Full Motion TV Wall Bracket For Curved or Flat Screens
Contents
1. LST j f IN j Magnetic Spirit ia o U Leveler Stud Finder P n 3 16 5mm Step 2 Assemble the TV bracket with 4 x M8 12mm bolts as show below The spacing of the bars will depend on the VESA hole spacing on the back of your screen They can be positioned at VESA 200 300 or 400 After the bracket is assembled fix it on the back of the screen as show below Square Front Cover O Washer A6 TV Bracket Plastic a o Ve Vertical Piece Spacer A5 fp Screen Fixing Screw A1 A2 A3 A4 M8 12mm Bolt Square Washer For M8 Screws For M5 6 Screws For M4 Screws Step 3 Install TV on to the wall bracket 1 Screw on the M8 nuts on to the on the back before slotting the screen on this prevents the screen from falling off whilst installing 2 Slot the screen and fixed bracket onto the wall bracket 3 Tighten the bottom M8 nut once the screen is level 4 Adjust the tension of the tilt mechanism until desired angle is achieved 129 561UK User Manual av link Step 4 Pan and swivel tension adjustment There is a hex bolt on each of the arm joints where the movement tension can be adjusted using the supplied Allen Key Loosen each bolt to move the screen into desired place Tighten the bolts to lock the screen in position Step 5 Cable management system Unclip the plastic covers on the bracket arms Run the cables a2. av link CC601 Full Motion TV Wall Bracket For Curved or Flat Screens Item ref 129 561UK User Manual Thank you for choosing the CC601 TV bracket This bracket is constructed from reinforced steel to allow a screen sized from 32 to 65 and up to 45kg to be mounted on a wall safely Designed to be easily installed and supplied with all required installation hardware Caution Please read this manual thoroughly to avoid damage to property or personnel If unsure of any part of this manual please refer to professional installer for help e This product contains small components that could pose a choking hazard if swallowed please keep out of reach of children e This product is designed for mounting on wall studs or concrete wall Always ensure the mounting surface will be capable of withstanding the combined weight of the TV bracket and TV reinforcement may be required for aged or weak walls e Safety gear such as gloves and safety goggles must be worn during the installation A minimum of two people are required throughout the installation failure to do so may result in injury or damage e This product is design for indoor use only The bracket must be inspected at least every two months for loose joints or aged parts Contents Please check all contents listed below are included inside the box If anything is missing please return to the retailer or dealer Wall Bracket Cover i a x qa M5 25mm x 4 A2 M6 25mm x 4 A3 mm x
3. TV Bracket a sia Plastic Spacer x 4 A5 M8 Washer s Square Washer x 4 A6 se F Wall Mounting Screw x 6 B1 a ji va Wall Plug x 6 B2 Washer x 6 B3 e Magnetic Spirit Level Wall Bracket dikigi A L Allen Key Ny M6 M8 Wrench M8 12mm Bolt uae Cover For this installation you will also require a pencil tape measure electric drill stud finder and a Philips cross screw driver Step 1 Fixing wall bracket For concrete wall installation first of all work out the height of the installation and ensure it is level using the spirit level Use a pencil to mark where the mounting holes will be and use an electric drill to drill a hole that is around 10mm in diameter and 60mm deep Insert the wall plugs into the holes and install the wall bracket as follows Concrete Wall Wall Plug B2 Ng Washer B3 _ gt 7 Wall Mounting tt S O a Screw B1 Ja i Magnetic Spirit 60mm weer J 3 8 10mm avilink awsl com ar ons Group brand av link For plaster wall installation first of all find out where the wood stud is behind the wall using a stud finder Then work out the height of the installation and ensure it is level using the spirit level Use a pencil to mark where the mounting holes will be and use an electric drill to drill a hole that is around 5mm in diameter and 60mm deep Install the wall bracket as follows Wood Stud Washer B3 Wall Mounting Screw B1
4. long the arm as shown below and clip the plastic covers back on This will stop cables from tangling and getting caught in the brackets joints Errors and omissions excepted Copyright 2015 AVSL Group Ltd 129 561UK User Manual
Download Pdf Manuals
Related Search