries less than 1 0kg so as to avoid splashing of water Putin the laundries J T Usage of the detergent How to use the washing powder Directly dissolved in the machine not applicable for fuzzy program 1 Fill small quantity of water 2 Add the powder Run for 30 seconds to dissolve it completely 3 Putin the laundries Sel
Download Pdf Manuals
Related Search