Home

Manuals

1. Memory 5 port 512K bits 8 port 768K bits Power Supply External Power adapter 0 6A 5VDC Power Consumption 3W Max Dimensions 5 port 121mm W x 74 2mm D x 26mm H 4 76 W x 2 92 D x 1 02 H 8 port 159mm W x 85mm D x 26mm H 6 25 W x 3 55 D x 1 02 H Weight 5 port 245g 0 54lb 8 port 335g 0 74lb Operating Temperature OC to 45 C 32 F to 113 F Storage Temperature 10 C to 70 C 14 F to 158 F Humidity 5 to 95 non condensing Emission Compliance CE Mark Class B FCC Part 15 Class B and VCCI Class B 5 8 Port 10 100Mbps Ethernet Mini Switch FCC Certifications C This Equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this
2. 5 8 Port 10 100Mbps Ethernet Mini Switch Introduction The device is a powerful high performance Fast Ethernet switch with all ports capable of 10 or 100Mbps auto negotiation operation NWay which means the switch could automatically negotiate with the connected partners on the network speed and duplex mode It is ideal for micro segmenting large networks into smaller connected subnets for improved performance enabling the bandwidth demanding multimedia and imaging applications Compared to the shared 10Mbps or 100Mbps networks the switch delivers a dedicated 10 100Mbps connection to every attached client with no bandwidth congestion issue This switch also supports auto MDI MDI X function Each port could be used to connect to another switch or hub with no crossover Ru 45 cable Store and forward switching mode promises the low latency plus eliminates all the network errors including runt and CRC error packets To work under full duplex mode transmission and reception of the frames can occur simultaneously without causing collisions as well as double the network bandwidth The switch is plug n play without any software to configure and also fully compliant with all kinds of network protocols Moreover the rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system Before you start to install the switch check the following contents in this package e One NWay switch o One external po
3. device must accept any interference received including interference that may cause undesired operation CE Mark Warning C This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class B for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2005 All Rights Reserved
4. wer adapter e User s manual LED Definition Please refer to the following table for LED definition Sport i Sport Power Steady Green Power is on Off Power is off Link Act Steady Green The port is connected Blinking Green The port is transmitting receiving data Off No connection Rear Panel 5 8 Port 10 100Mbps Ethernet Mini Switch Stations Connection Connect each station to the switch by twisted pair cable Plug one RJ 45 connector into a RJ 45 port of the switch and plug the other RJ 45 connector into the station s network adapter Power on the switch and then system is ready For cable selection refer to the following table Switches Connection In making a switch interconnection you could use any port to connect another switch with straight or crossover cable As all the ports support auto MDI MDI X function using a straight cable to make a switch to switch connection is allowed For cable selection refer to the following table 10Mbps Cat 3 4 5 UTP STP 100 meters 100Mbps Cat 5 UTP STP 100 meters Standard IEEE 802 3 10Base T IEEE 802 3u 100Base TX IEEE 802 3x full duplex operation and flow control Interface 5 10 100Mbps RJ 45 Fast Ethernet Ports 8 10 100Mbps RJ 45 Fast Ethernet Ports Uplink Auto MDI MDI X Auto crossover Network Speed 10 100Mbps amp Full Half duplex mode auto detection MAC Address Table 1024 MAC address entries

Manuals

Contents

Download Pdf Manuals

Related Search

Related Contents