Hobbes LANID
Contents
1. port wall plate or patch panel that you wish to test e Push the TEST button and read the results Copyright Hobbes GmbH Hobbes INNOVATION 4 Hobbes LANID Network On line Status Tester e The Hobbes LANID will determine the status of the port and display the capabilities of the device connected left hand side as well as the link status right hand side 2 NIC Network Interface Card Testing e Plug the provided patch cable into the NIC port on the right hand side on the Hobbes LANID e Push the TEST button and read the results e The Hobbes LANID will display the capabilities of the NIC connected left hand side as well as the link status right hand side e If you are not sure whether a HUB or NIC is connected on the other end you can push the TEST button to see if the green LINK LED lights up e This will tell you that the cable is connected to an NIC or a Hub uplink port Features e IEEE 802 3 compliant Fast Ethernet PHY negotiation e Power down mode significantly reduces power consumption e LED indicators test and monitor line connection status and determine features of the device being tested e RJ45 connector allows quick and easy connections to most network devices e Small hand help pen style casing allows for convenient application and portability Specifications Copyright Hobbes GmbH INNOVATION 5 Hobbes LANID Network On line Status Tester2. 100F O TX FULL 100HO 3 HALF red m 4 100 10 F ane 10 red 10H3 FE ERROR POWER 5 The tested device is a 100 BASe T4 device capable of auto negotiation red AUTO FE 100F O 100 H 10 F 10H a POWER NOTE Hobbes LANID does not Link with LOOBASE T4 but it can advertise in the Auto Negotiation LOOBASE T4 operation 6 The tested device is a 10 100 BASE TX capable of auto negotiation but is configured at 1OMbps Copyright Hobbes GmbH INNOVATION green AUTO J JE LINK 100 F O O TX i100 H FULL green HALF i 4 100 10 F ZE 10 red 10HZE gt ERROR POWER 8 Hobbes LANID Network On line Status Tester NOTE If you configure a NIC as 10Mbps full duplex mode the device capability display will be different from the above diagram depending on the NIC device driver This means your card is capable of 10 or 100 Mbps but you are running the card at only 10 Mbps You should then reconfigure your card to the maximize speed 7 The tested device is a 10 BASE T device but the battery power is too low to display reliable results At this time you must replace the battery with a new one AUTO 100 F O TX 100 H HALF red 100 10F FE 10 red 10HZE ERROR 3 Flashing POWER Article Nr 256655 Copyright Hobbes GmbH Made in Taiwan
3. INNOVATION 1 Hobbes LANID Network On line Status Tester User Manual Specifications Introduction 2 Hobbes LANID Contents 2 Product profile 3 Application 3 Features 4 4 5 LAN ID Signal description Hobbes GmbH Europa Distribution Willhoop 3 22453 Hamburg Germany July 2007 D http www hobbes europe com Changes and mistakes may occur Copyright Hobbes GmbH Hobbes INNOVATION 2 Hobbes LANID Network On line Status Tester Introduction Congratulations on your purchase of the Hobbes LANID Network Device identifier The Hobbes LANID is the quintessential diagnostic tool for network installers and troubleshooters working with small LANs Using the Hobbes LANID network administrators can quickly confirm features of LAN devices and diagnose problems during LAN installation With a push of a button the LAN will determine whether the device you are testing whether it supports the following topologies and capabilities e Auto negotiation e 1O00BASE Tx full duplex e 1OOBASE Tx half duplex e 1OBASE T full duplex e 1OBASE T half duplex e 100BASE T4 Moreover the Hobbes LANID can also act as a network device negotiating with other LAN devices to determine faults The auto negotiation function provides automatic speed matching for multi speed devices allowing devices to configure to the best possible mode of operation over a link When linked up with another LAN device the Hobbe
4. Model number 296699 Connector type RJ 45 Recommended operation temperature 0 70 C Power supply DCS 2 AAA battery Power consumption 350 mW typical 100 2 W in Power Down Mode Display LED indicator Enclosure Durable plastic housing Dimensions 215x34s34mm LANI D Signal Description O LED is off 34 LED is on 1 The tested device is a 10 100 BASE TX half full duplex device capable of auto negotiation and link at a speed of 100Mbps in full duplex mode green AUTOSE JE LINK 100FZ OTX OHt g FULL green e 100 green 1oF Re He 10016 10HZE ERROR J POWER 2 The tested device is a 10 BASE T NIC without auto negotiation and link at a speed of 10Mbps in half duplex mode Copyright Hobbes GmbH INNOVATION 6 Hobbes LANID Network On line Status Tester AUTO 100 F 2 TX 100 H O FULL HALF red oe Ap 10F 3g 100 5 10 red 10HZE ERROR Jk POWER 3 The tested device is a 100 BASE TX full duplex device capable linked at 100Mbps in full duplex mode It is also transmitting an auto negotiation packet AUTO O 3 LINK iOFZE ZETX e FULL green 100 H 3 HE HALF 10F 74 190 green 10 H O ERROR POWER 4 The tested device is a 10 BASE T half duplex device linked at 10Mbpsin half duplex mode and is communicating bad packets Copyright Hobbes GmbH INNOVATION 7 Hobbes LANID Network On line Status Tester AUTOO 3 LINK
5. s LANID will provide the following information about that device e Whether the link is up or not e Whether the device is transmitting a packet or not e Whether the device is working in full duplex mode or half duplex mode e Whether the device is operating in LOOBASE Tx 10BASE T or LOOBASE T4 mode e Whether a data transmission error has occurred The compact pen style design provides the user with optimum convenience and portability Hobbes LANID Contents 1 Hobbes LANID 1 User manual Copyright Hobbes GmbH INNOVATION 3 Hobbes LANID Network On line Status Tester 1 Soft vinyl carrying pouch 15 cm Twisted pairs RJ45 cable 1 RJ45 to RJ45 coupler Product profile os 1 ai 1 PLUG TO HUES JACK E 2 AUTO NEGOTIATION LED 10 100 BASE T GREEN LED C 7 100 BASE T4 RED LED a 4 3 3 100Mbps WITH FULL DUPLEX LED 3 4 100Mbps WITH HALF DUPLEX LED 9 8 10Mbps WITH FULL DUPLEX LED br 41 6 10Mbps WITH HALF DUPLEX LED oF 7 LINK LED Ha b a TX LED ay 3 FULL DUPLEX OR HALF DUPLEX LED paG id 100 Mbps OR 10Mbps LED 6 J ERROR STATUS LED 63 12 FOR NIC Network Interface Card JACK FA 13 POWER LED oe 4 POWER ON OFF SWITCH 8 TEST KEY 16 G LEFT SIDE FOR DEVICE CAPABILITY INDICATOR 7 RIGHT SIDE FOR LINK STATUS INDICATOR Application 1 HUB Testing e Turn the power switch on and plug the Hobbes LANID marked Hub Into a hub
Download Pdf Manuals
Related Search