Install Guide (NX58J7750SS_install
Contents
1. Di Di Gliding rack 1 Anti tip bracket kit e Make sure you have received all of the supplied parts shown above Work grate 1 e If your range was damaged during shipping or you do not have all of the supplied parts contact your local retailer o n Vv a 3 o 0 u u English 23 Install NX58J7750SS_DG68 00624A 00_EN indd 23 amp 2015 02 04 RR 11 52 35 Tools and materials Parts needed J J Gas line shut off valve SO Flexible metal appliance connector in ID x 5 ft i 135 degree elbow optional Tools needed CE Lag bolt or in OD sleeve anchor EE Flare union adapter in or in NPT x in ID Flare union adapter in NPT x in ID Flat blade screwdriver Phillips screwdriver Open end or adjustable wrench Pipe wrench 2 N i Utility knife 24 English Install NX58J7750SS_DG68 00624A 00_EN indd 24 Soapy water solution et ZZZ o ES eee D u o C a 3 Nut driver Pencil and ruler Level Pipe joint compound 5 ra 2015 02 04 RR 11 52 38 Installation instructions Installing your gas range IMPORTANT Please read the following instructions as well as the Important Safety Instructions section at the front of this manual completely and carefully BEFORE installing and or operating the gas range Improper installation adjustment se2. required between the Screw must enter wood or concrete range bottom and the kitchen floor To check if the bracket is installed and engaged properly remove storage drawer and look underneath the range to see that the leveling leg is engaged in the bracket Carefully tip the range forward The bracket should stop the range within 4 inches 10 2 cm of tipping If it does not the bracket must be reinstalled n et o D le J n et a e ie u 28 English Install NX58J7750SS_DG68 00624A 00_EN indd 28 amp If the range is pulled from the wall for any reason always repeat this procedure to verify the range is properly secured by the anti tip bracket Never completely remove the leveling legs or the range will not be secured to the anti tip device properly 2015 02 04 RR 11 52 40 Step 5 Plug in and place WARNING BEFORE OPERATING OR TESTING follow the grounding requirements on pages 20 22 in this manual Improper connection of the grounding plug can result in a risk of electric shock Gas Range Plug Step 6 Level the range Leveling leg NOTE Adjusting the two front legs is usually sufficient but all four legs adjust if necessary Install NX58J7750SS_DG68 00624A 00_EN indd 29 All gas ranges come with a power cord The power cord is connected to the rear of the range Please review Electrical requirements on
3. Special gas requirements gas models sold in massachusetts COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS WARNING e Range must be installed by a qualified plumber or gas fitter by the State of Gas leaks may occur in your system Massachusetts creating a dangerous situation e A T handle manual gas valve MUST be Gas leaks may not be detected by smell installed in the gas supply line to your alone range Gas suppliers recommend you purchase If a flexible gas connector is used to install and install a UL approved gas detector your range multiple flexible gas lines must Gas detector should be installed in not be connected in series accordance with the manufacturers instructions Electrical requirements WARNING A wiring and grounding must be done in accordance with local codes or in the To reduce the risk of fire electric shock or absence of local codes with the National personal injury Electrical Code ANSI NFPA No 70 Latest All ranges Revision for the U S or the Canadian Electrical Code CSA C22 1 Latest e Do not use an extension cord or adapter plua witwthierange Revisions and local codes and ordinances e Wiring diagram is located on the back of AWS range must RE propery graunte the range Inside of the cover back wire e Check with a qualified electrician if you are in doubt as to whether your range is properly grounded un e DI D Ep x D a i
4. the C chanel of the valve until it hits the simmer set screw Make sure the screwdriver flathead is seated into the set screw groove 3 Rotate valve set screw clockwise to decrease LO setting flame output or rotate set screw counter clockwise increase LO setting flame output to 2015 02 04 RR 11 52 45 Memo Install NX58J7750SS_DG68 00624A 00_EN indd 37 amp 2015 02 04 RR 11 52 45 Memo Install NX58J7750SS_DG68 00624A 00_EN indd 38 amp 2015 02 04 RR 11 52 45 Memo Install NX58J7750SS_DG68 00624A 00_EN indd 39 amp 2015 02 04 RR 11 52 46 m a Scan the QR code or visit www samsung com spsn to view our helpful m How to Videos and Live Shows QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT CANADA 1 800 SAMSUNG 726 7864 yw samsung zomica fismppor French Consumer Ziectronics 1 800 SAMSUNG 726 7864 www samsung com us support ui 1 800 SAMSUNG 726 7864 www samsung com us support Install NX58J7750SS_DG68 00624A 00_EN indd 40 DG68 00624A 00 2015 02 04 SD 11 52 25
5. accordance with the local codes and ordinances If you are unsure whether your electrical outlet is properly grounded have it checked by a licensed electrician 8 English Install NX58J7750SS_DG68 00624A 00_EN indd 8 amp 2015 02 04 RR 11 52 28 e The range is supplied with a 3 pronged grounded plug This cord must be plugged into a mating grounded 3 prong outlet that meets all local codes and ordinances If codes permit the use of a separate ground wire we recommend that a qualified electrician determine the proper path for this ground wire e Electrical service to the range must conform to local codes Barring local codes it should meet the latest ANSI NFPA No 70 Latest Revision for the U S or the Canadian Electrical Code CSA C22 1 Latest Revisions e It is the personal responsibility of the range owner to provide the correct electrical service for this range Installation safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions II e Have your range installed and properly gt Sy grounded by a qualified installer 3 GT e 5 e gt u w h Lee lt le 5 3 w e in accordance with the installation E Z DF instructions Any adjustment and service V should be performed only by qualified gas range installers or service technicians Do not attempt to service modify or replace your rang
6. but not over other surface burners e Stand away from the range while frying e Always heat frying oils slowly and watch as they heat If you are frying foods at high heat carefully watch during the cooking process If a combination of fats or oils is to be used during frying mix them together before heating Use a deep fryer thermometer whenever possible This prevents overheating the fryer beyond the smoking point e Use a minimum amount of oil when shallow pan frying or deep frying Avoid cooking unthawed food or food with excessive amounts of ice 3 Ke 3 mi o u 0 D lt n Vv st e Before moving cookware full of fats or oils make sure it has completely cooled e To prevent delayed eruptive boiling always allow heated liquids to stand at least 20 seconds after you have turned off the burner so that the temperature in the liquid can Stabilize In the event of scalding follow these first aid instructions 1 Immerse the scaled area in cool or lukewarm water for at least 10 minutes 2 Do not apply any creams oils or lotions 3 Cover with a clean dry cloth 12 English Install NX58J7750SS_DG68 00624A 00_EN indd 12 amp 2015 02 04 RR 11 52 28 Oven safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions e Do not use the oven for non cooking purposes such as drying clothes or
7. death personal injury or property damage Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS e DO NOT light a match candle or cigarette e DO NOT try to light any appliance e DO NOT touch any electrical switch e DO NOT use any phone in your building e Clear the room building or area of all occupants e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or gas supplier Never use an old connector when installing a new range If the hard piping method is used you must carefully align the pipe the range cannot be moved after the connection is made To prevent gas leaks apply pipe joint compound or wrap pipe thread tape with Teflon on all male external pipe threads 1 Install a manual gas line shut off valve in the gas line in an easily accessed location outside of the range Make sure everyone operating the range knows where and how to shut off the gas supply to the range 26 English Install NX58J7750SS_DG68 00624A 00_EN indd 26 2 Install male 0 5 in 1 3 mm flare union adapter to the 0 5 in 1 3 mm NPT internal thread at the regulator inlet Use a backup wrench on the regulator fitting to avoid dam
8. pages 20 22 e All U S and Canadian models are produced with a 3 wire 120 volt 60 Hertz electrical system The entire system including the power cord is preinstalled and prewired 1 Plug in the power cord Make sure the outlet meets local or national electrical codes as referenced on pages 20 22 2 Slide the range into place 3 Check the gas supply line to make sure it did not get damaged and it stayed connected during positioning 4 Check to make sure the back leg of the range has slid into the anti tip bracket Carefully tip the range forward to ensure that the anti tip bracket engages the back brace and prevents tip over 1 Make sure the range is positioned where you want it 2 Using a wrench level the range by turning the front leveling legs in or out as necessary Counterclockwise shortens the leg and lowers the range Clockwise lengthens the leg and raises the range NOTE Adjust the leveling legs only as far as necessary to level the range Extending the leveling legs more than necessary or removing legs can cause the range to be unstable English 29 amp 2015 02 04 RR 11 52 40 gt n et a D Sr J n et a ei gt u Installation instructions 3 If range is next to or between cabinets make sure the cooktop without the surface burner grates is level with the countertops 4 Position an oven rack in the center ra
9. 2 pan and then place the pan on the turn it over and start cooking the other desired rack Side gt 2 Press the Broil pad once for high 5 When on both sides is complete press the a mi a temperature broiling or twice for low OFF CLEAR pad Si 3 Press the START SET pad to start cooking n English 33 Install NX58J7750SS_DG68 00624A 00_EN indd 33 amp 2015 02 04 SD 11 52 43 Installation instructions Checking the flame quality All combustion flames need to be visually checked to determine their flame quality 1 Soft blue flames Normal for natural gas operation 1 2 Yellow tips on outer cones Normal for LP gas operation 3 Yellow flames Abnormal for any gas operation call for service NOTE If burner flame looks like 3 the range Should not be used until it is serviced Call for service Normal burner flames shall look AS like 1 or 2 depending on the gas type you use IO Step 9 Final installation checklist You have just completed installing your range Make sure all controls are in the off position and the flow of ventilation air to the range is unobstructed The following is a checklist to confirm your range is safely installed and ready for operation Gas line has been properly connected to i the range The gas has been turned on All connections have been checked for leaks i z Range is plugged into the properly grounded electrical receptacle Approved ant
10. 3 D et u e This range is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly Do not modify the plug provided with polarized your range if it doesn t fit the outlet have a proper outlet installed by a qualified electrician 20 English Install NX58J7750SS_DG68 00624A 00_EN indd 20 amp 2015 02 04 RR 11 52 32 Gas models e All gas models are equipped with a power cord with an equipment grounding conductor and a grounding plug e A 120 Volt 60 Hz AC approved electrical service with 20 amp circuit breaker or time delay fuse is required for all U S and Canadian models e Check for in 1 9 cm UL listed strain relief where the power cord comes out of the range cabinet Grounding jd N Ensure proper ground and firm connection _ before use A e All ranges must be grounded for persona safety e All gas models have a power cord with an equipment grounding conductor and a grounding plug e The plug must be firmly plugged into a three prong outlet that is properly installed and grounded in accordance with all local codes and ordinances In the event of a malfunction or breakdown grounding will decrease the risk of electrical shock by providing a path for the electric current Do not use a damaged power plug or loose wall outlet Install NX58J7750SS_DG68 00624A 00_EN indd 21 e Do not reuse a power supp
11. 5 02 04 RR 11 52 26 3 Ke 3 mi Vv J n o Sh D lt SR 3 Vv Important safety information General safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions 7 e Do not touch any part of the range a including but not limited to oven burners A surface burners or interior surfaces during H or immediately after cooking e Know the location of the gas shut off valve and how to shut it off e Make sure the anti tip device is properly installed on the range See the installation instructions for more information Do not let children near in or on the range Do not let children play with the range or any part s of the range Do not leave children unattended in an area where the range is in use For children s safety we recommend utilizing the control door lockout feature 3 Ke e 3 w J u w h e lt le 3 w Zi e Remove all packaging materials from the range before operating to prevent ignition of these materials Keep all packaging materials out of children s reach Properly dispose the packaging materials after the range is unpacked Do not store any object of interest to children on the cooktop or backguard of the range Children climbing on the range to reach items could be killed or seriously injured e Do not opera
12. Flex Connector Manifold h Pressure Regulator Adapter Step 3 Convert to Ip gas optional All new gas ranges are shipped from the factory set Up to use natural gas Any Samsung gas range can be converted to use LP gas Refer to page 78 in the User Manual to contact a qualified service technician The conversion process should only be performed by a qualified LP gas installer Conversion instructions and LP orifices will be supplied with the LP conversion kit The conversion to LP requires all burner orifices to be changed 5 surface burners and 2 oven burners In addition the nozzle on the gas pressure regulator needs to be reversed All replaced orifices must be left with the consumer including the instructions and retrofit sizes and orifice indication Install NX58J7750SS_DG68 00624A 00_EN indd 27 NOTE If your area requires a rigid pipe hookup contact a qualified installer service agency or gas supplier NOTE The gas shut off valve should be installed in an accessible location in the gas piping external to the appliance for the purpose of turning on or shutting off the gas to the appliance BURNER ORIFICE SIZES AND OUTPUT RATINGS LP Gas Propane 10 in WCP Burner Orifice Size ia Location RIS mm RF 14 500 1 12 a LF 11 500 1 04 RR 4 000 0 62 8 LR 7 500 0 83 CTR 7 500 0 83 3 BAKE 15 000 1 15 BROIL 14 500 112 a BURNER O
13. Free Standing Gas Range installation manual NX58J7750SS WARNING If the information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death e DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance e WHAT TO DO IF YOU SMELL GAS DONOT try to light any appliance DO NOT touch any electrical switch DO NOT use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department e Installation and service must be performed by a qualified installer service agency or the gas supplier Anti tip device WARNING ALL RANGES CAN TIP RESULTING IN PERSONAL INJURY we TIPPING RANGES CAN CAUSE BURNS FROM SPILLS PERSONAL INJURY AND OR DEATH INSTALL AND CHECK THE ANTI TIP BRACKET FOLLOWING THE INSTRUCTIONS AND TEMPLATE SUPPLIED WITH THE BRACKET e TO prevent accidental tipping of the range attach an approved anti tip device to the floor See Installing the Anti Tip Device in the Installation Instructions Check for proper installation by carefully tipping the range forward The anti tip device should engage and prevent the range from tipping over e If the range is pulled out away from the wall for any reason make sure the anti tip devi
14. HT 220 Ib 100 kg ElEGIRICAR Refer to the rating label GAS NG NATURAL GAS 5 13 in WC GAS LP LIQUID PROPANE 10 13 in WC SURFACE BURNERS NG LF 15 000 BTU LR 9 500 BTU CTR 9 500 BTU RR 5 000 BTU RF 18 000 BTU SURFACE BURNERS LP LF 11 500 BTU LR 7 500 BTU CTR 7 500 BTU RR 4 000 BTU RF 14 500 BTU OVEN BURNERS NG Broil Upper 13 500 BTU Bake Lower 18 000 BTU OVEN BURNERS LP Broil Upper 14 500 BTU Bake Lower 15 000 BTU 16 English Install NX58J7750SS_DG68 00624A 00_EN indd 16 amp 2015 02 04 ERR 11 52 31 Installation requirements Location requirements Clearances and dimensions BEFORE YOU BEGIN to install this appliance CAUTION refer to the following information dimensions and clearances Do not This range has been designed to comply locate the range where it may be subject with the maximum allowable wood cabinet to strong drafts Provide adequate temperature of 194 F 90 C Make sure clearances between the range and adjacent the wall covering countertops and cabinets combustible surfaces These dimensions around the range can withstand the heat up must be met for safe use of the range to 194 F 90 C generated by the range If The location of the electrical outlet and not discoloration delamination or melting gas piping may be adjusted to meet the may occur following dimensions and clearances For installation in Canada a free standing ran
15. RIFICE SIZES AND OUTPUT RATINGS Natural Gas 5 in WCP Burner Orifice size location BIN elle mm RF 18 000 1 92 LF 15 000 1 78 RR 5 000 1 01 LR 9 500 1 40 CTR 9 500 1 38 BAKE 18 000 1 90 BROIL 13 500 1 64 English 27 2015 02 04 RR 11 52 39 Installation instructions Step 4 Install the anti tip device WARNING To reduce the risk of tipping the appliance must be secured by properly installing the anti tip device packed with the appliance e All ranges can tip resulting in personal injury e Tipping ranges can cause burns from spills personal injury and or death e To prevent accidental tipping install and check the anti tip bracket following the instructions and template supplied with the bracket An anti tip bracket and screws installation instructions and template are shipped with every range PN DG94 00870B The instructions include information necessary to complete the installation of the anti tip bracket Read and follow the instructions on the sheet and use the template for anti tip bracket installation If not properly installed the range could be tipped by you or a child standing sitting or leaning on an open oven door Anti Tip bracket approximately NOTE To install the Anti Tip bracket release the leveling leg em A minimum clearance 21 32 16 5 mm denm of 21 32 16 5 mm is
16. age When installing the range from the front remove the 90 elbow for easier installation 3 Install male 0 5 in 1 3 mm or 0 75 in 1 9 mm flare union adapter to the NPT internal thread of the manual shut off valve taking care to back up the shut off valve to keep it from turning 4 Connect flexible metal appliance connector to the adapter on the range Position range to permit connection at the shut off valve 5 When all connections have been made make sure all range controls are in the off position and turn on the main gas supply valve Use a liquid leak detector at all joints and connections to check for leaks in the system WARNING Do not use a flame to check for gas leaks to prevent death personal injury explosion and or fire hazard When using test pressures greater than 1 2 psig to pressure test the gas supply system of the residence disconnect the range and individual shut off valve from the gas supply piping When using test pressures of 1 2 psig or less to test the gas supply system simply isolate the range from the gas supply system by closing the individual shut off valve 2015 02 04 RR 11 52 39 Flexible connector hookup Installer Inform the consumer of the location of the gas shut off valve Gas Shut Off Valve P 0 5 in or 0 75 in Gas Pipe Tubing Line to Oven Burner CO fo 2 Adapter Control Valve me 2 Tubing Line a to Cooktop F Control 8 n 8
17. ce is reengaged after the range has been pushed back into place e Follow the installation instructions found in the Installation Manual Failure to follow these instructions can result in death serious personal injury and or property damage e DO NOT step sit lean on the door or drawer to prevent accidental tipping of the range 2 English Install NX58J7750SS_DG68 00624A 00_EN indd 2 amp 2015 02 04 RR 11 52 26 Before you begin 4 Important safety information 5 gas range components 15 Overview 15 Gas range specifications 16 Installation requirements 17 Location requirements 17 Gas requirements 19 Special gas requirements gas models sold in massachusetts 20 Electrical requirements 20 tools and materials 23 What s in the box 23 Installation instructions 25 Installing your gas range 25 Step 1 Unpack the range 25 Step 2 Connect the range to gas supply 25 Step 3 Convert to Ip gas optional 27 Step 4 Install the anti tip device 28 Step 5 Plug in and place 29 Step 6 Level the range 29 Step 7 Assemble the surface burners 30 Step 8 Check the ignition of surface burners and oven burners 32 Step 9 Final installation checklist 34 Adjusting the oven burner air adjustment shutters 35 Install NX58J7750SS_DG68 00624A 00_EN indd 3 amp English 3 2015 02 04 RR 11 52 26 S U2 UO Before you begin ABOUT THIS MANUAL READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY Impor
18. ck position 5 Check the level of the range with a carpenter level using the two positions shown at right 6 After the range becomes level slide the range away from the wall so that the anti tip bracket can be installed CAUTION Do not operate the surface burners without o ad C_D all burner parts in place 1 Position surface burner heads on top of the surface burner manifolds as shown at right The electrodes will fit into the slot in the bottom of the heads Make sure the surface burner heads are flat and parallel with the cooktop 2 Place the matching size caps on top of each surface burner head 5 n et DI D Sh n et a st gt n 30 English Install NX58J7750SS_DG68 00624A 00_EN indd 30 amp 2015 02 04 RR 11 52 41 Precise Simmer Burner RR NOTE The caps on Precise simmer burner RR and inside Dual Burner RF can be interchangeably used Flat surface Concave line 3 Place the left center and right surface burner grates on the cooktop The edges of the grates should match vp with the edges of the cooktop gt n et a D Sr e n et a ei gt u English 31 Install NX58J7750SS_DG68 00624A 00_EN indd 31 amp 2015 02 04 RR 11 52 42 Installation inst
19. cooking surface and e 30 in 76 2 cm minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet or If no 30 in 76 2 cm minimum clearance 24 in 61 cm minimum when the bottom of the wood or metal cabinet is protected by not less than 0 25 in 0 64 cm flame retardant millboard covered with not less than no 28 MSG sheet steel 0 015 in 0 038 cm stainless steel 0 024 in 0 061 cm aluminum or 0 020 in 0 051 cm copper the ventilation hood surface must never be 18 in 45 7 cm minimum between the less than 24 inches countertop and the adjacent cabinet bottom Recommended locations for gas piping and electrical outlets Recommended area for 120 V electrical outlet on rear wall u et feni D ct x OD Q 3 M gt et u 2inx2 in 5 1 cm x 5 1 cm 17 in x 2 in 43 2 cm x 5 1 cm Gas Floor Area 17 in x 2 in 43 2 cm x 5 1 cm Gas Floor Area Recommended area for through the wall and through the floor connection of gas pipe stub and shut off valve 18 English Install NX58J7750SS_DG68 00624A 00_EN indd 18 amp 2015 02 04 RR 11 52 32 Gas requirements Provide adequate gas supply This range is designed to operate at a pressure of 5 in 13 cm of water column on natural gas or 10 in 25 cm of water column on LP gas propane or butane Make sure you are supplying your range with the type of gas for which i
20. ding to the manufacturer s instructions Do not use a flame to check for gas leaks Use a brush to spread a soapy water mixture around the area you are checking If there is a gas leak you will see small bubbles in the soapy water mixture at the leak point Electrical and grounding safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions Plug into a grounded 3 prong outlet 3 Ke le ow J u w h D lt le 3 w Si e Do not remove the ground prong Do not use an adapter or an extension cord Do not use a damaged power plug power cord or loose power outlet Ne A e Do not modify the power plug power cord or power outlet in any way Do not put a fuse in a neutral or ground circuit e Use a dedicated 120 volt 60 Hz 20 amp AC fused electrical circuit for this range A time delay fuse or circuit breaker is recommended Do not plug more than one appliance into this circuit Do not connect the ground wire to plastic plumbing lines gas lines or hot water pipes e This range must be Earth grounded In the event of a malfunction or breakdown grounding will reduce the risk of electrical shock by providing a path for the electric current This range is equipped with a cord having a grounding plug The plug must be firmly plugged into an outlet that is properly installed and grounded in
21. e or any part of your range unless it is specifically recommended in this manual All other service should be referred to a qualified technician e Always use new flexible connectors when installing a gas appliance Do not use old flexible connectors e Make sure the anti tip device is properly installed on the range See the installation instructions for more information e Due to the size and weight of the range have two or more people move the range e Remove all tape and packaging materials e Remove all accessories from the cooktop oven and or lower drawer Grates and griddles are heavy Use caution when handling them e Make sure no parts came loose during shipping English 9 Install NX58J7750SS_DG68 00624A 00_EN indd 9 amp 2015 02 04 RR 11 52 28 Important safety information e Make sure your range is correctly installed and adjusted by a qualified service technician or installer for the type of gas natural or LP you will use For your range to utilize LP gas the installer must replace the 5 surface burner orifices and 2 oven orifices with the provided LP orifice set and reverse the GPR adapter These adjustments must be made by a qualified service technician in accordance with the manufacturer s instructions and all codes and requirements of the authority having jurisdiction The qualified agency performing this work assumes the gas conversion responsibility Installation of this range must confor
22. fails turn the Knob to OFF and wait until the gas has dissipated e When you set a burner to simmer do not turn the knob quickly Make sure the flame stays on e Do not place any objects other than cookware on the cooktop e This cooktop is designed to cook with a wok or wok ring attachment If foods are flamed they should only be flamed under a ventilation hood that is on e Before removing or changing cookware turn off the burners e Remove food and cookware immediately after cooking e Before removing any parts of the burner for cleaning make sure the range is off and completely cool e After cleaning the burner spreader make sure it is completely dry before re assembling e Make sure the spark mark on the dual burner spreader is placed beside the electrode when it is assembled English 11 Install NX58J7750SS_DG68 00624A 00_EN indd 11 amp 2015 02 04 RR 11 52 28 Important safety information e To avoid carbon monoxide poisoning do not pour water into the cooktop well while cleaning e Select cookware that is designed for top range cooking Use cookware that is large enough to cover the burner grates Adjust the burner flames so that the flames do not extend beyond the bottom of the cookware e To avoid cookware discoloration deformity and or carbon monoxide poisoning do not use cookware that is exceedingly larger than the grate e Make sure cookware handles are turned to the side or rear of the cooktop
23. g parts can be dangerous Please read the important safety instructions for this appliance in this manual The instructions must be followed to minimize the risk of injury death or property damage e Save this manual Please Do Not Discard Symbols used in this manual WARNING Hazards or unsafe practices that may result in severe personal injury or death CAUTION Hazards or unsafe practices that may result in electric shock personal injury or property damage NOTE Useful tips and instructions These warning icons and symbols are here to prevent injury to you and others Please follow them explicitly After reading this section Keep it in a safe place for future reference State of California Propositoin 65 Warning e This product contains chemicals known to the State of California to cause cancer and reproductive toxicity e Gas appliances can cause low level exposure to Proposition 65 listed substances including but not limited to benzene carbon monoxide formaldehyde and soot substances resulting from the incomplete combustion of natural gas or LP fuels Commonwealth of Massachusetts e This product must be installed by a licensed plumber or gas fitter qualified or licensed by the State of Massachusetts When using ball type gas shut off valves you must use the T handle type Multiple flexible gas lines must not be connected in series English 5 Install NX58J7750SS_DG68 00624A 00_EN indd 5 amp 201
24. ge is not to be installed closer than 4 7 in 12 cm from any adjacent surface 5 13 in 33 cm al ola Overhead fe Cabinet 7 in A Depth a Side 76 2 cm Clearance Site Above ke gt le 4 30 in 76 2 cm Cooking 4 in 6 in 18 in Q Surface to 10 2 cm BE 15 2cm 457 cm Wall we D TY 3 MD O in 0 cm 2 Clearance n 36 in ik om Below 91 4 cm Pe zen Cooking Top Oin Depth and at Rear 0 cm p fand Sides of Range English 17 Install NX58J7750SS_DG68 00624A 00_EN indd 17 amp 2015 02 04 RR 11 52 32 Installation requirements Minimum dimensions Exception Installation of a listed microwave WARNING l oven or cooking appliance over the cooktop If overhead cabinets are provided a range shall conform to the installations packed hood should also be provided that projects with that appliance horizontally a minimum of 5 in 12 7 cm beyond the front of the cabinets This will dissipate any heat buildup in the overhead cabinets to prevent death personal injury and or fire hazard The ventilating hood must be constructed of sheet metal not less then 0 0122 thick Install above the cooktop with a clearance of not less than 1 4 between the hood and the underside of the combustible material or metal cabinet The hood must be at least as wide as the appliance and centered over the appliance Clearance between the
25. i tip bracket is properly Gas Range Plug installed and engaged with the range Range is leveled and is firmly sitting on a solid level floor Gas surface burners have been properly assembled All burners have been tested for proper operation FOR INSTALLER ONLY Check and or adjust the broil and oven burner flames as described on page 35 36 in this manual n et o D J n et a zi le u 34 English Install NX58J7750SS_DG68 00624A 00_EN indd 34 amp 2015 02 04 RR 11 52 44 Adjusting the oven burner air adjustment shutters adjustment shutter ua All oven burners have an air adjustment shutter The purpose of the shutter is to regulate the flow of air to the flames Properly adjusted flames should burn steadily with approximately 1 in of blue cone The flames should never extend past the edge of the burner baffles Even though these are preset at the factory they should be checked and if needed adjusted periodically to ensure efficient operation To check and adjust the oven burner air adjustment shutters 1 Open the oven door 2 Remove the oven racks 3 Remove the oven floor 4 Press the Bake pad then the START pad Install NX58J7750SS_DG68 00624A 00_EN indd 35 5 After the oven has lit visually check the flames coming out of the upper and lower burners If adjustment is needed caref
26. ingle Oven 4 a OR cs TI 0 CLEAR Bake amp Roast Broil ba DI Nc Zim e ere Bale cBake AI Foo ATTI in Timer1 Cooking Delay Sake Ne Zout sec Timer 2 Cooking Delay On Off Time Start 02 On Off Time Start as 1 2 3 4 5 e 03 Easy Cook 5 03 A Keep Favorite Self Slow Dehydrate Bread A Le Warm Cook Clean 6 7 8 9 O Clock cook Proof Q 3 Press the START SET button e The gas oven preheats until it reaches the temperature you set e When preheating is complete place the food in the gas oven and then close the door 1 Press the Bake Roast or Bake button 2 If necessary use the number pad to change the default temperature 350 F You can set the oven to any temperature from 175 F to 550 F 4 When cooking is complete press the OFF CLEAR button and then take out the food To start the broil burners Upper Single Over m Warm Favorite Easy 123 Clean Lower Single Oven or 0401 tan come EO p AIEI rn Co 03 i C Roast AM Bake A Roast Broil Beal z AA sec Bake Bake Cake L FDD n a Et Pn Ga Timer1 Cooking Delay Bake LJ jat jat De a pa n sec Timer 2 Cooking Delay on off Time stat 02 On Off Time Start o 1 2 3 4 5 Easy cook 03 1 2 3 A Keep Favorite Self Slow Dehydrate Bread as En Warm Cook Clean 6 7 8 9 O clock Cook proof Q 5 DP u a 1 Put food on a broiling grid in a broiling 4 When on side of the food is browned
27. ire To put out a grease fire turn off the heat source and smother the fire with a tight fitting lid or Use a multipurpose dry chemical or foam type fire extinguisher e If a grease fire should occur in the oven turn off the oven by pressing the OFF CLEAR button Keep the oven door closed until the fire goes out If necessary use a multipurpose dry chemical or foam type fire extinguisher Do not heat Unopened food containers buildup of pressure may cause container to burst and result in injury 3 GT e 3 e gt u w h Lee lt le 5 3 w e Gas safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions If you smell gas e Close the valve and do not use the range e Do not light a match candle or cigarette e Do not turn on any gas or electric appliances e Do not touch any electrical switches or plug a power cord into an outlet English 7 Install NX58J7750SS_DG68 00624A 00_EN indd 7 amp 2015 02 04 RR 11 52 27 Important safety information e Do not use any phone in your building e Evacuate the room building or area of all occupants Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Checking for gas leaks e Leak testing of the appliance shall be conducted accor
28. le malfunctions turn off the oven disconnect the power supply and contact a qualified service technicia 14 English Install NX58J7750SS_DG68 00624A 00_EN indd 14 amp 2015 02 04 RR 11 52 29 gas range components Overview MODEL NX58J7750SS a 0 u 09 5 Q D a fe 3 D fe 5 D 3 t u 01 Display 02 Surface burner knobs 5 pcs 03 Surface burners 04 Oven vent Install NX58J7750SS_DG68 00624A 00_EN indd 15 05 Removable oven door 06 Storage Drawer 07 Oven light 2 pcs 08 Convection fan Convection Heater 09 Oven rack system 10 Bake oven burner 11 Broil oven burner English 15 2015 02 04 RR 11 52 30 Gas range components BTU Ratings 01 Left Front 15 000 BTU 02 Left Rear 9 500 BTU 03 Center 9 500 BTU 04 Right Rear 5 000 BTU 05 Right Front 18 000 BTU 01 02 03 04 05 Ns 7 Cooktop Burner Placement Cooktop Burners under grates Burner Locations and Output Ratings LI a ow u fen J e 0 n e 3 Ke e J D J et u Gas range specifications MODEL NX58J7750SS DESCRIPTION Gas Free Standing Range OVERALL DIMENSIONS 29 13 in W x 46 19 in H x 23 11 in D 757 mm W x 1183 mm H x 602 mm D NET WEIG
29. ly cord from an old range or other appliance e The power cord electric supply wiring must be retained at the range cabinet with a suitable UL listed strain relief A time delay fuse or circuit breaker is also recommended Do not use an extension cord or adapter with this appliance Do not under any circumstances cut modify remove or otherwise defeat the grounding third prong from the power cord If the plug and the outlet do not match or you have any doubt have a qualified electrician install the proper outlet The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded Ground Fault Circuit Interrupters GFCIs are not required or recommended for gas range receptacles u n Dv D ct re x Q D OD u e NEVER connect ground wire to plastic plumbing lines gas lines or water pipes CAUTION Failure to follow these instructions can result in death fire or electrical shock English 21 amp 2015 02 04 RR 11 52 32 Installation requirements Usage situations where appliance Additional installation requirements power cord will be disconnected for mobile homes frequently The installation of appliances designed for Do not use an adapter plug in these mobile home installation must conform situations because disconnecting of the with the Manufactured Home Construction power cord places undue s
30. m with local codes or in the absence of local codes with the National Fuel Gas Code ANSI Z223 1 NFPA 54 latest edition In Canada installation must conform with the current Natural Gas Installation Code CAN CGA B149 1 or the current Propane Installation Code CAN CGA B149 2 and with local codes where applicable This range has been design certified by ETL according to ANSI Z21 1 latest edition and Canadian Gas Association according to CAN CGA 1 1 latest edition Location safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions 3 Ke le fan J u w h D lt le 3 w Si e e This range is for indoor household use only Do not install the range in areas exposed to the weather and or water e Do not install the range in a place which is exposed to a strong draft XX A e Select a level well constructed floor that can support the range s weight Synthetic flooring such as linoleum must withstand 180 F 82 C temperatures without shrinking warping or discoloring Do not install the range directly over interior kitchen carpeting unless a sheet of inch plywood or a similar insulator is placed between the range and carpeting e Select a location where a grounded 3 prong outlet is easily accessible e If the range is located near a window do not hang long curtains or paper blinds on that wi
31. ndow For the range to ventilate properly make sure the range s vents are not blocked and that there is enough clearance at the top back sides and underneath the range The vents allow the necessary exhaust for the range to operate properly with correct combustion 10 English Install NX58J7750SS_DG68 00624A 00_EN indd 10 amp 2015 02 04 RR 11 52 28 e Make sure the wall coverings around the range can withstand heat up to 200 F 93 C generated by the range e Cabinet storage above the surface of the range should be avoided If cabinet storage above the range is necessary allow a minimum clearance of 40 inches 102 cm between the cooking surface and the bottom of cabinets or install a range hood that projects horizontally a minimum of 5 inches 12 7 cm beyond the bottom of the cabinets Cooktop safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions e Make sure all burners are off when not in use e Do not use aluminium foil to line the grates or any part of the cooktop Do not leave burners unattended on medium or high heat settings 3 Ke e 3 e gt u w h Lee lt le 5 3 w e e Before igniting make sure all burner caps are properly in place and all burners are level e Always use the LITE position when igniting the burners and make sure the burners have ignited If ignition
32. ructions Step 8 Check the ignition of surface burners and oven burners Check the operation of all cooktop and oven burners after the range has been installed and assembled gas supply lines have been carefully checked for leaks and electrical power cord has been plugged in All surface and oven burners have electronic ignition 4 N To turn on a surface burner m D 1 Push in and turn the control knob for that N ER surface burner to the LITE position The K clicking sound indicates the electronic e a s ignition system is operating properly The pe cui burner will light in about 4 seconds after the air has been purged from the supply J line 2 After the burner lights turn the control knob to the desired setting The clicking sound will stop and the flame height will change from Max to Min during turning the control knob w Repeat steps 1 and 2 to check the operation of each surface burner in succession NOTE Place food in the oven after preheating if the recipe calls for it Preheating is important for good baking results After the oven has reached the desired cooking temperature it will beep 6 times n et DI D Sh 5 n et a st gt n 32 English Install NX58J7750SS_DG68 00624A 00_EN indd 32 amp 2015 02 04 RR 11 52 42 To start the bake burners Upper Single Over i Warm Favorite B 123 Clean f Lower S
33. rvice or maintenance can cause personal injury or property damage Step 1 Unpack the range Remove all packaging materials Failure to remove packaging materials could result in damage to the appliance Inventory all loose parts against the Parts supplied components listed on page 23 Check for shipping damage and or missing parts Any damage and or missing parts should be reported to your local retailer Install NX58J7750SS_DG68 00624A 00_EN indd 25 NOTE To order parts or accessories contact your local retailer or refer to the last page NOTE To ensure proper installation we strongly recommend that you hire a professional installer Step 2 Connect the range to gas supply Shut off the main gas supply valve before disconnecting the old range and leave it off until the new hookup has been completed Don t forget to relight the pilot on other gas appliances when you turn the gas back on Because hard piping restricts movement of the range the use of a CSA International certified flexible metal appliance connector is recommended unless local codes require a hard piped connection English 25 2015 02 04 RR 11 52 39 3 n et DI D ma n et a eh n 5 un ct o e J3 D Q D 3 D u Installation requirements WARNING If the information in this manual is not followed exactly a fire or explosion may result causing
34. storage Use the oven for cooking purposes only e Make sure the inner portion of the split oven rack is in the proper position within the outer rack e Make sure the oven racks are placed on the same level on each side Do not damage move or clean the door gasket Do not spray water on the oven glass while the oven is on or just after you have turned it off Do not use aluminium foil or foil liners anywhere in the oven Do not use aluminium foil or like material to cover any holes or passages in the oven bottom or to cover an oven rack e Stand away from the oven when opening the oven door e Keep the oven free from grease buildup e When repositioning the oven racks make sure the oven is completely cool e Only use cookware that is recommended for use in gas ovens e To avoid damaging the burner control Knobs always bake and or broil with the oven door closed Do not broil meat too close to the burner flame Trim excess fat from meat before cooking e When using cooking or roasting bags in the oven follow the manufacturer s directions 3 GT e 3 e gt u w h Lee lt le 5 3 w e Storage drawer safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions e Do not use the drawer for non cooking purposes such as drying clothes or storage Use the drawer for cooking purposes only e Do no
35. t is designed Do not attempt to convert the appliance from the gas specified in this manual to a different gas without consulting the gas supplier This range is convertible for use on natural or propane gas If you decide to use this range on LP gas conversion must be made by a qualified LP installer before attempting to operate the range For proper operation the pressure of natural gas supplied to the regulator must be between 5 in and 13 in 13 cm and 33 cm of water column For LP gas the pressure supplied must be between 10 in and 13 in 25 cm and 33 cm of water column Install NX58J7750SS_DG68 00624A 00_EN indd 19 When checking for proper operation of the regulator the inlet pressure must be at least 1 in 2 5 cm greater than the operating manifold pressure as given The pressure regulator located at the inlet of the range manifold must remain in the supply line regardless of whether natural or LP gas is being used A flexible metal appliance connector used to connect the range to the gas supply line should have an 1 D of 0 5 in 1 3 cm and be 5 ft 152 cm in length for ease of installation In Canada flexible connectors must be single wall metal connectors no longer than 6 ft 183 cm in length Do not kink or damage the flexible metal tubing when moving the range 5 wn D a x D Q Si 5 D 3 D J u English 19 amp 2015 02 04 RR 11 52 32 Installation requirements
36. t touch the interior drawer surface or heating element English 13 Install NX58J7750SS_DG68 00624A 00_EN indd 13 amp 2015 02 04 RR 11 52 29 Important safety information e To avoid steam burns use caution when opening the drawer e Do not use aluminium foil to line the drawer Do not use the drawer in the oven Do not put the drawer in the oven during a self cleaning cycle e Do not leave containers of fat drippings in or near the drawer Self cleaning oven safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions e The self cleaning feature operates the oven at temperatures high enough to burn away food soils in the oven The range is extremely hot during a self cleaning cycle Do not touch any surfaces of the range during a self cleaning cycle e Keep children away from the oven during a self cleaning cycle 3 Ke e w J u w h e lt le 3 w Zi le e Before starting a self cleaning cycle remove all racks cookware and utensils from the oven Only porcelain coated oven J racks may be left in the oven Before starting a self cleaning cycle wipe grease and food soils from the oven Do not put the lower drawer into the oven cavity when you run a self cleaning cycle e When opening the door after a self cleaning cycle stand away from the oven e If the self cleaning cyc
37. tant note to the installer e Read all instructions contained in these installation instructions before installing the range e Remove all packing materials from the oven compartments before connecting the electric and gas supply to the range e Observe all governing codes and ordinances e Be sure to leave these instructions with the consumer e Installation of this appliance requires basic mechanical skills DI D H le g2 S le o D a J e Proper installation is the responsibility of the installer e Product failure due to improper installation is not covered under the Warranty Important note to the consumer amp keep these instructions with your user manual for future reference e As when using any appliance generating heat there are certain safety precautions you should follow e Be sure your range is installed and grounded properly by a qualified installer or service technician e Make sure the wall coverings around the range can withstand the heat generated by the range e Cabinet storage space above the surface burners should be a minimum of 30 in 76 2 cm Important note to the servicer The electrical diagram is in an envelope attached to the back of the range 4 English Install NX58J7750SS_DG68 00624A 00_EN indd 4 amp 2015 02 04 RR 11 52 26 Important safety information READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE All electrical and gas equipment with movin
38. te the range if the range or any part of the range is damaged malfunctioning or missing parts e Do not use the range as a space heater This range is to be used for cooking purposes only e Do not use oven cleaners or oven liners in or around any part of the oven e Use only dry pot holders Do not use the range to heat unopened food containers Do not strike the oven glass e When disposing of the range cut off the power cord and remove the door e Unplug or disconnect power before servicing e Make sure all meat and poultry is cooked thoroughly Meat should always be cooked to an internal temperature of 160 F 71 C Poultry should always be cooked to an internal temperature of 180 F 82 C 6 English Install NX58J7750SS_DG68 00624A 00_EN indd 6 amp 2015 02 04 RR 11 52 26 Fire safety WARNING To reduce the risk of fire electric shock personal injuries and or death obey the following precautions D Do not store place or use flammable or combustible materials such as paper plastic pot holders linens curtains gasoline or other flammable vapors or liquids near the range e Do not wear loose fitting or hanging garments while using the range J e To avoid grease buildup regularly clean the vents Do not let pot holders or other flammable materials touch a heating element Do not use a towel or other bulky cloths in place of a pot holder e Do not use water on a grease f
39. train on the and Safety Standard Title 24 CFR Part adapter and leads to eventual failure of the 3280 formerly the Federal Standard for adapter ground terminal Where a standard Mobile Home Construction and Safety two prong wall receptacle is encountered it Title 24 HUD Part 280 or when such is the personal responsibility and obligation standard is not applicable the Standard of the customer to have it replaced with for Manufactured Home Installations a three prong grounding receptacle by latest edition Manufactured Home Sites a qualified electrician before using the Communities and Set Ups ANSI A225 1 appliance latest edition or with local codes In Canada mobile home installation must be in accordance with the current CAN CSA Z240 MH Mobile Home Installation Code Power cord location The power cord for this appliance is located on the back of the range near the bottom right hand corner The 59 in 150 cm power cord will come installed on the range and taped to the back for shipping L Power cord location 5 u chi D Sh fe 5 S Q 3 D 5 t u 22 English Install NX58J7750SS_DG68 00624A 00_EN indd 22 amp 2015 02 04 SD 11 52 33 tools and materials What s in the box Parts supplied ece Surface burner grates 3 Surface burners and caps 5 Flat rack 2
40. ully adjust the air adjustment shutters The shutters are located at the base of the burner manifolds near the back oven wall To adjust the shutter loosen the locking screw and rotate the shutter towards the open or closed position as needed If flames are lifting off the burner ports gradually reduce the air shutter opening until the flames are stabilized If flames are too yellow and or too large gradually increase the air shutter opening until the flames have approximately a 1 in blue cone NOTE If the range is set up for natural gas the flames should burn with no yellow tipping If the range is set up for LP gas small yellow tips at the end of the cones are normal 5 n et a D Sr J n et a gt u English 35 amp 2015 02 04 RR 11 52 44 Installation instructions To adjust flame low setting After the flames are adjusted properly shut off the oven retighten the locking screws replace the oven bottom and racks and close the oven door Identify which burner is exhibiting too high or too low of simmer rate via manifold panel graphics Simmer Set Screw n et o D le J n et a ee ie u 36 English Install NX58J7750SS_DG68 00624A 00_EN indd 36 1 Rotate a knob to LO position and remove the knob from the valve shaft while the flame is lit 2 Carefully push the screw driver into
Download Pdf Manuals
Related Search