Vivotek FE8172 Quick Installation Guide
Contents
1. mm General I O Terminal Block Microphone In Pink Audio Out Green FA NOTE If DC power is preferred it should comply with O P 12VDC 1 5Amin L P S per IEC 60950 1 EN 7 English Power over Ethernet PoE When using a PoE enabled switch The Network Camera is PoE compliant allowing transmission of power and data via a single Ether net cable Follow the below illustration to connect the Network Camera to a PoE enabled switch via Ethernet cable r NOTE 1 This equipment is only to be connected to PoE networks without routing to outside plants 2 For PoE input use only UL listed I T E with PoE output Gow PoE Switch When using a non PoE switch Use a PoE power injector optional to connect between the Network Camera and a non PoE switch PoE Power Injector optional Non PoE Switch EN 8 6 Assigning an IP Address 1 Install Installation Wizard 2 from the Software Utility directory on the software CD 2 The program will conduct an analysis of your network environment After your network is analyzed please click on the Next button to continue the program 3 The program will search for VIVOTEK Video Receivers Video Servers and Network Cameras on the same LAN 4 After a brief search the main installer window will pop up Double click on the MAC address that matches the one printed on the camera label or the serial number on the2. if the dome cover does not come off easily Then follow the steps below to install the camera to either a ceiling or a wall Slide cover Z Release button If you plan to route cables from the side of camera re move the rubber slide cover from the dome cover EN 3 English Connecting Ethernet Cable amp the Power and IO Cable Connect the supplied power amp IO cables if your switch does not support PoE Connect the white header connectors to J6 and J7 on the camera Power amp IO Cable Connecting Cables If you need to route cables through the side opening proceed with the following 1 Connect the Ethernet and the Power amp IO cables The Ethernet cable is user supplied 2 Use an included cable tie to secure the Ethernet and IO cable to the base plate Insert the cable tie through the vertical mounting tab located on the edge of the cabling cutout 3 Make a clearance between cables and the vertical mounting tab Arrange the cables neatly to avoid getting in the way when the dome cover is attached 4 Cut the extra length from the cable tie If you route cables through a drill hole on a wall ceiling simply route cables through the cabling cutout Make a clearance between cables an the vertical tab Power and IO cables It is recommended to remove the strain relief boot if your Ethernet cable Strain relief boot Comes with one EN 4 Ceiling or Wall Mount 1 Attach the suppli
3. X VIVOTEK FE8172 ERE nora Quick Insraillation Guice English 4 P S38 I Fran ais Espa ol Deutsch Portugu s Italiano T rk e Polski Pyccku Cesky Svenska Dutch Dansk Indonesia y yall 5MP e 360 Surround View PoE gt SUPREME N Warning Before Installation oO Power off the Network Camera 5 Refer to your user s manual as soon as smoke or unusual for the operating temperature odors are detected 9 Do not place the Network 9 Do not touch the Network Camera on unsteady surfaces Camera during a lightning storm Do not insert sharp or tiny Do not drop the Network objects into the Network Camera Camera Package Contents FE8172 O Screws Anchors Cable tie O Alignment Sticker gt T TE eke aa Oy z s A Quick Installation Guide Warranty Card EN 1 English Physical Description o Inner View Lens Spring Contacts Contacts for Internal Microphone Ethernet 10 100 RJ45 Socket Header J7 r m Cabling Cutout Status LEDs Reset Button MicroSD SDHC SDXC Card Slot EN 2 o Outer View Dome Cover Built in Microphone AN IMPORTANT Record the MAC address under the camera base before installing the camera Hardware Installation _ First open the dome cover by pressing the release button You may squeeze the opposite edge of the dome cover
4. ed alignment sticker for the camera base to the a ceiling or wall 2 Using the circles on the sticker drill pilot holes into the ceiling Then hammer the supplied plastic anchors into the holes 3 Optional Drill a cable hole on the ceiling wall and feed the cables through the hole 4 Secure the camera base to the ceiling wall with the supplied screws NOTE You may also install the camera to a U S standard 4 in junction box You can align the camera s curved slots with the mounting holes on a junction box Use diagonal mounting positions on the camera to match those on a junction box EN 5 English Attach the Dome Cover Install the plastic dome cover by aligning the snap fit tabs on the dome cover with the slotted tabs on the camera base Install the dome cover by pressing it evenly to the camera base Make sure the dome cover and the base plate are flush aligned before pressing down The dome cover is secured using a snap fit mechanism Slotted tabs d Snap fit tabs EN 6 4 Network Deployment General Connection without PoE 1 Connect RJ45 Ethernet cable to a switch 2 Connect the power cable from the Network Camera to a power outlet 3 If you have external devices such as sensors and alarms make the connection from the general I O terminal block 3V3 Power 3 3V DC DO Digital Output D I Digital Input GND Ground Power Cord Socket Black gt
5. package box label to open a browser management session with the Network Camera 6 Ready to Use 1 A browser session with the Network Camera should prompt as shown below 2 You should be able to see live video from your camera You may also install the 32 channel recording software from the software CD in a deployment consisting of multiple cameras For its installation details please refer to its related documents VIVOTEK Mega Pixel Network Camera ws eem gt eet ope e Pasa ws FA NOTE If you encounter problems with displaying live view or the onscreen plug in control you may try to remove the plug ins that might have been installed on your computer Remove the following folder C Program Files x86 Camera Stream Controller EN 9 English P N 625018100G Rev 1 0 All specifications are subject to change without notice Copyright 2012 VIVOTEK INC All rights reserved VIVOTEK INC VIVOTEK USA INC 6F No 192 Lien Cheng Rd Chung Ho New Taipei City 235 Taiwan R O C 2050 Ringwood Avenue San Jose CA 95131 T 886 2 82455282 F 886 2 82455532 E sales vivotek com T 408 773 8686 F 408 773 8298 E salesusa vivotek com
Download Pdf Manuals
Related Search