Mania SCX800
Contents
1. The rotating gobos fitted to the Mania SCX800 are standard interchangeable items A range of replacement gobos is available from your Martin 6 dealer To replace a gobo 1 Disconnect the fixture from power and allow to cool for at least 20 minutes 2 Loosen the lamp cover release screw and open the cover on its hinge 3 See illustration on right Pull the gobo gently away from the gobo wheel and slide it up and out of the wheel 4 Slide the new gobo in and push gently towards the wheel to clip it into place Check that the gobo is held securely 5 Replace the lamp cover securely before reapplying power Service and maintenance 27 Gobo orientation Focus is easiest to maintain if all coated gobos in a fixture are installed with their coatings as close as possible to the same plane of focus However if there is a risk of heat damage the first priority is normally to ensure that more reflective sides face towards the lamp If in doubt install custom coated gobos with the more reflective side towards the lamp or consult your Martin dealer or gobo supplier More reflective side towards Less reflective side away from lamp lamp ND Y Sy em To minimize the risk of gobo The less reflective side of a coated overheating and damage installa gobo will absorb less heat if it coated gobo with the more faces away from the lamp reflective side facing towards the lamp To determine which side of a gobo i2. nh 20 Movement 20 Dimiming zs erciy ERI de DE 20 Information readouts l l 20 Manual control es 21 Effects test a esp A v e ie 22 Upload mode 3 5 tsa wes dada 22 Service and maintenance elle eens 23 Lamp replacement 23 leaning 2 or nets epe ROTER WE AS RE EL P Eres 25 Replacing the main fuse e e eee 26 Rotating gobos 27 Errormessages e e Rte 29 Software uploads res 29 Troubleshooting oc nce ule xg REG EE EE EE 30 DMX protocol ue a e EE n eee 31 Control menus 35 Circuit board layouts 38 Specifications tii bes 39 Notes 1 INTRODUCTION Important Thank you for selecting a Martin Mania SCX800 This automated rotating mirror projector has the following features 8interchangeable rotating gobos including 3 glass gobos and 5 aluminum glass gobos 172 pan swivel and 360 tilt continuous rotation Manually adjustable focus DMX control with two DMX modes DMX mode 2 gives extended functionality on additional channels Auto triggering and music triggering modes Stand alone single fixture and synchronized master slave modes Professionally designed pre programmed effects macros Rotating gobo indexing Long life 150 Watt discharge lamp Unpacking The packing material is carefully designed to protect the fixture during shipment always use it to transport the fixture The Mania SCX800 is supplied with 150 W discharge lamp
3. 2 Loosen the lamp cover release thumbscrew and open the lamp cover on its hinge Service and maintenance 25 26 3 Remove the two Philips head Remove dust and dirt from the Replace the fan making sure no Replace the lamp cover before screws on the fan housing and lift out the fan for access see illustration fan blades and vent grill using a soft brush or cotton swab and vacuum wires are trapped reapplying power Replacing the main fuse The Mania SCX800 uses a time delay fuse for protection against current overload An indication that the fuse may have blown is that when power is applied and the lamp is switched on no light is produced If the fuse blows repeatedly there is a fault with the unit that requires service by a Martin technician Never bypass the fuse or replace it with one of another type or rating 1 Disconnect the fixture from power and allow to cool for at least 20 minutes Pry open the fuse holder located next to the power cable entry with a flat head screwdriver and remove the fuse Replace the fuse with one of the same type Fuse ratings are listed on serial number labels and under Electrical on page 40 Replace the fuse holder If fuses continue to blow there is probably a fault Disconnect the fixture from power and data and contact a Martin service technician Mania SCX800 user manual qu V gt o Fuse holder Rotating gobos
4. set to music triggered operation Rotating gobos Speed and direction of gobo rotation can be controlled Gobos can also be set to shake or set to music triggered operation Gobo angle can also be indexed i e set to a precise angle Pan mirror drum swivel with approx 172 available Tilt mirror drum rotation with 360 continuous rotation available In DMX mode 2 the following additional functions can be controlled on four extra channels Macros A range of factory set macros are available with macros that control pan tilt and macros for the other effects on two separate channels The macros are professionally designed programs that use all the fixture s effects to give complete light shows with minimal user programming required Pan tilt speed and effects speed The speed at which the fixtures s mirror pans and tilts and the speed at which effects change can be adjusted on two extra channels Selecting a speed allows you to adjust fade times when using DMX controllers that do not feature fade time programming a fade time is the time taken for effects to change from one scene to the next If you select tracking on these channels the DMX controller defines fade times Operation 17 Unsure about speed and tracking As a rule you should set the fixture to tracking if you are using programmed fade times or macros on your DMX controller Select an effects speed if you are not using programmed fade times or macros on your
5. supplied separately to avoid damage during shipping and must be installed before use see Installing the lamp on page 24 Power cable RS 485 XLR cable for data link User manual Mounting U bracket with fasteners Allen key The mirror drum is secured for transport Before applying power remove all transport packaging remove the protective film from the mirror and cut and remove all plastic tie wraps holding the drum Introduction 5 Mania SCX800 overview Control panel and display Swivel lock Power on off switch DMX 1n DMX out Power cable connector and fuseholder T Power voltage selector switch Connections panel Mania SCX800 user manual Warning Safety information This product is for professional use only It is not for household use This product presents risks of lethal or severe injury due to fire and heat electric shock ultraviolet radiation lamp explosion and falls Read this manual before installing or powering the fixture follow the safety precautions listed below and observe all warnings in this manual and on the fixture If you have any questions about how to operate the fixture safely please contact your Martin dealer or call the Martin 24 hour service hotline Protecting yourself and others from electric shock and injury Disconnect the fixture from AC power before removing or installing the lamp fuse or any part and when
6. DMX controller However if you are using fade times on your controller and have set the fixture to tracking but effects movement is rough and irregular setting fade times on your controller to zero and selecting an effects speed may give smoother movement Effects movement is set to tracking if the fixture is in DMX mode 1 and by default DMX signal indicator When the Mania SCX800 receives a valid DMX signal the Data LED will light to show that the fixture is receiving control data Focus adjustment Never look directly into the light beam while adjusting the focus The focus adjustment knob is next to the lens aperture see illustration below Focus adjustment knob Adjusting music level sensitivity you can adjust response to a music beat while a fixture is in music trig mode by adjusting music level sensitivity Mania SCX800 user manual With the fixture powered on and in music trig mode play a typical music track at typical volume for your location Press the Menu button once and use the Up and Down buttons to scroll to U T IL Press Enter and scroll to ML EI music level menu Press Enter The fixture is supplied set to level 7 You can adjust the music sensitivity level using the Up and Down buttons to select a level from LE 1 to LE 15 Level 1 gives highest sensitivity Press Enter to activate the selected level Repeat step 3 until you find a level that gives the best response t
7. M12 bolt and lock nut through the 18 mm hole in the center of the mounting bracket or as recommended by the clamp manufacturer 3 If fastening the fixture directly to a mounting surface ensure that any fasteners used and the mounting surface can bear at least 10 times the fixture s weight The fixture may be fastened using any of the following four of the 6 5mm holes in the sides of the U bracket two 8mm holes in the top of the U bracket Mania SCX800 user manual Important one 13mm hole in the top of the U bracket 4 Ensure that the structure used to support the fixture can support at least 10 times the total weight of all installed fixtures clamps cables auxiliary equipment etc 5 Install a safety wire that can hold at least 10 times the weight of the fixture through over the support and through a safety wire attachment point next to one of the swivel locks on the fixture see illustration Do not simply attach the safety wire to the mounting bracket as this will leave the fixture unsecured Safety wire attachment point 6 Loosen the swivel locks and tilt the fixture to the desired angle Turn the swivel locks clockwise to tighten Check that both swivel locks are tight and that the fixture is securely clamped in position Creating a data link for DMX or synchronized operation You need a serial data link to run light shows on one or more fixtures using a DMX controller or run synchronized
8. not in use Always ground earth the fixture electrically Do not use the fixture with a damaged power cable or cord cap mains plug Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection Do not expose the fixture to rain or moisture Refer all service not described in this manual to a Martin service technician Glass lenses must be replaced if they have become visibly damaged to such an extent that their effectiveness is impaired for example by cracks or deep scratches Do not operate the fixture if covers are open or if any component is missing damaged or deformed an unshielded discharge lamp emits dangerous UV radiation that can cause burns and eye damage A hot discharge lamp is under pressure and can explode without warning Allow the luminaire to cool for at least 20 minutes and protect yourself with safety glasses and safety gloves before replacing the lamp or servicing the luminaire internals f the quartz envelope of a discharge lamp is broken the lamp releases a small quantity of mercury and other toxic gases If a discharge lamp explodes in a confined area evacuate the area and ventilate it thoroughly Wear non porous safety gloves when handling a broken discharge lamp Treat broken or used discharge lamps and used safety gloves as hazardous waste and send to a specialist for disposal Do not stare directly into the light
9. operation and software version Power on hours This readout can be used to track maintenance intervals Mania SCX800 user manual There is a resettable counter in this menu Read the number of hours the fixture has been powered on since the counter was reset in INFUSTIMESHRSSRSE T Press Enter to display Press Up for 5 seconds to reset the counter to zero INFUSTIMESHRSST TL displays the total number of hours the fixture has been powered on since manufacture Press Enter to display This counter is non resettable Lamp hours This readout can be used to monitor lamp life for replacement purposes There is a resettable lamp hours counter in this menu Read the number of hours the lamp has been powered on since the counter was reset in INFOUSTIMESL HRASRSET Press Enter to display Press Up for 5 seconds to reset the counter to zero each time you install a new lamp INFO gt STIMESL HR gt TOTL displays the total number of hours of lamp use since manufacture Press Enter to display This counter is non resettable Start up lamp strike counter INFUSTIMESLSTSRSET is a resettable start up counter The fixture displays the number of times the lamp has been struck since the counter was last reset Press Enter to display Press Up for 5 seconds to reset the counter to zero each time you install a new lamp INFO gt STIMESLST gt TODTL displays the total number of lamp strikes since manufacture Press Enter
10. output Never look at an exposed lamp while it is lit Introduction Replace the lamp if it becomes defective or worn out Protecting yourself and others from burns and fire Do not attempt to bypass thermostatic switches or fuses Replace defective fuses with ones of the specified type and rating Keep all combustible materials for example fabric wood paper at least 0 1 meters 4 inches away from the fixture Keep flammable materials well away from the fixture Do not illuminate surfaces within 1 meter 3 3 feet of the fixture Provide a minimum clearance of 0 1 meters 4 inches around fans and air vents Do not place filters or other materials over the lens or mirror Allow the fixture to cool for at least 20 minutes before opening the fixture or removing the lamp Do not modify the fixture or install other than genuine Martin parts Do not operate the fixture if the ambient temperature Ta exceeds 40 C 104 F Protecting yourself and others from injury due to falls When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Verify that all external covers and rigging hardware are securely fastened Use an approved means of secondary attachment such as a safety cable installed as described in this manual Block access below the work area and work from a stable platform whenever installing or removi
11. 120 V 60 ecu asrar ee ke Nae bok eR eet 225 W 2 0 A PF 0 970 V volts Hz hertz W watts A amps PF power factor Measurements made at nominal voltage Allow for a deviation of 10 Thermal COOLING Loza Sea wx dda eee eae ey cael wade ee Forced air Maximum ambient temperature Ta lt 06 6 eee eee 40 C 104 F Maximum surface Temperature 80 C 176 F Total heat dissipation calculated 110 V 10 60 Hz 670 BTU hr Total heat dissipation calculated 230 V 10 50 Hz 710 BTU hr Approvals ANTERTE C ly Listed EU Saleh a e E ret e epe eR Ere Ed EN 60598 1 EN 60598 2 17 EU EMC EN 55015 EN 55022 EN 55024 EN 61000 3 3 EN 61000 3 2 EN 61547 US Safety ria A eed A DE UL 1573 Canadian safety 0 2 0 cece cette ee CSA C22 2 NO 166 Mania SCX800 user manual Included items EU models Long life 150 W discharge lamp 3 meter 9 8 ft EU power cable 3 x 1 0 mm Schuko male connector P N 11501017 3 meter 9 8 ft EU power cable 3 x 1 0 mm no male connector P N 11501013 5 meter 16 4 ft RS 485 XLR cable for data link a nananaaaana P N 11820008 L type 5mm Allen key P N 50520615 User manual 32 va ee eme ehe ral ee rea qnd P N 35000213 Adjustable U bracket 2 AT 5x20 mm main fuse installed lessen P N 05020009 Included items US models Long life 150 W discharge lamp 2 meter 6 5 ft US AC power cable 18AWG with U
12. B3 by an equal amount in the direction that gives an improvement until a satisfactory beam is obtained Mania SCX800 user manual Cleaning Cleaning optical components Use care when cleaning optical components The coated surfaces are fragile and even small scratches may be visible in the fixture s light output Wear cotton gloves to avoid contaminating components with grease from your fingers 1 Disconnect the fixture from power and allow it to cool for at least 20 minutes 2 Loosen the lamp cover release thumbscrew and open the lamp cover on its hinge 3 Blow or vacuum away loose dust Remove residues from lenses and filters with a soft cloth or cotton swabs wetted with isopropyl alcohol Regular glass cleaner may also be used but no residues may remain 4 Rinse with distilled water Mixing the water with a small amount of wetting agent such as Kodak Photoflo will help prevent streaking and spotting 5 Dry with a clean soft and lint free cloth or blow dry with compressed air 6 Replace the lamp cover before reapplying power Cleaning the fan and air vents To maintain adequate cooling dust must be cleaned from the fan and air vents periodically Cleaning intervals will depend on the operating environment The presence of airborne dust smoke etc will make frequent cleaning necessary Check and if necessary clean fixtures regularly 1 Disconnect the fixture from power and allow to cool for at least 20 minutes
13. Fuse 5A 250V J1 J8 Fan F Filter PCBA 7 T Bos SCX800 op ar IE Power PCB J9 Main PCBA EU J13 Ignitor N s Capacitor Main PCBA Display PCBA Hall Sensor Gobo SCX800 Main PCB Hall Sensor 3 Rotation Gobo 2 J3 Power PCBA Power PCBA J6 J9 J6 Pan Tilt Shutter Gobo Rotation Gobo 38 Mania SCX800 user manual SPECIFICATIONS Physical Size svwWxvHt eee 550 x 240 x 202 mm 21 7 x 9 4 x 8 0 in Height including bracket eese 432 mm 17 0 in Weight EU model including brace nanunuraaa unnn 13 5 kg 29 8 Ibs Weight US model including brackett eee 14 7 kg 32 4 Ibs Lamp Type oes koe race et s eR e AAA 150 W discharge Approved lamps Philips MasterColor CDM SA T 150 Osram HSD 150 70 SOCKOl dS errori dti EES G12 Dynamic effects Rotating gobo wheel 8 interchangeable gobos with gobo indexing rotation shake music mid ooo Mechanical dimmer shutter O 100 continuous dimming instant open amp blackout strobe effects music triggered shutter Motorized mirror drum 172 pan swivel and 360 tilt continuous rotation Control and programming Control options s es n anaana DMX stand alone synchronized master slave DMX channels 5 mode 1 or 9 mode 2 DMX address setting Onboard contr
14. LK CPU software version number Table 2 Control menu Control menus 35 RST Reset fixture L ON Lamp on Loft Lamp off DPEN Open shutter CL US Close shutter SHUT STRF Shutter strobe fast STRM Shutter strobe medium STRS Shutter strobe slow dIM 8 255 Dimmer 61 1568 I Indexed gobo selection 1 gt 8 MAN 90b0 61R566 R Rotating gobo selection 1 gt 8 5 HDD Rotating amp shaking gobo selection 1 gt 8 1 5 8 255 Gobo rotation speed slow gt fast B 127 Pan position left gt right NS 5 Narrow shake slow NS M Narrow shake medium PAN NS F Narrow shake fast WS 5 Wide shake slow HG M Wide shake medium WS F Wide shake fast 36 Table 2 Control menu Mania SCX800 user manual CWS Clockwise rotation slow CU H Clockwise rotation medium CU F Clockwise rotation fast COWS Counterclockwise rotation slow COW H Counterclockwise rotation medium MAN COW F Counterclockwise rotation fast on TILT NS 5 Narrow shake slow NSM Narrow shake medium NS F Narrow shake fast WS 5 Wide shake slow WS H Wide shake medium WS F Wide shake fast TSEQ RUN Run a general test of all effects UTIL Manually set fixture to software updat Press UPL SURE mode y paate Enter a to MLEV LE 15 Music sensitivity level 1 most sensitive access LE 16 7 default Table 2 Control menu Control menus 37 9 CIRCUIT BOARD LAYOUTS Transformer
15. Mania SCX800 user manual DIMENSIONS All dimensions are in millimeters 240 2007 Martin Professional A S All rights reserved No part of this manual may be reproduced in any form or by any means without permission in writing from Martin Professional A S Information subject to change without notice Martin Professional A S and all affiliated companies disclaim liability for any injury damage direct or indirect loss consequential or economic loss or any other loss occasioned by the use of inability to use or reliance on the information contained in this manual P N 35000213 Rev A Contents Introd ction roman a eaa A ee SE 5 Unpacking 22 KR E E Rg be x ee EE ages 5 Mania SCX800 overview 6 Safety information spa dara ara EN 7 Installation i364 A Sa de eet EE 9 AG DOWOF tne Renee bdo s DI Y ab ei ebd 9 Rigging the fixture aar a 9 K R RR Ra ZR RN N a R RN EA A OEE EAA 10 Creating a data link for DMX or synchronized operation 11 Operation daier Eege dit Egeter ege bi e 12 Gettilig started cere ECRIRE MERE EA Aa 13 Music trig auto trig and DMX modes anaana aaa 14 Synchronized music trig and auto trig operation 15 DMX controller operation x e oo 16 FOCUS adJUSTMENE cere Rea etes et Vx aber 18 Adjusting music level sensitivity llle 18 Control panel
16. S male connector UL approved P N 11501501 5 meter 16 4 ft RS 485 XLR cable for data link nananana P N 11820008 L type 5mm Allen key P N 50520615 Usermantal Go x rore Sr sete ces etes an Disaster e LIEU ata EES E P N 35000213 Adjustable U bracket 3 15 AT 5x20 mm main fuse installed o o o P N 05020043 Accessories Philips MasterColor CDM SA T 150 W discharge lamp P N 97010111 Osram HSD 150 70 150 W discharge lamp 000 P N 97010117 DMX termination plug end of link XLR male P N 91613017 DMX termination plug start of link master slave XLR female P N 91613018 GE elamp 4s scs bans mta cer se eras rado reddas Bilin E P N 91602003 H lf Goupler clamp ene vo tC ET AY XE P N 91602005 5 pin male to 3 pin female XLR adaptor cable P N 11820005 5 meter 16 4 ft RS 485 XLR cable for data link P N 11820008 Mania SCX800 EU models main fuse 2 AT eee P N 05020009 Mania SCX800 US models main fuse 3 15 AT P N 05020043 Ordering information Mania SCX800 EU model 220 240 V 50 HZ P N 90430088 Mania SCX800 US model 110 120 V 60 HZ P N 90430089 Specifications 41 42 Disposing of this product Martin products are supplied in compliance with Directive 2002 96 EC of the European Parliament and of the Council of the European Union on WEEE Waste Electrical and Electronic Equip
17. aged cables Data link not terminated with 120 Ohm termination plug Insert termination plug in output of last fixture on link Incorrect fixture addressing Check DMX addresses One of the fixtures is transmitting as a master Check all fixture settings One of the fixtures is defective Bypass one fixture at a time unplug both DMX connectors and connect them directly together until normal operation is regained Have defective fixture serviced by a Martin technician A number appears in display and fixture will not run a stand alone light show Fixture is set to DMX mode and is displaying its DMX address Use control panel to change fixture from DMX to stand alone auto trig or music trig An effect fails to reset correctly The effect may require mechanical adjustment Contact Martin technician for service Lamp cuts out intermittently or burns out too quickly Fixture is too hot Allow fixture to cool Check that there is free airflow around the fixture Check and if necessary clean fan and grills Fixture does not respond correctly to music beat in music trig mode Music level sensitivity is incorrectly adjusted Use control panel to adjust sensitivity until fixture responds satisfactorily Impossible to restrike lamp after dousing via DMX 8 minute restrike protection delay activated Mania SCX800 user manual Wait 8 minutes befo
18. ale Male XLR Female XLR 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 3 3 3 3 ee 3 120 Ohm 32120 Ohm 4 4 5 5 P N 11820005 P N 11820004 P N 11820006 P N 91613017 P N 91613018 DMX connectors and polarity To connect the data link 1 Power all devices off 2 If you intend to use a DMX controller run a data cable from the DMX controller s data output to the first fixture s data IN socket If the controller has a 5 pin output use a 5 pin male to 3 pin female adaptor cable available from your Martin dealer P N 11820005 3 If you intend to run fixtures in master slave operation insert a female DMX termination plug P N 91613018 in the first fixture s data IN socket Plug a data cable into the OUT socket of the first fixture and the IN socket of the next one Continue connecting up to 32 fixtures output to input Terminate the link by inserting a male termination plug P N 91613017 into the data output of the last fixture A termination plug is simply an XLR connector with a 120 Ohm 0 25 W resistor soldered across pins 2 and 3 Mania SCX800 user manual 3 OPERATION Note The Mania SCX800 is supplied in DMX mode with its DMX address set to 1 If want to operate the fixture without a DMX controller you need to set the fixture to stand alone music trig or auto trig mode before use see Selecting DMX music trig or auto trig operating modes on page 14 Getting started Powering on Once the Mania SCX800 is
19. arning 10 brown wire to live and the blue wire to neutral The table below shows some pin identification schemes Wire Pin Marking Screw color brown live SL yellow or brass blue neutral N silver yellow green ground SE green Table 1 Power plug cord cap wiring Rigging the fixture The Mania SCX800 must be mounted by means of its adjustable U bracket Do not install the fixture by any other means as this can cause the fixture to overheat The U bracket can be either fastened to a flat surface or attached to a rigging clamp Suitable rigging clamps are available from your Martin dealer Block access below the work area and work from a stable platform when installing or servicing the fixture Do not operate the fixture without fastening it securely to a structure or surface Use a secure means of secondary attachment that can hold at least 10 times the weight of the fixture 1 The fixture must be located at least 1 meter 3 3 ft away from the surface to be illuminated and at least 0 1 meters 4 in from any combustible materials wood fabric paper etc Ensure that the clearance around the fan and air vents is at least 0 1 meters 4 in Ensure that there are no inflammable materials nearby 2 If using a rigging clamp ensure that the clamp is undamaged and can bear at least 10 times the fixture s weight Bolt the clamp securely to the fixture s mounting bracket with a grade 8 8 minimum
20. correctly and safely installed power on at the fixture s power on off switch The fixture will start up and reset The display will show the following messages 1 DK 2 Fixture name 3 Software version number 4 RST If the fixture resets successfully it will display either its DMX address SA M stand alone music trig mode or 5H H stand alone auto trig mode If any other message is displayed the fixture has detected an error see Error messages on page 29 If this occurs switch off wait a few seconds and switch on again If the error message appears again consult your Martin dealer Control panel and menus You can set the Mania SCX800 s DMX address modify the fixture s personality and control effects manually using the menus in the control Operation 13 14 panel See also the overviews printed on the fixture and in Control menus on page 35 Power indicator LED Na HN DU EN KN N IAN TW Data indicator LED O O O O Menu Enter Up Down Control buttons To enter the menus press the Menu button Use the Up and Down buttons to scroll within a menu To select a function or submenu press the Enter button To exit a function or menu press the Menu button Music trig auto trig and DMX modes The Mania SCX800 has three main operating modes Stand alone music trig mode In this mode lighting effects are triggered by music intensity Multiple fixtures can be synch
21. eck and if necessary clean fixtures at regular intervals Lamp replacement The Mania SCX800 uses a 150 W discharge lamp Replace the lamp when it reaches the average life specified by the manufacturer Use only this type of lamp See Accessories on page 41 for details of replacement lamps Installing any other lamp may damage the fixture Service and maintenance 23 Installing the lamp 1 Beam adjustment 1 2 Remove the lampholder by If replacing an old lamp Hold the new lamp by its base If you touched the bulb or any Reapply power and reset the Disconnect the fixture from power and allow it to cool for at least 20 minutes removing screws A see illustrations remove it from its ceramic socket do not touch any other part of the lamp Push the lamp pins squarely into the socket in the lampholder see illustration optical components clean them with a clean lint free cloth wetted with isopropyl alcohol Reinstall the lampholder in the fixture checking that no wires are trapped before screwing on the cover lamp hours counter see Information readouts on page 20 If the brightest part of the beam is off center use screw B1 to adjust horizontal lamp alignment use screw B2 and or B3 to adjust vertical lamp alignment If there is an excessive hot spot or dark area in the center of the beam or if light output is low turn all three screws B1 B2 and
22. from the Support area of the Martin website at http Awww martin com To prepare the Mania SCX800 to receive new software select UT IL gt UPL in the control panel then follow the instructions in the uploader user manual or help files If the fixture will not accept a software upload as described above it can be forced to accept an upload by setting it to hard boot mode To do this hold both the Menu and the Enter button pressed in while powering on the fixture The data LED will blink when the Mania SCX800 is in hard boot mode If you have difficulty carrying out uploads your Martin dealer will be able to give advice or carry out the upload for you Service and maintenance 29 6 TROUBLESHOOTING 30 Problem Probable cause s Remedy One or more fixtures is completely dead No power to fixture Check that power is switched on and cables are plugged in Main fuse blown Replace fuse Fixtures reset correctly but all respond erratically or not at all to controller Controller not connected Connect controller XLR pin out of controller does not match pin out of first fixture on link i e polarity is reversed Install a phase reversing cable between controller and first fixture on link Fixtures reset correctly but some respond erratically or not at all to controller Bad data link connection Inspect connections and cables Correct poor connections Repair or replace dam
23. ial burst 120 127 47 49 Gobo 8 Molecule Gobo shake 128 141 50 55 Gobo 1 shake fast slow 142 155 56 61 Gobo 2 shake fast gt slow 156 169 62 66 Gobo 3 shake fast gt slow 170 183 67 71 Gobo 4 shake fast gt slow 184 197 72 77 Gobo 5 shake fast gt slow 198 211 78 82 Gobo 6 shake fast gt slow 212 225 83 88 Gobo 7 shake fast gt slow 226 239 89 93 Gobo 8 shake fast gt slow Music triggered gobo chase 240 245 94 96 Fast 246 250 97 98 Medium 251 255 99 100 Slow Gobo indexing angle gobo rotation movement 3 music trig gobo rotation Gobo indexing angle select gobo on channel 2 0 255 0 100 Indexing 0 395 Gobo rotation set movement select gobo on channel 2 0 7 0 2 Stop 8 77 3 29 Rotation CW slow gt fast 78 147 30 57 Rotation CCW fast gt slow 148 153 58 59 Stop 154 223 60 87 Rotation CW slow fast 224 239 88 93 Rotation shake Music triggered rotation 240 245 94 96 Fast 246 250 97 98 Medium 251 255 99 100 Slow 32 Mania SCX800 user manual Channel Value Percent Function 4 Pan mirror drum swivel position shake and music trig 0 0 Maximum left pan 63 24 Neutral 127 50 Maximum right pan 128 182 51 71 Narrow shake slow fast 183 239 72 93 Wide shake slow fast 240 244 94 95 Music trig pan fast 245 249 96 97 Music trig pan slow 250 255 98 100 Music trig pan dynamic 5 Tilt mirror drum rotation rotation shake and music trig 0 1 0 No rotat
24. ion 2 63 1 24 Clockwise rotation slow fast 64 65 25 No rotation 66 127 26 49 Counterclockwise rotation fast slow 128 129 50 No rotation 130 184 51 72 Narrow shake slow fast 185 239 73 93 Wide shake slow fast 240 244 94 95 Mirror drum rotation music trig fast 245 249 96 97 Mirror drum rotation music trig slow 250 255 98 100 Mirror drum rotation music trig dynamic 6 Pan amp tilt macros DMX mode 2 only 0 15 0 5 No Macro 16 31 6 11 Macro 1 32 47 12 18 Macro 2 48 63 19 24 Macro 3 64 79 25 30 Macro 4 80 95 31 37 Macro 5 96 111 38 43 Macro 6 112 127 44 49 Macro 7 128 143 50 55 Macro 8 144 159 56 62 Macro 9 160 175 63 68 Macro 10 176 191 69 74 Macro 11 192 207 75 81 Macro 12 208 255 82 100 Reserved No function 7T Effects macros DMX mode 2 only 0 15 0 5 No Macro 16 31 6 11 Macro 1 32 47 12 18 Macro 2 48 63 19 24 Macro 3 64 79 25 30 Macro 4 80 95 31 37 Macro 5 96 111 38 43 Macro 6 112 127 44 49 Macro 7 128 143 50 55 Macro 8 144 159 56 62 Macro 9 160 175 63 68 Macro 10 176 191 69 74 Macro 11 192 207 75 81 Macro 12 208 255 82 100 Reserved No function DMX protocol 33 34 Channel Value Percent Function 8 Pan amp tilt speed Mode 2 only 0 7 0 2 Tracking default 8 240 3 94 Fast slow 241 245 95 96 Blackout during gobo changes 246 250 97 98 Blackout during pan and tilt changes 251 255 99 100 Blac
25. itable DMX addresses for all the fixtures on the data link 512 channels are available in one DMX universe Apply power to the fixture and wait while it resets Press Menu to enter the main menu Select Add using the Up and Down buttons Press Enter Select an address using the Up and Down buttons Press Enter Press Menu to return to the main menu o Om E wh Mania SCX800 user manual Fixtures remember their DMX address when they are powered off and on DMX control options See the DMX protocol on page 31 for an overview of DMX commands and channels In DMX modes 1 and 2 the following functions can be controlled Reset All effects can be reset to their index positions from the controller using channel 1 The reset command must be sent for 5 seconds before it takes effect When a fixture is reset via DMX RST appears in its display Dimming and blackout The Mania SCX800 can be blacked out using the shutter on channel 1 The shutter can also be set to music triggered operation The Mania SCX800 can be dimmed from 0 to 100 on channel 1 if PER gt INT is set to ON in the control menus Note that to douse the lamp a DMX value from 240 to 247 must be sent on channel 1 for at least five seconds If you douse the lamp you must wait eight minutes before restriking Gobo wheel position and rotation The gobo wheel features 8 rotating gobos Rotating gobos can be selected shaken at different speeds and
26. kout during gobo pan and tilt changes Effect speed Mode 2 only 9 0 7 0 2 Tracking default 8 255 3 100 Fast gt slow Channels 6 9 are available in DMX mode 2 only In DMX mode 1 pan amp tilt speed and effects speed are set to tracking Mania SCX800 user manual 8 CONTROL MENUS Factory default settings are shown in bold type Menu Item Options Notes default settings in bold print AddR 1 5 1g DMX address default address 1 PATI PINY Fan invert TINY Tilt invert PSET M d 1 DMX mode 1 normal MOde DMX mode 2 extended NORM DMX controlled operation slave 2 fixture e Stand alone auto trig operation auto trig MOdE SA A master fixture SA M Stand alone music trig operation music trig master fixture OFF Dimming disabled PER INT ee ON Dimming enabled T U TL total hours of operation since manufacture HRS RSE T resettable counter Press Enter to display hours of operation since counter reset To reset to zero press Up for 5 seconds T U TL total hours of lamp operation TIME L HR RSET resettable counter Press Enter to display hours of lamp operation since counter reset To reset to zero press Up for 5 seconds T U TL total number of lamp strikes RSET resettable counter Press Enter L ST to display number of lamp strikes since counter reset To reset to zero press Up for 5 seconds INFO VER KK
27. light shows on two or more fixtures master slave operation Fixtures on a serial data link must be daisy chained in one single line max 500 meters 1640 ft long with max 32 fixtures If you wish to exceed 32 fixtures or 500 meters or to add branches use an optically isolated amplifier splitter such as the Martin RS 485 Opto Splitter P N 90758060 Reliable data connection requires suitable cable Standard microphone cable cannot transmit DMX data reliably over long runs For best results use cable with at least one twisted pair specifically designed for RS 485 applications Your Martin dealer can supply suitable high quality cable in various lengths Installation 11 Connecting the serial data link The fixture s data connections are XLR type wired with pin 1 to ground pin 2 to signal cold and pin 3 to signal hot This is the standard configuration for DMX devices One or more adaptor cables may be required to connect the Mania SCX800 to the controller and or other types of fixture because some devices may have 5 pin XLR connectors and others may have reversed signal polarity pin 2 hot and pin 3 cold Connector polarity is normally specified on the device or in the device s user manual 5 pin to 3 pin 3 pin to 5 pin 3 pin to 3 pin Male DMX Female DMX Adaptor Adaptor Phase Reversing Termination Plug Termination Plug Adaptor Male Female Male Female Male Fem
28. ment as amended by Directive 2003 108 EC where applicable Help preserve the environment Ensure that this product is recycled at the end of its life Your supplier can give details of local arrangements for the disposal of Martin products Mania SCX800 user manual v Mart n www martin com e Olof Palmes All 18 8200 Aarhus N e Denmark Tel 445 8740 0000 e Fax 45 8740 0010
29. ng the fixture Mania SCX800 user manual 2 INSTALLATION Warning Important AC power The Mania SCX800 is supplied set up to match local voltage and frequency settings The factory setting is shown on the serial number label For protection from fire and electric shock the fixture must be grounded earthed The power supply must have overload and ground fault earth fault protection Check that power cables are undamaged and rated for the current requirements of all connected devices before use Ensure that the fixture s voltage setting matches your local AC power supply before applying power Do not connect the fixture to a dimmer system as this will cause damage that is not covered by the product warranty Power settings EU models can be set to 230 or 240 V 50 Hz AC power using the switch on the connections panel Use the 230 V setting if you have 220 230 V power and use the 240 V setting if you have 230 240 V US models do not have a switch and are supplied set up for 110 120 V 60 Hz AC power Installing a cord cap on the power cable The power cable must be fitted with a grounding type cord cap earthed mains plug that matches your AC power distribution system Consult a qualified electrician if you have any doubts about proper installation If you need to fit a cord cap follow the cord cap manufacturer s instructions connecting the yellow and green wire to ground earth the Installation 9 W
30. o the music beat Press Menu to save your setting and exit the music level menu The fixture will return to this setting when you power it off and on Operation 19 4 CONTROL PANEL 20 The following functions of the control panel are described earlier in this manual selecting stand alone music trig or auto trig operation see page 14 Switching between DMX modes 1 and 2 see page 16 setting DMX addresses see page 16 Setting music sensitivity level for music trig operation see page 18 This chapter describes the other control panel options for setting up fixture behavior see also Control menus on page 35 for a complete overview of control panel functions Movement PAT I the pan and tilt invert menu allows you to invert pan movement PIN and invert tilt movement T I NL These options can be useful in situations where you want some fixtures to mirror the performance of others with the same DMX address or when you install fixtures in a different orientation after you have programmed a light show Dimming The Personality gt Intensity setting PER INT lets you use the shutter for dimming When disabled the default setting the low values on channel 1 set the shutter to either fully open or fully closed When enabled the shutter can be opened and closed gradually giving 0 100 continuous dimming Information readouts INFO the information menu gives information about hours of fixture and lamp
31. ol panel with 4 digit display Stand alone options Music trig selectable via control panel or via DMX auto trig Protocol 2 d pue pare e eet NE ARE AS erdt USITT DMX512 1990 ROCOIVOR us sue pere eg d Tau n Cue aae e nA Dom ee d aes RS 485 Firmware update Serial upload via DMX link Optics Manual foGus tur Rene em me X re ee EAE 2m 6 6 ft 20m 65 6 ft Construction EQUINOS Md sendet veste SEIS d nete ss Steel and aluminum Gobos Outside diameter esee 22 5 mm 0 0 3 mm Maximum image diameter eh 17 mm Specifications 39 Installation Orientation i sss a ep Roe En e e Any Mounting points erm rm emer aa Adjustable bracket Minimum distance to illuminated surfaces llus 1 m 3 3 ft Minimum clearance around fan and air Vente ua ssaaa unana 0 1 m 4 in Connections AC power Input III 3 pin IEC male socket DMX data in OUl iso be Y as DIE Rh qe iR 3 pin locking XLR Electrical EU model eje 3 prong IEC male socket AC power ee switch selectable 230 V 240 V 50 Hz Main f se isses sso ted EY exa EUR UE opa oh do dU Rod Rs 2 AT Typical power and current 220V le EE 199 W 1 0 A PF 0 975 GEERT EE 215 W 1 0 A PF 0 968 240 V POH 231 W 1 0 A PF 0 968 US model al a fe EE 3 prong IEC male socket AG BEWEEGT Bee dave cheeks d e Rap enc eee 115 120 V 60 Hz Matus TTT 3 15 AT Typical power and current 110 V 60 Hz cene REPRE TEE E E EG 192 W 1 8 A PF 0 980
32. ow you to select pre programmed pan tilt and effects macros and set the speed of pan tilt and effects movement from the DMX controller To toggle between DMX modes 1 and 2 1 Apply power to the fixture and wait for the fixture to reset 2 In the control panel press the Menu button Then use the Up and Down buttons to scroll to PSE T personality setting and press Enter 3 Use the Up and Down buttons to scroll between MB d 1 and HD de and press Enter to save your setting The Mania SCX800 is supplied in DMX mode 2 Setting DMX addresses If you use a DMX controller you need to set the DMX address for each fixture on the fixture s control panel The DMX address or start channel is the first channel used to receive instructions from the controller For individual control each fixture must be assigned its own DMX address and control channels For example if a Mania SCX800 is set to DMX mode 2 and you give it DMX address 101 it will use channels 101 109 inclusive Channel 110 is available for the next fixture Fixtures with the same DMX address will receive the same instructions and behave identically Two fixtures with the same DMX address can be set up so that one pans as a mirror image of the other To achieve this use the settings in the control menu to invert the pan on one fixture see Movement on page 20 The default factory set DMX address is 1 To set a fixture s DMX address 1 Decide on su
33. re restriking a hot discharge lamp 7 DMX PROTOCOL Channel Value Percent Function Shutter dimmer strobe effect reset 1 With dimming disabled in PER INT default 0 18 0 7 Shutter closed 19 38 7 14 Shutter open With dimming enabled in PER INT 0 38 0 14 Continuous dimming 0 100 intensity 39 95 15 37 Strobe slow gt fast 96 103 38 40 Shutter open 104 151 41 59 Random strobe slow fast 152 159 60 62 Shutter open 160 199 63 78 Music triggered shutter 200 207 79 81 Shutter open 208 219 82 85 Lamp on 220 239 86 93 Shutter open 240 247 94 96 Lamp off must be held for 5 seconds 8 min delay before lamp can be restruck 248 251 97 98 Shutter open 252 255 99 100 Reset must be held for 5 seconds to blackout and reset DMX protocol 31 Channel Value Percent Function 2 Gobo selection gobo shake music trig gobo chase Gobo indexing select gobo set indexing angle on channel 3 0 7 0 2 Gobo 1 Spring wheel 8 15 3 5 Gobo 2 Blade 16 23 6 8 Gobo 3 Tricone 24 31 9 11 Gobo 4 Space badge 32 39 12 14 Gobo 5 Blender 40 47 15 18 Gobo 6 Red revolver 48 55 19 21 Gobo 7 Radial burst 56 63 22 24 Gobo 8 Molecule Gobo rotation select gobo set movement on channel 3 64 71 25 27 Gobo 1 Spring wheel 72 79 28 30 Gobo 2 Blade 80 87 31 33 Gobo 3 Tricone 88 95 34 37 Gobo 4 Space badge 96 103 38 40 Gobo 5 Blender 104 111 41 43 Gobo 6 Red revolver 112 119 44 46 Gobo 7 Rad
34. return to this mode when powered off and on Synchronized music trig and auto trig operation You can set multiple fixtures on a serial data link to respond together to a music trig or auto trig signal from one fixture This feature allows synchronized operation without a DMX controller The fixture sending the signal is the master fixture and the fixtures that receive the signal are the slave fixtures Set only 1 fixture on the link as master damage can occur if 2 masters or a master and a DMX controller are linked Setting up synchronized operation To set up Mania SCX800s for synchronized operation 1 Ensure that all slave fixtures are in DMX mode 2 Select one fixture to be the master and set it to stand alone auto trig or music trig mode see Selecting DMX music trig or auto trig operating modes on page 14 3 When slave fixtures receive signals from the master they will automatically begin operating in slave mode The Data LED on their control panels will light to show that they are receiving control data Fixtures return to their DMX auto trig music trig settings when powered off and on so you should only need to set fixtures as masters slaves once Operation 15 16 DMX controller operation Setting DMX mode 1 or 2 Two DMX modes are available DMX mode 1 normal and DMX mode 2 extended In mode 1 the Mania SCX800 uses 5 DMX channels In mode 2 it uses 9 channels The extra DMX channels in mode 2 all
35. ronized if one master fixture is set to stand alone music trig mode and the other fixtures are set to DMX mode Stand alone auto trig mode In this mode the fixture runs a factory set dynamic light show that uses all the fixture s effects in a random program Multiple fixtures can be synchronized if one master fixture is set to stand alone auto trig mode and the other fixtures are set to DMX mode DMX mode In DMX mode fixtures receive control instructions via the serial data link They will respond to control signals from a DMX controller or from another fixture set as master Selecting DMX music trig or auto trig operating modes The Mania SCX800 is supplied set to DMX mode with its DMX address set to 1 If you intend to operate the fixture without a DMX controller you need to set it to stand alone music trig or auto trig mode To switch between DMX auto trig and music trig modes 1 Apply power to the fixture and wait until the R 5 T message disappears from the display The fixture has now reset Mania SCX800 user manual Important 2 Press the Menu button once to enter the control menus 3 Use the Up and Down buttons to scroll to MO dE Press Enter once to enter the operating mode menu 4 Use the Up and Down buttons to scroll between e NORM DMX mode e 5A A Stand alone auto trig mode and e 5A M Stand alone music trig mode 5 Press Enter The fixture enters the mode you have selected and will
36. s coated hold an object up to it f On the uncoated side there is a space between the object and its pea reflection and the edge of the v gobo can be seen when looking through the glass Uncoated side Coated side To obtain the sharpest focus in the Mania SCX800 the gobos at positions 1 4 and 6 are oriented as follows The sandwich construction composite glass gobos at positions 1 and 4 are installed with the coated sides of the component gobo halves facing each other in the middle of the sandwich The glass gobo at position 6 is installed with the coated side towards the lens Mania SCX800 user manual Error messages In the event of an internal error the following messages will appear in the digital display e GODER Gobo wheel timeout RGER Rotating gobo timeout If one of the above error messages is displayed try powering the fixture off and then on again to reset it If the problem persists contact your Martin dealer The message HUT will be displayed if you douse the lamp via DMX and then try to restrike it within eight minutes Software uploads It is possible to upload new software to the Mania SCX800 via the DMX IN connector using for example an uploader such as the Martin MP 2 Uploader or a PC using a Martin DABS interface device and a suitable application such as the Martin Software Uploader The latest version of the Mania SCX800 software and the Martin Software Uploader are available
37. to display This counter is non resettable Software version INF GER displays the fixture software version number The software version is also displayed briefly when the fixture is powered on Manual control The manual control menu MAN provides commands for resetting the fixture R5 T as well as striking the lamp L DN and dousing the lamp Lof F It also permits you to position and move individual effects Control panel 21 22 Effects test The test sequence TSEG RUN runs through all effects to provide a quick check of fixture performance Upload mode The upload mode command UT IL 5 UPL prepares the fixture for a software upload see Software uploads on page 29 Mania SCX800 user manual 5 SERVICE AND MAINTENANCE Warning Important Important The Mania SCX800 requires simple routine maintenance The maintenance schedule depends heavily on the operating environment please consult a Martin service technician for recommendations Any service procedure not described here should be referred to a qualified technician Disconnect the fixture from power and allow it to cool for at least 20 minutes before removing any cover Wear safety glasses and gloves and allow the fixture to cool for at least 20 minutes before removing the lamp Excessive dust grease and smoke fluid buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty Ch
Download Pdf Manuals
Related Search