Declaration of Conformity Deklaracja Zgodności
Contents
1. 4 rollers 4 6 minutes 80 200mic 1mm 330 mm 360 420 mm min 50 60 Hz AC 220 240 V 50 60 Hz 460 W 2 0A 470x150x105 mm 3 4 kg2. Instrukcja obs ugi laminatora OPUS cityLAM A3 Declaration of Conformity Deklaracja Zgodnosci OPUS Sp z 0 0 hereby declares that the machine specified below is in accordance with the following directives and standards Opus Sp zo o deklaruje z pe n odpowiedzialnoscia e urz dzenie kt rego dotyczy niniejsza deklaracja jest zgodne z postanowieniami nast puj cych dyrektyw UE oraz powi zanymi z nimi normami zharmonizowanymi 2006 95 WE 2004 108 WE EN60950 1 2006 A12 2011 EN55014 1 A1 2009 EN55014 2 A2 2009 EN61000 3 2 A2 2009 EN61000 3 3 2008 Name Nazwa OPUS Sp zo o Address Adres ul Toru ska 8 44 122 Gliwice Type of the machine typ Laminator Model No model cityLAM A3 POLAND Polska Place Signature 01 01 2013 Krystian Nawrat Full Name OPUS User s manual OPUS cityLAM A4 User s guide OPUS cityLAM A3 Healht amp Safety precautions Before operating the equipment please read the Health amp Safety precautions manufacturer recommendations and the operation manual The operation manual should be easily available at any time for the operator The equipment should be installed on sturdy and level surface near a 220 240 V 50Hz socket The equipment should be protected against dust and moisture The equipment must not be placed near the heating or ventilation units The equipment must not be used in vicinity of inflammable liquids or gases The power supply cabl
3. document e Choose correct thickness and type of pouch Put the document into the pouch NOTE It is recommended to leave approx 3mm margins all around the document from the edge 3 Hot lamination e Open the flap at the back of equipment insert the laminating pouch from the front with the document inside it into the rollers and remember to put the sealed end first e The pouch document will move through the unit and exit at the back e Ifthe lamination is not good you can repeat laminating or change settings e After one hour in stand by mode the machine will turn off automatically 4 Cold lamination e Plug the equipment into the power socket and turn on by pressing the button Choose proper option on display for cold lamination e After hot lamination wait 40 60min to cool down the equipment before you start to cold laminate Maintenance and service e Before clearing the equipment remove the power plug from the socket e If the pouch was entangled into the rollers or the laminator does not operate correctly contact the dealer or service team e Push and keep REV button when the laminating material is blocked Technical data Heating system Preheating time Recommended pouch thickness Max document thickness Laminating width Laminating Speed Power voltage Power Rated current Dimensions WxDxH Net weight dokument wraz z folia laminacyjna 14 11 2012 User s guide OPUS cityLAM A3
4. e should be protected against damage and must not be used to pull the equipment or to remove the plug from the socket The equipment must be kept away and out of from reach of children Danger The equipment contains rotary elements Ensure long hair loose jewellery ties and other loose pieces of clothing are keep away they can be get entangled in the rolls The equipment must not be used for any other purposes than those indicated in the instruction manual tis necessary to check and supervise if the equipment is operated correctly In case of any malfunctions you must contact the dealer or service team The equipment must not be located outside and should be operated in a room temperature higher than 8 C Before removing any covers from the equipment remove the power plug from a mains socket Using inappropriate lubricants causes a fire hazard Any repairs must be carry out only by authorised staff The equipment must be operated according to general Health 8 Safety rules Do not leave the equipment in operation without an operator After work it is necessary to turn the equipment off by the switch on unit after the cooling down procedure next remove the plug from a socket Manufacturer s recommendations Use only recommended supplies and accessories Do not put into the laminator documents thickerthan 1 mm The laminated material should always have similar properties Remove the mains plug from t
5. he socket before moving the equipment or during longer none operation If the equipment is switched on and is not operated for more than one hour it can be overheated To avoid bad quality lamination put 2 or 3 sheet of A4 paper through in order to cool the rollers down Always insert the laminating pouch with the close end into the laminator first Putting the open end first can cause bubbling and the film being stuck on the rollers inside the laminator In case of a document being stuck inside the laminator use reverse function REV switch Tailor cut pouch can make the rollers sticky and dirty and wind round them use a carrier Remove all metal elements staples amp paper clips etc before laminating the document NOTE The equipment contains heater elements be aware high temperatures NOTE Not compliance with the rules and recommendations above can void the Guarantee Warranty User s guide OPUS cityLAM A3 Operation 1 Starting the equipment e Plug the equipment into the power socket and turn on by pressing the button e Press the buttons on the touch panel to setup the thickness of pouch required from the range of foil thicknesses from 80mic 200mic The process of heating will start automatically e The heating time for the laminator rollers is 4 6 minutes during this time on LCD display the red diode e When laminator is ready the green diode flashes The equipment is now ready to use 2 Preparing the
Download Pdf Manuals
Related Search