User manual ver. 1.53
Contents
1. General set up 1 Mount the fixture in the required position The integral yoke can act as a floor stand or hanger Important e When suspended off ground always use a safety wire rated to a minimum of 1 1kg 25lbs around the yoke e Do not position the fixture close to fog machines The fog oil mist will be drawn in by the cooling fan and will short out important components The warranty will be void for all fixtures returned in such a condition 2 Where external control is to be used connect a DMX lead XLR 5 pin female to the input socket at the rear of the fixture 3 Where other fixtures are to be used in a control daisy chain con nect a DMX lead XLR 5 pin male to the output socket at the rear 0 e fixture EE se DMX out XLR Spin female socket ol XLR 5pin male socket 4 Connect power to the fixture using a Neutrik PowerCon connec tor Insert the connector and twist it clockwise until it clicks into place Important e When daisy chaining fixtures do not exceed a total load of 3kW in a single daisy chain subject to supply and cabling restrictions Maximum power requirement per fixture 66 watts See also the Start up peak note on page 4 Power out socket Neutrik PowerCon NAC3FCB connector required Power in Fuse holder socket on underside see page 4 for details Neutrik PowerCon NAC3FCA connector 5 Use the control panel to2. 216 223 27 Static light blue 224 231 CH Static purple 232 239 29 Static red PixelLine Micro 240 247 38 Static green personalities are 248 255 31 Static blue available for a variety of controllers For details go to www pixelrange com The table below shows how colour mixing chase effects and master intensity controls are mapped to DMX channels for each mode The diffi dit T and tibT modes do not use chase effects In all modes the first channel of the fixture occurs at the DMX address selected using Add and successive channels for the fixture follow from there Note The PERS gt FES option determines the number of channels to use in dfti dMiT amp 1BbT modes iBbT uses twice the number of channels setup within PES Channel AM SMT AM N AMAT fbb T 6bT Mie RES 3Ch RES 4Ch RES 3Ch RES 4Ch 1 Red Amber Red Red Amber course Red course Red 2 Green Green Red Amber fine Red fine Green 3 Blue Blue Green course Green course Blue 4 Master int Amber Green fine Green fine Amber 5 Master int Blue course Blue course E 1 Effect 6 Blue fine Blue fine C 1 Speed 7 Master int Amber course E 1 Xfade 8 Amber fine Ce Effect 9 Master int Cg Speed 10 Ce Xfade 1 Master int Master intensity for dit dit T and 1ibT modes are available only when the PERS gt MINT option is set to oN course High channel for 16 bit fine Low channel for 16 bit Master slave data indication The right hand deci
3. exit the menu completely Channel layouts within operation modes This section describes each of the 31 internal chase effects that are selectable either via the control menu PRob gt C 1 Ce gt EFEC or using DMX values sent from an exter nal source To use the internal effects set the ModE option either to EF M to control effects via the menu or EF d 4 E to control effects externally via DMX See page 4 for details about controlling effects on other fixtures via DMX without using a control desk DMX EFEC Chase effect description value value 0 7 oo Off 8 15 814 Rainbow chase forward 16 23 Bg Rainbow chase reverse 24 31 83 10 90 duty cycle strobe white 32 39 BY 10 90 duty cycle strobe white 40 47 BS 10 90 duty cycle strobe white 48 55 BBE 50 50 duty cycle strobe white 56 63 BI 50 50 duty cycle strobe red 64 71 88 50 50 duty cycle strobe blue 7279 B9 50 50 duty cycle strobe yellow 80 87 12 50 50 duty cycle strobe green 88 95 14 Pulse strobe white 96 103 2 Pulse strobe blue 104 111 13 Pulse strobe rainbow 112 119 1H Pulse strobe red green blue 120 127 15 Primary secondary chase 128 135 6 Rainbow chase 136 143 11 Yellow blue chase 144 151 8 Rainbow chase 152 159 19 Yellow blue chase 160 167 28 Red blue chase 168 175 Red green chase 176 183 2 50 50 duty cycle fade red 184 191 23 50 50 duty cycle fade green 192 199 4 50 50 duty cycle fade blue 200 207 25 Static orange 208 215 2B Static yellow
4. a television cameras Neutrike PowerCon NAC3FCA connector wiring Neutral Note e To optionally clear all previous settings At the rear panel press the middle two buttons and while the cur rent address and mode are being displayed The four digit display will show FACT then SET to indicate that the fixture has been returned to its default condition Menu operation General notes e Ensure that only one DMX device in the chain is set as master e g the lighting desk This fixture is usually set to slave mode e This fixture is shipped with the DMX address set to og 1 e The four digit display can be set to switch off when not in use To restore press To alter this mode use PERS gt dISP Chase effects Refer to product manual for proper operating instructions Using the menu e When not in the menu the four digit display scrolls the current DMX address and mode The display s right hand decimal point data dot is used to indicate status see below e Press to enter the menu The four digit display will show AddP e Use and to move between menu options or to change a value within an option e Press to enter an option or to fix a changed value within an option and return to the previous option level Note If you do not press to fix a value operation will revert to the previously set mode at the next power on e Press to exit from a menu option and eventually
5. access the internal menu and choose the appropriate operation mode and related settings see over When suspended off ground always use a safety wire rated to a minimum of 11kg 25lbs around the yoke Operation modes The PixelLine Micro Wash provides a range of operation modes These are selected using the ModE section of the control menu cif Allows RGB A control via DMX input Using the PES resolution option you can determine the number of DMX channels required either 3 or 4 channels Internal chase effects are not available within this mode MANI Provides RGB A colour mixing independently of any external control Use the internal control menu MAN section to select the required colour values EF g Allows the control of the dual internal chase effects via external DMX input EF 4 Allows the display of the dual internal chase effects independently of any external control Use the internal control menu PFabG section to select the required chase effects speeds and cross fades 4f Provides control of RGBA mixing and selection of the dual internal chase effects via DMX input Requires 11 DMX channels ty T Allows RGB A control via DMX input using two 8bit channels per colour The RES option determines whether 6 or 8 channels are required Internal chase effects are not available within this mode fh T Operates as per di mode but uses an alternative dim ming curve to produce better results when viewed vi
6. er and fuse 4 3 e If live DMX is connected the right hand decimal point on the display should flash if not check the DMX Weight cable and the desk output Fixture and yoke 2 1Kg 4 6lbs Check that the selected ModE matches the desk person ality being used The master intensity channel for the current mode may Power Input voltage 90 to 264V AC 47 to 63Hz autosensing be set at zero For dit or 1bbT modes check the Earth leakage 0 12mA setting of PERS gt MINT Connectors Neutrik PowerCon see first page for details e Ensure that only one DMX device is set as master Power requirements 230V 50Hz 115V 60Hz e Standalone chase effects Effects programmed using Standby 2 watts 2 watts PRoG gt L 1 and Ce but the fixture is not in ModE gt Mes 66 66 EF M mode Check also that PRobD gt LEVL is not set aximum const wans wants at zero Start up peak lt 40 amps lt 20 amps Standalone RGB mixing Colour values set within MAN section but the fixture is not in ModE gt MANU mode Fuse access T fi he single fuse is located on the underside panel of the xture To remove the fuse Using a flatblade screwdriver push down the fuse cap a h nd then twist it anti clockwise until it disengages from the older Fuse type 20mm 2A T2AH anti surge ceramic body Documentation by Corporate Text amp Design www ctxd com Release 1 53c Approvals Miscellaneous Enclosure rating Co
7. ermines the intensity of the four digit control panel display Values range from O dimmest to 15 brightest When set to HafF the control panel display will blank out shortly after the menu is exited The master slave DMx signal indication will remain active Cc 3 i La Ly jaz faz aD a tot to C z aol S ER E dM v 8bit RGB A control using the number of DMX channels determined by PEPS gt PES PERS gt MINT set to aN provides a master intensity No chase effects are selectable Displays the resulting RGB levels that are set via the MAN section of the internal menu When set as master these levels are also output via DMX for the control of other fixtures Chl to 3 L 1 Effect Speed amp Xfade Ch4 to 6 Ce Effect Speed amp Xfade Ch7 Master intensity Al amp ID o Displays the chase effect s determined within the PPob section When set as master these levels are also output via DMX for the control of other fixtures DMX Ch1 to 4 RGBA Ch5 to 7 L 1 Effect Speed amp Xfade Ch8 to 10 Ce Effect Speed amp Xfade Ch11 Master intensity Em e ER m m Ee 16bit RGB A control using 2x the number of DMX channels determined by PERS gt PES PERS gt MINT set to aM provides a master intensity No chase effects are selectable aa Es amt Operates as per dit mode but uses an alternative dimming curve to produce better results when viewed via television cameras gt lt a
8. l Using master mode to drive other units Specifications This unit can control any number of other Pixel Range fix tures via DMX links without the need for a control desk Dimensions Set this unit as master PERS gt dATR gt MAST and ensure all others are set to slave PERS gt JATA gt SLAV Connect all fixtures via DMX daisy chain Set slaves to ModE gt lt or dl T Set the master to either e ModE gt EF Mand use PFab to choose effects or e ModE gt MANU and use MAN to choose colour mix Use Add gt cll to set slave addresses the master unit s DMX address is ignored e Effects 18 cells are output in groups of 3 DMX channels to give RGB values per cell 54 channels in total Set the address of each slave fixture according to which of the 18 cells you want them to appear within or to begin with for multi cell fixtures HBB 1 for cell 1 RABY for cell 2 ABSE for cell 18 Set RGBA slave fixtures to 3 channel mode using PERS gt RES gt JCh e Colour mix Set slaves to any addresses on 4 channel boundaries e g ABH 1 ABOS ABBY REHE Troubleshooting Fixture remains at blackout when illumination expected Note The dimensions shown above relate to the main fixture body The yoke knob extends 10mm 3 8 beyond the stated width m 150mm 57 3 of the fixture e If the display panel is not showing any indication even ae after a button press check the input pow
9. mal point data dot of the display is used to indicate the mas ter slave settings and also the presence of a DMX input signal as shown below Data dot ON Master mode Data dot FLASHING Slave mode DMX data input present Data dot OFF Slave mode no DMX data present Notes e Ensure that only one DMX device in the chain is set as master e g the desk e Use PERS gt dATA to change between master and slave modes e When set to master mode the fixture will scroll MASTER in place of a DMX address when not within the menu e If the display has been set to auto off dT SP gt HaFF the data dot will remain active but at a lower brightness 7d mq Eh Menu contents Sets the base DMX address from which the control channels will begin BE m Eg S gt lt ES io P CJ Em Ea ES A LJ Shows the installed revision of the main fixture firmware This is for information purposes only no changes are possible within this option Shows the installed revision of the software used to control the four digit display panel This is for information purposes only no changes are possible within this option Selects the primary internal chase effect See Chase effects for descriptions Select ModE gt EF M to show the selected chase g Cy Cy inl La SK mM ae ie ina mM ja mM 0J OJ M Cy icy g C C3 C C WwW Selects the cross fade speed between the steps of the selected C 1 chase effect Selects the speed
10. ntrol input Gia RANGE sales pixelrange com The peak value occurs only at first power up and lasts only for a period measured in micro seconds Adjustments may need to be made to supply circuit breakers when multiple fixtures are daisy chained causing them all to draw the peak simultaneously CE IP20 not protected against moisture ingress USITT DMX512 input connector pin out below PIN 1 PIN 5 Not used PIN 4 Not used salesUSA pixelrange com
11. of the selected C 1 chase effect Selects the master intensity level of chase effects C 1 and C2 ma r gt rJ LA un Selects the secondary internal chase effect See Chase effects for descriptions Select ModE gt EF M to show the selected chase Selects the cross fade speed between the steps of the selected Ce chase effect Selects the speed of the selected Ce chase effect Co E Sets the red intensity Select ModE gt MANU manual to show the result La Se nn mu sl ia Ai 2c mon eS ES a cJ J3 3 ce Gc C3 0 mq E n AA Sets the green intensity Select ModE gt MANU manual to show the result oi a Pu t Sets the blue intensity Select ModE gt MANU manual to show the result Sets the amber intensity Select ModE gt MANU manual to show the result Co 53 m mo uy yy wy lo uy W Affects df amp amp bT modes only Determines how colours are assigned to DMX channels Options are HCh and JCh red amp amber combined z0 a Em Ez ihg or eal y na E iy Determines whether this fixture will act as a master controlling others When controlled by DMX input this fixture must be set to SLAY Ee a Lt A Affects dit amp 1BbT modes only When set o this enables the master intensity channel for dl amp 1BbT modes D ET When set al this option scrolls through the primary colours at power on to demonstrate correct operation Det
Download Pdf Manuals
Related Search