EWP2WIRELESS MOTION DETECTOR
Contents
1. EWP2 User Manual v 1 0 3 INSTALLATION TION manual located at www eldes t download To prevent false alarms avoid installing the unit in the followin g locations Before installing the wireless device we highly recommend to refer to RADIO SYSTEM INSTALLATION AND SIGNAL PENETRA he system should be installed indoors in stationary environment ONLY Choose a location where unauthorised entry is most likely e With the lens facing direct sunshine for instance in front of windows e Places with high temperature fluctuations such as near fireplaces boilers ovens etc e Anywhere with high dust or air flow e Inanarea surrounded by metal or thick walls where the wireless signal may be lost angle 0 TA IN I 5 height x x2 2 5 meters 3 5 m 7 5m 2 3 meters 3m 8m 2 1 meters 15m 9 5m Blind area X1 Secured area X2 1 5 meters Om im angle 10 El E height Ce 2 5 meters 2m 3m 2 3 meters 1 5m 3m 2 1 meters 1m 3 5m Blind area X1 Secured area X2 1 5 meters Om 3m 4 EWP2 User Manual v 1 0 5 a 2 5 meters 25m 7 5m 2 3 meters 2 5m 5 5 m 2 1 meters 15m 6 5m Blind area X1 Secured area X2 1 5 meters Om 4 5m U ile By default EWP2 PCB is in the right position DO NOT change the PCB position in the enclosure When installing EWP2 follow the recomm2. Mechanical Specifications Batten8s inertie stiet neden genden 1 5V Alkaline AA type Number of batteries uus soorsasoorunseronssorranseeranr versen vernanseerneneermeeernnnes 2 Battery operation time 18 months Detection coverage angle 90 Maximum detection distance 10 meters Wireless transmitter receiver frequency anne 868 MHz Wireless communication range Up to 30 meters in premises up to 150 meters in open areas 10 55 C Range of operating temperatures Humidity vee eerste 0 90 RH 0 40 C non condensing DIMENSIONS nnd 124x67x58mm Compatible with alarm systems wie eee ELDES Wireless The operation time might vary in different conditions 2 2 Main Unit and LED Functionality FRONT VIEW BACK VIEW DETECT Q E TAMP 2 BATTERY DETECT E N TAMP 1 BATTERY Do RESET DIS TAMP2 1 el EI LED unit Description DETECT PIR sensors to detect possible intruders Battery slots TAMP1 Front tamper switch RESET Button for restoring default parameters LED Light emitting diode for indication of motion detection if enabled and parameter restoring to default TAMP2 Back tamper switch DIS TAMP2 Pins for back tamper switch management Jumper DIS TAMP2 DIS TAMP2 position _ OO Back tamper Back tamper Address switch disabled switch enabled
3. eldes User manual v1 0 Compatible with e ESIM364 v02 08 00 and up e EPIR3 v1 2 0 and up Main features e Built in dual element passive infrared PIR sensor e Pet immunity against the animals of up to 40 kg e 2 built in tamper switches on the front and on the back of the PCB e Temperature sensor on board EWP2 is a wireless device intended to secure the premises by motion detection Due to the dual element technology of a built in PIR sensor the device features the pet immunity against the animals of up to 40 kg weight in order to prevent them from causing false alarms while moving within the secured premises In addition EWP2 comes equipped with 2 built in tamper switches for sabotage detection In order to start using EWP2 it has to be bound to ELDES alarm system using ELDES Configuration Tool software or by sending a corresponding SMS text message to ELDES alarm system Itis possible to connect up to 16 EWP2 devices to EPIR3 system while to ESIM364 alarm system up to 32 EWP2 devices at a time The maximum wireless connection range is 150 meters in open areas ALLL For complete information on device operation with ELDES alarm system please refer to ELDES alarm system installation manual located at www eldes lt download 1 CONTENTS OF PACK Item Quantity 1 5V Alkaline AA type batteries 2 User manual Screws Jumper EWP2 User Manual v 1 0 2 TECHNICAL SPECIFICATIONS 2 1 Electrical and
4. endations for the installation to achieve the strongest wireless signal B Never install in the following Recommended locations e face the front side of the EL inside the metal cabinet 0 5m to 30 m wireless device towards the inside the building Wireless e closer than 20 cm from the front side of EPIR3 device the metal surface and or 0 5mto150m e keep the distance 0 5 m to power lines i TOREDAT 30 m inside the building 0 5 Wireless EPIR3 m to 150 m in open areas IH device Recommended inside the building e face the front side of the en N wireless device towards the antena 4 2 Co e keep the distance 0 5 m to i 30 m inside the building Wireless Wireless 0 5 m to 150 min open device antenna E areas 1 After a suitable location for your EWP2 is chosen fix the holder to the wall using the screws supplied EWP2 User Manual v 1 0 2 Remove the front cover of the device containing the detector lens an J Pull Z N KENT ct J 4 3 Remove the plastic tab inserted between one of the battery terminals and battery slot 4 Close the front cover of the device see step 2 5 Place the device into the holder K ele K 6 Slide the device down to fix it Matta Ensure that the device is properly fixed into the holder otherwise it will pre
5. levant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at www eldes lt EWP2 User Manual v 1 0 5 D Made in the European Union www eldes lt
6. r The system sends an SMS text message to a preset phone number as soon as the battery level runs below 5 EWP2 User Manual v 1 0 6 RESTORING DEFAULT PARAMETERS Remove any battery from EWP2 Press and hold the RESET button Insert the battery back to EWP2 Hold the RESET button until LED indicator shortly flashes several times Release the RESET button Parameters restored to default nein 7 ADDITIONAL INFORMATION Limited Liability The buyer must agree that the system will reduce the risk of fire theft burglary or other dangers but does not guarantee against such events ELDES UAB will not take any responsibility regarding personal or property or revenue loss while using the system ELDES UAB liability according to local laws does not exceed value of the purchased system ELDES UAB is not affiliated with any of the Internet providers therefore is not responsible for the quality of Internet service Manufacturer Warranty This device carries a 24 month warranty by the manufacturer ELDES UAB Warranty period starts from the day the system has been purchased by the end user The warranty is valid only if the system has been used as intended following all guidelines listed in the manual and within specified operating conditions Receipt must be kept as a proof of purchase date The warranty is voided if the system has been exposed to mechanical impact chemicals high humidity fluids corrosive and hazardous environmen
7. ss The wireless connection loss between EWP2 and ELDES alarm system leads to alarm The system identifies this event as a tamper violation and sends alarm by SMS text message and phone call to the user s by default The SMS text message contains the wireless device model wireless ID code and tamper number U pe The tamper will not operate if the wireless zone is disabled For more details on EWP2 zone and tamper configuration please refer to ELDES Configuration Tool software s HELP section 5 BATTERY REPLACEMENT 1 Open EWP2 enclosure 2 Remove the old batteries from the battery slots 3 Insert the new batteries based on the battery slot positive negative terminals indicated on the PCB printed circuit board of EWP2 4 Batteries replaced For more details please refer to 3 INSTALLATION UT ale Bi 1 5V Alkaline AA type batteries can be used Install only new high quality and unexpired batteries Do not mix the old batter ies with the new ones UT pale H At least 1 battery must be removed if the device is not in use UIN eN B In order to avoid fire or explosion hazards the system must be used only with approved battery Special care must be taken when connecting positive and negative battery terminals Dispose old batteries only into special collection sites Do not charge disassem ble heat or incinerate old batteries APLU The battery status can be monitored in real time using ELDES Configuration Tool software le
8. t or other force majeure factors Safety instructions Please read and follow these safety guidelines in order to maintain safety of operators and people around e DONOT use the system where it can be interfere with other devices and cause any potential danger e DONOT use the system with medical devices e DONOT use the system in hazardous environment e DO NOT expose the system to high humidity chemical environment or mechanical impacts e DONOT attempt to personally repair the system The WEEE Waste Electrical and Electronic Equipment marking on this product see left or its documentation indicates that the product must not be disposed of together with household waste To prevent possible harm to human health and or the environment the product must be disposed on in an approved and environmentally safe recycling process For further information on how to dispose of this product correctly contact the system supplier or the local authority responsible for waste r e disposal in your area Copyright ELDES UAB 2014 All rights reserved It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization by ELDES UAB ELSDES UAB reserves the right to update or modify this document and or related products without a warning Hereby ELDES UAB declares that the wireless motion detector EWP2 is in compliance with the essen tial requirements and other re
9. to calibration process is complete 10 EWP2 is ready for use ALUL If you are unable to bind the wireless device please restore the parameters of the wireless device to default and try again See 6 RESTORING DEFAULT PARAMETERS for more details UT el The auto calibration process initiates as soon as the batteries are inserted into EWP2 device therefore please wait for 2 minutes or longer after battery replacement or restoring default parameters of EWP2 device EWP2 User Manual v 1 0 4 EWP2 ZONE AND TAMPERS Upon successful EWP2 binding process the system adds 1 wireless Instant zone intended for movement detection In case of tamper violation the alarm is caused regardless of system being armed or disarmed There are 2 ways to detect tamper violation on EWP2 e Bytamper switch EWP2 comes equipped with 2 built in tamper switches intended for enclosure supervision one located on the front side of the PCB supervising the front cover in case it is illegally opened see Fig No 1 the other one located on back of the PCB supervising the back side of the enclosure in case the EWP2 is illegally removed from the holder see Fig No 1 and Fig No 13 Once the enclosure of EWP2 is tampered the tamper switch will become triggered This action will be followed by alarm resulting in sending an SMS text message and or phone call to the user The SMS text message contains the violated tamper number By wireless connection lo
10. vent from using the back tamper switch for supervision of the enclosure s back side If you do not wish to use the back tamper switch still please disable it by setting ajumper on DIS TAMP2 pins see 2 2 Main Unit and LED Functionality EWP2 User Manual v 1 0 7 Bind the device to the alarm system using ELDES Configuration Tool software Open Wireless Device Management section and enter the 8 character Device ID located on the EWP2 enclosure or select the device icon with a message NOT CONNECTED indicated next to it and ig ven ar pal al Wireless Device Management Device ID OC21D4FD Add OF ok not connected EWP 1 ID 06280F12 IE TAMPER all Low Esen D rc add OK OK not connected TS gt Radar view amp Tumorr 8 Upon the successful binding process the message indicated next to EWP2 device icon wi unsuccessful try to move EWP2 closer to the ELDES alarm system and bind anew click the Add button The device can also be bound by sending a corresponding command via SMS text message For more details please refer to the software s HELP section and ELDES alarm system user installation manual turn to CONNECTED If the attempt to bind is 9 Move away from the EWP2 motion detection area and wait for 2 minute period or longer while the device auto calibrates its built in PIR sensor DO NOT attempt to test the device before the au
Download Pdf Manuals
Related Search