Home

ICPAGING Application User Manual

image

Contents

1. Chapter Implementing example paging system explaining how to create a simple intercom and paging system using BARIX ICPAGING solution Chapter Additional information explaining how to rescue a device via the serial port how to use the ICPAGING in multimaster environment and providing a quick reference to BARP address bitmap handling and BIN DEC HEX conversion Chapter Dictionary giving a short explanation of some of the most important terms used in this manual EJ Introduction 2 Running ICMASTER 2 1 Booting up PS16 ICMASTER Power up the PS16 If the SonicIP is enabled you will hear the IP which the PS16 got from your DHCP server After that the device will start detecting the USB stick The following message will be shown on the PS16 LCD while the check is being performed Checking USB sanity When the check was successful the ICMASTER idle message will be displayed IcMaster FDX 1 02 04 07 2012 16 keys In case of broken or missing USB stick the application will display an error message and will exit Bad USB stick fs In this case please power off the PS16 remove the two screws from the bottom open the cover and replace the USB stick with a new one formatted with FAT32 file system Also have in mind the following important notes NOTE 1 If you plan to use the ICMASTER on Annuncicom 100 200 please plug in a formatted USB stick otherwise the application will not start NOTE 2 Depending on your conf
2. EZ Running ICCLIENT Min Paging Volume Set here the minimum volume with which to play paging messages If a BGM is playing at volume level lower than this one it will be overloaded BGM level is restored after end of paging message Choose between 0 and 100 in 5 steps Default 50 Maximal BGM Volume Configure here the maximum volume for the BGM you would like the client to be able to set Default setting is 50 3 4 2 4 Outgoing Call Call Masters by Configures the way the master stations are called If set to IP address the masters are called by unicasting the call request command to the master IP If set to ID then the masters are called by broadcasting the call request command with the destination ID master ID Select the needed option so see the corresponding configuration fields Default IP address Master Station ID When Call Master by BARP ID is set enter the system ID of the related 1 to 4 master station The first master station is called after pressing the Button 1 activating the first digital input Default setting is for master stations 1 to 4 respectively 1001 1002 1003 1004 Master Station IP When Call Master by IP Address is set enter the IP address of the related 1 to 4 master station If set to zero uses broadcast to find a master station on the local network The first master station is called after pressing the Button 1 activating the first
3. Key 1 accept an incoming call hang up current call If the master is in a call and another client is ringing pressing this key will hang up the current call Pressing it once again will answer to the incoming call In half duplex mode this key works as a PTT key Press and hold to answer incoming call and start talking release to listen If the handsfree mode is activated then the talk mode can be voice controlled In this case the voice activation level and the time out are configured via the web UI NOTE closing the current call when there is a second incoming call is possible only in FDX mode In HDX mode key 1 is used as a PTT key so in this case only rejecting the incoming call is possible Key 2 page all selected clients if no call is in progress trigger the connected client s relay door open for 5 seconds if a call is in progress Please note this is a PTT Push To Talk button when the handsfree mode is not activated In handsfree mode press this key once to activate the paging mode and once again to stop it The key LED blinks when paging is active Key 3 pressing this key will cancel an incoming call either in idle mode or when the ICMASTER is in a call session with one client and another client is calling If the ICMASTER is in a call and there is no other incoming call pressing this key will also hang up the current call session Key 4 enter unattended mode pressing any other key exits unattended mode Clien
4. Hands Free When set to yes and Half Duplex mode is enabled the talk listen mode can be voice controlled while the ICMASTER is in active call If the voice level exceeds the one set in Input Trigger Level the master is switched in talk mode and the client in listen mode The behavior for paging is also changed the Page key needs to be pressed once instead of press and hold to activate Paging mode and pressed again to stop Default setting is No Input Trigger Level Triggering input audio level if Hands Free mode is selected Accepted range O 32767 Default setting is 1000 Inactivity timeout Sending of the audio stream in Hands Free mode stops after this number of milliseconds of no input audio signal Default setting is 1000 Microphone Gain Microphone gain dB increase if your microphone is too faint decrease if it s too loud or overdriven Default 21 dB e A D Amplifier Gain A D converter preamplification in dB Increase if the audio signal too faint decrease if it s too loud or overdriven Default O dB Default Volume Choose between 0 and 100 in 5 steps EfJ Running ICMASTER Default 5096 2 5 2 4 Incoming Call Call Master by Configures the way the master is being called If set to ID then the call is ignored if the destination ID in the call request is not the same as the one of the master When set to IP Address the master reacts on unicast or broadc
5. IPzator and as well as manual static IP configuration ICGraph PC software full or half duplex for Intercom mode Single or multimaster mode playing paging messages remote switching of client relay 1 8 Supported hardware The ICPAGING solution is designed to run on the following Barix devices e PS16 Paging Station while it is possible to use the PS16 as a client with its 112 available keys 16 available others on separate 48 keys extension s and two line LCD display is the perfect device to be run as an ICMASTER station Annuncicom 200 can be used as a master or as a client Provides mono BGM intercom door relay control and paging endpoint functionality To be used as two buttons ICMASTER it needs an USB stick to run When used as a client the available two wire interface allows the device to use the AIPHONE door stations in half duplex mode Annuncicom 100 can be used as a master or as a client Provides mono BGM intercom door relay control and paging endpoint functionality To be used as two buttons ICMASTER it needs an USB stick to run Exstreamer 100 105 used as client Provides stereo BGM and paging endpoint functionality Introduction Exstreamer P5 used as client Provides mono BGM and paging endpoint functionality combined with 5W amplified speaker output and Volume Source Control VSC port Exstreamer 110 120 used as client Provides stereo BGM door relay control and
6. They can be found on the Internet RFC Description 950 Internet Standard Subnetting Procedure 1700 Assigned Numbers 1117 Internet Numbers 1597 Address Allocation for Private Internets ZY Dictionary 9 Legal Information 2012 Barix AG Zurich Switzerland All rights reserved All information is subject to change without notice All mentioned trademarks belong to their respective owners and are used for reference only Barix and ICPAGING are trademarks of Barix AG Switzerland and are registered in certain countries For information about our devices and the latest version of this manual please visit www barix com Illustration Index Illustration 1 ICMASTER keyboard AVOUT iis o rto eerte adie erreur b rere been Porno E ANAE NEK 11 Illustration 2 ICMASTER home PaQe ccc ne nr Eee ener ener eren ener enne 13 Illustration 3 ICMASTER basic settings page mme 14 Illustration 4 ICMASTER advanced settings page ssssss memes 15 llustration S IGCLIENT home PAGS E 21 Illustration 6 ICCLIENT Application basic settings Web Pagge sssm Hmm 22 Illustration 7 ICCLIENT Application advanced settings Web Page sssssem m 23 Illustration 8 ICgraph application Full duplex eseseeeeenne nnne 29 Illustration 9 ICgraph half duplex Intercom buttons sssseeee ennemis 31 Illustration 10 ICgraph Point butt
7. unattended mode and custom messages recording 2 4 ICMASTER Web home page The device home page is dynamically auto refreshed every second and shows some useful run time application details Illustration 2 ICMASTER home page Home CONFIGURATION STATUS DEFAULTS UPDATE REBOOT Intercom Master Station APPLICATION STATUS BARP Station ID 1001 Current Status IDLE AUDIO LEVELS Input Level 127 dB Output Level 127 dB KEYBOARD LAYOUT 9 10 11 12 13 14 15 16 Select Select Select Select Select Select Select Select Group1 Group2 Group3 Group4 Group5 Group6 Group7 Group8 1 2 3 4 8 5 6 7 Record Rec Play Accept Close Unatt Unatt Custom Cancel Dynamic Call Page Call On Off Message Message Sel Group Under the APPLICATION STATUS section is visible the BARP station ID and the current application status Under the AUDIO LEVELS section input and output audio levels are displayed in dB The section KEYBOARD LAYOUT shows the layout of the keys as supported and used in the current hardware 2 ICMASTER Web configuration pages The configuration of the ICMASTER is very intuitive and easily done via the web UI Example snapshots of the basic settings and advanced settings pages are shown on Illustration 3 and Illustration 7 EE Running ICMASTER 2 5 4 BASIC SETTINGS The BASIC SETTINGS page is accessible clicking the CONFIGURATION button in the top menu it shows the most important
8. DSUB9 RJ45 adapter Plug the adapter in the RS 232 port at the back panel of the Exstreamer 100 screwing it for more reliable connection Reboot the Exstreamer 100 to recognise the newly connected VSC unit Now the VSC unit should be functional After reboot the default BGM channel should be displayed for ex 1 Rotating the knob left right decreases increases the volume Pressing the knob switches to channel mode the rotation changes the channel being played If channel O is selected and the local instreamer is enabled then Lo meaning local channel is displayed In case the local instreamer is disabled Id idle is displayed 5 7 Configuring the PC for BGM distribution 5 7 1 Hardware requirements For music distribution we need a computer that can run the BARIX MP3_RTP_Streamer application which creates several streams from MP3 library Any recent Windows Linux iMac computer running Java VM should work 5 7 2 Configuring the MP3 RTP Streamer Download the MP3 RTP Streamer from the BARIX web site Unzip it in a separate directory and run the MP3 RTP Streamer jar The application window should look like this Barix MP3 RTP streamer MP3_RTP_Streamer cfg 20 0 Channel name_ IP Port Start Stop Playlist File name Song Buffer Status Doub Illustration 14 MP3 RTP Streamer main window unconfigured We re going to configure it to play the 3 BGM channels plus the local channel
9. Enter the 4 values of the desired Static IP e g 0 0 0 0 for a default Netmask depending on the used IP Address 255 255 255 0 for a C class network Gateway IP Adaress Enter the 4 values of the desired Gateway IP address e g 0 0 0 0 for no Gateway or the IP of the gateway in your LAN Note The Gateway has to be set only when connecting to other devices over the WAN through a router Default 0 0 0 0 EH Running ICMASTER Primary DNS In this field you can give the desired primary and alternative DNS IP address to be able to connect to URLs e g www radio com Example 195 186 1 111 Default 0 0 0 0 Alternative DNS In this field you can type the desired alternative DNS IP adaress in case the primary DNS is not reachable Example 195 186 4 111 Default 0 0 0 0 Syslog Address Destination address for syslog messages sent by the BCL program via the SYSLOG command Set this to your syslog logging machine if your syslog messages are recorded centrally If set to 0 0 0 0 syslog messages are broadcasted Default 0 0 0 0 DHCP Host Name Name of the device sent in DHCP request If left empty a name based on the device s MAC address is generated automatically Enter up to 15 Characters Web server port Defines the port where the webserver of the device can be reached If set to O the default HTTP port 80 is used Default Ethernet Port On devices with dual ethernet conne
10. The three BGM channels will stream from ports 10501 10502 10503 while the local channel should be configured at port 10500 Double click at the MP3 RTP streamer window to open the channel add dialog in Nene Create channel 1 Channel na channel IP address p24124 Music lib dir Open lib dir Port 10500 Playlist UL A Stattime px 4 Buffer size 32k Stop time 0 00 te Shuffle o BARP IP 0 0 0 Repeat M BARP Port Dp Update ti Create Cancel Illustration 15 MP3 RTP Streamer configuration dialog Put the channel name first ex Local channel for channel O Set the IP to the multicast group 224 1 2 4 and the port to 10500 Click Music lib dir and navigate to the directory where your mp3 files and playlists reside Click Playlist and select the playlist for this channel The playlists can be created with iTunes WinAmp or any other mp3 capable player 2 This DSUB9 RJ45 adapter is sold separately Please contact BARIX for more information EJ Implementing example paging system Click on Create and repeat all these steps to add channels 1 to 3 using ports 10501 to 10503 Now the MP3 RTP streamer is configured and should be streaming music on address 224 1 2 4 and ports 10500 10503 5 8 Testing the Paging system 5 8 1 Recording a custom message The ICMASTER allows the user to pre record an announcement to be sent when desired t
11. door station A PC for streaming music BARIX MP3_RTP_Streamer application 5 2 System layout Let s implement an example system for the needs of a small shop The proposed layout is shown on the figure below Illustration 11 Example intercom and paging system PS16 Ann100 a ID 1001 ID2 f TE ZEN mem Ann200 4 f Ful duplex ID 1 Exstr100 LAN WAN D3 jg AIPHONE VSC amp IR Tg IE JA Door Pu control unit Los Panel T m nee PC running MP3 RTP Streamer 7 eae mE 28 Start port 10501 oS We will need one Master station for sending messages and controlling the background music that will be located at the security room one station for delivering high quality music in the shop area Stereo speakers EJ Implementing example paging system one door station at the stock delivery entry and one telephone at the cash desk The music delivery is done by a PC running the BARIX MP3 RTP Streamer but could be also done with a BARIX Instreamer device The BGM playback can be controlled by the ICMASTER or locally using the HAI Volume Source Control unit For the door station BARIX Annuncicom 200 is being used as it provides the suitable two wire interface for connecting the AIPHONE panel As this device is half duplex the whole system needs to be configured in half duplex mode 5 3 Configuring the master station 5 3 1 Initial setup Get the latest version of the ICPAGING ABCL software from BARIX dow
12. is defective Check the volume level client Audio gt Default Paging Volume master Audio gt Default Volume fields to be greater than O Check also mic and speakers to be well connected to the device Audio corrupted Client device has an audio format set different from the master Check Audio Format field under CONFIGURATION gt Advanced Settings gt Audio section All devices in the system MUST have the same audio format set Annuncicom 100 200 master device not working USB key is not connected to the device Insert a USB key ICCLIENT locked in PAGING state Master could have been rebooted while paging Once master is up re page locked devices and close the paging session Device not responding in the serial update process Another PC task can be holding the serial port Check for other PC programs tasks using the same serial port and terminate them Restart the update procedure ET Troubleshooting 8 Dictionary 8 1 1 DHCP Short for Dynamic Host Configuration Protocol a protocol used to assign an IP address to a device connected to a Network 8 1 2 FDX Short for Full Duplex A full duplex system allows communication between two parties to be done in both directions simultaneously See this Wikipedia article for more information 8 1 3 HDX Short for Half Duplex In a half duplex system simultaneous communication in both dir
13. like MP3 RTP Streamer ICGRAPH BARP paging client priority based audio messaging easy WEB based configuration multiple master configuration call all masters and call failover scenarios ICMASTER full or halfduplex mode of operation handsfree mode for sending paging messages and half duplex communication up to 112 available keys with two 48 keys extensions configurable audio messages priority intercom client call master caller ID display configurable ringtones per client Introduction till 8 configurable single or group target buttons paging up to 128 devices 1 dynamic group configurable unattended mode timeout configurable call reject mode for multimaster environment recordable unattended mode message recordable custom message control of local and clients volume client background music BGM channel control 10 100 Mbit Ethernet connection supports automatic network configuration BOOTP DHCP IPzator and as well as manual static IP configuration ICCLIENT full or half duplex mode of operation Single or multimaster mode playing paging messages intercom to master supports the HAI Volume Source Control unit and IR remote control background music BGM playback and control background music playback in mp3 format AIPHONE door panels support 10 100 Mbit Ethernet connection supports automatic network configuration BOOTP DHCP
14. mode in order not to override the preconfigured relay behaviour Default always off LED Status Configures the device front panel led behavior for the devices that have a led panel Default is Input State 3 4 2 8 Security This section is the same as in ICMASTER See ICMASTER 2 5 2 7 Security section Running ICCLIENT 4 Running ICgraph 4 1 About ICgraph ICgraph is a Java based PC software It requires a Java Runtime Environment JRE installed on the PC to run properly Such JRE is available for almost all operating systems See www java com ICgraph is a free Barix software when used together with Barix hardware products This software is freely configurable over the ICgraph cfg file It allows to control ICPaging devices and communicate to it The ICPAGING firmware package contains two different ICgraph configurations one for half duplex and one for full duplex These configurations can be modified from you if needed For more information about ICgraph check the ICgraph manual available on www BARIX com 4 2 How to run ICgraph The ICPAGING software package contains a sub folder ICgraph Master there are two different ICgraph configurations stored one for full duplex and one for half duplex Before you can start ICgraph make sure the Java JRE is installed see www java com on your PC If Java is installed then decide which mode full duplex or half duplex you will use for Intercom communication
15. options to be set up for a quick configuration Illustration 3 ICMASTER basic settings page uou conricuraTion status DEFAULTS UPDATE REBOOT Annund Intercom Master Station Current Profile PS16 FD BASIC SETTINGS Help BARP Station ID 1001 ulmi ram BAR Oo o Hands Free Yes No clien Apply Cancel mes mE Defar Group 1 Address Map View Modify 10 clients selected Dupli Choc Defa Han Whe the t If the Inpu in tal The Page of pre and Defai BARP Station ID Enter here the BARP system ID of this master station The ID is used from the clients to identify the source of the control messages in multimaster environment Default is 1001 Duplex Mode Choose the desired mode of operation Default setting is Full Hands Free When set to yes and HDX mode is enabled the talk listen mode can be voice controlled while the ICMASTER is in active call If the voice level exceeds the one set in Input Trigger Level the master is switched in talk mode and the client in listen mode The behavior for paging is also changed the Page key needs to be pressed once instead of press and hold to activate Paging mode and pressed again to stop Default setting is No Group 1 Address Map Allows to set up the first group 1 of destination targets Click related View Modify button to setup the group A label on the right shows the number of selected clients in this group De
16. some cases forgot web UI password loading corrupted FW image etc the access to the web UI of the ICMASTER may be lost In such a situation the one of the possible recovery solutions on the BARIX devices is to press and hold the reset button while powered on The device will revert to factory defaults and reboot However since PS16 stations do not have HW reset button this procedure is not applicable In this case follow the procedure below to revert to factory defaults Press and hold key 1 lower left at startup A message will appear on the display asking you to confirm To confirm press key 16 upper right within 3 seconds without releasing key 1 3 Rescuing the PS16 using the serial port is more complex and requires some engineering work Please contact BARIX Support to get more information 4 Another recovery solution is to do a serial rescue using the serial port see section Updating a divece using RS 232 serial port EX Additional information otherwise the unit will continue booting normally After confirming and releasing all keys the factory defaults are restored and the unit reboots Listen to the SonicIP and note down the IP address Open the web page at the announced IP address and change the application from ICCLIENT to ICMASTER Click Apply to reboot After reboot reconfigure the ICMASTER as it was before 6 3 Configuring ICPAGING in multimaster environment In some cases m
17. the stereo music player 5 6 1 Initial setup Do the initial setup as described in the ICMASTER General settings section After uploading the SW if the default running application is ICMASTER click REBOOT menu button and under the Reboot as drop down list select Intercom Client and click Reboot 5 6 2 General settings Now it is time to configure our door station As has been done for the master station once Exstreamer 100 is rebooted open CONFIGURATION and then Advanced Settings page and setup the desired options int the Network Settings section In addition also set the serial port to be used for the VSC I O Control section Serial Port Select VSC Panel 5 6 3 BGM player settings BARP Control section Station ID Set the client ID 3 Background Music section BGM Broadcast Address Set to use multicast address 224 1 2 4 Background Music section BGM First Broadcast Port Set to 10501 Background Music section Available BGM Channels Set to 3 Background Music section BGM Start Channel Set to 1 5 6 4 Connecting the Volume Source Control VSC unit Unpack the VSC unit from the supplied box Turn it upside down Take a small flat tip screwdriver and set the arrow of the yellow switch to point to 1 Take a LAN cable with the necessary length and plug it in the VSC RJ 45 socket Efl Implementing example paging system Connect the other end of the LAN cable to the
18. with the clients and select the according sub directory and start the ICgraph jar file from this directory ICgraph can be used as single master or together with other Masters but in multimaster mode the behaviour is a little bit different than using the ICMaster devices 4 3 Usage of ICgraph The ICgraph configuration shows per default 8 groups or 80 client configured with Ids from 1 80 and some more function buttons You can change the view and display group buttons and or point buttons Illustration 8 ICgraph application Full duplex 2 05 2012 06 xd Fullduplex Intercom Master Station 120713 081621 BAR IH Intercom Show group show member Show member show member show member show member Show member Show member Mute ON Relay open Show events Show LOG Show records Play message Start record ICpaging Fax v10 When ICPaging devices in the network are properly configured then they will be discovered after maximum 30 seconds from ICgraph and the according point button will change the color from BE Running ICgraph dark grey to white The white point buttons can be used for other actions on ICgraph If a device is not more reachable in the network e g turned off or not connected then the point button will change the color of this po
19. 0 0 0 0 0 0 0 0 0 Hex A A 0 Wlustration 16 Address bitmap encoding To find out in which byte is the client ID we would like to select we use the integer division operation IDbyte Client ID 1 8 Let s see what it means in terms of our example Let s find in which byte is our client ID 21 Idbyte 21 1 8 2 The result is the biggest number which multiplied by 8 does not exceed ID 1 The other result from this operation is called reminder and is in fact the number that completes to ID 1 ID 1 result 8 reminder Now to find which bit within this byte we take the reminder which for ID 21 is 4 from the integer division and subtract it from 7 In other words IDbit 7 4 3 which means that we have to set bit3 from byte2 ByteO Byte1 Byte2 Client Ids 1 8 Client Ids 9 16 Client Ids 17 24 Bits 7 6 54321 0 7 6 54321 0 7 6 543210 Enable Disable 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0 Hex 0 0 0 0 8 8 Repeating these calculations for client ID217 we find that bit of byte2 has to be set Looking at the 6 5 BIN DEC HEX conversion table we see that 1000 is Ox8 in HEX format which explains the 0x88 value we see for group 1 in the Group buttons address bitmap summary 6 5 BIN DEC HEX conversion Hexadecimal digits have values from 0 15 represen
20. BAHIX THE VOICE OF SIMPLICITY ICPAGING Application User Manual ICPAGING intercom and paging system ICPAGING ABCL FW version VA1 08 Doc release version 28 09 2012 ICMASTER VO1 07 ICCLIENT V01 05 ICGRAPH Master HD configuration V1 0 ICGRAPH Master FD configuration V1 0 REVISION TABLE Date Version Who Change 09 07 12 Draft AD First draft 10 07 12 Draft SG Added ICgraph chapter 28 08 12 1001 AD Updated for IcPaging 1 05 30 08 12 002 AD Updated for IcPaging 1 06 10 09 12 003 AD Updated for IcPaging 1 07 28 09 12 004 AD Updated for IcPaging 1 08 Table of Contents l IntroductiOn ssesseccescssssscccceccssscccssecececesessssececcesesscsseseseceecee 7 LI About ICPRAGING pana 7 1 2 Fee CSS oe e aaa cae dia bae dde Loon Z 1 3 Supp tt d hakdwake os ioci tor iuret esci eire e used 9 1 4 Additional doCFTents uaioica clesia ta coca ossis ttis Il ICPAGING ABCL Firmware 22 PST Keyboard Layout peores 14 2 3 Running ICMASTER on Annuncicom 100 200 PS 17 2 4 ICMASTER Web homte page iiiicte e ciatis setuacsssbsass 18 2 5 ICMASTER Web configuration pages tita taeteie intestatus 19 25 1 JBASIG SETTINGS i aiias 2 5 2 _ ADVANCED SETTINGS 4 Running ICgraph eee eee ee eee ee eene eee ee e e e ee eee ese 41 4 1 About I
21. C ip Riss ue tania dis act icti toin cud 4l 5 32 General Settlligs ununi esc coo etai ctio ioa 49 5 3 3 ICMASTER StM ean 49 5 63 BGM player settings 5 64 X Connecting the Volume Source Control VSC unit 5 8 Recording a CUStOMm Message eeraa 56 5 8 2 R jeetihig axcalliscacusctese cese odes essi oie OE OTT 56 5 8 3 Anwer call oie it 56 Voi NEN AI RR 57 5 8 5 Paging thie custor Message aus e cicer sitne concebir 57 6 Additional information ES ITI NUS 58 6 1 58 6 3 Configuring ICPAGING in multimaster environment 59 6 3 1 Call Failover SCenablo iiau ditio a a eec dcc aus 60 6 3 2 Call all masters SCenallba sn casonicsoi a cen c G c da 60 6 3 3 Call AlL fallover SCenab lO ac o et e abu buceo ca 60 amp LA Class A TIG WOFN aiite icit sa ct haoc eis cras tonic c 67 8 1 12 Class B fietWorl e e uc s d c s ie a c cic 67 amp LI Class CBSEWODI ie natos ale ci rii etn aiat 68 S Lb Class D networkin e224 ci cc e e ive rb cte 68 Sah Se Class E netWobls uui acc s ii nca c et at eid 68 amp L6 Network Addtessuu uasa t acere isto S eti te ie iet tun rue ue 68 8 1 17 Broadcast Addresses ice tat rie e eic ildd 68 8 1 18 IP letmiask ioni cto iiit eta en ti ti icai cette t eese iiie 69 8 1 19 Private IP Networks and the Internet s
22. and C Entering a Netmask it is possible to define how many bits from the IP address are to be taken as the network part and how many bits are to be taken as the host part Standard IP network Netmask Class Network bits Host bits Netmask A 8 24 255 0 0 0 B 16 16 255 255 0 0 C 24 8 255 255 255 0 Netmask examples Netmask Host bits 255 255 255 252 255 255 255 248 255 255 255 240 255 255 255 224 255 255 255 192 255 255 255 128 255 255 255 0 255 255 254 0 9 255 255 252 0 10 255 255 248 0 11 o Oo oO A C N EH Dictionary Netmask Host bits 255 128 0 0 23 255 0 0 0 24 8 1 19 Private IP Networks and the Internet If your network is not connected to the Internet and there are no plans to make such a connection you may use any IP address you wish However if you are not connected to the Internet and have plans to connect to the Internet or you are connected to the Internet and want to operate your Barix Barionet on an intranet you should use one of the sub networks below for your network These network numbers have been reserved for such networks If you have any questions about IP assignment ask your Network Administrator Private IP networks by class Class Network A 10 X x X B 172 16 x x C 192 168 0 x 8 1 20 Network RFC s For more information regarding IP addressing see the following documents
23. asted call requests The destination ID check is ignored in this case Default is IP address Unattended Mode Enables or disables the unattended mode When enabled the Unattended Timer becomes visible and can be configured Disabling the unattended mode is recommended when using the master in a multimaster environment because if any of the masters is in unattended mode it may always pickup the incoming call thus preventing the other masters to get the call When disabled pressing the unattended mode key enters the master in a Call reject mode Default is Enabled Unattended Timer Configures the number of seconds after the device switch to unattended mode during a call Minimum value allowed is 3 maximum is 60 Default is 20 2 5 2 5 Paging Group Address Map Allows to set up the related group of destination targets Click related View Modify button to setup the group A label on the right shows the number of selected clients in this group Note only available groups supported from the current keyboard layout are displayed Default setting is starting from group 1 10 clients selected for every group for group 1 id s 1 to 10 are selected group 2 id s 11 to 20 selected group 8 id s 71 to 80 selected Audio Multicast Socket Configures the multicast group socket as IP PORT for paging As IP it has to be within the range 224 0 0 0 239 255 255 255 If set to 0 0 0 0 then the default broadca
24. belongs to An IP address has two components the network address and the host address For example consider the IP address 150 215 017 009 Assuming this is part of a Class B network the first two numbers 150 2 represent the Class B network address and the second two numbers 017 009 identify a particular host on this network The Netmask would then be 255 255 0 0 8 1 8 Static IP A Static IP is a fixed IP address that you assign manually to a device on the network It remains valid until you disable it EE Dictionary 8 1 9 VSC Volume Source Control unit This an universal wall mountable control accessory for the Barix audio products range It provides two digit LED display control knob and a IR port 8 1 10 IP Addressing An IP address is a 32 bit value divided into four octets of eight bits each The standard representation is four decimal numbers in the range of 0 255 divided by dots Example 192 2 1 123 This is called decimal dot notation The IP address is divided in two parts a network and a host part To support different needs five network classes have been defined Depending on the network class the last one two or last three bytes define the host while the remaining part defines the network In the following text x stands for the host part of the IP address 8 1 11 Class A network P address 1 x x x to 127 x x x Only 127 different networks of this class exist These have a v
25. ch the client may listen for any incoming audio No BARP messages are checked for this port so any audio arriving at this port will be played immediately This can be used as a Broadcast to all feature Default setting is No 3 4 2 3 Audio Audio Format Choose between different encoding types and sampling frequencies u law or A law at 8 or 24 kHz Default setting is u law 8 kHz IMPORTANT make sure to use the same encoding on ALL devices of the ICPAGING system Input Source Choose the desired input source Default setting is Mic Duplex Mode Choose the desired mode of operation If Half is selected the communication is controlled from the ICMASTER Default setting is Full Use Al_Phone This setting is for Annuncicom 200 hardware only which provides support for Al PHONE two wire interface Set to Yes if Al Phone is used as a door station In this case Half operating mode is recommended Default setting is No Microphone Gain Microphone gain dB increase if your microphone signal is too faint decrease if it s too loud or overdriven Default 21 dB e A D Amplifier Gain A D converter preamplification in dB Use this setting to achieve the right balance to your connected equipment Increase if the audio signal too faint decrease if it s too loud or overdriven Default 0 dB Default Paging Volume Choose between 0 and 100 in 5 steps Default 50
26. ction this parameter selects the default port to be used In most cases selecting ETH1 is suitable however some devices e g the PS16 provide Power over Ethernet PoE functionality on ETH2 If you change this parameter do not forget to connect the ethernet cable to the proper port on the rear of the device NOTE on devices with a single ethernet port select always ETH1 Selecting ETH2 makes the device inaccessible Default ETH1 SNMP System Name SNMP MIB entry for system name system sysName 0 Default empty SNMP System Location SNMP MIB entry for system location system sysLocation 0 Default empty IJ Running ICMASTER SNMP System Name SNMP MIB entry for system contact system sysContact O This parameter can be queried using any SNMP browser but can not be updated Default empty 2 5 2 2 BARP Control BARP Station ID Enter here the BARP system ID of this master station The ID is used from the clients to identify the source of the control messages in multimaster environment Default is 1001 Paging Priority Enter here the priority of the audio messages sent by this master station This setting is useful in multimaster environment when a client receives audio messages from many masters simultaneously In this case the client will play the stream with the highest priority The priority must be in the range 1 254 Priority O the highest is reserved for emergency priority por
27. digital input Default setting is 0 0 0 0 Call next Master If set to Yes the client is forced to call the next master in the list if the one that it is currently calling is not responding for example because of network problems or power failure of the master The call to the next master is activated after the expiry if the auto hang up timeout In this case the call ring timer is restarted when the client starts calling the next master Default No Auto Hang Up EH Running ICCLIENT Configures the number of seconds after which the client will stop ringing if the master is not responding Minimum value allowed is 3 maximum is 60 Make sure this value is greater than the unattended mode timeout set for the ICMASTER otherwise the ICCLIENT will not get the unattended message from the ICMASTER Default 20 3 4 2 5 Background Music BGM Broadcast Address Enter the broadcast multicast address of the background music streaming server If set to 0 0 0 0 then broadcast is used Default setting is 0 0 0 0 BGM First Broadcast Port Enter the broadcast multicast port of the first channel background music streaming server The BGM streaming could be provided by multiple streamers but they have to be configured to use consecutive port numbers If set to O the BGM functionality is disabled Default setting is 11001 BGM Available Channels Enter the number of the available background music c
28. e Keys 17 112 select client ID 17 112 Important note When the ICMASTER is run in HDX mode pressing key 1 when there is an active call will not close it In HDX mode key 1 is used as PTT Push To Talk key When pressed the microphone of the ICMASTER is switched ON the speaker turned OFF while the mic of the ICCLIENT is automatically switched OFF and its speaker turned ON 2 3 Running ICMASTER on Annuncicom 100 200 PS1 The ICMASTER can be used also on the Annuncicom 100 200 and PS1 devices with limited functionality Because on these devices there are only two available keys the key mapping is a bit different than the one described for the PS16 Full duplex FDX mode Key answer incoming Close current call Key2 if it is in a call pressing this key will open the relay on the client for 5 seconds When the EE Running ICMASTER ICMASTER is in idle mode pressing key 2 will start paging to Group 1 Half duplex HDX mode Key 1 answer incoming call While the call is active it works as a PTT key press and hold to talk release to listen Key2 if it is in a call pressing this key will open the relay on the client for 5 seconds When the ICMASTER is in idle mode pressing key 2 will start paging to Group 1 Press and hold key 1 then press key 2 Close the current call In addition as the PS1 device does not have USB port all features that use it are disabled customized station ring tones
29. e message has been sent the ICMASTER will return to idle mode The LED will blink while sending and the BGM playback should be restored after the message is sent Implementing example paging system 6 Additional information 6 1 Updating a device using the RS 232 serial port Sometimes when the device is not accessible via the LAN or the image in the flash memory is corrupted for some reason then a serial rescue may be needed to reset the device to the factory defaults So here are the steps that need to be executed to do the serial rescue e Disconnect the device from the power supply Connect the COM port of the device to the COM port of your computer via a null modem serial cable Open a terminal in the update rescue directory in your unzipped copy of the ABCP ICPAGING firmware If using Linux or Mac switch to update rescue linux directory Start the rescue process by executing serialX where X is the number 1 4 of the serial port on the computer If running on Linux Mac execute the seriald sh script giving the device name of your COM port as a parameter For ex seriald dev tty UC 232AC e Power on the device and wait for the update to finish The device will reboot automatically NOTE All other settings except the network settings will be lost 6 2 Restoring Factory Defaults of PS16 This new feature has been added as a software replacement for the missing reset button in PS16 stations In
30. ections is not possible i e if one of the parties is sending the other have to wait it to finish before replying See this Wikipedia article for more information 8 1 4 IP Short for Internet Protocol the IP is an address of a computer or other network device on a network using IP or TCP IP Every device on an IP based network requires an IP adaress to identify its location or address on the network Example 192 168 2 10 8 1 5 IPzator Barix IPzator technology is designed for the purpose that the Barix device can create its own IP address according to the network structure in case it can t receive one from your network If DHCP AUTOIP or BOOTP fail IPzator will create an IP address within the subnet and test it starting with x x x 168 and if occupied incrementing by one If the address works and is not being used by another device on the network it will give the address to the Barix device 8 1 6 MAC address Abbreviation for Medium Access Control a MAC is a unique address number formatted in hexadecimal format and given to each computer and or network device on a computer network Because a MAC adaress is a unique address a computer network will not have the same MAC address assigned to more than one computer or network device Example A1 B2 C3 D4 E5 F6 8 1 7 Netmask A number used to identify a sub network so that an IP address can be shared on a LAN Local Area Network A mask is used to determine what subnet an IP address
31. equest command sent from the client 6 3 3 Call all failover scenario Configured as call all masters scenario However if there is one master in a call reject mode the client will get the reject and start calling the other masters in the list by sending unicast call requests The masters that got the broadcasted call request shall stop ringing 6 4 Understanding BARP address bitmaps According to BARP protocol the address bitmap is 128 bytes allowing to address client IDs 1 1024 starting from 1 client IDZO is not valid In the ICMASTER application because of the limited memory space in the EEPROM only the first 16 bytes can be stored thus allowing to group select only the first 128 client IDs Each byte addresses 8 clients for ex byte O addresses clients IDs 1 8 byte 1 addresses client IDs 9 16 etc Setting a bit within a byte enables the corresponding client clearing the bit disables it However the client IDs within a byte are stored in reversed order i e the smallest ID is stored in the MSB the biggest at the L SB The composed address map is then transmitted with the smallest EX Additional information byte numbers first as shown on the picture below ByteO Byte 127 Client Ids 1 8 bits 7 0 Client Ids 1017 1024 bits 7 0 Bits 7 0 5 4 321 0 5 7 5 4 3 2 Client ID 112 3 4 5 6 7 8 1017 1018 1019 1020 1021 1022 1023 1024 Enable Disable 1 0 1 0 1 0 1 0
32. ery large number of potential connected devices up to 16 777 216 Example 10 0 0 1 network 10 host 0 0 1 8 1 12 Class B network P address 128 0 x x to 191 255 x x These networks are used for large company networks Every network can consist of up to 65534 devices Example 172 1 3 2 network 172 1 host 3 2 8 1 13 Class C network P address 192 0 0 x to 223 255 255 x Class C networks are most common and for smaller companies These networks can consist of a maximum number of 254hosts Example 192 7 1 9 network 192 7 1 host 9 8 1 14 Class D network The remaining addresses 224 x x x 239 x x x are defined as Class D and are used as multicast addresses 8 1 15 Class E network No addresses are allowed with the four highest order bits set to 1 240 x x x 254 x x x These addresses called class E are reserved EZ Dictionary 8 1 16 Network Address The host address with all host bits set to O is used to address the network as a whole for example in routing entries Example 192 168 0 0 Network addresses can not be used as a host address 8 1 17 Broadcast Address The address with the host part bits all set to 1 is the broadcast address meaning for every host Example 192 168 0 255 Broadcast addresses can not be used as a host address 8 1 18 IP Netmask The Netmask is used to divide the IP address differently from the standard defined by the classes A B
33. fault setting is id s 1 to 10 selected Ef Running ICMASTER 2 5 2 ADVANCED SETTINGS Illustration 4 ICMASTER advanced settings page Home __conricurarion STATUS DEFAULTS UPDATE REBOOT J Intercom Master Station Current Profile PS16 FD NETWORK SETTINGS Use SonicIP O yes 9 No Basic Settings IP Address 192 168 o fis Advanced Settings Netmask 0 0 0 J o BARP Control Gateway IP Address 0 o fe o EDU Primary DNS o p 9 9 Incoming Call Alternative DNS o J fo J o J fo VO Control Syslog Address o Je J e J o jJ Security DHCP Host Name Apply Cancel Web Server Port 80 Default Ethernet Port ETH1 2 SNMP System Name J SNMP System Location SNMP System Contact J The ADVANCED SETTINGS page is accessible by clicking the Advanced Settings button in the left menu it contains and allows to configure all the application options organized in specific subsections The advanced settings page shows all the configurable options 2 5 2 1 Network Use SoniclP If set to yes the device will announce its IP address over the audio output when the device boots up Default setting is yes IP Address Enter the 4 values of the desired device IP address e g 0 0 0 0 for automatic discovery DHCP Bootp IPzator AutolP or a specific IP for an internal LAN Default value 0 0 0 0 Netmask
34. hannels If set to O and no local streamer is defined then no BGM will be played Default setting is 0 BGM Start Channel 3 4 2 6 Serial Enter the background music channel to start playing after a reboot If it more than the available channels it is assumed to be 0 No BGM at startup Default setting is O Serial Port Selects the way the device serial port will be used Select VSC Panel here to use Barix VSC accessory with this application Default Intercom Client Software 3 4 2 7 I O Control Relay 1 Control Set here the default relay behaviour Available values are always off the relay is off in all states idle BGM playback paging and intercom on while in a call the relay is normally off but when the client is in intercom state the relay automatically switches on EJ Running ICCLIENT always on off while in a call this is the inverted version of On while in a call Setting The relay is normally switched on and off when the client is in a intercom state on while in PA mode the relay is normally off but when the client is receiving paging message the relay automatically switches on on while receiving audio stream the relay is normally off but when the client is receiving audio stream either in intercom or PA mode the relay automatically Switches on Note Please have in mind that the BARP relay control command is ignored when the relay is not in always off
35. ications The ICMASTER and ICCLIENT are guaranteed to work only when they are from the same ABCL ICPAGING package Using ICMASTER and ICCLIENT from ICPAGING packages with different versions may not work correctly since new functionality are continually being developed 1 0 About this manual 1 0 4 Links to chapters References to chapters e g X Chapter name are red and underlined and serve as direct links when viewed in Adobe Acrobat Viewer Click on the link to jump to the referenced chapter click on the left arrow icon to jump back to where you came from 1 6 2 Bookmarks pane in Adobe Acrobat The complete Table of Contents is available in Adobe Acrobat Viewer Click on the Bookmarks pane tab on the left side of Adobe Acrobat Viewer to open it Click on any bookmark to directly 1 The built in IR receiver of Exstreamer 110 200 is not accessible from BCL ABCL applications like ICPAGING can use the BARIX external IR dongle or the IR receiver of the Volume Source Control unit FJ Introduction jump to the corresponding part of the manual 1 6 3 Chapter overview This manual is divided into the following chapters Chapter Running ICMASTER describing the functionality provided by the ICMASTER the key mapping and the usage of the web configuration Ul Chapter Running ICCLIENT giving an overview of ICCLIENT usage and configuration Chapter Running ICgraph mentioning what is ICgraph and how to use the ICgraph master
36. iguration the following files may be present on your USB stick UNATTSND this is the recorded unattended mode message CUSTMSG this is the recorded custom message TEST USB an empty temporary file created during USB stick check x MP3 station ID specific ring tone files where xxx is the station ID for example 002 mp3 is the ring tone for station ID 2 None of them is required for the application to boot but it is advised to backup these files without the TEST USB as it will be deleted and recreated during boot and copy them to the new USB stick to keep the same configuration 2 2 PS16 Keyboard Layout The PS16 Paging main unit has 16 functional buttons a flexible microphone speaker and 2 line LCD Optional extensions with 48 keys can be attached on the right side of the PS16 main unit Key layout for PS16 as well as for every master device is shown in the web UI home page as in Illustration 1 ET Running ICMASTER Illustration 1 ICMASTER keyboard layout 9 10 11 12 13 14 15 16 Select Select Select Select Select Select Select Select Groupl Group2 Group3 Group4 Group5 Group6 Group7 Groups 1 2 3 4 7 8 5 6 Record Rec Play Accept Close Unatt Unatt Custom Cancel Dynamic Call Page Call On Off Message Message Sel Group If a PS16 extension is connected key 17 bottom left corner to key 64 top right are assigned respectively to targets 17 to 64 The key functions are the following
37. int button from white to dark grey within 60 seconds Buttons on ICgraph window Show group Show member toggles view between point and group Intercom allows bi directional communication with a single point point must request ring before Clear All resets active communication and or point buttons to normal state Must be used to finish every communication from and with ICgraph Start Paging Stop Paging allows to make paging announcements to selected points and or groups For use this function one many or all points groups should be selected before clicking the Start Paging button Mute ON Mute OFF mutes unmutes the ICgraph PC microphone Relay open allows switching of the remote relay for 3 seconds on selected device Works only during Intercom mode Menu OFF Menu ON displays or hides menu buttons below this button Show events Hide events displays or hides event window the event window is a helpful tool which shows all current point activities Show LOG Hide LOG displays or hides LOG window this window displays all ICgraph activities even the background activities Show records Hide records displays or hides Record window this window shows all recording you made with ICgraph or from the sub folder RECORDS From here window select recordings or self made audio files can be sent to the selected devices Play message Stop message allows to stream a pre recorded file to the selected points The defau
38. ion page The device will reboot click Close to exit address map configuration page NB Do the group key assignment after you have applied all other ICMASTER settings Otherwise the changes will be lost and only the group mask will be saved After reboot click CONFIGURATION and Advanced Settings button and check if the number of the selected clients for the groups is correct It should look like this Illustration 13 Group buttons address bitmap summary PAGING Group 1 Address Map View Modify 1 clients selected Group 2 Address Map View Modify 1 clients selected Group 3 Address Map View Modify 1 clients selected Group 4 Address Map View Modify 3 clients selected For more detailed explanation on the address bitmap configuration values see sections Understanding BARP address bitmaps Implementing example paging system Paging section Audio Multicast Socket Configure 224 1 2 3 leave the default port as 12345 Leave all other settings to their default values and click Apply With this the ICMASTER station configuration is finished 5 4 Configuring the door station 5 4 1 Initial setup Do the initial setup as described in the ICMASTER General settings section After uploading the SW if the default running application is ICMASTER click REBOOT menu button and under the Reboot as drop down list select Intercom Client and click Reboot 5 4 2 General settings Now it is time to configure our do
39. ivation change to Intercom Talk yellow in this mode you can talk to the ringed selected device To listen to the device click on the Intercom Talk button The button name will change not to Intercom Listen green Illustration 9 ICgraph half duplex Intercom buttons Clicking on the Intercom Listen button with change again to Intercom Talk button To finish the communication press the Clear All button Note for Intercom only one ringing device should be selected at the same time no Groups and not multiple devices If the device is not ringing anymore then the point button will stay in magenta none blinking In this mode only a one way communication to the device for max 10 seconds is possible when using the Intercom button Illustration 10 ICgraph Point button states undiscovered ringing activated selected EN NE 199 discovered rang EJ Running ICgraph 5 implementing example paging system 5 1 Necessary components For better understanding the usage of ICPAGING solution proposed by BARIX we will try to implement a small paging system supporting all the advertised features For the system shown below the following components are needed BARIX Annuncicom 200 BARIX Annuncicom 100 AIPHONE door panel PS16 Paging station One PS16 48 keys extension optional BARIX Exstreamer 100 A pair of powered stereo speakers A telephone style
40. key is also pressed clears also the address bitmap assigned to it Key 8 select assign dynamic page group If there is currently no address bitmap assigned it grabs the current selection when pressed To clear the bitmap press and hold this button then press the cancel key Key 9 select page group 1 The address bitmap assigned to this key is configured from the related ICMASTER web UI address map configuration page Key 10 select page group 2 The adaress bitmap assigned to this key is configured from the related ICMASTER web UI address map configuration page Key 11 select page group 3 The address bitmap assigned to this key is configured from the related ICMASTER web UI address map configuration page Key 12 select page group 4 The address bitmap assigned to this key is configured from the related ICMASTER web UI address map configuration page Key 13 select page group 5 The address bitmap assigned to this key is configured from the related ICMASTER web UI address map configuration page Key 14 select page group 6 The address bitmap assigned to this key is configured from the related ICMASTER web UI address map configuration page Key 15 select page group 7 The address bitmap assigned to this key is configured from the related ICMASTER web UI address map configuration page 4 Key 16 select page group 8 The address bitmap assigned to this key is configured from the related ICMASTER web UI address map configuration pag
41. lication can be configured in a fast fashion Clicking CONFIGURATION top menu button a BASIC SETTINGS page will be displayed All the application options are then available clicking the ADVANCED SETTINGS left menu button 3 4 4 BASIC SETTINGS The BASIC SETTINGS page is accessible clicking the CONFIGURATION button in the top menu it shows the most important options to be set up for a quick configuration Illustration 6 ICCLIENT Application basic settings Web Page Home CONFIGURATION STATUS DEFAULTS UPDATE REBOOT Intercom Client Station Basic Settings BASIC SETTINGS Bere CESSES BARP Station ID E Apply Cancel Duplex Mode Hat 9 Full Use Al Phone 9 No O Yes e BARP Station ID The system ID of this client station The ID is used to identify the unit at the master station Default setting is 1 Duplex Mode Choose the desired mode of operation If Half is selected the communication is controlled from the ICMASTER Default setting is Full Use Al_Phone This setting is for Annuncicom 200 hardware only which provides support for Al PHONE two wire interface Set to Yes if Al Phone is used as a door station In this case Half operating mode is recommended Default setting is No 3 4 2 ADVANCED SETTINGS The ADVANCED SETTINGS page is accessible clicking the Advanced Settings button in the left side menu EX Running ICCLIENT Illustration 7 ICCLIENT Application advanced set
42. lt message can be replaced in the ICgraph configuration folder Note the audio must be recorded in 16 bit mono WAV format and must have the same audio frequency than ICgraph and the devices have Start record Stop record this button allows to record running communication on ICgraph Recorded files will be displayed in Record window Recorded pagings to multiple points can be used to send later as pre recorded files to selected devices Note this function requires the installation of the MP3 libraries for more info see ICgraph manual EI Running ICgraph Settings this button opens on Windows PCs the Internet Explorer if a white point button was selected before then the Internet Explorer opens with the home page of the selected device 4 89 4 Intercom functionality with Icgraph In the Full duplex and in the Half duplex configurations everything is the same except the Intercom functionality To use the Intercom functionality the device must ring before to request the two way communication When ICgraph receives a Ring request from a device the according point button will change his color and blink magenta At this state select the point and click the Intercom button to get a two way communication In the Full duplex mode ICgraph configuration both sites can communicate with each other To finish the communication press the Clear All button In the Half duplex mode ICgraph configuration the Intercom button will after act
43. me can be omitted but the password has to be supplied in order to see the web configuration Old Password New Password These fields are visible as long as a password is set To allow free access clearing the password enter the old password and leave the field New Password empty Enter the old password in the password field above the Apply button as well and then hit the Apply button After the restart you will not be asked for user name and password anymore To change the password enter the old password and enter the new password in the field New Password Enter the old password in the password field above the Apply button as well and then hit the Apply button After the restart you will be asked for user name and password The user name can be omitted but the new password has to be supplied in order to see the web configuration EXJ Running ICMASTER 3 Running ICCLIENT 3 4 About ICCLIENT The ICCLIENT application has to be run on all client endpoints from the ICPAGING system The ICCLIENT can play BGM and paging messages initiate a call session to two preconfigured ICMASTER stations and send periodically its current status Being the slave component from the master slave architecture the ICCLIENT does not have the possibility to control other devices from the ICPAGING system 3 2 Available keys The ICCLIENT application uses the Input O key 1 and Input 1 key 2 that are available on the connector of the s
44. nload page Unzip the file Connect the ICMASTER station to the LAN and power it on Note down the IP address announced by the Sonic IP and point the browser to that address The application page of the PS16 will be displayed Click on the Update tab of the current installed firmware then click on the Please click here to start the update to go to the update page You will see the update page Click on Browse then navigate to the update rescue compound bin in the directory where you have unzipped the abcl_icpaging_vOxxxxxx zip file Select it then click on the Upload button to continue Update Barix Boctioader v99 12 Sep 29 2008 Resource Browse Upload Reboot Advanced Update Illustration 12 Device upload web page Reboot the device when the update is finished and open the web UI at the announced IP address Once the device reboot click on DEFAULTS top menu button and apply defaults The device will reboot again with default settings Note default ICPAGING running application is ICMASTER when compound bin is loaded and defaults settings are applied The package supplied 2 additional binaries update rescue compound master bin and update rescue compound client bin they respectively contain ICMASTER or ICCLIENT as the default running application 5 3 2 General settings Now it is time to configure our master station Once PS16 is rebooted open the Settings page and eventually
45. o the selected targets Make sure there are no clients selected by pressing the Cancel Sel key key 7 Keep pressed the custom message key key 6 lcd display will show a warning Nothing Selected then press key 5 and release it to start recording key 6 can be released from now Recording custom message will be displayed on the PS16 LCD Press again key 5 a second time to stop recording and save the message to the USB stick 5 8 2 Rejecting a call Press the call button on the Door or cash desk station Wait for the ICMASTER to display the message with the caller ID and play the ring tone then press key 3 to reject the call The client should play the busy tone 5 8 3 Answer a call Press again the call button on the client When the call indication is received on the master press key 1 and keep it pressed for a while As it is a PTT key the ICCLIENT is switched to listen mode when pressed and to talk mode when released Release the key to listen to the client and push it again to talk Press key 2 to toggle the relay on the client or key 3 to hang up the call 5 8 4 Paging Select the desired clients to be paged by pressing the corresponding target group buttons then press and hold the page key key 2 to send the message Release it when finished 5 8 5 Paging the custom message With a group selection active press the custom message key once The prerecorded message will be sent to the selected Ids and once th
46. on states meme nennen nnns 31 Illustration 11 Example intercom and paging system sssssssss eme emere 32 Illustration 12 Device upload web page sssssssseee eem nm emnnennn enn nne rrr nne n enne nnn nnne 33 Illustration 13 Group buttons address bitmap summary sese mener 34 Illustration 14 MP3 RTP Streamer main window unconfigureg sse mn 37 Illustration 15 MP3 RTP Streamer configuration dialog ssse Hee 37 Illustration 16 Address bitmap encoding sesseee emm emere nnne 41 Barix AG Seefeldstrasse 303 8008 Z rich SWITZERLAND T 4143 433 22 11 F 441 44 274 28 49 www barix com sales barix com support barix com Legal Information
47. or station As has been done for the master station once Annuncicom 200 is rebooted open CONFIGURATION and then Advanced Settings page and setup the desired options int the Network Settings section 5 4 3 Door station settings BARP Control section BARP Station ID Check the client ID to be 1 Audio section Duplex Mode Choose Half Audio section Use Al Phone Set to Yes Background Music section BGM First Broadcast Port Playing music on Al Phone is not possible because of the two line interface that it is using so set it to O no BGM Click the Apply button to save the settings and reboot the device 5 5 Configuring the cash desk station 5 5 1 Initial setup Do the initial setup as described in the ICMASTER General settings section After uploading the SW if the default running application is ICMASTER click REBOOT menu button and under the Reboot as drop down list select Intercom Client and click Reboot 5 5 2 General settings Now it is time to configure our door station As has been done for the master station once Annuncicom 100 is rebooted open CONFIGURATION and then Advanced Settings page and setup the desired options int the Network Settings section EZ implementing example paging system 5 5 3 Cash desk settings BARP Control section BARP Station ID Set the client ID 2 Click the Apply button to save the settings and reboot the device 5 6 Configuring
48. paging endpoint functionality In addition it has 2 lines LCD display and an IR port for remote control 1 Exstreamer 200 205 used as client Provides stereo BGM and paging endpoint functionality In addition it has 2x25 W amplified speaker output and an IR port for remote control Annuncicom PS1 this device can be used as a client or as a two buttons master allowing to answer incoming intercom call requests and to page a predefined group of targets Group key 1 Address Map from the web configuration page Annuncicom 60 used as a client NOTE other Barix devices not in this list may or may not work correctly with ICPAGING application NOTE when Annuncicom PS1 is used as a master all features using the USB stick are disabled i e customized station ringtones unattended mode recording unattended and custom messages 1 4 Additional documents Technical specifications for the supported devices can be found in the corresponding product sheet which can be downloaded from our site www barix com The ICPAGING System has been developed in BCL and is distributed with its source code enabling users to further customize it if they wish to For detailed technical information about the programming language please download the Barix Control Language BCL Programmers Manual from our website 1 5 ICPAGING ABCL Firmware Barix provides the ICPAGING solution as a prebuilt ABCL package containing the ICMASTER and ICCLIENT appl
49. set up the network settings Network setup is not mandatory if a DHCP server router exists in the network anyway for example a fixed IP address instead of default assigned DHCP address can make the device access easier in future reconfiguration operations Implementing example paging system ICMASTER settings Now it is time to configure the ICMASTER specific settings Click on the Advanced Settings tab and set the following items Basic Settings or Audio section Duplex Mode Choose Half Paging section Group 1 Address Map Click on the View Modify button to open the address map configuration dialog click Clear All then select id 1 only and click apply After device reboot click Close Paging section Group 2 Address Map Click on the View Modify button to open the address map configuration dialog click Clear All then select id 2 only and click apply After device reboot click Close Paging section Group 3 Address Map Click on the View Modify button to open the address map configuration dialog click Clear All then select id 3 only and click apply After device reboot click Close Group 4 Address Map Click on the View Modify button to open the address map configuration dialog We will dedicate this group to select all then we need to check clients ID 1 2 and 3 So click Clear All select 1 2 and 3 then click Apply at the bottom of the Group configurat
50. ssssseee 69 8 120 NetWork REG S tiere te uoi es eroe ec teo ies ete tees test eb ses scein 70 Legal Information ee eee eee ee eene eee eee e e eee ee eee ee eeeo 71 1 Introduction 1 1 About ICPAGING ICPAGING is a fully functional solution for building intercom and paging systems over IP based networks With ICPAGING BARIX devices can be easily configured and become part of the paging system in few minutes Being designed with a master client architecture the ICPAGING application can be configured to run either as a master called ICMASTER or as client called ICCLIENT The communication between the master and the client components of the paging system is implemented using the Barix IP protocol BARP The ICMASTER station can control the ICCLIENT s mode of operation send broadcast paging messages to any or all of them and activate their relays to drive different peripherals Multiple masters can coexist and be configured within a system Also the in the package contained ICgraph software Java based PC software can be used as ICMASTER system station The ICCLIENT stations are typically used as door intercom stations or paging stations with background music playback They can also be configured to initiate an intercom connection with up to two master stations 1 2 Features System master slave architecture BARP compatible integrates seamlessly with other BARP applications
51. st address is used Port is ignored if the IP is set to 0 0 0 0 Default is 0 0 0 0 12345 use broadcast 2 5 2 6 I O Control Relay 1 Control Configures the relay behavior The relay can be either off always off on while an incoming call is pending relay while ringing or on while a call is in process relay while talking EI Running ICMASTER Default is always off LED Status Configures the device front panel led behavior for the devices that have a led panel Default is Input State 2 5 2 7 Security Reset Function Enable or disable the Reset function on the Reset button and on the WEB UI In order to restart the device press the Reset button once Default enabled Factory Defaults Enable or disable the Factory Defaults function on the Reset button In order to revert all settings to factory defaults keep the Reset button pressed until the red LED starts blinking approx 10 seconds Default enabled Update Function Enable or disable the WEB Update function of the device If the Update function is disabled the only way to update the firmware is to use the serial rescue Default enabled Set Password This is visible as long as no password is set Enter a password up to 25 characters and hit the Apply button After the restart you should close the browser window and open a new browser window You will be asked to supply user name and password The user na
52. t priority 255 the lowest is reserved for BGM Default setting is 127 BARP Broadcast Address By default the ICCLIENT uses a broadcast IP to listen send on the BARP ports Modify the BARP IP address to use multicast if communication across different networks is desired or if your LAN policy is not allowing broadcast Default setting is 0 0 0 0 broadcast BARP Audio Port Enter the BARP port number to which the master will send audio for paging and established calls In the multicast port and address are configured this port will be used only for incoming calls Paging will be done using the multicast group Default is 5555 BARP Control Port Enter the BARP port number to which the master will send control messages Default is 5556 BARP Status Port Enter the destination port number where the master will listen for BARP status messages Default is 5557 2 5 2 3 Audio Audio Format Running ICMASTER Choose between different encoding types and sampling frequencies u law or A law at 8 or 24 kHz Default setting is u law 8 kHz IMPORTANT If you change the encoding don t forget to provide record correct unattended custom audio message files Also make sure to use the same encoding on ALL devices of the ICPAGING system Input Source Choose the desired input source Default setting is Mic Duplex Mode Choose the desired mode of operation Default setting is Full
53. ted as 0 9 and as A for 10 to F for 15 The following table can serve as a conversion chart Bin DEC Hex Table Decimal Binary Hexadecimal 0 0000 0 1 0001 1 2 0010 2 3 0011 3 4 0100 4 5 0101 5 6 0110 6 ZV Additional information Decimal Binary Hexadecimal 7 0111 7 8 1000 8 9 1001 9 10 1010 A 11 1011 B 12 1100 C 13 1101 D 14 1110 E 15 1111 F To convert a binary value in a hexadecimal representation the upper and lower four bits are treated separately resulting in a two digit hexadecimal number 7 Troubleshooting Below just a brief table to help solving the main known issues 1SSUE Description Possible cause and remedy action Device boot but web UI home page frames shows ERROR 400 ICPAGING has been uploaded over an existing different ABCL fw based application Click DEFAULTS on the top menu and apply defaults Device not visible in the LAN network An IP assignment server is missing in the LAN or there could be a LAN cable issue Check device LAN cable connections eventually set firmware defaults through keeping pressed the device front panel reset button for more than 10 seconds then listen to SoniclP If the above don t solve the issue try the serial rescue process see par Fehler Referenz nicht gefunden Audio is missing Volume level is set to O mic or speakers wiring
54. tings Web Page Home ConFIGuRaTIoN STATUS DEFAULT UPDATE resoor Intercom Client Station x Advanced Settings BARP Station ID IH J BARP Broadcast Address 0 0 0 0 BARP Audio Port ss Outgoing Call BARP Control Port 5556 Background Music BARP Status Port 5557 E ificati Oo VO Control Notification Port No Yes Apply Cancel 3 4 2 1 Network This section is the same as in ICMASTER See ICMASTER 2 5 2 1 Network section 3 4 2 2 BARP Control BARP Station ID The system ID of this client station The ID is used to identify the unit at the master station Default setting is 1 BARP Broadcast Address By default the ICCLIENT uses broadcast to listen send on the BARP ports Modify the BARP IP address to use multicast if communication across different networks is desired or if your LAN policy is not allowing broadcast Default setting is 0 0 0 0 BARP Audio Port Enter the BARP port number where the ICCLIENT will listen for incoming audio Default setting is 5555 BARP Control Port Enter the BARP port number where the ICCLIENT will listen for BARP control messages Default setting is 5556 BARP Status Port Enter the destination port number to which the ICCLIENT will broadcast BARP status messages Default setting is 5557 EE Running ICCLIENT Notification Port Enable here the usage of the notification port whi
55. ts that try to call a master that is in unattended mode will have the unattended message played to them and the call will be terminated once the message has been played Pressing and holding this key for 4 seconds will enter the master in call reject mode When the master is in this mode and a client calls in instead of opening a call session and sending the unattended message it will send a special message to the client informing that it is not available In this case the client should call the next master in its list NOTE if the ICMASTER does not cancel answer the second call the ICCLIENT will continue ringing and hang up automatically after a certain amount of time configurable via the ICCLIENT web Ul NOTE when the unattended mode is disabled from the web UI pressing this key puts the master immediately in call reject mode Key 5 press once start recording unattended message A second press stops the recording and saves the message for use An initial unattended message must be recorded when the System is first being set up otherwise calls will be hung up without explanation EE Running ICMASTER Key 6 record page custom message In case of any selected targets groups broadcasts the message otherwise it has no effect To record the custom message press and hold this key then press key 5 once Record your message then press again key 5 to finish Key 7 clear current target group selection If the dynamic group
56. ultiple masters may be needed in the paging system For example a door station may need to ring to the reception at the entrance during normal working hours and to the security room at night For this purpose ICPAGING supports several multimaster scenarios 6 3 1 Call Failover scenario In this case maximum 4 masters can be called by the client If one of the first two masters in the client IP ID list are called and it is in call reject mode then the client starts calling the other three masters in a chain However if the first master does not reply or any other master called in the chain then the client will timeout and may not connect to any master To prevent this happen the Call next Master on the client must be enabled 6 3 2 Call all masters scenario For that mode the masters must be addressed by IP This is done by setting the ICCLIENT Call Masters by and the ICMASTER Call Master by configuration options to IP Address Then it is enough to set one of the first two master IP addresses in the ICCLIENT list to IP address 0 0 0 0 In this case when the call button associated with that IP address is pressed then the call request is broadcasted to all masters and one of them may pickup The masters track the current state of the calling client status message and if it changes to something other that 3 connecting then they stop ringing The masters also stop ringing if more than 5 seconds have elapsed after the last call r
57. upported BARIX devices The mapping of the keys is the following Key 1 Call ICMASTER station 1 The id or IP of the ICMASTER station is configured via the ICCLIENT web configuration page Key 2 Call ICMASTER station 2 The id or IP of the ICMASTER station is configured via the ICCLIENT web configuration page If the ICCLIENT is configured to operate with the AIPHONE door panels then the hardware inputs are ignored and the key 1 press is emulated by the firmware The IP of the ICMASTER station 1 is only used in this case Note The ICCLIENT can use the HAI Volume Source Control unit together with the BARIX IR Remote Control However if the ICCLIENT is run on BARIX device with its own LCD display ex BARIX Exstreamer 110 then the VSC LCD cannot be used and stays blank 3 3 ICCLIENT Web home page The device home page is dynamically auto refreshed every second and shows some useful runtime application details Illustration 5 ICCLIENT home page L HOME k CONFIGURATION e STATUS l DEFAULTS n UPDATE l 77 Intercom Client Station APPLICATION STATUS BARP Station ID 1 Current Status IDLE AUDIO LEVELS Input Level 127 dB Output Level 127 dB Under the APPLICATION STATUS section is visible the station ID and the current application status EIE Running ICCLIENT Under the AUDIO LEVELS section input and output audio levels are displayed in dB 3 4 ICCLIENT Web configuration page As in ICMASTER the ICCLIENT app

Download Pdf Manuals

image

Related Search

Related Contents

Bitdefender Antivirus Plus 2015  Product Manual  Axis Communications 232d+ User's Manual  Téléphone Senior VOIIS V1  Cordless Circular Saw Model C 18DBL Handling instructions  Builders Edge 050010212000 Installation Guide  Canon VB-S900F Specifications  Avaya an Expansion Module in a BayStack ARN Router (114202 Rev. A) User's Manual  essentiels - Conseil général  Model 66 & 77 Peristaltic Pump Series User`s Manual  

Copyright © All rights reserved.
Failed to retrieve file