2000DVR - NorthEast Security Systems
Contents
1. 9 4 Camera 1 Pressing this button will display a full screen image of that camera selection amp PTZ camera e ON LIGHT ON control OFF LIGHT OFF OPEN IRIS OPEN e CLOSE IRIS CLOSE NEAR FOCUS NEAR e FAR FOCUS FAR WIDE ZOOM IN TELE ZOOM OUT 2 Control PTZ camera Each button is assigned for each PTZ command e SET SET PRESET CLEAR CLEAR PRESET GOTO GOTO PRESET AUTO AUTO SCAN e F1 USER 1 e F2 USER 2 e F3 USER 3 e FA USER 4 5 Record HEC Emergency Record at continuous 60ips SUPER FINE size Playback Stop of Emergency Record and return to Schedule Record from Emergency Record Playback stop PLAY Playback of recorded data on HDD SEARCH Search recorded data on HDD SETUP MENU Set up for SYSTEM MENU or Use to exit the menu Press MENU button before powering off the unit STOP ENTER Selects each menu option NEXT Move to next step Navigate in the menu Reduce or increase the option value in the menu 6 CHAP 2 Function of Each Button 7 LIVE View Control Jog Shuttle Control 9 Jog Shuttle CD RW On Off for PAN TILT ZOOM control mode Press this button first to control PTZ camera connected to DVR unit via RS 485 Zooming an image Freezing an image Switch to split display MODE button changes screen division from to full screen to from 16 split screen Display in PIP Picture in Picture mode2. 15 Access DVR with external IP and Port Port forwarded OMNOOARWD If Router support DDNS user can access Remote Viewer using Domain Information Remote Viewer Internet DSL Modem LAN Router LAN or Gateway IP Share Client Dynamic IP f user fail to access please verify 1 4 15 again When speed is too slow and connection fails after access MENU gt EXTERNAL DEVICE gt TCP IP SETUP gt CONNECTION SETUP Increase value of Timeout to find the most suitable speed 35 CHAP 6 Network Setup 6 2 Remote Viewer program MAIN INTERFACE ZOOM FOCUS IPO CHANNEL amp s TITTELIT h E 1 Power button Press the Power switch to exit the program Please disconnect the live feed before powering off the software 2 Connect button Press the Connect button to view the live images from the DVR These are the same images being displayed on the monitor of the DVR with a delay depending on your internet connection at both the DVR location and from where you re currently accessing 3 Disconnect button Press this button to disconnect from the DVR unit Then you may power off the software 4 Screen Division button Select how many channels to view simultaneously single 4 split 9 split or 16 split When you select a view you will see the Channel Numbers highlighted which determine what channels are currently being viewed 5 Channel number button Select the channel
3. NO OONOOA Remote Viewer Internet Cable Modem Client Dynamic IP f user fail to access please verify 1 3 4 again When speed is too slow and connection fails after access MENU gt EXTERNAL DEVICE gt TCP IP SETUP gt CONNECTION SETUP Increase value of Timeout to find the most suitable speed 34 CHAP 6 Network Setup 3 Dynamic IP of PPPoE DSL DVR doesn t support DSL PPPoE user have to set NETWORK with IP SHARE if user need to access DVR remotely At this time User have to port forward on DVR Please contact IP SHARE Manufacturer if you need to know how to forward port Even though user have Static Dynamic IP if user want to use another device PC through IP SHARE user can set NETWORK as follows Verify if IP address is OK or not with PC before connecting DVR Connect Router IP SHARE to DSL modem as shown the following picture Set the internet connection on Router IP SHARE Refer to the Router Manual Verify if sub group of network in Router is OK or not Connect DVR to Router DVR MENU gt EXTERNAL DEVICE gt TCP IP Set DHCP to MANUAL and go into TCP IP SETUP Verify if MAC ADDRESS starts from 00 0A A2 Input internal IP address which user assigned from Router 10 Set IP PORT 50000 recommended 11 Input GATEWAY of Router 12 Inout SUBNET MASK of Router 13 Go out of MENU SETUP 14 Forward port from Router Refer to the Router Manual
4. User s Manual VER1 0 aChannel Stand Alone DVR Audio USB Backup available The most stable and reliable real stand alone Digital Video Multiplex Recorder Installation amp Safeguards INSTALLATION amp SAFEGUARDS All the safety and operating instructions should be read before the unit is operated Environment Condition for Installation To prevent electric shock or other hazard do not expose units to rain moisture or dust This unit should be located in an area with low humidity and a minimum of dust Place this unit in a well ventilated place and do not place heat generating objects on this unit This unit should not be located in an area where it is likely to be subjected to mechanical shocks Before You Start Ensure the power switch is in the OFF position prior to starting Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Installation should be performed by qualified service personnel only This unit should be operated only from the type of power source indicated on the manufacturer s label and with the power supply included with the unit Notice Be aware thoroughly about the power connection before installation of the unit Before initial configuration or operation you must first set the TIME DATE followed by setting the unit to the FACTORY DEFAULT settings lastly clearing the HDD Please follow these steps
5. Auto camera image sequencing in full screen mode Lock the key function To unlock press longer time for several seconds and then input the password Q Play Play from image recorded 2 minutes ago in forward Quick Play direction in case recorded in continuous mode AUDIO Select audio channel J SHUTTLE Pressing Jog Shuttle button Ready for use Jog Shuttle In playback mode pressing J SHUTTLE button make images frozen RUN LED on While you operate Jog or Shuttle ACTIVE LED on When J SHUTTLE button is pressed Very easy and convenient search Press J Shuttle button and images in playback pause and then Jog and Shuttle makes it very easy and convenient to search forward or backward fast and slow as user want Data Back up and Firmware Upgrade using built in CD writer CHAP 2 Function of Each Button A en AN 00000 m G00000000 L am 0000000090 m o EN Lowe m RS 485 Connection with PTZ Camera or other external device using RS 485 interface RELAY Output RELAY Output Relay out terminal V A out Relay out terminal V A SENSOR Input Sensor input terminal VGA Connection to VGA Monitor CRT type or TFT LCD monitor Just in case you purchased DVR with VGA option board fixed on the main board of DVR you can connect VGA Monitor to DVR unit ETHERNET Connection to ETHERNET device RS 232C Connection to external
6. CHAP 5 Set Up 2 SCHEDULE SETUP Unless you selected other recording mode DVR system records in Schedule Recording mode In SCHEDULE REC SETUP you set type of recording for every time interval of 2 hours in each day of the week Schedule Recording set by manufacturer is recording continuously at its full recording speed and it means DVR system record continuously at 60 ips in total at 720x240 resolution To set Schedule Recording parameters enter into SYSTEM MENU RECORD SETUP SCHEDULE SETUP and Press the ENTER button 1 SCHEDULE SETUP Set recording type for each recording time interval for a day of the week 2 hours interval SUN MON TUE WED THU FRI SAT Use MODE button to select edit type and move to 00 02 M AM C C C C C 9 the time interval of a day of the week you want to change 02 04 M AM C C 5 C Press ENTER button to select and use or button to change the record type To go next page use NEXT 04 06 M AM C C C C C button 06 08 M AM C C C C C x MODE Edit type 08 10 AM C C C C C TIME CELL Set each time interval of a day of the week WEEK Set a day of the week at once 10 12 AM C C C C C TIME ZONE Set a time slot at once ALL Set page by page at once 1 2 CLEAR ALL Clear page by page MODE CELL BY CELL AY lt gt amp NEXT EDIT amp MODE A ALARM M MOTION C CONTINUES x Unless user press REC button to record
7. Increase value I oso SCHEDULE SETUP DISPLAY SETUP HOLIDAY SETUP SCREEN DISPLAY MONITOR SETUP CONFIGURATION RECORD SETUP HDD MANAGEMENT TIME DATE SETUP DOE CAMERA SETUP EXTERNAL DEVICE INTERVAL SETUP ALARM SETUP FACTORY DEFAULT EVENT POPUP SETUP TCP IP SETUP BUZZER SETUP LANGUAGE ENGLISH RS 232C SETUP PASSWORD SETUP SYSTEM INFORMATION PAN TILT SETUP SELECT MENU A Y amp ENTER SYSTEM MENU 19 CHAP 5 Set Up 5 2 DISPLAY SETUP Setting up parameters for monitor and display on screen Enter into SYSTEM MENU DIPLAY SETUP SCREEN DISPLAY LIVE MONITOR SETUP PLAYBACK VGA SETUP COLOR BAR TEST SELECT MENU A Y amp ENTER 1 SCREEN DISPLAY Setting up the screen display in LIVE mode and PLAYBACK mode Select the sub menu which you would like to set using direction buttons and then change ON OFF with ENTER button 1 TIME DATE Display time amp date 2 DVR STATUS Display system setting status 3 ICON DISPLAY Display function setting status 4 REC PLAY BAR Display record playback status 5 CAMERA TITLE Display camera title 2 MONITOR SETUP VGA SETUP VGA option card enables to connect TFT LCD monitor or CRT type PC monitor to DVR unit To connect TFT LCD monitor or CRT type PC monitor to DVR unit select resolution as follows using or button After setting the below option press ENTER button then the DVR un
8. User can print current image user selected c EXIT Return to Back up CD Player mode 42 CHAP 7 Programmer reference CHAP 7 Programmer reference Q Je 1 Connector Pin Assignment Description NO Description No 1 DCD Data Carrier Detect 6 DSR Data Set Ready 2 RxD Receive data 7 RTS RS232C Rx Tx data Transmit data 8 CTS RS232C Rx Tx data 4 DTR Data Terminal data 9 5 GND Signal Ground 2 RS232 ASCII CODE We qualify that the ASCII information is provided only as reference material for programmers to aid them in using these RS 232 ASCII primitive commands for integration into user developed software and applications The following table is based on 16ch DVR All ASCII Code is 1 Byte me a oom v rz r Mo oe s ow e sro s ur zoom z uox o oe s ons gt me e ron x rz y ou v om 7 owe s ease wwe w woe o en v oe s ons Fm emm ow m v we z ow ome pwenu fw lt ce s en v we ful gt jssu v oe j om vr Jog Shuttle Please input L command to activate J SHUTTLE function using keyboard of PC amp 0 enter amp 1 enter scr Tonto amp 3 enter amp gt 3 enter amp lt 4 enter sc tent Shuttle Right 50 deoree amp gt 5 enter Shuttle Left 60 degree amp 6 enter Shuttle Right 60 degree amp 6 enter Shuttle Left 70 degree amp T7 enter
9. included in package on the bottom of case and then install the HDD on top of them by using the bolts included in package 5 Screws must be inserted from outside of the case bottom 10 CHAP 3 Installation 3 Camera 4 Monitor sesees ses an pM Connect the video output marked MONITOR to Video In of Main monitor 5 Power LL OLET HI noo Connect one DC 12V 6 67 A Adaptor to the back side of Power Jack for right operation of 2HDDs and CDRW oog Before you turn on the Power switch be sure all necessary devices such as Power adaptor cameras and Monitor are connected properly to DVR iiid Notice To avoid accidental deletion of HDD data please make sure to press MENU button before powering off the unit This takes the unit out of record mode for safe shutdown 11 CHAP 3 Installation 6 SPOT VIDEO PRINTER Connection with additional composite monitor 7 Other External Device RS 232C Control DVR through RS 232C port by using PC LILHIEJEEICIHTIH RS 485 Control external device like PTZ Camera R
10. LIVE Display a NORMAL ENHANCED 60 50 IPS 720x240 720x288 LL 120 100 IPS 360x240 360x288 Camera Title ull SUPER FINE Picture Quality Q SA MOTION Record BASIC CONTINUOUS Record H 240 200 IPS 360x120 360x144 4 4 Live View Setup 1 Full Multiple View Switch to multi screen display by pressing MODE For full image display just press the channel button which you want or continue to press MODE button until you see full screen When you playback images which recorded in 360X240 360X288 resolution only 4 amp 9 split screens are available HA NL Multiple screen changes 14 CHAP 4 Operation 2 View in Sequence Press SEQ button It automatically displays full screen images in sequence CH08 3 Picture in Picture PIP View When it is in full screen display mode you can see other camera in a small window by pressing PIP The other camera in small window is rotating in sequence to next number of camera and you can set the rotating time interval as per the procedure in SYSTEM MENU CONFIGURATION INTERVAL SETUP 4 Freeze View Full display mode If you press the FRZ button the FRZ icon will be activated on the screen and F character will be shown beside camera title and live image will be frozen Split display mode If you press the FRZ button the FRZ icon will be activated on the screen press the channel button which you want to freeze To rele
11. and recording In normal camera condition itis ACTIVE but LOSS is displayed when the cable is disconnected or camera is not working LIVE Decides whether to show LIVE screen image or not REC Decides whether to record relevant channel or not 4 MOTION SETUP You can set sensitive of motion detection in 4 steps motion detection area and others in relation to motion recording in this menu 4 1 MOTION SETUP SENSITIVITY GRADE Adjusts motion detection sensitivity LOW MEDIUM HIGH VERY HIGH MOTION DISPLAY TYPE Showing cells with motion detected differently from cells with no motion RECORD DURATION Whenever motion is detected and it is set at Motion Recording mode DVR system records for RECORD DURATION from time motion is detected 1sec 99 sec Default duration 5 sec 4 2 MOTION MASK SETUP Set motion detection area Direction button is for moving and ENTER button is for selection and MODE button is for changing mode of MASK SETUP CELL Move to the location which you want to detect and then press the ENTER button Highlighted cell area means motion detection area ALL ON Set all cells as detection area Use ENTER button to set ALL OFF Set all cells as no detection area Use ENTER button to set BLOCK ON Select detection area by block Use MODE button and press ENTER button to set ON BLOCK OFF Select un detection area by block Use MODE button and press ENTER bu
12. button first for PTZ control mode Numeric buttons from 1 to 16 and direction buttons are assigned for each PTZ command and user can control PTZ camera connected to DVR unit by pressing any one of those 20 buttons one after the other as needed and it is just like control by separate PTZ controller 17 CHAP 4 Operation 4 9 Data Back Up Enter into SYSTEM MENU BACKUP CDR SETUP 1 Insert empty CD R media into CD writer and select the start time amp date from which you want to back up x The START amp END time date in HDD sub menu only shows start and end of recording This is not selectable and editable x 700MB on CD R sub menu represent size of CD R media inserted 2 To set start time of back up and back up data size press the ENTER button first on START or SIZE sub menu and adjust using or button and move using LEFT and RIGHT button for next change After setting the time amp date and back up data size press the ENTER button again to exit x End of back up time will be calculated automatically as per start time amp date and the back up data size you set x User can select the back up data size size of back up data from start of back up on SIZE item but END of back up time is automatically determined by DVR system 3 Press ENTER button on BURN sub menu DVR system starts burning CD 4 When burning is completed CD R media will come out automatically In the next CD back up start time of CD R sha
13. channel 2 MODEL Select camera model protocol type per each channel 3 PTZ ID Select ID 4 BAUDRATE Select data transmission speed 5 CMD DELAY Select command delay time 30 CHAP 5 Set Up 4 AUDIO SETUP Use direction button to move to channel and Press ENTER button to set ON OFF 1 REC CH REC Sw 1 ON Record images with AUDIO 01 ON ON 2 OFF Record images without AUDIO 02 ON ON 2 PLAY 03 ON ON SE 9n ON 1 ON Recorded sound comes out during playback 2 OFF Recorded images only play back SELECT AV 4 amp ENTER Set the all system parameters as manufacturer first ALL OFF set before delivery It is a kind of system SCREEN DISPLAY OFF initialization and manufacturer recommends to do it CAMERA SETTING OFF when you add new HDD or other changes in MOTION SETUP OFF system to make all system ready for normal PANTILT SERUP OFF operation SCHEDULE SETUP OFF Use direction button to move and Press ENTER CONFIGURATION OFF button to change parameters After move to RUN EUN Press ENTER button for actual Factory Default setting SELECT MENU A Y amp ENTER 5 8 LANGUAGE SETUP The menu can be displayed in a number of languages Press ENTER button to select your language DISPLAY SETUP CONFIGURATION RECORD SETUP EXTERNAL DEVICE FACTORY DEFAULT LANGUAGE ENGLISH SELECT MENU A Y amp ENTER 3 1 CHAP 6 Network Setup CHAP 6 Network Setup 6 1 DV
14. event is activated the full image will pop up as user set 1 CHANNEL Choose a channel CHANNEL CHO01 2 POPUP ON OFF Set a popup function at ON OFF POPUP ON OFF ON EVENT AM 3 EVENT Set event mode which popup function is DURATION 03 applied to A ALARM event M MOTION event 4 DURATION Set the duration how long the popup Image is shown 0 sec 60 sec 3x f more than 2 channels pop up at the same time the first channel out of them will be shown For e g Ch1 and CH3 pop up at the same time CH1 will be shown 24 CHAP 5 Set Up 6 BUZZER SETUP Set parameters for buzzer On or Off Use direction button and ENTER button KEY BEEP buzz when button is pressed VIDEO LOSS buzz when video signal is lost ALARM ACTIVE buzz when alarm is activated MOTION DETECT buzz when motion is detected User can set all buzzers at On Off at once by set ALL at ON OFF 7 PASSWORD SETUP Set user ID and password Use UP and DOWN button to move to option and LEFT and RIGHT button to set user ID The password must be consist of 1 to 8 digit number Just use numbers button from 1 to 10 on the front panel of DVR unit To change password user must input current password and then input new password And input again new password to confirm Default value ADMIN Blank MANAGER 1 USER 1 2 USER 8 9 ALL ON KEY BEEP ON VIDEO LOSS ON ALARM ACTIVE
15. that you want to view based on what Screen Division view is enabled 6 Status window Display s the current time and date based The date is in the format Year Month Day You will also see the status of your connection 7 Setting Playback and Sequence buttons a Setting Enables the software configuration screen b Playback Enables the remote playback screen c Sequence When in single channel view hitting the sequence button will sequence through all active channels at a speed specified in the settings menu 8 PTZ control You can control a PTZ camera via the software with these controls a First you must input or configure the specific PTZ protocol into the software in order to communicate with the PTZ device b When you press any of the controls for the PTZ please press and hold the button for 1 2 seconds per instance to compensate for the data transmission rate If you do not and instead simply click the PTZ buttons you may get undesired results having the requested operation transmitted repeatedly regardless of your intention c The plus and minus buttons send the PTZ commands to the corresponding PTZ camera ID 36 CHAP 6 Network Setup IP PORT Setting Screen Remote Viewer setup X IP PORT DONS PTZ SAVE NAMIE INTERNET amp MANUAL C DONS ADDRESS 192 168 1 160 PORT 50000 USER ID admin PASSWORD IN TERINE T IP List came MANUAL Input IP address and PORT manua
16. time display per camera Auto Sequence PIP Picture in picture Event Popup Digital Zoom Display Freeze Simple Playback mode Simple PTZ camera control Record Variable Record resolution For higher picture quality or higher recording speed Efficient Image Quality setup in 5 steps Schedule Record Holiday Record Event Record Alarm Motion Emergency Record Network View Live and Playback images across IP network Copy images across the network Playback Search amp Playback by Date Time Event and Camera Outstanding picture quality by JPEG 2000 compression algorithm No mosaic effect Suitable for recording not only images but also text Various steps in Forward Playback Speed X1 16 X1 8 X1 4 X1 2 X2 X4 X16 X32 X64 Various steps in Backward Playback Speed X1 16 X1 8 X1 4 X1 2 X2 X4 X16 X32 X64 Easy and convenient search by Jog Shuttle amp Remote Controller Data Back Up Simple Back Up using built in CD Writer Back up CD Player included in the package Network Back Up using Remote Viewer program Remote Viewer included in the package Supports bigger capacity of HDD 300GB or bigger USB Device Back Up available Others Multi Language English Spanish German French Italy Japan China VGA option board supports both TFT LCD monitor and CRT monitor Lock the system by Password JOG SHUTTLE PAL NTSC Auto detection Control the unit by using Remote Controller Audio recording IN 4ch OUT
17. 1ch mono 1 2 Package Contents CHAP 1 Features amp Package Contents O O 00000 A 000 iS C OOO 000 Q00 OOO OOO QUO 2 OOOO 00008 oooo we 3 Power Cable 1 DVR Main Unit 2 Remote Controller 6 Software CD 4 Power Adapter 5 User s Manual ee a e 7 Rubber Pad 8 HDD absorber 9 Battery for remote controller 10 Bolts Package Contents 1 DVR Main Unit 2 Remote Controller 3 Power Cable Description STAND ALONE DIGITAL VIDEO RECORDER DVR control AC power supply to adapters for 12 V DC power 4 Power Adapter 12 V DC power supply 6 Software CD Remote Viewer Software amp Back up CD player 7 Rubber Pad Prevent DVR from slipping Attach it to the bottom of main unit 8 HDD absorber Absorbing the mechanical shock of HDD against the case bottom 9 Battery Battery for remote controller 10 Rack mount bracket Bolts Rack mount bracket For fixing Rack Mount bracket to DVR 6ea For fixing DVR with Rack Mount bracket to 19 Rack 4ea For fixing Hard Disk Drive into DVR 8ea CHAP 2 Function of Each Button CHAP 2 Function of Each Button o eee o o0
18. AM04 04 12 START 2005 AUG 07 AM04 04 12 END 2005 AUG 08 PM08 12 23 END 2005 AUG 08 PM08 12 23 CD R 700 MB CD R START 2005 AUG 07 AM04 04 12 START 2005 AUG 07 AM04 04 12 END 2005 AUG 08 PM08 12 23 END 2005 AUG 08 PM08 12 23 SIZE 700 MB gt 700MB SIZE 000MB BURN S CD RW BURNING IMAGE DATA SELECT SETUP BUTTON JOG SHUTTLE SELECT SETUP BUTTON JOG SHUTTLE System Status Messages CD RW DOOR CLOSE CHECKING CD R Blank CD check INPUT BLANK CD CD writer has no blank CD CD RW DOOR OPEN Open CD RW and insert blank CD R media into CD drive CD R MEDIA IS DETECTED Blank CD R media has been inserted and detected DVR system will display size of blank CD R After you set START time and SIZE in CD R sub menu and then select BURN DVR system starts copying images to CD and shows following message BURN CD RW BURINING START CD RW BURNING LEAD IN CD RW BURNING IMAGE DATA CD RW BURING CLOSE TRACK CD RW DOOR OPEN When burning is completed CD R media will be ejected automatically To copy more images repeat above process In the next back up process START time in CD R sub menu shall be END time in previous back up and you can copy images in series to many CDs as many as you want xX SIZE Change Change per 10MB unit LEFT RIGHT Change per 100MB unit 2 USB SETUP User can back up the recorded data to USB Media using USB HOST port on f
19. ELAY Output Relay Output Pin No 4 No 6 at Terminal Block SENSOR Input SENSOR Input Alarm connection Pin No 7 No 26 at Terminal Block ETHERNET Connection to LAN WAN Internet VGA Connection to a VGA monitor CRT TFT LCD if optional VGA board is fixed on the main board as shown in the following figur ggo Resolution set by manufacturer is 800x600 60 Hz and user can set resolution in MONITOR SETUP VGA SETUP VGA RESOLUTION c rus Ew LI LIE ELLLIJ ae Audio Input Microphone Input IN1 IN4 Audio Output Speaker Output OUT 12 cca than LI CHAP 4 Operation 4 1 System Log In 1 To enter into the setup menu press the MENU button 2 Enter password with channel number button from No 1 to No 10 on the front of the DVR unit Maximum of 8 digits are available SIME SI RSS 7 INPUT YOUR OWN PASSWORD 3 After inputting the password press the ENTER button TO EXIT PRESS MENU Administrator If the password entered matches previously set password LOGIN ADMIN message appears and you can enter into SYSTEM SETUP If the password entered does not match previously set password the DVR unit goes back to live display mode Factory default password is blank For log in just press MENU button and then ENTER button Factory default password ADMIN Blank MANAGER 1 USER 1 USER8 2 9 x We recommend configuring a unique pa
20. If you want to keep the playback speed you selected using Shuttle just hold the shuttle at that location for a few seconds and playback in speed you selected continues until you rotate Shuttle again 16 CHAP 4 Operation 4 7 Search Press SEARCH button and 3 different methods for searching recorded data are available as shown in following SEARCH window For selecting searching method use direction key or Jog Shuitle After selecting each search method press ENTER button for playback exit press MENU button 1 SEARCH BAR Search by percentage of total recorded data It starts from image corresponding to set of data on the search bar 2 TIME DATE Search by time amp date Playback starts from the time amp date selected 3 EVENT LIST Search by event list Motion Alarm Video Loss SEARCH BAR ee TARGET PERCENT EVENT LIST 020 i 5 SELECT MENU A Y amp ENTER SEARCH ENTER EXIT MENU SEARCH page SEARCH BAR page EVENT TIME DATE 001 000 START 2005 JUN 20 AMO04 04 12 END 2005 JUN 20 PM08 12 23 INPUT TIME DATE 2005 JUN 07 AM04 04 12 SEARCH ENTER EXIT MENU SEARCH ENTER EXIT MENU TIME DATE page EVENT LIST page SSS SS I I I I I I I I I I I SS m CS 0 F 4 8 PAN TILT ZOOM Camera Operation Press PTZ
21. NTERFACE through Remote Viewer DVR Remote Viewer Mon Tue Wed Thr Fri l 1 13 1 18 19i 20 2 e3 24 25 2b e 28 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 3l Function of each button in Search window D Exit Exit to live window 2 Full screen Select a certain camera to view in full screen 3 Quad To view quad mode 4 channels at the same time 4 Time The recording time amp date information of the pictures which is being played 5 Channel selection Select each camera 6 Time selection Select a time from which user want to see The playback will be started from this point drag the point using mouse 7 Start and end time Indicate record starting time and end time of images on HDD Other operating button Refer to the next page description 39 CHAP 6 Network Setup Play fast backward Move to the start of recording Play backward 1X Move to the previous hour Play forward 1X Move to the afterward hour JU Play fast forward Move to the end of recording 3000p Stop playback 9 Command button a SAVE After pressing the Stop button click SAVE button to save the currently viewed image in jpg format b PRINT After pressing the Stop button click PRINT button to print the currently viewed image c RECORD Press this button to download playback images transmitted from DVR unit into your PC Use
22. ON MOTION DETECT ON SELECT A V amp ENTER USER I D ADMIN USER PW NEW PW CONFIRM K1 K10 INPUT PASSWORD ENTER CHANGE PASSWORD TO EXIT PRESS MENU Change the user PASSWORD in the first operation is recommended n case you forgot PASSWORD contact dealer of DVR to get instruction to enter into menu to set new PASSWORD 8 SYSTEM INFORMATION DVR system information including firmware version hardware version product ID etc 25 S W VERSION VER1 0 H W VERSION VER 1 0 PRODUCT ID 01S 2039 001008 AR 01 MASTER Maxtor 6YO60LO SLAVE CD R SAMSUNG CD R RW SW 256B TO EXIT PRESS MENU CHAP 5 Set Up 5 4 RECORD SETUP This is the most important configuration of the DVR K RECORDSETUP e Enter into SYSTEM MENU RECORD SETUP and press the ENTER button SE OPO EIS EN 1 RECORD CONFIGURATION SCHEDULE SETUP HOLIDAY SETUP Use direction button to move and button to set value 1 OVERWRITE Set overwrite or stop recording when the HDD is full 2 MULTIPLEX DUPLEX Playback amp Ethernet TRIPLEX Playback amp Recording amp Ethernet Note E MODE is recommended to playback assi one a iint he images at a maximum frame rate But it makes DVR not to record during search 3 QUALITY Set recording picture quality Actually it is fixing maximum data size of P SUE ON image for each picture quality in 5 steps MULTIPLEX TRIPLEX as follows QUALITY ENHANCED BA
23. R Network Configuration Please call your provider to identify what type of service they are providing you You will need to know following Upload speed For your own knowledge for expected frame rates Download speed For your own knowledge for expected frame rates Addressing For determining what scenario you should follow Router On Site or Just a Modem For determining what scenario you should follow x NOTE If your provider is using PPPOE usually DSL providers you MUST have a IP Share installed on site and follow 3 Dynamic IP of PPPOE DSL for DVR setup and access x PLEASE verify Internet access after installing any new equipment routers switches modems etc PC s TCP IP Setting Before configuring the DVR please fill out the information below if applicable Choose any PC on your network and determine its TCP IP settings IP Address ex 192 168 1 5 Subnet Mask ex 255 255 255 0 Default Gateway ex 192 168 1 1 Next pages are several network scenarios Please identify which scenario your current network falls within and follow the instructions for configuring and accessing your DVR via TCP IP 32 CHAP 6 Network Setup 1 Static IP User input IP address in IP CONFIG SETUP which is assigned from ISP company Verify if IP address is OK or not with PC before connecting DVR Connect LAN cable to DVR after confirmation DVR MENU gt EXTERNAL DEVICE gt TCP IP Set DHCP to MANUAL
24. SIC RESOLUTION 60IPS 720 240 NORMAL RECORD IN ALARM 1 1X I zu RECORD IN MOTION 1 1X SUPER FINE Default quality set by manufacturer i C eon UIs In Emergency recording mode recording quality is SUPER FINE SELECT MENU A Y CHANGE VALUE To send more images via IP network and longer recording time set QUALITY at NORMAL or ENHANCED and record at 360x240 360x288 Data size of image in PAL system is a little bigger than NTSC system but the total recording time is same as in NTSC system 4 RESOLUTION Set recording resolution 60 ips at 720x240 NTSC 50 ips at 720x288 PAL 120 ips at 360x240 NTSC 100 ips at 360x288 PAL 240 ips at 360x120 NTSC 200 ips at 360x144 PAL x It is not possible to see those images in full screen mode in playback Recording in Dual resolution is recommended for higher recoding speed and also to send more images via IP network 5 RECORD IN ALARM Set record speed skip rate in ALARM record mode 6 RECORD IN MOTION Set record speed skip rate in MOTION record mode 7 CONTINUOUS RECORD Set record speed skip rate in CONTINUOUS record mode Set record speed skip rate 1 1x 1 2X 1 999x record speed ex 1 2x R gt S gt R sS ex 1 3x R gt S gt S gt R gt S gt S gt R ex 1 4x R gt S gt S gt S gt R gt S 5S R RECORD S SKIP ex If record resolution is set at 360x240 1 1x 120 ips 1 2x 60 ips 1 3x 40 ips etc 26
25. STEM IS NOT SUPPORTED If File System is not supported SIZE IS LARGER THAN FREE SIZE If back up size is larger than free space x Back Up procedure is the same as CDR Back Up x f Back Up size is larger than 2GB it creates several files It saves by 2GB 5 6 EXTERNAL DEVICE Set parameters of external devices connected to DVR like Ethernet PTZ camera RS 232C etc Use direction button to move to sub menu and Press ENTER button to set 1 TCP IP SETUP TCP IP function enables user to see live pictures and recorded pictures via the internet 1 IP CONFIG SETUP MAC ADDRESS 00 0A A2 00 00 00 IP ADDRESS ee 192 168 001 160 IP PORT Show the network information assigned to the DVR 50000 unit If the DHCP setup status is AUTOMATIC user GATEWAY gt can set the IP port only and if the DHCP setup status 192 168 001 001 is MANUAL user must set all parameters SUBNETMASK gt O For detail procedure of Remote viewer program 255 255 255 000 installation refer to CHAP 6 Software DHCP SETUP program Remote viewer software 29 AUTOMATIC SELECT MENU AY amp ENTER CHAP 5 Set Up DHCP MODE MANUAL TIMEOUT 200 MSEC RETRY COUNT 08 DNS SERVER 000 000 192 168 IP ADDRESS 192 168 001 160 SUBNET MASK 255 255 255 000 GATEWAY 192 168 001 001 SELECT A Y CHANGE VALUE SELECT MENU AY amp ENTER 2 CONNECTION SETUP TIME OUT Adjust TIMEOUT value properly to success
26. Shuttle Right 70 degree amp 7 enter Shuttle Left 80 degree amp lt 8 enter Jog Minus amp enter Jog Plus amp Tenter shuttle After inputting a command once it will keep performing the command until next command Jog It makes the stage staying after one time operation by command input like Button operation 43 CHAP 7 Programmer reference Key Release for PTZ function power on light on power off light off 2 iris open 3 iris close 4 focus near iod focus far KF zoom in T zoom out gt QZ set preset clear preset oto preset ou 9 p To stop transmitting the signal to DVRs via RS232 auto scan e tilt up uu tilt down B pan left TT pan right k 1 Set preset TS U J H K To move where you want to see 9 set preset gt amp Z amp amp To set other preset point 2 Clear preset TS Q BZ amp amp To choose which you want to delete enter 3 Goto preset P o F SZ amp amp To choose where you want to see enter x Reference 1 Funtions where the OSD xx to the right of the function is not seen pressing 1 or 2 will bring it up 2 Operations such as clear preset take affect upon pressing the 0 key causing the last preset to be deleted even though that may not be the desired action Instead use the next key N until clear preset is up then cho
27. YZ lt gt P lt CAMERA ACTIVE SETUP LOTON SOIT CAMERAOt CAM 1 CAMERAO02 CAM 2 CAMERA03 CAM 3 CAMERA04 CAM 4 SELECT MENU AY amp ENTER ENTER SELECT MODE A V select CAMERA 1 TITLE Input Title of each camera Move to channel you want to change using LEFT or RIGHT direction button and then change the title using button When modification is finished press the ENTER button To exit to previous menu press the MENU button 2 COLOR Adjust image color Move to each element using UP DOWN button and adjust using button or Jog shuttle CHANNEL 1 BRIGHTNESS 30 CONTRAST 40 SATURATION 0 CHANNEL Select camera HUE 0 BRIGHTNESS Adjust image brightness 32 31 CONTRAST Adjust color contrast 32 31 SATURATION Adjust color saturation 32 31 HUE Adjust color hue 32 31 SELECT A Y CHANGE VALUE CHAP 5 Set Up CH STATUS LIVE REC CHANNEL 01 EE UIS E SENSITIVITY GRADE 01 01 ACTIVE ON ON 02 ACTIVE ON ON MOTION DISPLAY TYPE OFF oe soe OFF OFF RECORD DURATION 05 SEC 04 ACTIVE ON OFF ELECT amp W CHANGE VALUE 3 CAMERA ACTIVE SETUP With direction button move to option to be changed and press ENTER button to select ON OFF If it is set at LIVE OFF and REC ON DVR system records but does not show live image of set channel STATUS Shows if image from a specific channel is coming for live display
28. ackage Contents Function of Each Button Front Rear Installation Installation Configuration Detailed Installation Rack Mount HDD Hard Disk Drive Camera Monitor Power SPOT Video Printer Other External Device Operation System Log in Factory Default Display Configuration Live View Setup Full Multiple View Sequencing Cameras PIP View Freeze View Zoom View Record Playback Search PTZ Camera Operation Data Back Up Audio Operation c OO O O a 10 10 10 11 11 11 12 12 13 13 13 14 14 14 15 15 15 15 16 16 17 18 18 18 Set Up Entering the Menu Display Setup Screen Display Monitor Setup Configuration HDD Management TIME DATE Setup Camera Setup Interval Setup Alarm Setup Event Popup Setup Buzzer Setup Password Setup System Information Record Setup Record Configuration Schedule Setup Holiday Setup Back Up CDR USB External Device TCP IP Setup RS 232C Setup Pan Tilt Zoom Setup Audio Setup Factory Default Language Setup Network Setup DVR Network Configuration Remote Viewer Program Back Up CD Player Programmers Reference Connector Pin Assignment RS232 ASCII CODE Specification 19 19 20 20 20 21 21 22 22 24 24 24 25 25 25 26 26 27 27 28 29 29 30 30 30 31 31 32 32 36 41 43 43 43 45 CHAP 1 Features amp Package Contents CHAP 1 Features amp Package Contents 1 1 Features Live View Real
29. and go into TCP IP SETUP Verify if MAC ADDRESS starts from 00 0A A2 Inout IP address which is assigned from ISP company Set IP PORT 50000 recommended Input GATEWAY which is assigned from ISP company Input SUBNET MASK which is assigned from ISP company 10 Go out of MENU SETUP 11 Turn off and on Modem Router which is provided by ISP company This is to reset client of MAC from ISP company User have to wait for 30 seconds after turning on 12 Access DVR with Remote Viewer software OMONOOARWD Internet Static IP Remote Viewer Client If user fail to access please verify 1 6 7 8 9 11 again When speed is too slow and connection fails after access MENU gt EXTERNAL DEVICE gt TCP IP SETUP gt CONNECTION SETUP Increase value of Timeout to find the most suitable speed 33 CHAP 6 Network Setup 2 Dynamic IP Verify if IP address is OK or not with PC before connecting DVR Connect LAN cable to DVR after confirmation 3 Turn off and on Modem Router which is provided by ISP company This is to reset client of MAC from ISP company User have to wait for 30 seconds after turning on Turn off and on DVR DVR MENU gt EXTERNAL DEVICE gt TCP IP Verify if MAC ADDRESS starts from 00 0A A2 Set DHCP to AUTOMATIC and detect IP to get Dynamic IP Go out of MENU SETUP after getting IP successfully Access DVR with Remote Viewer software
30. ase frozen image press channel number of frozen image again and press FRZ button to exit FRZ mode 5 Zoom View In full screen press the ZOOM button and move the Selection Frame using J SHUTTLE or Direction keys to the area which you want to enlarge And then press the ENTER button for 2 times enlarged picture To exit Zoom mode just press ZOOM button again Horizontal Movement J SHUTTLE Vertical Movement Hold UP or DOWN button and turn J SHUTTLE 15 CHAP 4 Operation 4 5 Record Recording mode set before delivery by manufacturer Default recording mode is Schedule Recording In this default recording mode it records 24 hours day continuously in weekday and on the weekend Once you press the REC button while you see live view the record type is changed to Emergency Record mode Emergency Record at full resolution in best quality Record type CONTINUOUS SUPER FINE quality Emergency Record RED 60 50 ips at 720X240 720x288 Schedule Record Schedule Record GREEN Record and stop as set time interval and record type in RECORD SCHEDULE SETUP menu Stop Record WHITE Stop Record Recording stopped as set in RECORD SCHEDULE SETUP menu On the screen Emergency Record Red Record Icon and Record LED is lit Schedule Record Green Record Icon 8 and Record LED is lit Record Stop White Icon LO and Record LED is off Motion Rec
31. at full resolution and in SUPER FINE picture quality DVR system records in SCHEDULE Record mode x DEFAULT record mode for each time interval of a day of the week set by manufacturer is CONTINUOUS recording x Record type After power on Schedule record Exit from menu Schedule record End of search or playback Schedule record After pressing STOP button gt Schedule record After pressing REC button Emergency record Continuous recording in full performance 60 50 ips at 720x240 720x288 Users can set national holiday or holidays on calendar to record just as setting for Sunday in SNA 000 100 SCHEDULE REC SETUP SUN MON TUE WED THU FRI SAT Use MODE button to select a month and direction 01 02 button to move to a day and press ENTER button to set a holiday Then color of date shall be changed to LN ul red as Sunday Te i 2 e as 5 ae EDIT HOLIDAY Set as holiday i7 18 19 20 o EOS CLEAR MON DATA Cancel the holiday set per month CLEAR ALL DATA Cancel all holiday set MODE EDIT HOLIDAY The maximum holidays is 100 days SELECT A Y lt P EDIT ENTER 8 MODE 24 25 26 27 28 29 30 CHAP 5 Set Up 5 5 BACK UP 1 CDR SETUP User can back up the recorded data to CD using CD writer installed in DVR Refer to START and END of data on HDD and set copy from time START and size of data copied SIZE and move to BURN and press ENTER button to start copy HDD HDD START 2005 AUG 07
32. device as PC using RS 232C to control the DVR CAMERA Input Connection with camera EN LOOP Output Camera loop out 7 MONITOR Connection with Composite Monitor Output ES SPOT Conteg with additional composite monitor DC P DC 12V 6 67A Adapt 9 DCPower DO 12V 667A Adaptor m 10 POWER Power ON OFF switch for adapters SWITCH To avoid accidental deletion of HDD data please make sure to press MENU button and enter into setup menu before k aiena ofthe unit moo IT This takes the unit out of record mode lori Audio Input Microphone Input 4ch Audio Output Speaker Output 1ch OO E E D COC LE CHAP 3 Installation CHAP 3 Installation 3 1 Installation Configuration aM Se U MIG Speaker Remocon Camera Oi pee zii H Beem RS 232C Lou e SPOT Monitor Composite VGA Monitor P T Gamera Monitor TFT LGD Monitor Printer CHAP 3 Installation 3 2 Detailed Installation 1 Rack mount Ts Hemove 4 bolts on each side cap to install rack mount 2 Attach rack mount bracket to DVH Attach DVH with rack mount bracket to 19 rack 2 HDD 1 Connect Main Board and HDD1 using IDE cable and HDD power cable 2 The jumper setting of HDD1 should be on Master if you install only one HDD 3 The jumper setting of HDD1 should be on Master and HDD2 should be on Slave if you install two HDDs Refer to the above figure 4 Stick the HDD absorber
33. fully access to DVMR unit via Internet line If data transmission speed is high enough leave TIMEOUT value as set by manufacturer 200 msec and increase it if data transmission via Internet line is relatively slow Execute tracert Tracing Route in your PC for IP assigned to DVMR unit and you can figure out how much TIMEOUT value increased RETRY COUNT Set the retry number of times for network connection 2 RS 232C SETUP K S NN SPEED 115200 User can control the DVR via RS 232C port LENGTH 8 Connect DVR to PC via RS 232C port and control STOP BIT 1 DVR using keyboard of PC PARITY NONE This function is mainly for programmer who wants to control DVR as part of many devices connected to PC system as in SI project 3 PANITILT SETUP lt is to set parameters for PTZ camera connected to DVR unit DVR unit already includes all protocols of well known PTZ cameras like PELCO D type PTZ camera and user just select MODEL and set other parameters to control this PTZ cameras using operation buttons on the front panel of DVR If PTZ camera whose protocol is not incorporated into this DVR unit user must input protocol of this PTZ camera by himself Using USB device port user can upgrade protocol for PTZ camera CHANNEL MODEL as D PTZ ID 000 COMMAND SETTING lt PTZ camera set BAUDRATE 2400 BPS CMD DELAY 1 MSEC SPEED SETTING lt PTZ speed set COMMAND PAN TILT STOP LENGTH 0 7 CODE FF 00 00 00 00 00 00 00 1 CHANNEL Select
34. in order Before installing a second HDD ensure that the drive conforms to the specifications listed on the specifications page at the end of this manual When installing a second HDD set the drive to SLAVE After installation first reset the TIME DATE followed by resetting the unit to the FACTORY DEFAULT settings lastly clearing the new HDD Pull the unit out of record mode prior to cutting power to the unit Do this by entering the setup menu followed by switching the unit off Powering off the unit while writing to the disks can cause critical malfunctions ex Recording Error Playback Error System Error When you set the record type you have to set the Record Configuration and also schedule Setup This unit records as per the Record type amp Schedule setup The REC button on the front panel is for emergency record using highest image quality AN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of this equipment that there are dangerous voltages within the enclosure which may be of sufficient magnitude to constitute a risk of electric shock N The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance Servicing instructions in the literature accompanying the appliance CHAP 1 1 2 CHAP 2 2 1 CHAP 3 4 7 4 8 4 9 4 10 Features amp Package Contents Features P
35. it will set VGA resolution automatically VGA option card supports following resolution and choose best resolution that match TFT LCD monitor or CRT type PC monitor to be connected to DVR unit 640X480 60Hz 640X480 75Hz x NOTICE In the booting process 800x600 60Hz 800X600 75Hz DVR unit with VGA option 1024X768 60Hz 1024X768 75Hz card takes some seconds more to set parameters COLOR BAR TEST Adjust color tone of monitor Color bar test is Not available for monitor through VGA 20 CHAP 5 Set Up 5 3 CONFIGURATION Various parameters for system can be set in CONFIGURATION menu Enter into SYSTEM MENU CONFIGURATION and press the ENTER button ss SETUP HDD MANAGEMENT HDD INFORMATION TIME DATE SETUP CAMERA SETUP INTERVAL SETUP ALARM SETUP EVENT POPUP SETUP CAMERA TITLE BUZZER SETUP CAMERA SETTING PASSWORD SETUP CAMERA ACTIVE SETUP SYSTEM INFORMATION MOTION SETUP SELECT MENU A Y amp ENTER 1 HDD MANAGEMENT Enter into SYSTEM MENU CONFIGURATION HDD MANAGEMENT and press the ENTER button 1 HDD SETUP This page includes information about start and end of recording location of recorded data or location of last playback on HDD In addition users can delete all the data on HDD sere On the HDD CLEAR sub menu press the ENTER button to delete all image data on HDD a ee MAN The system will ask password for verification BEGIN MASTER 2005 04 08 After you clear a
36. ll be the end time of previous CD back up and you can back up from that for continuous data back up If you need another backup repeat the above procedure To stop backup press the MENU button x During burning CD it s impossible to cancel burning process 5 User can verify the back up CD on PC with BACK UP CD PLAYER Included in Package HDD HDD START 2005 AUG 07 AM04 04 12 START 2005 AUG 07 AM04 04 12 END 2005 AUG 08 PM08 12 23 END 2005 AUG 08 PM08 12 23 CD R 700 MB CD R START 2005 AUG 07 AM04 04 12 START 2005 AUG 07 AM04 04 12 END 2005 AUG 08 PM08 12 23 END 2005 AUG 08 PM08 12 23 SIZE 700 MB gt 700MB SIZE 000MB BACKUP MEE BACKUP CD RW BURNING IMAGE DATA EXIT MENU EXIT MENU 4 10 Audio Operation Press AUDIO button to select audio channel Ch1 Ch2 Ch3 Ch4 or silence in due sequence X Sound of the selected audio channel comes out in Live display Recorded sound comes out in Playback 18 CHAP 5 Set Up CHAP 5 Set Up 5 1 Entering into the Menu Enter into SYSTEM MENU by pressing MENU button Selection key Move to sub menu change status ON or OFF UP Movetoupperside I Jog Shuttle Jog left turning Move backward to next image Decrease value Jog right turning Move forward to next image Increase value Shuttle left turning Decrease playback speed Decrease value Shuttle right turning Increase playback speed
37. ll data on HDD status of HDD CLEAR 12 12 05 changes from IN USE to EMPTY RECORD MASTER 2005 04 09 x When you clear HDD event list is deleted too 15 09 58 PLAY MASTER 2005 04 08 Kasa ENTER PASSWORD OK HDD STATUS NORMAL INPUT YOUR OWN PASSWORD HDD CLEAR IN USE TO EXIT PRESS MENU HDD CLEAR ENTER EXIT MENU If you selected OVERWRITE in Record Setup the HDD STATUS presented as OVERWRITE OOOO EN IS MASTER This menu will show the physical information MODEL Maxtor 6Y080L0 SPEED PIO 4 of HDD in DVR SIZE 81 964 302 336 BYTES START 2005 04 08 12 08 56 END 2005 04 08 12 08 56 SLAVE MODEL AT5520026DT SPEED 240 120nsec SIZE 80GB START 2005 04 08 12 08 56 END 2005 04 08 12 08 56 TO EXIT PRESS MENU CHAP 5 Set Up 2 TIME DATE SETUP Set time and date of DVR system which is very EE TIME DATE SETUP important for search with time and date of the event Time and date set by manufacturer is different from Mantes local time of user and user must set time and date DAY 2005 JUN 11 1 1 1 1 E HOUR exactly in the first operation Set time amp date using MINUTE PM14 06 45 direction buttons and button or Jog shuttle SECOND DATE FORMAT ASIA 2 Change the date time and month format for TIME FORMAT 12 HOUR MONTH FORMAT ENGLISH user s convenient SELECT amp W CHANGE VALUE 3 CAMERA SETUP CAMERA TITLE CAMERA SETUP 0123456789 ABCDEFGHIJKLMNOPQ RSTUVWX
38. lly DDNS Receive IP address and PORT from DDNS Server For further information of DDNS please contact your vendor Name Name of IP address on the list Address Input IP address which is set on DVR PORT Input PORT which is set on DVR ID Input ID which is set on DVR Please input admin Password Input password which is set on DVR IP List It shows IP list which user input manually Select Button Select IP and PORT on the list Save Button Save IP and PORT on the list Delete Button Delete IP and PORT on the list 37 CHAP 6 Network Setup PTZ SAVE Setting Screen Remote Viewer setup X IP PORT DONS PTZ SAVE OPTION Circular Monitoring Interval Scan Hate PTZ Type PT2 Baudrate ove aet Path to save Downloaded image c Wnprogram filesttremoteviewertbackup zs Run in Full Screen Mode DK Cancel Circular Monitoring Interval This indicates the speed of the channels sequence when the SEQUENCE button is used from the main interface Scan Rate Set speed of playback PTZ TYPE Select PTZ camera which is connected to DVR PTZ Baud Rate Enter the Baud Rate of your PTZ camera Set Path to Save Downloaded image Determines the location and folder on your PC where the downloaded video clips are stored Run in full screen mode When checked this will enable the program to re adjust the interface to completely fill your computer screen 38 CHAP 6 Network Setup PLAYBACK I
39. ord Alarm Record Alarm Motion Record Record standby LED blinks Record LED is lit x While in Emergency Record mode press STOP PLAY MENU or SEARCH button to exit from Emergency Recording mode and return to Schedule Record mode x For details refer to the SYSTEM MENU RECORD SETUP Page 27 This DVR unit does not record in following conditions x While entered in the Menu x No camera is connected x Overwriting is off in the Record Setup menu 4 6 Playback On record mode or stop mode press PLAY button to play the recorded data in 1x speed For backward playback press PLAY button again Use Jog Shuttle to pause and control playback speed To stop playback press the STOP button Using Jog Shuttle press the J SHUTTLE button in playback mode The ACTIVE LED will be lit and Jog Shuttle is ready for use The RUN LED will blink whenever you operate the Jog Shuttle For forward playback turn the Shuttle right and turn Shuttle left for backward playback Turn Jog using your index figure to see picture by picture in forward or backward direction Operation of Shuttle is as follows 1 4 x 4 times slower than normal playback speed 1 2x 2 times slower than normal playback speed 1 x Normal playback speed 2x 2times faster than normal playback speed 4 x 4 times faster than normal playback speed 16x 16 times faster than normal playback speed 64 x 64 times faster than normal playback speed
40. ose the preset to be deleted followed by enter 3 For units lacking a front panel jog shuttle the 15 F3 and 16 F4 ASCII front panel equivalent can be used 44 CHAP 7 Specifications CHAP 7 Specifications The best picture quality in Playback JPEG 2000 Real time live display in all channels 4 channel video 240 200 ips recording capability e Triplex Playback Recording Ethernet Multi language menu 2 COO EO CO CO Cs O 2O COD CO CO OCDE e Remote monitoring and download through network Convenient search function with Jog shuttle e VGA option available Supporting TFT LCD Monitor USB Device port for firmware upgrade Easy PTZ camera control by pre assigned buttons e Password Protection e Remote Controller Multiplex function Storage Internal HDD Capacity CD RW Video Inputs Composite Outputs Composite VGA Loop out Compression Compression Rate Image size fixed Display Speed Recording Recording Mode Search Search Recording Speed NTSC PAL Recording Resolution NTSC PAL Multi language Switching Interval Live Division Screen Alarm Inputs Outputs Post Alarm Motion Detection Network Backup PTZ Control Firmware upgrade Serial F RS 485 RS 232C Inp
41. r can see saved images using Windows Media Player Calendar Use this to select the date you wish to search The filled in square outlines the date that is at the beginning of the hard drives The outlined square indicates the data at the end of the hard drives Select the date you wish to view Verify a filled in square for that particular date If an invalid date is selected it will default to the beginning of the hard drive s 40 CHAP 6 Back up CD Player 6 3 Back up CD Player NO IMAGE DVR units are with a built in CD RW and user can copy images to CD Using back up CD player user can see images on back up CD and function of each button in Back up CD player is as below 1 Time Current time 2 Status Window Start amp End of time amp date Status of operating button When user play forward backward recorded time will appear 3 Play Speed button User can adjust play speed by pressing up down button Speed 1 4X 1 2X 1X 2X 4X 8X 16X Delay 1 2 4 8 16 32 4 Operation button User can search recorded data using these buttons a Move the slide bar to start position c Play backward at 1x speed d Pause e Play forward at 1x speed f Play fast forward in preset speed g Move the slide bar to end position 5 Function button a OPEN Open the Back up CD Player b EDIT User can edit save and print recorded image on Edit mode This edit button will work when you selected one of 16 came
42. ras c EXIT Exit from Back up CD Player 6 Channel button Select channel to see pictures in full screen 7 Slide Bar Move to a point from which user want to see Page button This button is just working when screen division is 4 split in 8 ch DVR or 4 split or 8 split in 16 ch DVR Moves to next page 9 Screen division 1 4 9 16 41 CHAP 6 Back up CD Player 0 When you open the file audio menu OSD will come up automatically on check to output recorded sound then choose the audio channel 1 2 3 or 4 skip skip images forward 3 During playback you can control During playback only one channel is displayed and can not be changed to multi or full screen Image EDIT DATE 2005 06 20 TIME 14 23 54 WIDTH 720 pixel HEIGHT 480 pixel Brightness Save Print Exit a 2005 06 208131 23 54 1 Image Edit Status Window Shows record time amp date Image size Command status 2 Edit Button User can adjust color tone of copied images using this button Contrast make bright part of image brighter and dark part of image darker b To reduce light and shade lower contrast a little Brightness a make an image brighter b make an image darker Sharpness give sharp edge effect Blur make an image soft 3 Function button Save User can save an image in JPEG format It is saved in the folder where you installed back up CD player b Print
43. ront panel of DVR Refer to START and END of data on HDD and set start and end time of data to USB Media Memory Stick or USB HDD Select backup file size and move to BACKUP and press ENTER Button to start copy 28 Status message CHAP 5 Set Up USB HDD control only Partition can be selectable by Ch button 1 4 HDD START 2005 AUG 07 AM04 04 12 END 2005 AUG 08 PM08 12 23 USB MEDIA START 2005 AUG 07 AM04 04 12 END 2005 AUG 08 PM08 12 23 SIZE 00000MB BACKUP USB STORAGE IS CHECKING EXIT MENU System Status Messages 1 If MEMORY STICK is not inserted USB STORAGE IS CHECKING USB STORAGE IS NOT AVAILABLE RE CONNECT THE USB STORAGE CONECT THE OTHER USB STORAGE 2 When MEMORY STICK or USB HDD is recognized USB STORAGE IS CHECKING THERE IS A FREE SPACE ON STORAGE USB STORAGE IS AVAILABLE 3 During Back Up HDD START 2005 AUG 07 AM04 04 12 END 2005 AUG 08 PM08 12 USB MEDIA 118M 28 START 2005720G 07 AM04 94 END 2005 AUG 08 PMO08 12 2 SIZE 28 MB gt 28MB BACKUP C START WRITING IN USB STORAGE EXIT MENU SIZE FREE SPACE PARTITION CHANGE WRITE PROTECT MODE Only WRITE PROTECT is caught it can be seen START WRITING IN USB STORAGE FINISH WRITING IN USB STORAGE 4 Error Message THERE IS A PROBLEM ON USB PORT If USB PORT fails to work properly USB STORAGE IS FULL When USB is full FILE SY
44. ssword as per the procedure in SYSTEM MENU CONFIGURATION PASSWORD SETUP x For security reasons be sure to make note of your own password 4 2 Factory Default Before first operation you must set Time Date set FACTORY DEFAULT and then clear HDD even though it is brand new one It is to make DVMR system and HDD ready for proper operation Starting recording without FACTORY DEFAULT setting and HDD clear will cause malfunction 1 HDD CLEAR 2 FACTORY DEFAULT HDD MANAGEMENT DISPLAY SETUP TIME DATE SETUP DISPLAY SETUP CONFIGURATION CAMERA SETUP CONFIGURATION REOCRD SETUP INTERVAL SETUP REOCRD SETUP BACK UP ALARM SETUP BACK UP EXTERNAL DEVICE EVENT POPUP SETUP EXTERNAL DEVICE FACTORY DEFAULT BUZZER SETUP FACTORY DEFAULT LANGUAGE PASSWORD SETUP LANGUAGE SYSTEM IMFORMATION Refer to page 22 Refer to page 31 13 CHAP 4 Operation 4 3 Display Configuration HDD Status In live mode Amount of data recorded In Playback mode Amount of data played ETHERNET status Connected Disconnected Status of DVR system Emergency Record Red Schedule Record Green Record Stop White Stop Forward Playback Backward Playback Pause 1 16 1 2x forward playback 1 16 1 2x backward playback 2 4x forward playback 2 4x backward playback 16 64x forward playback 16 64x backward playback i ALARM Record LJ
45. tton to set ON Highlighted Area Motion Detection Area Non highlighted Area No Motion Detection Area 23 CHAP 5 Set Up 4 INTERVAL SETUP SWICHING INTERVAL FULL SCREEN 01 SEC Set the switching time interval for SEQ or PIP PIP SCREEN 01 SEC function 1 sec 99 sec EVENT RECORD 1 FULL SCREEN set the sequencing switch time interval EVENT UPDATE TIME 01 SEC in live full screen 2 PIP SCREEN set the sequencing switch time interval of PIP window SELECT A Y 4 gt CHANGE VALUE 3 EVENT UPDATE TIME Set the minimum time interval of event to be listed in EVENT LIST If EVENT UPDATE TIME is set at 20 sec only following event happened 20 sec or more than 20 sec later previous event shall be listed in EVENT LIST 5 ALARM SETUP Set type of alarm sensors connected to DVR unit CHANNEL CH1 N O represents Normal Open type and N C Normal ALARM INPUT N O Close type DURATION 005 1 ALARM INPUT Select type of alarm sensor connected to DVR unit N O or N C Use direction button and button NO aaa NORMAL OPEN to set Nus ee ee NORMAL CLOSE DISABLE represents not to use alarm eR DISABLE sensor connected to DVR 2 DURATION Set the duration of alarm when an SELECT A Y CHANGE VALUE alarm is activated 0 sec 300 sec 6 EVENT POPUP SETUP When
46. ut AUDIO Output Power Requirements Weight Triplex Playback Recording Ethernet Up to 2 HDDs with no limitation in capacity For Backup 8Ch 2Ch Monitor SPOT 1Ch Supporting TFT LCD Monitor Option 8Ch JPEG 2000 Basic Normal Enhanced Fine Super Fine Real Time display Schedule Time Motion Alarm Emergency Event Search Date Time Search Search Bar Jog Shuttle Full 120 100 Dual 240 200 Quad 480 400 Full 720x240 720x288 Dual 360x240 360x288 Quad 360x120 360x1 44 English Spanish German French Italy Russian Dutch Polish Portuguese etc 1 99 sec selectable 1 4 9 Split Digital Zoom Freeze PIP SEQ Event Popup 4 Alarms NO NC selectable in SETUP menu 1 NO NC Duration of alarm output 1 sec 300 sec selectable Area division 16 x12 Detection Division 32 x 24 Ethernet TCP IP Remote viewer program included VCR CD RW back up Download via IP Network RS 485 Key Control Key assigned for each PTZ command USB port for firmware upgrade CD R For PTZ camera control For operation using keyboard of PC 4CH Microphone Input 1CH Speaker Output DC 12V 6 67A Adaptor 8 5kg Dimensions WXHXD mm 436 X 396 X 88 Packing 600 X 520 X 180 Design and specifications are subjected to changes without notice 45 46 FC CC c 8Channel Stand Alone DVR Audio USB Backup available Best Picture Quality JPEG2000
Download Pdf Manuals
Related Search