jarag - 5 - Swiss Light Consulting
Contents
1. Reduce the value Holding down the or key increases the rate of change When a value is being changed all 4 decimal points are lit on the display By default the display is either blank or shows the DMX address of the lighting system To enter the setup menu press lt ENTER gt The display automatically returns to its default state if no selection is made for 1 minute Setup menu structure DS 4 12 or Add Fm Set DMX address PEr S Set DMX mode I rot Rotation l tESt Lamp test CtrL a Manual control Soft jm Software version DISP jm Set display mode DfLt Default settings 10 diMM La DIMMER SPEd SPEED FAdE FADE SEG SEQUENCE Banh La BANK JARAG 5 User Manual Con _ Addr Function Sets DMX address Value The value is the first DMX channel for the lighting system Minimum 1 Maximum 512 nominal Maximum value for 6 channel personality 507 Maximum value for 25 channel personality 488 Maximum value for 31 channel personality 482 Pers Function Sets DMX personality Value 6 ch 6 DMX channels using internal sequences 25ch 25 DMX channels direct array addressing 31ch 31 DMX channels internal sequences array using HTP See chapter 5 for th2. DMX control 6 channel sequence channel 1 Intensity channel 2 Speed channel 3 Effects channel 4 Rotation H V reflection channel 5 Sequence channel 6 Sequence bank variable cross fade low voltage lamp emulation DMX control 25 channel matrix channel 1 to 25 Intensity lamp 1 to 25 25 independent circuits DMX control 31 channel dual HTP Highest Takes Precedence prioritisation of 6 channel sequence and 25 channel array modes channel 1 to 6 Sequence control channel 7 to 31 Array control Kit of 25 PAR20 25 lamps for JA121 Kit of 25 PAR30 10 lamps for JA221 Yoke mounting for JA121 and JA221 Transport flight case for 2 x JA121 Transport flight case for 2 x JA221 Sequence programming software Manual control Manual digital control on rear panel with four keys and display Settings DMX address DMX personality lamp test rotation of the lighting system activating a sequence resetting to factory settings PC control RS232 C The lighting system can be controlled by a PC to upload and save sequences as well as setting up the lighting system Control program Can be downloaded from www chromlech com Requires a PC Win2K XP with RS232 C port for connection to the JARAGs Can be used to create prepare and simulate patterns and sequences without being connected to the lighting system Can be used to upload sequences to and save sequences from
3. Omer LIE de okei DIAN EE sedimine JARAG 5 User Manual RevC JA121 JA221 FW V2 1 Chromlech 80 avenue des Buttes de Co smes Batiment Gallium 35700 RENNES FRANCE Tel 33 0 2 23 20 77 67 Fax 33 0 2 23 20 75 71 E mail contact chromlech com Web www chromlech com Ciromech _ Table of Contents Table OT COMES sv eee 1 TV The JARA Gassene riene dad 2 Lamp EEE EE Lad bina di a da 2 Interhnal sequencer usina india ide a dada a aan 2 6 DMX channel personality saciar nee 3 29 DMX channel personality vin a a aasia m 3 oe AAA a a 3 JAT2TAIMENSIONS iia erica 4 JA221 dimensions ee 4 ME NS 5 Direct fastening EEE ERE A DA 5 Using the S re No aars 5 A no qm DR ERR SANOA EAA SEa RdA RaDa NN 5 3 Precautions IM USO vr 6 4 Control panel A A A A OR 7 CONN CIONS marsjere 8 I 165 110 JE EE EE EE ER 9 Setup MENU O 10 Setup menu structure ii iiiiieeeeeeeeeeeeeereeereenneeneeneeeeeeenene 10 9 DMX EE RER NE SE EE EE EE ee eee PR E 12 6 channel personality sequences cisma ic 12 25 channel personality MENN sota 14 31 channel personality dual EE EE ees 14 5 Programming re 15 T SPECHICANONS V re bed 16 6 Part UNDE Gus 16 o AAPP A A 17 JARAG 5 User Manual 1 harani db rapid rd 1 The JARAG 5 The JARAG 5 provides the same light output as a conventional lighting system but can be used to create a wide range of lighting effects The dimmers sequencer and control interfaces are built in so that t
4. Speed step Cross fade low voltage lamp effect Rotation reflection Sequence Sequence bank Channel 7 to 31 Matrix control 25 channel mode Channel 7 Lamp 1 Channel 31 Lamp 25 14 00000 00000 00000 000009 90099 JARAG 5 User Manual harani db matias g rd 6 Programming The sequences are programmed using the Jarag Control Center This program can be downloaded from www chromlech com Further information can be found in the program documentation JARAG 5 User Manual 15 Cronkct rar mes 0 ape scan 7 Specifications Power supply Mains supply 230V 50Hz 8A 1875 W Built in dimmers Lamps 25 220V 75W lamps JA121 Hi Spot ES63 25 2800K 2500h GU10 aluminium reflector JA221 Hi Spot ES95 10 2900K 3000h E27 aluminium reflector Chassis Matte black epoxy finish JA121 HxWxD 58 x 58 x 24 cm JA221 HxWxD 58 x 58 x 27 cm Weight without lamps 9 4 kg Attachment Yoke mounting or M10 holes on chassis Stacking JARAG systems can be stacked while maintaining a constant spacing between the lamps Connectors Mains cable 16A plug DMX in XLR5 DMX out XLR5 RS232 C SubD9 8 Part numbers JA121 JA221 JA102 JA202 JA123 JA124 JA224 JA105 16 Sequencer Built in sequencer with up to 256 32 step sequences controlled by DMX 128 sequences 8 banks of 16 are factory defined the remaining 128 can be user programmed
5. d 2 JARAG 5 User Manual ence db atin g tebe 6 DMX channel personality In 6 channel mode the 25 lamp sequence is controlled by the built in sequencer controlled by DMX using 6 channels to control all 25 lamps The sequences are controlled by DMX selection of the sequence speed of sequencing overall brightness fade time between steps orientation and reflection of the patterns The sequencer can store 256 32 step sequences each step defining the state of all 25 lamps Any lighting pattern can be defined as well as transitions The first 128 sequences are defined internally and are the same for all JARAG 5s providing a firm basis for creating lighting effects with the same controls for any lighting system see description of sequences in the appendix All of the remaining 128 sequences can be defined by the user to meet his requirements Pre coding special sequences makes it possible to have optimal light sequences for each lighting system The sequences are programmed using special software supplied free of charge downloaded from www chromlech com that operates under PC Windows The sequences can be defined and then uploaded into the lighting systems A graphic interface allows for simulating the sequences that have been defined 25 DMX channel personality The 25 DMX channel personality is used to control the 25 lamp array directly each DMX channel corresponds to one lamp In this case the internal sequencer and the seq
6. e assignment of the channels Rot Function Sets rotation of the lighting system Value UP no rotation UC 90 rotation dN 180 rotation 34 270 rotation Test Function Lights all the lamps for testing Value Test selected all the lamps are lit at low power Ctrl Function Manual control of the lighting system using 5 channels Value Dimm Dimmer channel intensity for the sequence Sped Speed channel speed or step selection for the sequence Fade Fade channel cross fade and LV halogen emulation Seq Sequence channel selects the sequence Banh Bank channel selects the sequence bank Disp Function Sets the default display mode Value On the display shows the DMS of the lighting system continuously Off the display shows the DMX address and goes off after about 1 minute Dfit Function Restores the default settings Value This sets the following values DMX address 1 personality 6 channels rotation 0 display On JARAG 5 User Manual 11 Ciromech _ 5 DMX control Three different DMX personalities are available 6 channel personality sequences 6 channel personality is used to replay sequences programmed in the built in sequencer Channel 1 Intensity 0 Off to 100 Full On Flash Full On starting from the first step of the sequence Channel 2 Speed Step 0 Off 3 Fast to 50 Slow 50 Step 1 to 95 St
7. ep 32 100 Synchronise sequence to first step Flash Channel 3 Cross fade Low voltage lamp effect 0 Fast to Off 50 Slow 50 Slow to On 100 Fast 12 JARAG 5 User Manual ont _ Channel 4 reflection Rotation O 12 None 0 13 25 Vertical 0 26 37 Horizontal 0 38 50 Vertical horizontal 0 51 62 None 90 63 75 Vertical 90 76 87 Horizontal 90 88 100 Vertical horizontal 90 Channel 5 Sequence selection 0 Sequence 1 to 100 Sequence 16 Channel 6 Sequence bank selection 0 Bank 1 to 100 Bank 16 JARAG 5 User Manual Ciromech _ 25 channel personality matrix The intensity of each lamp is directly controlled by a DMX channel as for a conventional dimmer and the built in sequencer is disabled The following schematic shows the channel assignments for the lamps Channel 1 to 25 Intensity 0 Off to 100 Full On 31 channel personality dual Each lamp is controlled simultaneously by the built in sequencer 6 channel mode and individually as an array 25 channel mode The lighting system calculates the intensity from the two modes using HTP Highest takes Precedence for each lamp individually Channel 1 to 6 Sequence control 6 channel mode Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Intensity
8. he system can be installed simply and easily It only requires a mains supply and an external DMX controller Lamp array The JARAG 5 has a 25 lamp array The type of lamp used depends on the lighting system model The JA121 takes PAR20 lamps GU10 and the JA221 takes PAR30 lamps E27 The lamps are controlled individually by a built in 25 channel dimmer Internal sequencer The lighting system has an internal sequencer which makes it easier to control the lamp array The sequencer can store up to 256 sequences A sequence is a series of steps maximum 32 played in a loop and the brightness speed and effects can be adjusted in real time Each step defines the state of each of the 25 lamps The sequences are stored in 16 banks of 16 sequences The sequences for banks 1 to 8 are factory set and cannot be changed These sequences are common to all JARAG 5s and provide a firm basis for creating lighting effects with the same controls for any lighting system see description of sequences in the appendix The sequences for banks 9 to 16 can be defined by the user These sequences allow each lighting system to be set up to meet the user s requirements The sequences are programmed using special software supplied free of charge downloaded from www chromlech com that operates under PC Windows The sequences can be defined and then uploaded into the lighting systems A graphic interface allows for simulating the sequences that have been define
9. iromech _ Connectors DMX IN Function DMX 512 input Type XLR 5 pin male Pinout 1 Shield ground 2 DMX primary data 3 DMX primary data 4 Not connected 5 Not connected DMX OUT Function DMX 512 output Type XLR 5 pin female Pinout 1 Shield ground 2 DMX primary data 3 DMX primary data 4 Not connected 5 Not connected RS232 Function SubD 9 pin female Type Serial link to PC Pinout Not connected TX output RX input DTR input Ground Not connected Not connected Not connected Not connected J O O1 B N JARAG 5 User Manual Ciromech _ Indicators POWER Off No power or fuse F1 blown Green Power on STATUS Off Normal operation Red Malfunction Maintenance required DMX Off No DMX signal Green DMX signal OK Green flashing orange Occasional DMX errors poor quality DMX signal Check the connections and signal integrity Red DMX connection fault or polarity inversion DMX signal not usable JARAG 5 User Manual Ciromech _ Setup menu The setup menu uses the following keys Navigation through the menu Setting a value ENTER Select sub menu Save the value EXIT Exit sub menu Cancel changes Next item Increase the value Previous item
10. ower control unit and is designed to be connected directly to the mains It must not be powered through a dimmer The lamps used in the lighting system have an aluminium reflector which reflects the heat to the front Every care should be taken to install the lights clear of nearby objects The lighting system should be disconnected from the mains before any maintenance operation The rear panel must not be opened when the lighting system is powered up Before use check that the lighting system cable and plug are in good conditions and that the power supply used is correctly earthed The lighting system should not be exposed to rain or water The lighting system must always be secured with an appropriate safety cable 6 JARAG 5 User Manual Cronkct rar races 0 age scan 4 Control panel The main operating parameters can be set using the built in control panel This panel has four keys and a display and is located on the back of the lighting system The settings are stored in non volatile memory RAS hromlech WARNING lamps are hot For professional use only Disconnect power before servicing the equipment 230 V 25x MAX 75W 1875 W 8 2 A Min distance to lighted object 1 m Min distance to flammable objects 1m Max ambient temperature 40 C Max exterior surface temperature 60 C Made in France STATUS O POWER O 00000 Te DMX IN DMX OUT RS232 Control panel rear JARAG 5 User Manual 7 C
11. the lighting system as well as testing and setting up the lighting system using a built in control console Jarag 5 for aluminium reflector PAR20 GU10 lamps Jarag 5 for aluminium reflector PAR30 E27 lamps JARAG 5 User Manual liege cb rat e oe JARAG 5 User Manual Sequence table Crone _ page left intentionally blank 18 JARAG 5 User Manual
12. uences it contains are not used 31 DMX channel personality The 31 DMX channel personality makes it possible to use the 6 channel sequencer mode at the same time as the 25 channel matrix mode The lighting system uses a Highest Takes Precedence HTP priority system for each lamp This allows a matrix controller to be used for example for overall animation of a JARAG light wall while still being able to use the internal sequences that can be superimposed as required JARAG 5 User Manual 3 Con JA121 dimensions 576mm 63 mm diam JA121 front view JA221 dimensions 576mm JA221 front view 200 mm 200 mm JA121 side view 200 mm 200 mm JA221 side view JARAG 5 User Manual Lacio de 2 Installation The JARAG 5 can be installed in any orientation Direct fastening There are 24 M10 holes on the edges of the JARAG 5 chassis 12 at the front and 12 at the back so that the lighting system can be suspended using hooks slings or shackles Using the yoke mounting The yoke mounting is attached to 4 holes on the side of the JARAG 5 to adjust the inclination and orientation of the lighting system easily Stacking arrays The JARAG 5 lighting systems can be stacked to form larger arrays using M10 bolts in the side holes JARAG 5 User Manual 5 harani db rapid rd 3 Precautions in use The JARAG 5 lighting system has its own p
Download Pdf Manuals
Related Search