DAC-9213-PVM User Manual.book
Contents
1. Figure 2 DAC 9213 PVM Installed in a Sony Monitor Rear View 9 Installation Iss 03 Setup Note Throughout this chapter the term SDI is used universally to indicate either SD SDI or HD SDI signals Cable Connections Overview Connect the cables to the DAC 9213 PVM according to the designations indicated on the chassis label and Figure 3 The input is internally terminated at 75ohm It is not necessary to terminate unused outputs 727 008 Figure 3 DAC 9213 PVM Connections Input Cabling Connect the system signal to the SDI IN BNC on the DAC 9213 PVM Output Cabling Connect the reclocked output BNCs to other devices as required Setup Iss 03 10 Using the supplied 3 BNC male to 3 BNC male 2m cable 727 008 or equivalent connect the component video output from the DAC 9213 PVM to the corresponding component analog monitor input according to the designations indicated on the chassis faceplate and the monitor s input BNCs Refer to Figure 3 Note The Sony monitor component input must be selected and the monitor must be set up for the same format as the DAC 9213 PVM output video format Status and Selection LEDs The front edge of the DAC 9213 PVM has four LED indicators that display the status of the input signals and indicate menu function and configuration selections Figure 4 UP LED e a DOWN LED ro a oom DAC 92132. DAC 9213 PVM Multi Definition SDI to Analog Component Converter for Sony Monitors User Manual ROSS Video Production Technology DAC 9213 PVM User Manual Ross Part Number 9213PVMDR 004 03 e Release Date November 6 2012 The information contained in this manual is subject to change without notice or obligation Copyright O 2012 Ross Video Limited All rights reserved This work is proprietary and confidential to Ross Video Limited its subsidiaries and its other affiliated corporations and may not be copied distributed sold or otherwise used or relied upon without the express written permission of Ross Video Limited Reproduction or reverse engineering of copyrighted software is prohibited Patents This product is protected by the following US Patents 4 205 346 5 115 314 5 280 346 5 561 404 7 034 886 7 508 455 7 602 446 7 834 886 7 914 332 This product is protected by the following Canadian Patents 2039277 1237518 1127289 Other patents pending Notice The material in this manual is furnished for informational use only It is subject to change without notice and should not be construed as commitment by Ross Video Limited Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual Trademarks ROSS is a registered trademark of Ross Video Limited Geartite is a trademark of Ross Video Limited Ross ROSS ROSS and MLE are registe
3. on all three RGB signals Sync On All is set to On or just on the Green channel Sync On All is set to Off Note This setting has no effect on YPgPr signals Disable Auto Mute Use this menu to disable automatic muting of the analog outputs when a standard mismatch occurs When automatic muting is enabled Disable Auto Mute Off the DAC 9213 PVM will automatically mute the analog outputs when the input video standard selected by the user differs from the video standard detected at the SDI input Note f Disable Auto Mute is set to On with an input output mismatch the DAC 9213 PVM will output an invalid signal and the STATUS LED will flash Default Set Use this menu item to reset all user settings to the factory defaults Holding down the Up button for three seconds will reset the user settings to the default values given in Table 3 on page 14 When selecting this option the state of the UP LED will indicate if any settings are not in their default states e Ifthe UP LED is flashing it indicates there is at least one user setting that is not in its default state Ifthe UP LED is lit solid the user settings are in default state Configuration Iss 03 18 Specifications Specifications are subject to change without notification Table 5 DAC 9213 PVM Technical Specifications Category Serial Digital Video Input Reclocked Serial Digital Video Output Parameter Number of Inputs
4. operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense approved by Ross Video Limited could void the user s authority to Notice Changes or modifications to this equipment not expressly operate this equipment CANADA This Class A digital apparatus complies with Canadian ICES 003 Cet appariel numerique de la classe A est conforme a la norme NMB 003 du Canada EUROPE This equipment is in compliance with the essential requirements and other relevant provisions of CE Directive 93 68 EEC INTERNATIONAL This equipment has been tested to CISPR 22 1997 along with amendments A1 2000 and A2 2002 and found to comply with the limits for a Class A Digital device Notice This is a Class A product In domestic environments this product may cause radio interference in which case the user may have to take adequate measures Maintenance User Serviceable Parts Routine maintenance to this GearLite product is not required This product contains no user serviceable parts If the module does not appear to be working properly please contact Technical Suppo
5. 4mV 54 to 714mV 0 to 286mV 350mV to 350mV 0 to 300mV 0 to 700mV PgPr RB 0 to 700mV 350mV to 350mV Sync 0 to 300mV 0 to 700mV 0 to 300mV 0 to 700mV 0 to 700mV 350mV to 350mV Output Video Level 300mV to 300mV 300mV to 300mV Use this menu to adjust the component video output level by up to 25 This setting affects all input standards and output formats Pressing or holding the Up button will increase the output video level on all three analog output signals Pressing or holding the Down button will decrease the output levels This menu has a 2 button quick default to unity the default value Press both Up and Down buttons at the same time and hold for three seconds Force Mono Use this menu to blank the Pg and Pr component output signals This option has no function in RGB format Note that if the DAC 9213 PVM is setup in RGB mode and Force Mono is enabled then the module is switched to YPgPr mode the P and Pr channels will be blanked i e the module remembers option settings even though they may not affect the current operating mode 17 Configuration Iss 03 Setup On Use this menu to control the blanking level of RGB signals in 525i mode only Setup is only valid in the 5251 RGB MII and 5251 RGB NTSC Related output formats Sync On All Use this menu to enable horizontal synchronization pulses bi level sync or tri level sync
6. D display Table 3 Function Setup and Configuration Menu Function LED Display Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN UP Position Operation Buttons perform no action 625i 720p Input Video 1080psf 23 98Hz Standard 1080psf 24Hz 1080i 50Hz 1080 59 94Hz 1080i 60Hz Auto detect RGB NTSC Related Output RGB MII Video Format RGB N10 No setup YPpPrR N10 No setup Configuration Iss 03 14 Table 3 Function Setup and Configuration Menu Function LED Display Selection Function Up Down Buttons Mode Switch Menu Selection Menu DOWN Position Max Gain Gain between Unity and Max Output Video Level UY Gain between Min and Unity Min Gain Force Mono Setup On Syncon All Disable Auto Mute Not implemented Not implemented Not implemented Not implemented Not implemented Not implemented Not implemented Reset all user settings to Default Set Factory Default state h See Notes Unity 15 Configuration Iss 03 Function Menu Notes Some of the menu items in Table 3 are explained here in further detail as follows Operation In this menu position the Down and Up buttons are disabled Input Video Standard Use this menu item to select the video standard that matches the incoming SDI signal s video standard In Auto Detect mode the module will at
7. Hz Group Delay SD lt 20ns to 6MHz HD lt 6ns to 30MHz Outputs Short Circuit Protected Yes RMS Noise unweighted Required Voltage SD lt 55dB 0 6 0MHz 6V DC supplied by Sony monitor Current Consumption lt 750mA typical Total Power Thermal Environment lt 4 5W typical 20 C to 40 C 68 F to 104 F ambient non condensing Dimensions approx 16 5cm x 5cm 6 5 x 2 Specifications Iss 03 20 Service Information Warranty and Repair Policy The GearLite DAC 9213 PVM is warranted to be free of any defect with respect to performance quality reliability and workmanship for a period of THREE 3 years from the date of delivery to the customer In the event that your GearLite DAC 9213 PVM proves to be defective in any way during this warranty period Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics Should you find that this GearLite DAC 9213 PVM has failed after your warranty period has expired we will repair your defective product should suitable replacement components be available You the owner will bear any labor and or part costs incurred in the repair or refurbishment of said equipment beyond the THREE 3 year warranty period In no event shall Ross Video Limited be liable for direct indirect special incidental or consequential damages includin
8. PVM PWRLED pe Figure 4 DAC 9213 PVM Front Edge Status Indicator LEDs Table 2 describes the status LEDs available on the DAC 9213 PVM 11 Setup Iss 03 Table 2 Status LED Descriptions Function When lit this LED indicates a valid input signal is present and no errors are detected The DAC 9213 PVM is functioning correctly When flashing green this LED indicates an input signal problem or an inconsistency between the SDI input standard and the selected output format Flashing Green When unlit this LED indicates a loss of power to the or DAC 9213 PVM Yellow For menu items that have multiple selections these LEDs will be in a state as indicated in the Function Yellow Setup and Configuration Menu When lit this LED indicates that the DAC 9213 PVM is powered on When unlit this LED indicates a loss of power to the DAC 9213 PVM a A valid signal is defined as any analog composite video signal standard input into the DAC 9213 PVM which matches the setting of the Video Standard that has been selected in the Function Setup and Configuration Menu In other words if the converter is in its default state for NTSC 525 60 video then only an NTSC 525 60 composite video signal input will cause the OK LED to be lit Any other analog composite video signal of a different stan dard PAL B PAL M PAL N that is input into the converter will be invalid Setup Iss 03 12 Configuratio
9. Specification 1 Signal Standards Supported SMPTE 259M 270Mbps SMPTE 292M 1 4835Gbps 1 485Gbps Signal Formats Supported SD 525i 5994Hz 525i 60Hz 625i 50Hz HD 720p 59 94Hz 720p 60Hz 1080psf 23 98Hz 1080psf 24Hz 1080i 50Hzz 1080i 59 94Hz 1080i 60Hz Input Impedance 75ohm terminating Return Loss gt 20dB to 270MHz gt 15dB to 1 485GHz Equalization using Belden 1694A cable Number of Outputs gt 300m 270Mbps gt 100m 1 485Gbps 2 reclocked Signal Standards Supported Follows SDI input SMPTE 259M 270Mbps SMPTE 292M 1 4835Gbps 1 485Gbps Output Impedance 75ohm terminating Return Loss gt 18dB to 270MHz gt 16dB to 1 485GHz Signal Level 800mV 10 DC Offset lt 50mV Rise and Fall Time SD lt 700ps typical HD lt 270ps typical Overshoot Undershoot lt 10 typical Outputs Short Circuit Protected 19 Specifications Iss 03 Yes Table 5 DAC 9213 PVM Technical Specifications Category Analog Component Output Parameter Number of Outputs Specification 3 Video Component Analog Video YPgPr or RGB Supported Video Levels YPgPr SMPTE RGB SMPTE MII Betacam Output Impedance 750hm Output Return Loss gt 45dB to 6MHz gt 28dB to 30MHz DC Offset for RGB or Component Video lt 50mV Frequency Response 0 5dB to 20MHz 1 0dB to 30M
10. Table 1 lists the models supported by the DAC 9213 PVM Table 1 Supported Sony Monitors Model Description 9 4x3 HD Capable BVM D9H1U 5U BVM D14H1U 5U 14 4x3 HD Capable BVM 14L5 1 14 4x3 HD Capable BVM 20L5 1 20 4x3 HD Capable PVM 14L5 1 14 4x3 HD Capable PVM 20L5 1 20 4x3 HD Capable Installation Iss 03 8 Installation The DAC 9213 PVM installs on the rear of your Sony monitor To install the DAC 9213 PVM 1 2 3 Power off your Sony monitor On the rear of the monitor locate the adapter input slot s Using your fingers or a slot screwdriver unscrew the thumbscrews at the top and bottom of the left most input slot cover Remove the cover and store it in a convenient location Insert the DAC 9213 PVM in the left most slot until the edge connector on the rear of the module seats firmly in the monitor s connector socket Note f any other Sony option modules are installed they must be installed from the left and then the DAC 9213 PVM is installed Sony monitors will only recognize option modules from the left towards the right If the monitor finds an option slot empty it will not recognize any other modules to the right of the empty slot 6 When the DAC 9213 PVM is seated level and flush with the monitor s rear surface tighten the thumbscrews to secure the module 09
11. ath or serious injury Caution The symbol with the word Caution within the equipment manual indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Warning Hazardous Voltages This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons ESD Susceptibility This symbol is used to alert the user that an electrical or electronic device or assembly is susceptible to damage from an ESD event gt FP EP EP B Important Safety Instructions A 1 a PF YN 10 11 12 13 14 15 Warning Read these instructions Keep these instructions Heed all warnings Follow all instructions The safe operation of this product requires that a protective earth connection be provided A grounding conductor in the equipment s supply cord provides this protective earth To reduce the risk of electrical shock to the operator and service personnel this ground conductor must be connected to an earthed ground Do not defeat the safety purpose of the grounding type plug A grounding type plug has two blades and a third grounding prong The third prong is provided for your safety If the provided plug does not fit in to your outlet consult an electrician for replac
12. ement of the obsolete outlet Protect the power cord from being walked on or pinching particularly at plugs convenience receptacles and point where they exit from the apparatus Warning Indoor Use WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Do not block ventilation openings Install in accordance with manufacturer s instructions Do not install near heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not use this apparatus near water Only use attachments accessories specified by the manufacturer Unplug this apparatus during lightning storms or when unused for long periods of time Clean only with a dry cloth To avoid electrical shock disconnect the A C power cord before any servicing Refer all servicing to qualified personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug damage liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped EMC Notices United States of America FCC Part 15 This equipment has been tested and found to comply with the limits for a class A Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is
13. g loss of profits incurred by the use of this product Implied warranties are expressly limited to the duration of this warranty This DAC 9213 PVM User Manual provides all pertinent information for the safe installation and operation of your GearLite Product Ross Video policy dictates that all repairs to the GearLite DAC 9213 PVM are to be conducted only by an authorized Ross Video Limited factory representative Therefore any unauthorized attempt to repair this product by anyone other than an authorized Ross Video Limited factory representative will automatically void the warranty Please contact Ross Video Technical Support for more information In Case of Problems Should any problem arise with your GearLite DAC 9213 PVM please contact the Ross Video Technical Support Department Contact information is supplied at the end of this publication A Return Material Authorization number RMA will be issued to you as well as specific shipping instructions should you wish our factory to repair your GearLite DAC 9213 PVM If required a temporary replacement module will be made available at a nominal charge Any shipping costs incurred will be the responsibility of you the customer All products shipped to you from Ross Video Limited will be shipped collect The Ross Video Technical Support Department will continue to provide advice on any product manufactured by Ross Video Limited beyond the warranty period without charge for the life
14. n Use the Function Select switch and the Down and Up buttons to configure the DAC 9213 PVM to convert analog video signals to SDI Settings are described in the section Function Setup and Configuration Menus on page 14 Refer to Figure 5 for switch and button locations e a Up Button FN Button o m e a m 4 Down Button DAC 9213 PVM 2 PWR Figure 5 DAC 9213 PVM Switch and Button Locations General Operating Rules Please note the following important operating rules for the DAC 9213 PVM The module is properly powered on The module always powers up in the last configuration used Function Selection The factory set default modes of operation are as follows Input Video Standard Auto Detect Output Video Format YPpPp N10 no setup In general only the Output Video Format needs to be set as desired The default Auto Detect input setting is extremely versatile However fixed mode settings are provided for user convenience 13 Configuration Iss 03 Function Setup and Configuration Menus A single press of the Down and Up buttons is a momentary click of the button unless indicated by h Table Legend Press the Up button from the default position Press the Down button from the default position Hold Up or Down button for 2 3 seconds for faster adjustment or special function Factory default state Lit LED display e Unlit LED display X Flashing LE
15. nversion e 2reclocked SDI outputs e 10bit DAC resolution e 11bit data processing e Automatic input cable equalization gt 300m gt 984ft of Belden 1694A at SD SDI rates 270Mbps e Automatic input cable equalization gt 100m gt 328ft of Belden 1694A at HD SDI rates 1 485Gbps Analog component outputs can be set for YPgPr or RGB Sony monitor input slot compatible form factor LEDs for power and status Small brick form factor SV universal adapter with locking DC connector e 3 year warranty 7 Introduction Iss 03 Installation Static Discharge Whenever handling the DAC 9213 PVM and other related equipment please observe all static discharge precautions as described in the following note to sensitive semiconductor devices Avoid handling circuit boards in f ESD Susceptibility Static discharge can cause serious damage high static environments such as carpeted areas and when wearing synthetic fiber clothing Always exercise proper grounding precautions when working on circuit boards and related equipment Unpacking Unpack each DAC 9213 PVM module you received from the shipping container and check the contents to ensure that all items are included If any items are missing or damaged contact your sales representative or Ross Video directly Compatibility The DAC 9213 PVM is compatible with Sony monitors which can accept Sony model BKM 120D SDI and BKM 142 HD SDI input modules
16. of the equipment 21 Service Information Iss 03 Notes Service Information Iss 03 22 Gearite A Contact Us Contact our friendly and professional support representatives for the following Name and address of your local dealer Product information and pricing Technical support e Upcoming trade show information Telephone Technical After Hours Emergency Support i Email Telephone General Fax Information Email Website Visit Us Visit our website for Company information and news 1 613 652 4886 1 613 349 0006 techsupport rossvideo com 1 613 652 4886 1 613 652 4425 solutions rossvideo com http Awww rossvideo com Related products and full product lines e Online catalog Testimonials ROSS Video Production Technology
17. red trademarks of Ross Video Limited Sony is a trademark of Sony Corporation e VELCRO is a registered trademark of Velcro Industries B V All other product names and any registered and unregistered trademarks mentioned in this manual are used for identification purposes only and remain the exclusive property of their respective owners Important Regulatory and Safety Notices to Service Personnel Before using this product and any associated equipment refer to the Important Safety Instructions listed below to avoid personnel injury and to prevent product damage Product may require specific equipment and or installation procedures to be carried out to satisfy certain regulatory compliance requirements Notices have been included in this publication to call attention to these specific requirements Symbol Meanings Protective Earth This symbol identifies a Protective Earth PE D terminal which is provided for connection of the supply system s protective earth green or green yellow conductor This symbol on the equipment refers you to important operating and maintenance servicing instructions within the Product Manual Documentation Failure to heed this information may present a major risk of damage or injury to persons or equipment Warning The symbol with the word Warning within the equipment manual indicates a potentially hazardous situation which if not avoided could result in de
18. rt using the numbers listed under the Contact Us section on the last page of this manual All GearLite products are covered by a generous 3 year warranty and will be repaired without charge for materials or labor within this period See the Warranty and Repair Policy section in this manual for details Environmental Information The equipment that you purchased required the extraction and use of natural resources for its production It may contain hazardous substances that could impact health and the environment To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources Ross Video encourages you to use the appropriate take back systems These systems will reuse or recycle most of the materials from your end of life equipment in an environmentally friendly and health conscious manner The crossed out wheeled bin symbol invites you to use these systems If you need more information on the collection reuse and recycling systems please contact your local or regional waste administration You can also contact Ross Video for more information on the environmental performances of our products Introduction Overview The DAC 9213 PVM Multi Definition SDI to Analog Component Converter for Sony Monitors is a high quality signal conversion solution for High Definition HD and Standard Definition SD SDI signals and part of a growing family of GearLi
19. te Multi Definition MD self contained small brick format modules The DAC 9213 PVM is designed to fit into an HD compatible Sony monitor s adapter input slot The DAC 9213 PVM provides a monitoring quality MD SDI component monitoring solution in a small stand alone package The DAC 9213 PVM addresses program stream imaging requirements by converting 10bit MD SDI video to analog component video multiple formats The DAC 9213 PVM has a full 10bit data path with 11bit data processing The front panel of the DAC 9213 PVM chassis provides power and status LEDs for visual reference In addition user selectable switch settings are available to select the preferred mode of operation The DAC 9213 PVM provides analog conversion of 525i 6251 720p 10801 and 1080p SDI signals SMPTE 259M and SMPTE 292M The DAC 9213 PVM also has two re clocked SDI outputs Special measures have been taken to ensure excellent return loss at both input and output This ensures error free performance with short or long cables Simplified Block Diagram ANLG CVBS Y G OUT RECLOCKER CONVERSION SDIIN 6 amp MT ANLG CVBS P B OUT DESERIALIZER processinc ANLG CVBS P R OUT RECLOCKED SDI OUT 1 RECLOCKED SDI OUT 2 Figure 1 Simplified Block Diagram of DAC 9213 PVM Functions Introduction Iss 03 6 Features The DAC 9213 PVM includes the following features HD SDI and SD SDI to analog component co
20. tempt to detect any of the supported incoming HD SDI or SD SDI video standards Refer to Table 4 for supported standards When a supported standard is detected the appropriate analog output format is selected If the module is unable to determine the input standard the STATUS LED will flash and the module will mute the analog outputs Note f Disable Auto Mute is set to On with an input output mismatch the DAC 9213 PVM will output an invalid signal and the STATUS LED will flash Output Video Format Use this menu to select the output component video format Note that not all output formats support all SDI input signal standards For example RGB NTSC Related is only supported on 5251 Refer to Table 4 for a list of supported standards Note The Sony monitor s component input must be selected and the monitor must be set up for the same format as the DAC 9213 PVM output video format Configuration Iss 03 16 Digital Input Standard Table 4 Supported Formats and Input Standards Analog Output Format Y G setup RGB YPgPr SMPTE EBU N10 0 to 700mV 0 to 700mV 54 to 700mV NTSC Related 0 to 714mV 54 to 714mV SMPTE EBU N10 0 to 700mV Pp B setup 0 to 700mV 0 to 700mV 54 to 700mV 0 to 714mV 54 to 714mV 350mV to 350mV PRR setup YIG 0 to 700mV 0 to 300mV 0 to 700mV 54 to 700mV 0 to 300mV 0 to 700mV 0 to 71
Download Pdf Manuals
Related Search