Digital Vacuum Regulator - J
Contents
1. Next hold in the key then while holding in the key press the M key until the value rLy appears in the display Let go of all the keys Press and hold in both the W and keys on the meter until the word tunE appears in the display then release both keys Press the A key once and the word bAnd will appear in the display Next hold in the key then while holding in the key press the Y key until the value 0 1 appears in the display Let go of all the keys Press the A key once and the word int t will appear in the display Next hold in the key then while holding in the key press the A key until the value 10 appears in the display Let go of all the keys Press the A key once and the word dEr t will appear in the display Next hold in the key then while holding in the key press the M key until the value 25 appears in the display Let go of all the keys Press the A key once and the word dAC will appear in the display Next hold in the key then while holding in the key press the A key until the value 1 5 appears in the display Let go of all the keys Press the 8 key once and the word CyC t will appear in the display Next hold in the key then while holding in the key press the VY key until the value on of appears in the display Let go of all the keys Press the 48 k2. 9 7 300 torr CH 2Cl2 99 7 Recovered 300 torr CH 2Cl2 100 torr CH 2Cl2 Test Conditions Buchi RE 111 evaporator equipped with a dry ice condenser Vacuum pump ultimate pressure 0 01 torr All tests were conducted using a 500 ml round bottomed flask at the pressure shown 3 5 Vacuum Requirements The type of vacuum source 1 e a high vacuum pump aspirator or in house vacuum system has no affect on the regulators operation or performance The only requirement is that the vacuum source be lower in pressure than the pressure you want to regulate the equipment at That is to achieve a vacuum or 40 torr in the attached equipment the vacuum source must be at least 40 torr The Digital Vacuum Regulator doesn t create a vacuum it only regulates the vacuum from an external vacuum source 3 6 Changing the Display Resolution The procedure below allows you to select the pressure display resolution of your J KEM vacuum controller This procedure allows you to specify 0 1 or 1 torr resolution Press and hold in both the W and keys on the front of the digital meter until the word tunE appears in the display then release both keys Press the W key until LEVL appears in the display Next hold in the key then while holding in the key press the 8 key until 3 appears in the display Let go of all the keys Press the key 11 times until vEr appears in the display Next hold in both the W and keys
3. Pressure Control for Research and Industry Digital Vacuum Regulator User s Manual Model 200 KEM Scientific Inc Instruments for Science from Scientists INDEX SECTION PAGE 1 QUICK OPERATING INSTRUCTIONS a oaoaooaoaoooo 3 KEM NET DATA LOGGING AND CONTROL SOFTWARE 4 2 REGULATOR DESCRIPTION 0 0 0 ene 5 3 OPERATIONS GUIDE 3 s lt 22 50e8e rad ava Avda chee ab eke Se 6 3 1 How the Regulator Works eee 6 3 2 Factors Affecting Vacuum Regulation Accuracy 6 3 3 Ramp to Setpoint amp Soak Feature eee 7 3 4 Use with Rotary Evaporators eee ene 9 3 Vac m Reguirements cai 2 cni steed esevd tt ecdeceedaaeadionen 9 3 6 Changing the Display Resolution 1 eee eee 10 3 7 Using the Regulator for Vacuum Distillations 10 3 8 Correcting Offset in the Displayed Pressure 04 11 Warranty J KEM Scientific Inc warrants this unit to be free of defects in materials and workmanship and to give satisfactory service for a period of 6 months from date of purchase If the unit should malfunction it must be returned to the factory for evaluation If the unit is found to be defective upon examination by J KEM it will be repaired or replaced at no charge However this WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of being damaged as a result of excessive vibration corrosive mate
4. aiting for an external signal When the signal is present then turn on my peristaltic pump to add reagents or as sophisticated as Open this valve then ramp my reaction pressure from 500 to 100 torr if 45 minutes hold for 2 hours then turn off regulation Contact J KEM for additional information Section 2 Regulator Description 7 Serial Comm Port on back os KEM Scientific p ene for Science from Scientists f l Off Full am m Vacuum n Pressure rr Meter Off Full Ramp to Jetpoint x _ Digital Vacuum Regulator Model 300 5 3 1 Pressure Display The default display is the pressure in the attached piece of equipment in units of mm of Hg torr The set point pressure can be seen any time by holding in the button 2 Control Key Pressing and holding this button causes the regulator to display the set point pressure as a blinking number in the display The set point pressure is entered by holding in the control key and simultaneously pressing the 4X button to increase or the W button to decrease the displayed value 3 Decreases V or increases A the set point pressure when the button is simultaneously held in 4 Regulators Power Switch 5 Indicates the position of the regulator selection switch 6 6 Regulator Selection Switch A three position switch that determines the pressure in the attached equipment see Section 3 6 The different switch po
5. alve in this position for future use Once the valve is set for a reasonable evacuation rate it doesn t require further adjustment KEM Net Data Logging and Control Software The USB port on the back panel of the controller is an interface to J KEM s KEM Net Software KEM Net is free and can be downloaded from J KEM s web site at www jkem com KEM Net provides remote control of up to 8 controllers graphical presentations of each digital meter and time amp pressure plots Highlights of KEM Net include GLP and GMP compliant data logging Runs a 12 step pressure ramp ES J KEM Sceitific KEM Net Control Your World Pre R File Logging Ramping About Logging of Time and pressure Logging of Power for Exo and Endotherm detection Program KEM IO Actions Section 3 10 Over amp Under pressure alarm functions KEM Net also includes a virtual comm port driver that provides a simple ASCII interface to operate and data log the controller from LabView or other software packages New Features GMP compliant data logging Exo and Enotherm monitoring KEM IO Remote Control of Laboratory Equipment based on Time and Pressure KEM IO is an optional feature that allows the controller to respond to inputs from instruments like a vacuum sensor or a hood door switch and also to control instruments like stirrers valves and chillers based on system pressure KEM IO automates programs as simple as Regulate at 500 torr while w
6. aporator The diagram at the right shows the result of using a needle valve a l 10 20 30 40 50 60 to limit evacuation rate Time Sec b Usea cold trap to condense volatile solvents At least one dry ice trap should be placed between the OUTLET of the digital vacuum regulator and the equipment being regulated This prolongs the life of both the regulator and the vacuum pump The dry ice trap available from J KEM catalog RCE1000 is highly recommended because of its high condensation efficiency large reservoir and ease of solvent removal 3 3 Ramp to Setpoint amp Soak Feature A new feature of J KEM s controllers called Ramp To Setpoint allows a specific rate for evacuation to be entered e g reduce the pressure to 20 torr at a rate of 10 torr Hour A second feature called Soak then lets you specify how long to stay at that pressure before turning off Example of Program Ramps Power Off 2 S 5 etpoint N A Power Off p 5 N Setpoint D A Time Time The controller is shipped with the Ramp to Setpoint feature OFF the user must specifically turn Ramp to Setpoint ON When Ramp to Setpoint is OFF the controller evacuates to the entered setpoint at the fastest rate possible 1 e the rate that results from fully opening the vacuum valve When Ramp to Setpoint is ON the controller evacuates at the user entered ramp rate The Ramp to Setpoint feature and its associated parameters are turned on a
7. d SPr to indicate that a SetPoint Ramp is active 2 Once the Ramp to Setpoint feature is activated in programming mode it will remain active until it s deactivated in programming mode Ramp to Setpoint feature remains active even if power is turned off to the controller Activating amp Programming the Ramp to Setpoint Feature I Press and hold in both the 48 and W keys on the front of the meter until the word tunE appears in the display then release both keys Press the M key 8 times until the word SPrr appears in the display This is where you set the ramp rate in units of torr hour First hold in the key then while holding in the key press the 48 or vy key until the desired ramp rate appears in the display then let go of all the keys Units are in torr hour i e mmHg hour Press the key once and the word SPrn will appear in the display This function turns the ramping feature ON OFF or to Hold First hold in the key then while holding in the key press the 8 or y key until the desired setting appears in the display then let go of all the keys Press the key once and the word SoaK will appear in the display This is where the soak time is set in units of Minutes A soak time of means to soak forever this setting is one below 0 First hold in the key then while holding in the key press the or y key until the desired time appea
8. d and accuracy better than this is usually not possible For display errors larger than 2mm the controller can be calibrated using the procedure below For users experienced with J KEM s meter do not correct pressure using the ZEro function This introduces an error not a correction Before beginning this procedure you will need to know the correct barometric pressure inside your lab This procedure should only be performed by a qualified electrician Remove the controller s cover 2 Plug the OUTLET port of the regulator and set the regulator selection switch to the FULL VACUUM position 3 Let the controller warm up for 30 minutes 4 Connect a vacuum pump to the INLET port turn it on and let it evacuate the controller to as close to O torr as possible Measure the pressure in the system using a manometer The regulator must be evacuated to as close to 0 torr as possible before the adjustment in step 5 is performed 5 Adjust the Zero pot until the reading on the meter matches the actual pressure 6 Turn the vacuum pump off and unplug the OUTLET port Adjust the Span pot until the meter reads the actual barometric pressure in the lab 7 Turn the controller off and replace the cover Looking in from the top of the vacuum regulator 11 III Resetting the Controller to Original Factory Settings J KEM manufactures the most technically advanced vacuum regulator available and should give you consist
9. ently flawless control If you have difficulty with your controller a good place to start to correct the problem is by loading the original factory settings If you still have difficulty with your controller our Engineering department will help you resolve the Press and hold in both the W and keys on the front of the digital meter until the word tunE appears in the display then release both Press the W key until LEVL appears in the display Next hold in the key then while holding in the key press the key until 3 appears in the display Let go of all the keys Press the A key until rSEt appears in the display Next hold in the key then while holding in the key press the key until the word All appears in the display Let go of all the keys This will clear the controller s memory and cause programming mode to exit Press and hold in both the W and keys until the word inPt appears in the display then release both keys First hold in the key then while holding in the key press the key until the value Lin3 appears in the display Let go of all the Press the A key once and unit will appear in the display Next hold in the key then while holding in the key press the A key until the value SEt appears in the display Let go of all the keys Press the A key once and the word SP1 d appears in the display
10. ey until the word SPrn appears in the display Next hold in the key then while holding in the key press the M key until the word OFF is displayed Let go of all the keys Hold in the key then while holding in the key press the key until 2 appears in the display Let go of all the keys Press the 48 key until diSP appears in the display Next hold in the key then while holding in the key press the until the value 0 10 appears in the display Let go of all the keys Press the 8 key until hi SC appears Next hold in the key then while holding in the key press the key until the number in the display reads 800 Let go of all the keys First hold in the key then while holding in the key press the W key until C appears in the display Let go of all the keys Press the 48 key and Addr will appear in the display Next hold in the key then while holding in the key press the until the value 1 appears in the display Let go of all the keys Press the 48 key and bAud will appear in the display Next hold in the key then while holding in the key press the key until the value 9600 appears in the display Let go of all the keys Press the A key and dAtA will appear in the display Next hold in the key then while holding in the key press the key u
11. for about 10 seconds until the display changes what the display changes to can be variable so just hold in the button until vEr goes away Press the or Y key until LoCk appears in the display While holding in the key press the A or Y key until NonE appears in the display Let go of all the keys Press the W key until LEVL appears in the display Next hold in the key then while holding in the key press the W key until 2 appears in the display Let go of all the keys Press the key 7 times until diSP appears in the display Next hold in the key then while holding in the key press the Y or A keys until 1 to select 1 torr resolution or 0 1 to select 0 1 torr resolution appears in the display Let go of all the keys Press and hold in both the W and keys until the pressure appears in the display then release both keys Pressure is now displayed in the selected units 3 7 Using the Regulator for Vacuum Distillations This model of J KEM s vacuum regulator is intended for medium accuracy vacuum applications such as rotary evaporators and vacuum ovens The DVR 200 regulates pressure with stability pressure variations from 0 5 to 2 torr as opposed to our high accuracy DVR 1000 regulator that controls variations to better than 0 1 torr Some vacuum distillations are not substantially affected by changes in pressure of 0 5 torr but many are This
12. let There should be no restrictions 1 e valves stopcocks between the Outlet port and the equipment you re regulating Best results are obtained when large diameter tubing is used to make this connection Turn the Regulator On J KEM Scientific Instruments for Science fro 1 Set the regulator selection switch to the P Off position Full v A i Vacuum 2 Ifthe unit is fit with a needle valve turn ee 1 545 al Meter Dff Full the valve until it s fully closed setpoint e e Digital Vacuum Regulator 3 Turn the regulator and vacuum pump on El u Regulator Selection Switch Enter the Desired Pressure The default display of the meter is the pressure in the equipment it s attached to The desired pressure or set point is entered by holding in the button on the front of the meter and simultaneously pressing either the W button to decrease or the A button to increase the set point The set point which appears as a blinking number can be seen at any time by holding in the button Move the Regulator Selection Switch to the METER Position When set to the Meter position the regulator maintains the attached equipment at the set point pressure entered in step 3 For Controllers Equipped with Needle Valves open the valve until the equipment is evacuated at a reasonable rate When at the set point adjust the valve for stable pressure regulation Leave the needle v
13. nd set in the controller s programming mode The parameters of importance are SPrr SetPoint Ramp Rate Allowable Values 0 to 9990 torr Hr This specifies the desired evacuation rate Note this parameter specifies the desired rate of evacuation Extremely high evacuation rates will not be maintained if the rate exceeds the capacity of the vacuum pump To minimize fluctuations around the setpoint a needle valve may be needed between the Digital Vacuum Regulator and the vacuum pump SPrn SetPoint Ramp Run Allowable Values ON OFF Hold This parameter turns the ramping feature ON or OFF During an active run if this parameter is set to Hold the setpoint ramp stops and holds at its current value This continues until the parameter is set to ON or OFF When set to OFF the values in SetPoint Ramp Rate and Soak Time are ignored SOAK Soak Time Allowable Values 0 to 1440 min This specifies the amount of time to soak at the setpoint after the setpoint vacuum ramp is complete A setting of causes the controller to remain at the final setpoint indefinitely A numeric value causes the controller to stay at the setpoint for the entered time and then turn power off to the vacuum valve The pressure in the vessel will increase depending on the number of leaks in the system Important Points to Know 1 While the Ramp to Setpoint feature in activated the display alternates between the current reaction pressure and the wor
14. ntil the value 18n1 appears in the display Let go of all the keys Press and hold in both the 4X or W keys until the pressure appears in the display then release both keys The word PArk in the display will go away when a set point is entered 12
15. r shuts the control valve preventing the vacuum pump from lowering the pressure any further The basic method of operation is very simple When the pressure in the equipment is above the set point the controller opens the control valve connecting the equipment to the vacuum pump and when the equipment is at or below the set point the controller shuts the control valve isolating the vacuum pump from the equipment o6pe eeu od Pressure Transducer 3 2 Factors Affecting Vacuum Regulation Accuracy a The rate of evacuation An important factor affecting stability is the rate the vacuum pump evacuates the attached equipment In some cases the rate of evacuation must be manually limited by using a needle valve A needle valve is used because many vacuum pumps have such high pumping capacities that they evacuate equipment faster than the controller can respond to changes in Pressure Regulation in a Rotary Evaporator pressure the controller needs 1 10 of a second to respond to pressure changes Particularly in small 700 equipment pressure can be lower more 800 Without valve than desired in 1 10 of a second 3 ouu without a needle valve limiting the 500 With valve evacuation rate Regulating the evacuation rate becomes more 6 400 important the smaller the piece of a w equipment being evacuated since it s evacuated faster for example consider 200 a 50 ml flask compared to a rotary j 100 ae aAa nA A ev
16. regulator is not recommended for small laboratory scale vacuum distillations J KEM does make a precision vacuum regulator the DVR 1000 which is designed and recommended for vacuum distillations Having said that the DVR 200 is not recommended for vacuum distillations we at J KEM suspect you may try it anyway so let us help you set the distillation up to deliver the best performance possible Points to follow 1 Connect a precision needle valve available from J KEM between the vacuum pump and the vacuum regulator Use a cold trap between the distillation set up and the vacuum regulator Close the needle valve all the way Turn on the vacuum pump set the desired vacuum setpoint in the DVR 200 and position the vacuum switch to the Meter position 4 Open the needle valve until the pressure in the flask decreases at a slow controlled rate that seems appropriate to the volume of the flask in use 5 Once at the desired setpoint adjust the position of the valve until pressure fluctuations are within an acceptable range for your distillation 6 The vacuum transducer in the DVR 200 looses some linearity below 12 torr The pressure reading will be consistent and reproducible but its absolute value may be off by as much as 2 torr 10 3 8 Correcting Offset in the Displayed Pressure A small amount of error can develop in the displayed pressure 2 torr of the vacuum regulator This is due to the wide pressure range of the transducer use
17. rials or misuse Components which wear or are damaged by misuse are not warranted This includes valves and fuses THERE ARE NO WARRANTIES EXCEPT AS STATED HEREIN THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL J KEM SCIENTIFIC INC BE LIABLE FOR CONSEQUENTIAL INCIDENTAL OR SPECIAL DAMAGES THE BUYER S SOLE REMEDY FOR ANY BREACH OF THIS AGREEMENT BY J KEM SCIENTIFIC INC OR ANY BREACH OF ANY WARRANTY BY J KEM SCIENTIFIC INC SHALL NOT EXCEED THE PURCHASE PRICE PAID BY THE PURCHASER TO J KEM SCIENTIFIC INC FOR THE UNIT OR UNITS OF EQUIPMENT DIRECTLY AFFECTED BY SUCH BREACH Returns requests for service and inquires should be directed to J KEM Scientific Inc 6970 Olive Blvd St Louis MO 63130 314 863 5536 Fax 314 863 6070 Internet Catalog http www jkem com E mail jkem911 jkem com 2 Section 1 Quick Operating Instructions Connect the Regulator to the Equipment Connect the vacuum pump or the vacuum source to the tube marked Inlet Note When the Digital Vacuum Regulator DVR is used on equipment smaller than a Rotovap a needle valve is needed for accurate regulation of pressure Place the valve on the inlet port see Section 3 2 Connect the instrument in which the vacuum is to be regulated i e rotary evaporator distillation setup etc to the tube marked Out
18. rs in the display then let go of all the keys If a soak time is set the controller display will alternate between showing the current reactor pressure and the word StoP when the soak time has expired to indicate that power has been turned off To exit programming mode press and hold in both the 8 and keys until the pressure appears in the display and release both keys Deactivating the Ramp to Setpoint Feature I Press and hold in both the 48 and W keys on the front of the meter until the word tunE appears in the display then release both keys Press the 48 key 9 times until the word SPrn appears in the display This function turns the ramping feature ON and OFF First hold in the key then while holding in the key press the 48 or y key until OFF appears in the display then let go of all the keys To exit programming mode press and hold in both the 8 and keys until the pressure appears in the display and release both keys 3 4 Use with Rotary Evaporators Your vacuum regulator is ideally suited for use with rotary evaporators To demonstrate the simplicity of the regulator the following example is given 1 Set the Regulator Selection Switch 6 to the OFF position and then turn on power to the DVR Turn on the vacuum pump 2 Enter a set point into the regulator appropriate for the solvent being removed for example 300 torr for CH2Cl9 3 Place the flask on the rotovap and move
19. sitions have the following effects Meter Evacuates the attached equipment to the set point pressure entered in the controller Off Isolates the vacuum pump from the attached equipment In this position the equipment can be opened to the atmosphere while the vacuum pump is running Full Vacuum Opens the regulator continuously to the vacuum pump independent of set point pressure The pressure in the attached equipment is lowered to the limit achievable by the vacuum pump 7 Optional serial port for remote PC control and data acquisition Warning J KEM s Model 200 Digital Vacuum Regulator should only be used with vacuums It is not designed to regulate pressures above atmospheric pressure Exposure to pressures above atmospheric pressure may result in damage to the regulator Section 3 Operations Guide 3 1 How the Regulator Works Outlet Inlet from equipment to pump The vacuum regulator consists of 3 important pieces The pressure transducer measures the pressure in the piece of equipment being regulated The Port close NN S process controller compares the pressure reading to middle from the transducer with the set point pressure i e the desired pressure entered If the pressure in the equipment is greater than the set point the process controller opens the control valve allowing the vacuum pump to decrease the pressure in the equipment When the pressure in the equipment equals the set point pressure the process controlle
20. the regulator switch from the OFF to the METER position When in the OFF position the regulator isolates the rotovap from the vacuum pump so the rotovap can be open to the atmosphere while the pump is running When placed in the METER position the regulator evacuates the rotovap to the pressure entered into the meter 4 When the majority of the solvent is removed move the regulator switch from the METER to the FULL VACUUM position When in the FULL VACUUM position the regulator ignores the set point pressure and fully evacuates the rotovap removing the last amount of solvent 5 When all the solvent is removed place the regulator switch to the OFF position and remove the flask Place the next flask on the rotovap and move the regulator switch to the METER position to begin the process again For the entire rotary evaporation process the only action needed is to change the position of the regulator switch The pump can run continuously and there s no need to change the set point pressure Solvent recoveries from a typical rotary evaporator are shown in the table below Solvent Recovery from Rotary Evaporators using J KEM s Digital Vacuum Regulator Bath Weight of Solvent Weight of Solvent Percent Time To Regulator Temperature Placed on Rotary Recovered from Solvent Evaporate Flask Solvent Set Point C Evaporator Rotary to Dryness Evaporator 475 torr 239 68 g 338 5 ml 238 66 g 99 6 400 torr CHoClo 466 68 g 352 2 ml 465 32 g 9
Download Pdf Manuals
Related Search