User Manual
Contents
1. Cleaning the lid e Remove the bowl lid from the machine e Clean the surface using a damp cloth and Or a non abrasive sponge soaked in sanitising product e Rinse thoroughly using clean water Emptying the boiler Tank e Remove the drip tray e Remove the cap A Fig 31 e Place the machine on a flat surface e Place a container B with a capacity of more than 3 litres underneath the bleeder cap C e Use a coin or Allen wrench to unscrew the bleeder cap C e Pull out the cap C with a firm movement and wait for all the water to empty out from the boiler tank Fig 32 Cleaning and de scaling the Boiler Tank Warning The boiler tank needs to be de scaled on a regular basis e Follow the steps for draining out the boiler tank e Insert and secure the boiler tank bleeder cap e Fill the boiler tank with a solution of scale remover suitable for use in coffee machines and water following instructions supplied with the scale remover e Leave the solution in the tank for the time indicated in the scale remover instructions e Empty out the solution from inside the boiler tank e Rinse out the tank as per scale remover instructions Thermal Protector Switch If the Boiler tank boils dry the units thermal protector switch will activate to protect the heating element Allow to cool then reset as follows e Use a suitable tool to loosen and remove the protective screw A e Use a suitable tool to press the but2. taking care to grip it by the rotation pin Fig 15 e Place the bowl on a flat surface and using both hands remove the gasket by sliding it upwards in the direction shown by the arrow Fig 16 Wash the disassembled bowl and components with a sanitising detergent solution rinsing thoroughly with clean hot water Before reassembling the bowl ensure the gasket seal is positioned correctly Moisten the gasket seal with water and fit the bowl back into place DO NOT USE LUBRICANT Reassemble the bowl rod and mixing paddle by reversing the disassembly instructions Removing the tap e Ensure the bowl is empty e Move the tap rod to the maximum dispensing position Fig 17 e Press the button A securing the tap to the machine and then remove the tap with both hands Fig 18 Cleaning the Water Pan e With bowl and tap removed clean the surface of the pan using a damp cloth and or a non abrasive sponge Fig 19 e Clean the channel connecting the bowl and the tap using a cleaning brush included fig 20 e Refit the tap e Pour alittle water inside the pan e Use the tap to drain out all water from the pan so as to eliminate any small product residues inside the dispensing channel Disassembling and cleaning the tap To clean the inside of the tap disassemble it as follows e Remove the tap See removing the tap e Place the tap on a clean flat surface e Loosen and remove the screw A e Slide o
3. baixo assinado declaro que o equipamento anteriormente especificado esta em conformidade com a s anterior es Directiva s e Norma s Date Data e Date e Datum e Data e Fecha e Data 17 12 12 Signature Handtekening e Signature e Unterschrift pe Firma e Firma e Assinatura pre Full Name Volledige naam e Nom et pr nom e Vollst ndiger Name e Richard Cromwell Nome completo e Nombre completo e Nome por extenso Position Functie e Fonction e Position e Qualifica e Posici n e Fun o Commercial Director
4. e Normes e Normen e Standard e Est ndares e Normas A2 2008 EN60335 1 2002 A1 2004 A11 2004 A2 2006 A12 2006 A13 2008 EN62233 2008 EN55014 1 2006 EN55014 2 1997 A1 2001 A2 2008 EN61000 3 2 2006 EN61000 3 3 2008 IEC 62321 2008 LFGB 30 amp 31 Producer Name Naam fabrikant e Nom du producteur e Name des Buffalo Herstellers e Nome del produttore e Nombre del fabricante e Nome do fabricante Producer Address Adres fabrikant e Adresse du producteur e Fourth Way Anschrift des Herstellers e Indirizzo del produttore e Direcci n del Avonmouth fabricante e Endereco do fabricante Bristol BS11 8TB United Kingdom I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s Ik de ondergetekende verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande Richtlijn en en Standaard en Je soussign confirme la conformit de l quipement cit dans la pr sente a la aux Directive s et Norme s ci dessus Ich der die Unterzeichnende erkl re hiermit dass das oben angegebene Ger t der den oben angef hrten Richtlinie n und Norm en entspricht Il sottoscritto dichiara che l apparecchiatura di sopra specificata conforme alle Direttive e agli Standard sopra riportati El abajo firmante declara por la presente que el equipo arriba especificado est en conformidad con la s directiva s y est ndar es arriba mencionadas Eu o a
5. he machine malfunctions due to causes other than those listed or the proposed corrective actions do not solve the problem please call a Polar agent or qualified technician Technical Specification Capacity Dimensions Weight Modet voltage Power current Litres hxwxdmm kg asa o 580x410x200 230v 50hz Electrical Wiring This appliance is supplied with a 3 pin moulded BS1363 plug and lead with a 13 amp fuse as standard The plug is to be connected to a suitable mains socket This appliance is wired as follows e Live wire coloured brown to terminal marked L e Neutral wire coloured blue to terminal marked N e Earth wire coloured green yellow to terminal marked E This appliance must be earthed using a dedicated earthing circuit If in doubt consult a qualified electrician Electrical isolation points must be kept clear of any obstructions In the event of any emergency disconnection being required they must be readily accessible Compliance The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste To help prevent possible harm to human health and or the environment the product must be disposed of in an approved and environmentally safe recycling process For further information on how to dispose of this product correctly contact the product supplier or the local authority responsible for waste disposal in your area BUFFALO parts have underg
6. o carefully read through this manual Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product Pack Contents The following is included BUFFALO Hot Drinks Dispenser Instruction Manual Cleaning Brush BUFFALO prides itself on quality and service ensuring that at the time of packaging the contents are supplied fully functional and free of damage Should you find any damage as a result of transit please contact your BUFFALO dealer immediately Operation Filling the water boiler tank e Make sure the power switch is set to OFF e Remove the lid to the water boiler tank Fig 1 e Fillthe tank with water until it reaches the MAX fill line Fig 2 Filling the Bowl e Remove the lid and pour the beverage prepared according to the manufacturer s instructions into the bowl Fig 3 e Never exceed the MAX level mark e Replace lid e Turn on the power using the green switch Fig 4 Switch will illuminate when machine is on e Set the thermostat to the required temperature Fig 5 Dispensing the product Warning The products dispensed from the machine can be hot please take care to avoid risk of scalding e Place a suitable cup beneath the tap e Push or pull the lever on the tap until the required amount of product has been poured into the cup Fig 6 e Release the tap lever so that the product stops pouring e lf the product to be di
7. one strict product testing in order to comply with regulatory standards and specifications set by international independent and federal authorities BUFFALO products have been approved to carry the following symbol All rights reserved No part of these instructions may be produced or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of BUFFALO Every effort is made to ensure all details are correct at the time of going to press however BUFFALO reserve the right to change specifications without notice DECLARATION OF CONFORMITY e Conformiteitsverklaring e D claration de conformit e Konformit tserkl rung e Dichiarazione di conformita e e Declaraci n de conformidad e Declarac o de conformidade Equipment Type Uitrustingstype e Type d quipement e Ger tetyp e Hot Drinks Dispenser Tipo di apparecchiatura e Tipo de equipo e Tipo de equipamento Model Mod le e Modell e Modello e Modelo e Malli GF539 Application of Council Directives s LVD Directive 2006 95 EC Toepassing van Europese Richtlijn en e Application de la des directive s EMC Directive 2004 108 EC du Conseil e Anwendbare EU Richtlinie n e Applicazione delle Direttive e RoHS Directive 2011 65 EU Aplicaci n de la s directiva s del consejo e Aplica o de directiva s do Food Contact Directive EC 1935 2004 Conselho Standards EN 60335 2 15 2002 A1 2005 Standaarden
8. spensed is especially thick pull the tap Rod out to the maximum position Fig 7 e Any clogging in the dispensing line may be removed by sliding the tap rod back and forth Fig 7 Warning never touch the bowl or lid while the machine is operating since they are very hot always use the handle when moving the bowl lid Cleaning and Maintenance Emptying the bowl Before cleaning out the bowl it is first necessary to empty out any product inside it e With the machine switched on empty out all of the product still inside the bowl using the lever on the tap Warning the product dispensed from the machine has a very high temperature risk of scalding Removing and cleaning the bowl e Remove the lid Fig 9 e Slide the mixing paddle upwards to remove it keeping it in line with the central rod until the bottom slot of the mixing paddle is level with the rotation pin Fig 10 e Tilt the mixing paddle and slide it upwards as illustrated in Fig 11 to remove it completely Unlock the bowl clips as illustrated in Fig 12 to free the bowl from the machine body Release the bowl from the machine body using two fingers to prise it away from the fixed steel part of the mixer rod A and the others to grip the outlet edge of the bowl B Fig 13 Gradually pull the bowl harder until it comes away from its seating Slide the bowl upwards using both hands Fig 14 Slide the mixing rod upwards with one hand
9. sy Hot Drinks Dispenser UN Instruction Manual LTL Model Mod le Modell Modello Modelo Malli GF539 Saf ety Tips Position on a flat stable surface A service agent qualified technician should carry out installation and any repairs if required Do not remove any components on this product Consult Local and National Standards to comply with the following o Health and Safety at Work Legislation BS EN Codes of Practice Fire Precautions IEE Wiring Regulations Building Regulations DO NOT immerse the appliance in water or use jet pressure washers to clean the appliance Do not use the appliance for anything other than its intended use Always switch off and disconnect the power supply to the appliance when not in use Not suitable for outdoor use Keep all packaging away from children Dispose of the packaging in accordance to the regulations of local authorities lf the power cord is damaged it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance O O LO O Introduction Please take a few moments t
10. ton inside to restore normal machine operation Trouble Shooting Fault ProbableCause Does not heat No power Action Cu sure the machine is plugged in correctly Switch set to OFF Set the switch to ON Thermal Protector Switch has activated Reset Thermal Protector Switch Thermostat set to low Adjust the thermostat Mixing paddle does No power Make sure the machine is plugged in not turn correctly Mixing rod not fitted correctly Ensure mixing rod is correctly fitted Motor Fault Call Buffalo agent or qualified technician Switch setto OFF set to OFF Set Set the switchto ON switch to ON instructions Build up of debris Empty machine and clean tap as per instructions Sealing Gasket needs replacing Call Buffalo agent or qualified D FE from boiler Tank filled above MAX indication line Allow machine to cool then empty the tank and refill to correct level Sealing gasket needs replacing Call Buffalo agent or qualified MMMA FE Fault ProbableCause Action S Product leaks from The bowl is not fitted correctly Empty machine and re fit bowl as per bottom of bowl instructions Sealing gasket needs replacing Call Buffalo agent or qualified technician Machine shuts The water level in the boiler tank has Fill the boiler tank to max fill level and down while in use fallen below the minimum level reset Thermal Protector Switch No water in boiler tank Fill the boiler tank to max fill level and reset Thermal Protector Switch If t
11. ut the pin B and spring C from the seating e Pull the lever D all the way out from the knob E then push the lever F upwards from bottom until it comes out from the pin guide Fig 23 Unscrew the knob E by turning anti clockwise while holding the rod in place e Pull out the rod G and spring H from the tap body the pin gasket assembly I will slide out together with the rod Fig 24 e Detach the rod G from the pin gasket assembly 1 Fig 25 e Disassemble by pulling the pin L from the gasket M Fig 26 Wash the disassembled components with a sanitising detergent solution rinsing thoroughly with clean hot water Reassemble the tap by reversing the disassembly instructions e To fit the lever F push the rod D from the inside until the guides protrude the insert the lever F and slowly release the rod D Fig 27 e To fit the tap correctly back in place hold down the button making sure that the rod is completely extracted e Introduce the tap into the seat and push until the push button returns to its initial position Fig 28 Cleaning the Drip Tray The drip tray should be emptied and cleaned daily e Liftthe tray with grid and pull it outwards to remove it from its seating e Wash the tray and grid separately with warm soapy water e Dry all of the components and reposition the grid on top of the tray e Fit the tray back in place and press down to secure it to the machine
Download Pdf Manuals
Related Search