AW-8102 – Wired / Wireless Compatible Door/Window Detector
Contents
1. User Manual Installation Guide AW 8102 Wired Wireless Compatible Door Window Detector User Manual AW 8102 is Mini wired wireless compatible intelligent magnetic contact detector it has door or window open close instant detect alarm function smart mini design easy to match the installation environment cooperate with furniture decoration it has the higher sensitivity work with wireless alarm control panel within 200 meters via built in antenna wireless coding or enter the 9 digit address code with alarm control panel when magnetic stripe the distance over than 2 cm with transmitter it will send out the wireless alarm signal to alarm control panel immediately and it also built in the wired connection port so that work with wired control panel Features 1 adopted special micro power low consumption CPU Le osi 2 adopted unique multi code 3 Code 28 digit ID 8 digit function code 36 digit date code in Tamni total d 4 working status report automatically 5 open door or window indication 6 working voltage is 3 0V CR123A 3 0V Lithium Battery x 1 pc 7 current consumption lt 5uA static current emitting lt 15mA Magnetic Stripe alarm 8 wireless emitting frequency 433MHz 868M 9 wireless emitting distance 200m in open area built in Antenna 10 working temperature is 10 C 50 C 11 dimension is 80 32 24mm transmitter 74 20 12mm magnetic stripe ivory white color Installati2. contact pin keep one _ R pin open when magnetic stripe fix on the R place of reed switch the jumper jump to the R side of contact pin Wired Connection Coding Method iP when connect transmitter to wired alarm panel via wired terminal connection port _ keep two Irak wired connection port a tamper switch pins close E GEE BPO he l _ G _ r between detector and wireless alarm control panel detector on normal mode place the 1pc 3 0V lithium battery and LED light will flash 3 times alarm control panel on wireless coding mode please refer alarm control panel user manual press tamper switch or moving the magnetic stripe more than 2 cm with transmitter so that it can send out the wireless signal to alarm control panel if alarm control panel make the corresponding indicate sound it means match code successfully alarm control panel on manual coding mode enter the 9 digit address code to match this will be a higher probability of coding success Change Battery when detector sending the wireless signal LED light flash it means the low battery situation and detector also can sending the low battery alarm indication to alarm control panel CR123A 3 0V Lithium Battery pay attention to the anode and cathode Battery Testing After replaced the new batteries the detector will be in testing mode via LED light flash indicate for each triggering and dete
3. ctor will auto enter the normal mode after 5 mins and the LED light indicate will be switched off battery energy for power saving function
4. on Buzzer Don t install outside easy to Don t install on a unstable Don t install near strong break place base magnetic place 5 1 remove the transmitter cover you will see the inside PCB board 2 take out the PCB board the mounting frame is under the PCB board 3 hold the frame against the mounting surface and o O hey E PA S P AO r O R ET hed E Pre A T N mark the 2 drilling points through the mounting holes 4 drill the holes and fix frame to the wall using the screws with countersink heads which had packed in the package the 9 digit address code is under mounting frame put the PCB board back to the frame after installed on wall or other stable place 7 close the transmitter cover 8 attach the transmitter to the fixed mounting frame and the magnetic stripe to the movable part locate the magnetic stripe not more than 2 cm from the transmitter User Manual Installation Guide insert 1 pc CR123A 3 0V Lithium Battery on the battery tray pay attention to the anode and cathode and then LED light will flash 3 times so that make sure the battery had been connected Note if not drill on the door or wall please use strong double side tape or other strong bonding agent to fix the magnetic stripe and transmitter on the right place Magnetic Stripe Place keep one pin open when magnetic stripe fix on the L place of reed switch the jumper jump to the L side of
Download Pdf Manuals
Related Search