user manual
Contents
1. MOTOR der AR BIKE TO BIKE INTERCOM Main Features The MOTORader 4R Bluetooth Intercom System is a feature rich tool for motorcyclists by way of our exclusive wireless handlebar remote control now making using your intercom so much safer and easier This intercom system can be used for communication in 4 riders or between rider and pillion one rider can link with 3 riders and can choose any one person of the group to talk to at any given time Real full duplex wireless communication in 4 riders by hands free Bluetooth technology Other Features OONOOARWN Up to 900 meter talking range direct line of sight Up to 120Km h working speed Up to 7 hours talk time Safe auto receiving mobile phone calls Advanced A2DP amp EDR stereo Bluetooth profile with excellent audio quality Stereo music audio function transmits from A2DP enabled mobile phone MP3 GPS Line in 2 5 mm audio jack can connect with most audio sources Wind noise DSP cancellation Water resistance full weather Introduction de de the dhe Rider to par ROM Rider to pillion intercom Full duplex Full duplex i J wae B g9 Wired bluetooth enabled cell phone 3 P Boe S with A2DP profile Other audio devices Remote control on handgrip We will describe this communication kit as the R Remote C Control M Multifunctional I Intercom This RCMI can either be used for rider or for the pillion2. This RCMI is a multifunctional device for motorcyclists it can be used 1 As a hand free Bluetooth headset for mobile phone calls 2 As a two way wireless full duplex interphone in 4 riders or between rider amp pillion de ae ats Any rider could choose one of 3 riders to talk at a time The maximum communication range can reach 900m based on direct line of sight 3 As a wireless Bluetooth stereo music receiver and speaker This RCMI has EDR and A2DP profile with EDR and A2DP profile it can offer another important function listening to stereo music from A2DP enabled mobile phone MP3 or navigation audio instructions from a GPS this MP3 or GPS should have a built in audio Bluetooth transmitter 4 As the speakers of your MP3 GPS If your MP3 or GPS 1s not Bluetooth enabled and you do not have a Bluetooth AV dongle this RCMI also offers another method to listen to the stereo music audio info the simple wired method Plug the audio source directly into the RCMI via the 2 5mm 3 5 mm stereo connection cable Components of retail box RCMI headset main part RCMI 001 RCMI hand grip wireless remote control RCMI 002 Clip for mounting the main unit Speakers amp microphone amp audio plug RCMI 004 AC amp USB Charger AC110V 220V DC OUTPUT 5V RCMI 005 2 5mm to 3 5mm audio adapter cable q RCMI 006 Main RCMI communications unit VOLUME RESET RIDER A PHONE PLAY ON OFF RIDER B
3. VOLUME RIDER C Wireless Handlebar Remote Control Operation The remote control has its own replaceable battery lasting 2 3 years You do not need to turn the remote on or off once a button is pushed it will automatically activate this function Press the selected button once only and not repeatedly as this will confuse the main RCMI unit There will be a 3 5 second delay once the selected button is pushed before activation RIDER A i PHONE PLAY RIDER B RIDER C VOLUME VOLUME Clip amp hanging hole for mounting the main RCMI unit Clip Inserted plate Spacer Speakers Boom Microphone audio plug N Q The AC amp USB Charger Before using Charging the RCMI Before using this device please charge the RCMI main device at least three hours 1 Insert the 2 5mm plug of the charging cable into the small charging jack of the RCMI you can either charge by AC adapter or computer 2 While charging the red LED on the headset module will illuminate when the charging is finished the red LED will extinguish Note if you do not use the RCMI for a month or more to protect the Poly Li battery please charge the RCMI at least every month the fault damaged by wrong charging will be not guaranteed Attaching and removing the RCMI main unit on your helmet With the clip you can easily mount the main unit of the BIM on a helmet within 3 minutes Step 1 Find the best position on the left side o
4. the blue LED of unit A will flash Power on unit C the blue LED of unit C will flash Simultaneously hold the C key on unit B and hold the B key on unit C until the red amp blue LED of the both pairing RCMI s flash short press the C key on unit B 5 9 seconds later the red LED of both RCMI s will extinguish and the blue LED then will flash briefly every 2 5 seconds thus they have finished the pairing process now you can talk to each other Pair unit D with unit A B C 2 4 Pair unit D with unit A Because there is not D key on the RCMI the way of pairing unit D with unit A B C is different To be sure that unit B and C is in status of power off Simultaneously hold the A key on unit A and hold the A key on unit D until the red amp blue LED of the both pairing RCMI s flash short press the A key on unit A 5 9 seconds later the red LED of both RCMI s will extinguish and the blue LED will flash briefly every 2 5 seconds thus they have finished the pairing process now you can talk to each other 2 5 Pair unit D with unit B Be sure that unit A and C is in status of power off Simultaneously hold the B key on unit B and hold the B key on unit D until the red amp blue LED of the both pairing RCMI s flash short press the B key on unit B 5 9 seconds later the red LED of both RCMI s will extinguish and the blue LED then will flash briefly every 2 5 seconds thus they have finished the pairing process now you can talk to eac
5. the intercom functions by the A B C button of the remote control please don t press the same button repeatedly There will be a 3 5 second delay before connection Initiate an intercom call For example A short press lt 1 second of the B Key then promptly release your hand you will hear a beep di then wait about 3 5 seconds and you can now talk with rider B If you then you short press the C key it will change the communication to talk with rider C RIDER A i 2 PHONE PLAY RIDER B RIDER C VOLUME VOLUME Tips Talk with unit D Because there is not D key on the unit the way of calling unit D 1s different Short press A key on unit A and you will connect with unit D Short press B key on unit B and you can talk with unit D Short press C key on unit C you will talk with D Finish an interphone talk You only need a short press of same unit of an intercom A B C key to terminate communication Note to reduce power consumption when you do not need to talk don t keep your RMCI in the intercom state Note If two RCMI s were out of range they may lose connection When you come within range again you only need to initiate a intercom call as normal Music Audio function 1 Listen to audio navigation from your GPS with a built in Bluetooth transmitter a Pair GPS with your RCMI Be sure that you have turned off the Bluetooth function on your mobile phone Be sure
6. ey on the RCMI You must place the RCMI in Pairing mode this is done by way of holding down the Power Interphone key on the headset until the red amp blue LED flash alternately Begin the searching for Bluetooth device on your mobile phone according to the phone s instructions When the RCMI is discovered the mobile phone will display MOTOR PHONE select this and accept the connection Your mobile phone will ask you to input a password to enable this connection when prompted input password 0000 four zeros Your phone will confirm that pairing has succeeded Note that the only light showing on the headset is now blue and it will flash once every 5 seconds Turn on Short press lt 1 second Reset key on the RCMI Press the Power RIDER A key for 6 seconds or so until the blue light illuminates promptly release the Power Interphone key then the blue led light will flash every 2 5 seconds and you can see that on the screen of your mobile phone the RCMI will ask your phone to connect with it select yes on your phone Increase the volume Short press of the V key Reduce the volume Short press of the V key Safe mobile phone call function 1 Receive a phone call automatically With an incoming a phone call you will hear the ring on the mobile phone and about 3 5 seconds later the RCMI will receive the call automatically 2 Terminate phone call When you finish talking on the phone a short p
7. f your helmet to put the clip 2 Insert the inserted plate between shell and foam of the helmet Fix the clip on the helmet with the screws 3 Hang the main unit of the RCMI on the clip Aa Clip fixed on helmet RCMI mounted on a helmet Note 1 If the shell of your helmet is a little thick you could put the Spacer between the clip and the inserted plate 2 There are some helmets that the shell is very thick maybe it is difficult to fix above clip on these helmets In this case you could use below clip with the 3M tape Attaching the two speakers and the microphone The success of the system depends on the careful positioning of the speakers directly over top of the ear canals This will give the best signal of noise of the received audio 1 To find the position of your ear canals put your helmet on firmly but don t do it up Slide your thumb of one hand up between the inside of the helmet and your ear with the fingers of that hand on the exterior of the helmet Feel the ear canal in your ear with your thumb and then grip the helmet firmly between thumb and fingers of that hand carefully take the helmet off BUT don t move your thumb from its position inside the helmet Look at where your thumb 1s this place marks the centre of the ear speaker 2 Remove the protective backing of the Velcro and mount the Velcro pads in the correct positions attach the two speakers on the Velcro inside your helmet the speaker with short wire c
8. h other 2 6 Pair unit D with unit C Be sure that unit A and B is in status of power off Simultaneously hold the C key on unit C and hold the C key on unit D until the red amp blue LED of the both pairing RCMI s flash short press the C key on unit C 5 9 seconds later the red LED of both RCMI s will extinguish and the blue LED then will flash briefly every 2 5 seconds thus they have finished the pairing process now you can talk to each other To get all pairing details please refer to below pairing chart WHEN RED AND BLUE LED FLASH PAIRIN STATUS INTERPH ON BOTH lt pair each INTERPHO aie G BEFORE ONE UNITS SHORT other gt BUTTON PAIRING PRESS BELOW PAIRING BUTTON ON LEFT UNIT lt pair each ne powered on powered on lt pair each ene powered on lt pair each other gt lt pair each other gt lt pair each other gt lt pair each other gt powered on powered on powered on 3 Choose which rider you will talk with Pairing these riders seems a bit complicated but using the intercom is very simple After you have paired all the RCMI s you can now talk with one of the riders at a time STEP After finishing the pairing procedure confirm that all of RCMI s have been powered on We suggest that it is best to use the hand grip remote control to initiate or finish an intercom call this is a safer method whilst riding Note When you are operating
9. ing all RCMI s Before pairing to avoid being confused please stick respectively 4 labels of A B C D on 4 main units of the RCMP s Note At one time it only allows one RCMI to pair to another RCMI so when you are pairing two RCMI s please confirm the other units are in status of power off 2 1 Pair unit A with unit B Power on unit A the blue LED of unit A will flash Power on unit B the blue LED of unit B will flash Simultaneously hold the B key on unit A and hold the A key on unit B until the red amp blue LED of the both pairing RCMI s flash short press the B key on unit A 5 9 seconds later the red LED of both RCMI s will extinguish and the blue LED will flash briefly every 2 5 seconds thus they have finished the pairing process now you can talk to each other 2 2 Pair unit A with unit C Be sure that unit B and unit D is in status of power off Power on unit A the blue LED of unit A will flash Power on unit C the blue LED of unit C will flash Simultaneously hold the C key on unit A and hold the A key on unit C until the red amp blue LED of the both pairing RCMI s flash short press the C key on unit A 5 9 seconds later the red LED of both RCMI s will extinguish and the blue LED will flash briefly every 2 5 seconds thus they have finished the pairing process now you can talk to each other 2 3 Pair unit B with unit C Be sure that unit A and unit D is in status of power off Power on unit B
10. ord for left ear the speaker with long wire cord for right ear Adjust the position of the microphone Note To reduce the external noise you need to close the visor while riding and please adjust the position of the microphone to be right in front of your mouth with the foam just touching your lips the visor should cover the microphone effectively Minimizes wind noise contribution Correct position of the microphone Wrong position of the microphone Operation The operation is friendly and very easy Pairing with your Bluetooth phone for the first time Note You must have a Bluetooth enabled phone to Pair with the RCMI Before using the 6RMI please familiarize yourself with Bluetooth function of your mobile phone Read the instruction manual that came with the phone so you can enable its Bluetooth function Before you can use this RCMI in combination with your phone you will need to pair it with your cell phone for the first time This usually only needs to be performed once with that individual phone however follow the instructions supplied by the phone manufacturer and save the pairing so it will be automatically connect when your phone and the RCMI come into contact A 1 2 3 4 5 6 Please pair the RCIM with the phone only by the buttons of the main unit Don t pair them by the remote control Enable the Bluetooth function on your mobile phone Short press lt 1 second Reset k
11. ost MP3 players Play the MP3 you can listen to the music via the speakers of your RCMI NOTE You only can adjust the music volume on your MP3 5 Listen to navigation instructions from your GPS by wired method The same way of listening to music from a MP3 6 Listen to stereo music from MP3 via external audio Bluetooth transmitter If you have a external audio Bluetooth transmitter insert the plug of the transmitter into the jack of the MP3 Pair the transmitter with the RCMI according to the instruction manual of the transmitter 7 Listen to stereo music from MP3 with a built in Bluetooth transmitter Please familiarize yourself with the Bluetooth function of your Bluetooth enabled MP3 this MP3 must have Bluetooth transmitting function Read the instruction manual that came with the MP3 so you can enable its Bluetooth function Pair the MP3 with the RCMI according to the instruction manual of the MP3 8 Auto switch between different operations Whilst talking on the intercom or listening to music if you receive a phone call the voice will be switched to mobile phone talking state automatically After the call has been hung up the system will auto return to intercom talking or music playing state While listening to music short press any intercom key and it will initiate intercom talking After terminating the intercom talk the system will return to the music automatically Note It will take 3 5 seconds to return to intercom
12. ress of the Phone Play Key will terminate the call 3 Reject a phone call When you receive an incoming phone call you will hear the ring within 1 second immediately press the Phone Play key and it will reject the call Set up for bike to bike and rider to pillion intercom pairing Pairing is a one time process that is required for mutual recognition between a RCMI and other RCMI Once the two headsets are paired they will retain paired whenever they are within range Please note that you can speak via intercom to one persons headset at a time Note B When you are pairing two RCMIs you must keep other RCMIs in the off status C Please pair the RCIMs only by the buttons on the main unit Don t pair them by the remote control D You can pair your RCMI with maximum total of four RCMI s 1 Pairing two RCMIs If you only need to communicate with one person rider to pillion or bike to bike you can simply pair two RCMIs according to the below steps Power on RCMI A the blue LED of RCMI A will flash power on RCMI B the blue LED of RCMI B will flash Simultaneously hold the B key on RCMI A and hold the A key on RCMI B until the red amp blue LED of the both pairing RCMI s flash short press the B key on RCMI A and 5 9 seconds later the red LED of both RCMP s will extinguish and the blue LED will then flash briefly every 2 5 seconds thus they have finished the pairing process now you can talk to each other 2 Pair
13. talking state after the mobile phone talking has been hung up Troubleshooting 1 Not working Could be a flat battery charge the RCMI for 3 hours 2 Reset In some regions of high RF strength 1 e near high power TV transmitters GSM station or airport radars these can overwhelm the CPU in the BIM causing it to latch up Short press lt 1 second Reset key on the RCMI When you turn on the RCMI it will work normally again 3 No sound Physically check to see the headset cables are ok or the audio plug is properly inserted into the jack Swap with the other functioning RCMI to localize the problem Have you turned the volume too low 4 Whistling of the speakers If the microphone is too close to a speaker the speaker will make a whistling noise take the microphone away from the speaker reduce the volume by the Volume key it will resolve this issue 5 Lose connection with your mobile phone or music from the mobile phone Thankyou for choosing the MOTORader 4R Bluetooth Interphone Communication Headset
14. that the RCMI is in the state of power off Refer to your GPS instruction booklet for Bluetooth pairing process When the GPS is ready for pairing long press the POWER Rider A key on the RCMI until the red amp blue LED flash Several seconds later the GPS and the RCMI will have finished the pairing process 2 Listen to stereo music from your A2DP enabled mobile phone Read the user manual of your mobile phone carefully if your mobile phone is A2DP enabled the RCMI can receive the stereo music from your mobile phone Please note that only A2DP stereo Bluetooth enabled mobile phones can offer a Bluetooth music transmitting service You can use the Phone Play key to pause play the music from A2DP Bluetooth devices 3 Listen to music from some mono Bluetooth enabled mobile phones Almost all current Bluetooth enabled mobile phones can offer Bluetooth music transmitting service We do not promise that the RCMI will support music function for all Bluetooth enabled mobile phones Step Confirm that your RCMI has paired with your mobile phone play the music on the phone and then you can enjoy the music on your RCMI Note For mono Bluetooth mobile phones you can not use the Phone Play key to operate the music you can only operate the music on your phone 4 Listen to stereo music from your MP3 by wired method 2 5 3 5mm audio adapter cable With the 2 5 3 5mm audio adapter cable attached it can be used for connecting your RCMI with m
Download Pdf Manuals
Related Search