User manual ArcSource Outdoor 48 MC Integra_Smart_white
Contents
1. 265 20 ArcSource Outdoor 48 MC Integral SmartWhite Tilt adjustment range e 90 Weight 10 8 kg Protection factor e P 67 Impact resistance e K 06 Connection e Data power cable Li9Y11Y 3xAWG16 2xAVG24 shielded and jacketed e junction box e connection between LED unit and control unit Igus CF9 03 08 with connectors 1x Chogori O8BMMA SL8001 male at LED unit and 1 x CGRBDU O8BFFA female at Control unit Note In the case that the control unit is is installed separately max length of connection cable between the control unit and the LED unit should not exceed 20 metres Included items e 1 x ArcSource Outdoor 48 MC Integral e 1 x Junction box e 1 x User manual Optional Accessories e Top Hat ArcSource Outdoor 48 MC No 10980173 e Half Top Hat ArcSource Outdoor 48 MC No 10980174 e Stand for ArcSource Outdoor 48 MC No 1098 0176 9 Cleaning and maintenance DANGER Disconnect from the mains before starting any cleaning or maintenance work Rinse off loose dirt with low pressure water spray Wash the housing with a soft brush or sponge and a mild non abrasive washing detergent Rinse it There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by a qualified person Should you need any spare parts please use genuine parts Specifications are subject to change without notice October 29 2013 212. 6 3 Personality Use this menu to modify the ArcSource Outdoor 48 MC Integral operating behaviour DMX Pres DMX preset Select this menu item to set a desired DMX mode Please refer to the chapter DMX protocol for detail description of each DMX mode DMX In DMX input Use the menu to select mode of receiving DMX signal Wired DMX signal is received by means of the standard DMX cable Wireless DMX signal is received by means of the inbuilt wireless module wireless DMX version only M FTime Max Fade time Select this menu item to set a desired max fade time 0 25 5 sec This adjusted fade time influences fade of Red Green Blue White and dimmer during DMX operation If time between two receiving DMX values is gt than fade time set in the item M Ftime the entire adjusted fade time will be used If time between two receiving DMX values is lt than fade time set in the item M Ftime the adjusted fade time will be reduced to fill entire time between the two receiving DMX values e g M Ftime 2sec and fixture has received Red 0 DMX after 5 seconds will receive Red 255 DMX It means that red will go to full intensity during 2 seconds M Ftime 8 sec and fixture has received Red 0 DMX after 5 seconds will receive Red 255 DMX It means that red will go to full intensity during 5 seconds Max fade time is reduced from 8 sec to 5 sec Display Display adjusting This function allows you to
3. change the display settings Turn This function turns the display by 180 13 ArcSource Outdoor 48 MC Integral SmartWhite On Off T This function allows you to keep the display permanent on or turn it off two minutes after last pressing any button on the control panel Contrast Use this function to adjust contrast of the display 0 100 Backlight Use this function to adjust backlight of the display 0 100 Temp U Temperature Unit Use this menu in order to display the fixture temperatures in desired units C or F Init Pos Init effect positions Use this function to set all effects to the desired positions to which they will move after switching the fixture on if DMX is not being received Defaults Default Settings The menu item sets all fixture parameters to the default factory values 6 4 Manual mode Use this menu for control the fixture without connected DMX console To control fixture channels 1 Use the UP DOWN buttons to find Manual menu 2 Press the ENTER button 3 Use the UP DOWN buttons to select desired effect channel List of control channels Strobe a strobe shutter Dimmer a dimmer Dimmer F a fine dimmer 4 Press the ENTER button and use the UP DOWN buttons to set value press the ENTER button to confirm it 6 5 Test sequences Use this menu to run demo test sequences without an external controller which will show you some possibilities of using th
4. device and consult installation with an expert Warning for wireless DMX version The antenna must be instaled on the fixture to keep declared IP rating of the fixture There is a possibility to install the LED unit and the control unit separately Four holes with diameter of 5 3mm in the control unit are intended for mounting on a flat non flammable surface The length of the connection cable between the control unit and the LED unit should not exceed 20 m 3 2 Top hat Half top hat installlation Top hat Half top hat 1 Unscrew the four socket heads 6x10 1 in the ArcSource Outdoor 48 MC housing and slide the top hat 2 onto ArcSource outdoor 48 MC Integral 2 Secure it with four socket heads 6x10 through holes 3 in the top head ArcSource Outdoor 48 MC Integral SmartWhite 3 3 Connection to the mains Fixtures must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulation The ArcSource Outdoor 48 MC Integral is equiped with with a 5 cored power data cable The 3 cores serve for the power supply and next 2 shielded cores are intended for DMX connection The power cores are coloured according to the following table This device falls under class one and must be grounded The data cores DMX are coloured according to the table Core Connection ee Shielding Data ground The power data cable is connected to a junction box as shown on
5. during 5 seconds and after that they will stay in this position for 15 seconds before going to the next prog step 1 1 Use the UP DOWN buttons to find Sta Alone menu and press the ENTER button 2 Use the UP DOWN buttons to select Pr Edit menu and press the ENTER button 3 Use the UP DOWN buttons to select a program you want to edit Prog 1 Prog 3 and press ENTER button 4 Use the UP DOWN buttons to select a desired program step Step 01 Step 40 and press ENTER button 5 Use the UP DOWN buttons to select a channel you want to edit and press the ENTER button List of editable items Prg En a total number of program steps value 1 40 This value should be set before start programming e g if you want to create program with 10 steps set Prg En 10 Warm W warm white LEDs saturation Cool W cool white LEDs saturation C Wheel a virtual colour wheel Strobe a strobe shutter Dimmer a dimmer Dimmer F a fine dimmer F tim a fade time 0 25 5 seconds S tim step time value 0 25 5 seconds COPY this item duplicates the current prog step to the next prog step The item Prg En is increased automatically 6 Use the UP DOWN buttons to set a DMX value of the channel and then press the ENTER button Use the UP DOWN buttons to select next channel and press the ENTER button 8 After having set all channels in the current program step press the MO
6. lack qualification do not attempt the update yourself and ask for help your Anolis distributor Note 2 DMX address programs and all items in the menu PErS will be set to their default values To update software in the fixture I Installation of the DMX Software Uploader 1 DMX Software Uploader program is available from the Anolis web site at WWW anolis cz 2 Make a new directory e g Anolis Uploader on your hard disk and download the software into it 3 Unpack the program from the archive Il Fixture software updating 1 Determine which of your port is available on your PC and connect it with the DMX input of the fixture if you using the flash cable RS232 DMX with the DMX input of the Robe Universal Interface if you using the USB cable Disconnect the fixture from the other fixtures in a DMX chain Turn both the computer and the fixture on Make sure the lamp is switched off only if the fixture involves a lamp 2 Switch the fixture to the updating mode 1 Use the UP DOWN buttons to find SPEC menu Press the ENTER button Use the UP DOWN buttons to select uPd item Press the ENTER button Use the UP DOWN buttons to select yES option Press the ENTER button Note If you do not want to continue in software update you have to switch off and on the fixture to escape from this menu 3 We recommend to cancel all running programs before start of the Software Uploader 4 Run the Software Uploader program Se
7. ArcSource Outdoor 48 MC Integral SmartW ArcSource Outdoor 48 MC Integral Smart W Wireless DMX USER MANUAL ArcSource Outdoor 48 MC Integral SmartWhite Table of contents a LUCHO Ss si cd a E A 3 2e FIXUS exterior VIEW saias aha ont RS O nas SG nada Oi O eae Ne et eset a E 5 Su INSANA O iii ans il EA A A A DU pe DR 5 Sl MIO UME SES el gE 5 32 Jopihai Half top hat installato 6 3 3 CONNECTION to Lhe Mains snee RITO ies 7 ArcSource Outdoor 48 MC Integral SmartWhite DMX protocol co ooooccccncnconoccnnnnnonanonnnonanocnnnnnnnncnnnnnonanocncnnnonaninos 9 De ernie MMO NIC A rara Dna tance ousados Maisa asa atari 10 FIXUS na EN 12 SALERNO dd a RR del 12 6 2 PENALES INTO MAT ON aa aia 12 53 Personalidad O RR O A MS PR 13 Og Manual moden na cris ora 14 Bro Test SEQUENCES usei a anda Cod tea caus Beene aa 14 GO tandsalone oy is o a eee 14 6 3 peclal TUNG TIONS eneen A DD O eens 15 TBD INN nti ts beeren eenen nende ehehe antes 17 On Kle MINICAl SEC onz il og CEN 18 9 clean ineiana mantente aida 21 ArcSource Outdoor 48 MC Integral SmartWhite FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR ArcSource Outdoor 48 MC Integral Save it for future reference This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning no
8. DE button to go by one menu level back and select another program step A 6 7 Special functions rdM Low RDM Code This menu item shows the first part of the RDM identification code rdM High RDM Code This menu item shows the second part of the RDM identification code Wireless Wireless state This menu serves for reading of the state of wireless operation only Wireless DMX Unlink The item serves for unlinking the fixture from the transmitter only Wireless DMX version IniBlink Initial blink If this function is on the fixture makes auto calibration each LED colour lit on 100 for short time after switching the fixture on Hold DMX If the function is on the last received DMX values are held in case that DMX data receiving was interrupted e g disconnected DMX controller 15 ArcSource Outdoor 48 MC Integral SmartWhite Flicker Free Mode If the function is on the light flickering visible in cameras is corrected but colour uniformity is worse SW Upd Software update The menu item allows you to update software in the fixture via either serial or USB port of PC The following are required in order to update software PC running Windows 95 98 2000 XP 7 8 or Linux DMX Software Uploader Flash cable RS232 DMX No 13050624 if you want to use a serial port of PC Robe Universal Interface if you want to use an USB port of PC Note1 Software update should execute a qualified person If you
9. e ArcSource Outdoor 48 MC Integral 6 6 Stand alone setting Sta Alone The fixtures on a data link are not connected to the controller but can execute pre set programs which can be different for every fixture Auto Run Automatic playback This function allows you to select the program which will be played after switching the fixture on Selected program will be played continuously in a loop 1 Use the UP DOWN buttons to find Sta Alone menu Press the ENTER button Use the UP DOWN buttons to select Auto Run item Press the ENTER button Use the UP DOWN buttons to select desired program Press the ENTER button to confirm the choice OY ee Pr Play Playing program By enter to this menu a complete overview of all programs is offered from which the program to be run can be selected 1 Use the UP DOWN buttons to find Pr Play menu 2 Press the ENTER button 14 ArcSource Outdoor 48 MC Integral SmartWhite 3 Use the UP DOWN buttons to select desired program 4 Press the ENTER button The selected program runs in a loop Pr Edit Editing a program The fixture offers 3 freely editable programs Prog 1 Prog 3 each up to 40 steps Every program step includes a fade time the time taken by the step s channel status to reach the desired level and a step time the total time occupied by the step in the program E g If F tim 5 second and S tim 20 second effects will go to the desired position
10. eration hours of the fixture Total the function shows the total number of the operation hours since the ArcSource Outdoor 48 MIC Integral has been fabricated Reset the function shows the number of the operation hours that the ArcSource Outdoor 48 MC Integral has been powered on since the counter was last reset In order to reset this counter to O you have to press and hold the UP and DOWN buttons and at the at the same time press the ENTER button DM In DMX values Select this function to read DMX values of each channel received by the fixture Temp Fixture Temperatures Select this menu to read the temperatures of the fixture Current the current temperature of the fixture inside Highest the menu item shows the max temperatures of the fixture inside since the ArcSource Outdoor 48 MC Integral has been fabricated High Res the menu item shows the maximum temperatures of the fixture inside since the counter was last reset In order to reset this counter to O you have to press and hold the UP and DOWN buttons and at the at the same time press the ENTER button Measuring points Led temperature on the PCB with LEDs Board temperature on the control board of LEDs Note The ambient temperature should not exceed 40 C The temperatures can be displayed in either C or F units see option tEM U in the menu Pers Sw Ver Software Versions Select this function to read the software version of the fixture processors
11. esult of unprofessional operation Do not attempt to dismantle or modify the unit Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons Please use the original packaging if the fixture is to be transported If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock etc ArcSource Outdoor 48 MC Integral SmartWhite 2 Fixture exterior view LED unit Control unit Antenna only wireless DMX version Tilt adjusting locks U bracket Control board with anti vandal cover Power Data cable LED unit connecting cable 3 Installation 3 1 Mounting the fixture The ArcSource Outdoor 48 MC Integral can be arranged in any position orientation The LED module can be tilted to desired position by means of the tilt lock Use an Allen key 6 to adjust desired position 0 90 ArcSource Outdoor 48 MC Integral SmartWhite Three slots in the fixture U holder serve for mounting on the non flammable flat surface Ensure that the structure to which you are attaching the fixture is secure Caution Overhead installation requires experience Fixtures may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do not install the
12. he fixture s LEDs during operation The intense light beam may damage your eyes Keep compustible materials at least 20 cm away from the fixture If the fixture has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Avoid brute force when installing or operating the fixture ArcSource Outdoor 48 MC Integral SmartWhite The fixture was designed for outdoor use This fixture must not be used for underwater installation When choosing the installation spot please make sure that the fixture is not exposed to extreme heat or dust Avoid using the unit in locations subject to possible impacts The fixture body never must be covered with cloth or other materials Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Do not block the front objective LEDs with any object when the fixture is under operation The fixture becomes very hot during operation Allow the fixture to cool approximately 30 minutes prior to manipulate with it Operate the fixture only after having familiarized with its functions Do not permit operation by persons not qualified for operating the fixture Most damages are the r
13. ion of 10 Optic amp Effects e Light source 12 x 10W SW multi chip LEDs e Available optical systems Spot Medium Flood e RGBW colour mixing e Built in colour macros e Adjustable strobe sequences e White colour balance adjusting e typical Lumen maintenance 70 60 000 hours Control e Protocol USITT DMX 512 RDM e DMX modes 3 2 2 or 6 control channels e Operation modes DMX Stand alone e Setting and addressing Two row LCD display amp control buttons or via RDM Wireless DMX RDM module for wireless DMX version only e Compliance with USITT DMX 512 1986 amp 1990 and 512 A e Full DMX fidelity and frame integrity e Auto sensing of DMX frame rate and frame size e lt 5ms DMX latency e Operational frequency range of 2402 2480 MHz e Producer LumenRadio Antenna for wireless DMX version only e Max gain 5dBi Strobe e Strobe effect with variable speed max 20 flashes per second e Pre programmed random strobe pulse effects Dimmer e Smooth 16 bit dimming from O 100 Rigging e Via two slots in the fixture base 18 ArcSource Outdoor 48 MC Integral SmartWhite Temperatures e Maximum ambient temperature 40 C e Maximum housing temperature 80 C Total heat dissipation e 443 BTU h calculated Dimensions mm ArcSource Outdoor 48 MC Integral set EE 19 ArcSource Outdoor 48 MC Integral SmartWhite Junction box 147 138 3 Top hat
14. lect desired COM and then click on the Connect button DUB 0 NN File Info Box Select COM if the ANOLIS O Clear Box serial port is used oN COM Ports f COM 1 COME COM Select DreamBox1 C com 4 if the USB port is E used Connect pa Status Disconecked W Incremental Update Ea 16 ArcSource Outdoor 48 MC Integral SmartWhite If the connection is OK click on the Start Uploading button to start uploading It will take several minutes to perform software update If the option Incremental Update is not checked all processors will be updated including processors with the same software version If you wish to update only later versions of processors check the Incremental Update box Avoid interrupting the process Update status is being displayed in the Info Box window When the update is finished the line with the text The fixture is successfully updated will appear in this window and the fixture will reset with the new software Note In the case of an interruption of the upload process e g power cut the fixture keeps the updating mode and you have to repeat the software update again For example The fixture was switched off before finishing software upload After switching again the fixture on the fixture is still in the updating mode and the display is dark Restart the Software Uploader program and repeat software update from your PC 7 RDM This fixture is ready for RDM operation RDM Re
15. mote Device Management is a bi directional communications protocol for use in DMX512 control systems it is the new open standard for DMX512 device configuration and Status monitoring The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non RDM equipment By using a special Start Code and by complying with the timing specifications for DMX512 the RDM protocol allows a console or dedicated RDM controller to send commands to and receive messages from specific moving lights RDM allows explicit commands to be sent to a device and responses to be received from it The list of commands for ArcSource Outdoor 48 MC Integral is the following Parameter ID SET command GET command DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO SUPPORTED PARAMETERS SOFTWARE_VERSION_ LABEL DMX START ADDRESS IDENTIFY DEVICE DEVICE MODEL DESCRIPTION MANUFACTURER LABEL DEVICE LABEL SENSOR DEFINITION SENSOR VALUE DISPLAY LEVEL DEVICE RESET ArcSource Outdoor 48 MC Integral SmartWhite DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION STATUS MESSAGES STATUS_ID_DESCRIPTION DEVICE HOURS Please see the Robe Universal Interface user manual for detail description of RDM operation 8 Technical specifications Power supply e Electronic auto ranging e Input voltage 100 240V AC 50 60 Hz e Power consumption 130W 230W power factor 0 93 0 55A Allow for a deviat
16. tes written in this manual The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty 1 Safety instructions DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT Make sure that the available voltage is not higher than stated on the rear panel of the fixture This fixture should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied consult your authorized distributor or local power company Always disconnect the fixture from AC power before cleaning removing or installing the fuses or any part Do not overload wall outlets and extension cords as this can result in fire or electric shock Make sure that the power cord is never crimped or damaged by sharp edges Check the fixture and the power cord from time to time Do not install the unit near naked flames During the operation the housing becomes hot up to 80 C Refer servicing to qualified service personnel This fixture falls under protection class Therefore this fixture has to be connected to a mains socket outlet with a protective earthing connection Do not connect this fixture to a dimmer pack LED light emission Risk of eye injury Do not look straight at t
17. the picture below Screws Fixture Screws Junction box zZ Power Signal x L Live Signal O N Neutral GND Signal ground Earth ArcSource Outdoor 48 MC Integral SmartWhite Gan RO Power cable The junction box allows to connect several fixtures in a daisy chain of the power data cable Use the 3 x 1 5mm power cable to connect the first junction box with the mains and the power data cable for connecting fixtures each other Do not overload the supply line and the connecting leads The max number of connected fixtures in a daisy chain depends on the input voltage 14 fixtures at power supply 230V for power cable 3 x 1 5mm 7 fixtures at power supply 120V for power cable 3 x 1 5mm You have to take into account the the length of power data cable circuit breaker etc at projecting of the fixtures installation ArcSource Outdoor 48 MC Integral SmartWhite ArcSource Outdoor 48 MC Integral SmartWhite DMX protocol Version 1 0 Mode Channel Value Type of control a papa 1 1 Warm white LEDs 0 255 Warm white LEDs saturation control 0 100 proportional 2 2 Cool white LEDs 0 255 Cool white LEDs saturation control 0 100 proportional 1 3 Colour wheel 0 No function 1 2 White 2800 K step 3 4 White 3200 K step 5 6 White 3800 K step 7 8 White 4200 K step 9 10 White 4600 K step 11 12 White 5000 K step 13 14 White 5600 K Step 15 16 White 6300 K step 17 247 Warm white gt Cool
18. to set the fixture according to your needs obtain information on its operation and manual control of all effects The four control buttons on the front have the following functions ESCAPE button leaves menu without saving changes lt l ENTER button enters menu confirms adjusted values and leaves menu A UP and V DOWN buttons move between menu items on the same level sets values 6 1 Fixture Address DMXA 0001 Use this menu to set the DMX address of the fixture Set DMXA Set DMX address Select this submenu to set a DMX start address To set a DMX address 1 Use the UP DOWN buttons to find DMXA 0001 menu 2 Press the ENTER button 3 Use the UP DOWN buttons to select desired start address 4 Press the ENTER button to confirm the choice Note After switching on the ArcSource Outdoor 48 MC Integral will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the display will start to flash with actually set address 6 2 Fixture information Use this menu to read useful information about the fixture status To display desired information 1 Use the UP DOWN buttons to find the InFo menu 2 Press the ENTER button 3 Use the UP DOWN buttons to select the required menu item 4 Press the ENTER button to confirm the choice 12 ArcSource Outdoor 48 MC Integral SmartWhite Pon Time Power On Time Use the menu item to read the number of op
19. white proportional 248 Rainbow effect with fade time step 249 Rainbow effect step 250 255 Reserved Strobe 0 31 Shutter closed step 32 63 Shutter open step 64 95 Strobe effect from slow to fast proportional 96 127 Shutter open step 128 143 Opening pulses in sequences slow gt fast proportional 144 159 Closing pulses in sequences fast gt slow proportional 160 191 Shutter open step 192 223 Random strobe effects from slow to fast proportional 224 255 Shutter open step 2 5 Dimmer O 255 Dimmer intensity from 0 to 100 proportional Dimmer fine O 255 Fine dimmer intensity from low to high proportional ArcSource Outdoor 48 MC Integral SmartWhite 5 Control menu map Default settings Bold print Menu Level 1 Menu Level 2 Menu Level 3 Menu Level 4 Menu Level 5 Menu Level 6 DMXA 0001 0512 0001 Do MN A o A po A po o rm current ue po fort poo poo FR RR O CO RR RR FR RR CT IESO nes ee RR po po fra poo poo vero asp poo po ap po o o OOOO IESO RR IESO E E pers fomxrres Moa o rap poo sp poo o n fwe Wireless Backlight 0 100 10 ArcSource Outdoor 48 MC Integral SmartWhite Menu Level 1 Menu Level 2 Menu Level 3 Menu Level 4 Menu Level 5 Menu Level 6 tempus Per o Defaults E o o CS o ArcSource Outdoor 48 MC Integral SmartWhite Menu Level 1 special CE o YO maen O O O e CE see RR RR quim po yoo poo Flicker free On Off Mode 6 Fixture menu The control panel menu allows
Download Pdf Manuals
Related Search