Home

DVG-N5402GF User`s Manual - D-Link

1. VLAN is optional It works with the Router or Switch that supports VLAN tag By adding VLAN tag in packets may improve efficiency of voice traffic performance and security Enable VLAN Tagging It is to tag the packets for VLAN Router or Switch identifying VLAN ID It is to assign uniquely a user defined ID to each packet Priority It is the proprietary to VLAN Router or Switch Note Please do not change anything here unless requested by your ISP D Link Systems Inc 21 DVG N5402GF User s Manual SETUP 3 1 2 VoIP Setup In this section it supports registration to multiple Proxy Servers which is allowed to choose ITSP by user manually If any registration problem occurs please consult your VoIP Service Provider SETUP VoIP Setup Clink Edit icon to modify the settings The same configurations and applications apply to three Proxy Servers Select one of three Proxy Servers for SIP configuration The device can set up multiple SIP proxy servers For load balancing on the same ITSP to get the better response and high availability PROXY SERVER Proxy Status ITSP Name Proxy Server IP Proxy Server Port Disable 192 168 1 1 5060 E Disable 192 168 1 1 5060 E Disable 192 168 1 1 5060 D Link Systems Inc 22 DVG N5402GF User s Manual SETUP SETUP VoIP Setup C Enable Support of SIP Proxy Server Soft Switch ITSP Name Enable Support of SIP Proxy Server Soft Switch Check the box
2. Do Not Disturb Check the box to reject busy tone played incoming calls Unconditional Forward Check the box to forward incoming calls to the assigned Forwarding Number automatically Busy Forward Check the box to forward incoming calls to the Forward incoming Number when the line is busy No Answer Forward Check the box to forward incoming calls to the Forward incoming Number after ringing timeout configurable from 10 to 60 seconds expires Call Hold Check the box to hold the call on the specific FXS port Note Call Transfer or Call Waiting can only be activated when Call Hold is checked Call Transfer Check the box to transfer the call to another destination Call Waiting Check the box to accept incoming call while talking Three Way Calling Service ID It is used for Nortel Style 3 Way conference Please enter correct service ID assigned on the SoftSwitch or IPPBX Local Mixer Enable 3 Way conference mixer on DVG This option is conflict to Three Way Calling Service ID don t enable these two options simultaneously Note The availability of a Three Way call also depends on your VoIP network Please also check with your service provider for these services D Link Systems Inc 47 DVG N5402GF User s Manual ADVANCED ADVANCED gt VoIP Calling Features CALL FEATURE CODE V Enable Call Feature Code Enable Disable Unconditional Forward FXS Representative Number 78 J c
3. Example for setting Wiresess profile via WPS method on Windows 7 Enter Network and Sharing Center Click Set up a new connection or network Control Panel Home View your basic network information and set up connections Manage wireless networks A x i s Change adapter settings WINTE Internet Change advanced sharing This computer settings View your active networks You are currently not connected to any networks Gs Set up a new connection or network up a wireless broadband dial up ad hoc or VPN connection or s point D Link Systems Inc 35 DVG N5402GF User s Manual SETUP Click Connect to the Internet Set up a new network C Configure a new router or access point Manually connect to a wireless network Connect to a hidden network or create a new wireless profile How do you want to connect Wireless Connect using a wireless router or a wireless network Broadband PPPoE Connect using DSL or cable that requires a user name and password P D Link Systems Inc 36 DVG N5402GF User s Manual SETUP Select a Wireless AP ou are currently not connected to any networks Change your networking settings ie Set up a new connection or network Not connected lt 4 Set up a wireless broadband dial up ad hoc or VPN connection d point Fail Connections are available Connect to a network Vireless Network Connection Connect or reconnect to
4. Is D or Global Number defined in Server 1 Is D or Global Number defined in Server 2 Is D or Global Number defined in Server 3 No Dial out as defined in the first match case by VoIP Router D Link Systems Inc 113 DVG N5402GF User s Manual Appendix Appendix Product Features WAN Combo e One Copper 10 100 1000Mbps auto negotiation auto crossover RJ 45 Ethernet port One Optical 100 1000Mbps SFP port tested with D Link SFP transceiver only Support static IP PPPoE and DHCP address assignment and dynamic DNS DDNS QoS IP TOS Type of Services and DiffServ Differentiated Services for both SIP signaling and RTP e NAT Traversal Port Forwarding STUN and Outbound Proxy e NTP Network Time Protocol RFC 1305 e Time Zone Support e MAC Address Clone e RTP Packet Summary packet sent packet received packet loss for voice quality analysis LAN e Four 10 100 1000Mbps auto negotiation auto crossover RJ 45 Ethernet ports e Supports router and bridge mode NAT mode and Non NAT mode e DHCP server Voice Features SIP RFC3261 compatible Voice codecs G 711 a ulaw G 726 G 729A G 723 1 iLBC GSM and G 722 CNG Comfort Noise Generation VAD Voice Activity Detection G 165 G 168 echo cancellation Adjustable Jitter Buffer and programmable Gain Control In Band DTMF Out Of Band DTMF relay RFC2833 SIP INFO Multiple SIP Proxy server entries with failover mechanism Pol
5. Domain Name Server Secondary IP eeeeeeseee m m 1492 168 95 1 1 Manual v SETUP Optional PPPoE Select this option if your ISP requires you to use a PPPoE Point to Point Protocol over Ethernet connection Enter the PPPoE Account PPPoE Password and re enter Password to confirm SETUP Internet Setup WAN 1 SETTINGS PPTP Server PPTP ID PPTP Password Confirm Password MTU WAN 1 Domain Name Server Domain Name Server Primary IP Domain Name Server Secondary IP Second Access IP Type Hostname Vendor Class ID r 1452 Manual 4 168 95 1 1 PPTP Point to Point Tunneling Protocol PPTP is a WAN connection Enter the IP Address Subnet mask PPTP Server PPTP ID and Password D Link Systems Inc 18 DVG N5402GF User s Manual SETUP SETUP Internet Setup WAN 1 SETTINGS Country foe ISP None v Username Password Dial Number Authentication Protocol Auto PAP CHAP v APN MTU 1492 3G USB Adapter 3G 3 5G WISP Enter Username Password Dial Number and APN to connect to Internet via 3G 3 5G WISP Users could also select a configured WISP from the list and DVG N5402GF will fill necessary parameter automatically SETUP Internet Setup WAN L
6. 1 PXS 522701 Idle 0 Disabled 01 00 30 S1702 Disabled 01 00 11 2 FXS 522702 Idle 0 Disabled 01 00 30 SERVER REGISTRATION STATUS DDNS Registration Disabled 01 00 11 STUN Registration Disabled 01 00 11 FXS SIP Proxy Hunting Number Registration Server 1 Disabled 01 00 11 Server2 Disabled 01 00 30 For Port Status it includes if each port registers to Proxy successfully the last dialed number how many calls each port has made since the VoIP Router is start etc Example S1 701 shows that the number of the first line which register to SIP Server 1 is 701 S2 2702 shows that the number of the second line which register to SIP Server 2 is 2701 For Server Registration Status it shows the registration status of DDNS Phone Book Manager and STUN D Link Systems Inc 101 DVG N5402GF User s Manual STATUS 3 4 3 LAN Client The Active Wireless Clients table displayed the identification and transmission status of active wireless clients on wireless LAN interface The DHCP Clients table displayed LAN device that has already been assigned an address from DVG N5402GF You can check if the DHCP client has obtain an IP address STATUS gt LAN Client In this section you can see what LAN devices are currently leasing IP addresses ACTIVE WIRELESS CLIENTS MAC Address Tx Packet RxPacket Tx Rate Mbps Power Saving Expired Time s DHCP CLIENTS IP Address MAC Address Live Time 192 168 5 1 00
7. Periodic Inform Interval 10800 sec Random Offset 600 Q 1800s Listen Port a001 0 disable 1 65535 Connection Request Username Connection Request Password Confirm Password oseosoosoe Enable TR069 Check the box to start TRO69 service Username Enter an available ACS user name Password Enter the ACS password Auto Config Server URL Enter the Provisioning Server s URL required by your VoIP Service Provider Periodic Info Enable It allows DVG connect to a TRO69 server periodically according to following parameters Periodic Info Interval Enter the time for auto provisioning Random Offset Enter the offset of the time for auto provisioning Listen Port TRO69 listen port for remote trigger D Link Systems Inc 97 DVG N5402GF User s Manual MAINTENANCE Connection Request Username Enter username for remote trigger Connection Request Password Enter password for remote trigger Note Contact your server provider if necessary MAINTENANCE TRO69 C Binding Server for Trigger Binding Server for Trigger Check the box to trigger a connection between Provisioning Server and the VoIP Gateway Provisioning Server will bind a port for the VolP Gateway to send provision request Binding Port Enter the port number of Provisioning Server is used for binding Binding Interval Enter the interval at which the VoIP Gateway will keep the binding D L
8. SNMP View gt View Name as 1 Subtree OID Indude Lindude i Indude Indude B Indude x Set Advanced gt SNMP Management gt SNMP Community gt Community Name for public and private Select a configured View Name D Link Systems Inc 86 DVG N5402GF User s Manual ADVANCED Community Name public Read Only v Read Write Read Only v Read Only Read Only D Link Systems Inc 87 DVG N5402GF User s Manual MAINTENANCE 3 3 MAINTENANCE 3 3 1 Device Management MAINTENANCE Device Management New Password eaaeo Confirm Password eoa New Password eeoa x Confirm Password eeoa Note There are two operating levels when entering the Web UI Logging in as the ADMIN allows you to change all settings A Web UI USER only has access to some settings Password By default there is no password configured It is highly recommended that you create a password to keep your router secure MAINTENANCE Device Management Port of Web Access from WAN a0 Web Idle Time Out 180 30 3600s TFTP Source Port s 1 65535 V Enable Web UI I Enable Telnet Service Port of Web Access from WAN Enter the port number when accessing the web based configuration utility from the WAN port Web Idle Time Out Enter the range of effecti
9. enter 148322495451 Numbers Input Key Upper Case Input Key Lower Case Input Key Symbols Input Key Letters Letters 00 A 11 a 41 71 O onoo A OO Na O B C D E F G H J K L M N O P Q R S ali U V W X Y Z D Link Systems Inc 110 DVG N5402GF User s Manual Appendix 5 Dialing Principles 5 1 Dialing Options Dial the phone number which you want to call and press to call out immediately Note that if the pound not dialed the number will be called out after 4 seconds by default The period between number dialed and call out is named Inter Digits Timeout Configurable from DTMF and PULSE default 4 seconds see page 50 If the phone number matches the setting of the Digit Map the phone number will be dialed out through the assigned VoIP Service Provider according to VoIP Route Profile automatically 5 2 Number Translation Phone number is dialed by user The system will check if the phone number is matched Digit Map Table If no matched is found from Digit Map Table it will use the phone number to look up number translation of the server set in VoIP Routing Profile Enter a phone is D ls D 1 defined in number D4 defined in Digit Number Translation Map table Table Translate De to global Translate D to private number based on Digit number based on Mumber Map Table Translation table ls the global number defined in Mumber Tra
10. s Manual Product Overview 1 Introduction 1 1 Product Overview The DVG N5402GF is designed to carry both voice and facsimile over the IP network and wirelessly share Internet access It uses the industry standard SIP call control protocol so as to be compatible with free registration services or VoIP service providers systems As a standard user agent it is compatible with all common Soft Switches and SIP proxy servers While running optional server software the VoIP Router can be configured to establish a private VoIP network over the Internet without a third party SIP Proxy Server The DVG N5402GF can be seamlessly integrated into an existing network by connecting to a phone set and fax machine With only a broadband connection such as an ADSL bridge router a Cable Modem or a leased line router the VoIP Router allows you to use voice and fax services over IP in order to reduce the cost of all long distance calls The DVG N5402GF is also an 802 11b g n wireless access point Allow wireless clients to connect to it and share your broadband Internet connection A built in 4 port switch makes it possible to connect up to 4 Ethernet enabled computers or devices to also share your Internet connection The DVG N5402GF can be configured a fixed IP address or it can have one dynamically assigned by DHCP or PPPoE It adopts either the G 711 G 726 G 729A G 723 1 or iLBC voice compression format to save network bandwidth while providing real time
11. toll quality voice transmission and reception D Link Systems Inc 4 DVG N5402GF User s Manual Telephone Interface Description 1 2 Hardware Description Front Panel Power Power LED A steady light indicates a proper connection to a power source Prov Alm A blinking light indicates the DVG N5402GF can not register with SIP Server or can not get the IP address A blinking light also indicates the DVG N5402GF is attempting to connect with the Provisioning server Once the service connects the LED will turn off The LED will light solid red if the self test or boot up fails Reg The Register LED will turn on and continuously working when DVG N5402GF is connected to a VoIP service provider The LED will flash if not connected to a service provider WAN When a connection is established the LED will light up solid The LED will blink to indicate activity If the LED does not light up when a cable is connected verify the cable connections and make sure your devices are powered on WLAN A steady light indicates a wireless connection A blinking light indicates that the VoIP Router is receiving transmitting from to the wireless network LAN When a connection is established the LED bottom will light up solid on the appropriate port The LEDs will blink to indicate activity If the LED does not light up when a cable is connected verify the cable connections and make sure your devices are powered on USB This indicates that DVG N5
12. Caller ID Choose the proper type for you FXS Caller ID Generation Disable V Send Caller ID After The First Ring FSK Caller ID Type Bellcore FXS Caller ID Generation Select DTMF FSK or FSK Type II Caller ID to enable the caller ID display function on FXS port When enabled the caller s phone number will be displayed on your phone set when the call comes through FSK Type II Caller ID is used for displaying the caller ID when receiving call waiting calls Note Make sure that your phone set supports Type II Caller ID before you select it Send Caller ID After The Firs Ring Check the box to send the caller ID after the first ring by FXS port otherwise the caller ID is sent before the first ring FSK Caller ID Type Either Bellcore ETSI or NTT can be selected D Link Systems Inc 46 DVG N5402GF User s Manual ADVANCED 3 2 1 3 Calling Features ADVANCED gt VoIP Calling Features It provides Call Forward Call Hold Call Transfer and Call Waiting It also provides Three Way Calling based on Nortel Soft Switch and works with the conference call supported by Voice Service Provider FXS REPRESENTATIVE NUMBER Unconditional Forward Busy Forward LINE1 FXS Do Not Disturb Unconditional Forward Busy Forward No Answer Forward After 10 60 20 5 Call Hold Call Transfer Call Waiting Three Way Calling Service ID Local Mixer rc r m r r r r r
13. ISP if needed USB SETTINGS My USB Type is 3G USB Adapter USB Type Select a USB device type 3G USB Adapter It allows you plug in a 3G dungle dial to WISP for Internet access Share Port Connect USB device such as a printer scanner or MFP Multifunction Printer to DVG and share it at Local Area Network Please refer to Share Port User Manual for USB Share Port application Note USB Share port is optional for particular area and users may need to pay additional royalty to get this feature D Link Systems Inc 43 DVG N5402GF User s Manual SETUP 3 1 6 Time and Date SETUP Time and Date The Time Configuration option allows you to configure update and maintain the correct time on the internal system clock From this section you can set the time zone that you are in anc set the NTP Network Time Protocol Server TIME SERVER Automatically synchronize with Internet time servers First NTP time server ntp L dlink com Second NTP time server ntp diink com tw TIME CONFIGURATION Current Router Time 2000 1 108 13 57 Time Zone GMT 12 00 Internationa Date Line West Enable Daylight Saving Automatically synchronize with Internet time servers The VoIP Router should automatically sync up with time servers First NTP time server Select the desired domain name of a NTP server as first priority Second NTP time server Select the domain name of a NTP server as second priority Curr
14. None Digit Map Table appears like Scan YoIP Dial User Dial VoIP Route ROULE Profile Code out Length Auto voIP o 09 10 First 1 As you dial the phone numbers starting with 09 like 0912345678 the call will only go through Server 1 local VSP D Link Systems Inc 54 DVG N5402GF User s Manual ADVANCED Example 2 Multiple Route The number translation of Server 1 is blank and the number translation of Server 2 appears like NUMBER TRANSLATION oIP Dial Out defined here overrides Digit Map Copy From None x Scan Code YoIP Dial out 03 00453 The VoIP route profile appears like Description 1 2 LocalServer Server 1 None LongDistance Server 2 Server 1 None None None None None None None None None None None None None None None None CARY Digit Map Table appears like Scan VoIP Dial User Dial Code out Length VoIP Route Route Profile 09 oIP 1 03 VoIP 2 E As you dial the phone numbers staring with 03 like 0312345678 the number will be changed to 0045312345678 followed the number translation of Server 2 and the call will go through Server 2 free VSP at first If failed the number will be back to 0312345678 and the route will be changed to Server1 local VSP D Link Systems Inc 55 DVG N5402GF User s Manual ADVANCED Example 3 Multiple Route The number translation of Server 1 is blank and the number translation of Ser
15. a wireless wired dial up or VPN network 4 link ba wd Choose homegroup and sharing options Access files and printers located on other network computers or c i Troubleshoot problems Diagnose and repair network problems or get troubleshooting infa i Open Network and Sharing Center Click OK to start setup 2se homegroup and sharing optic T Connect to a Network ccess files and printers located on ot Do you want to set up your network rouDlesnoot problems Diagnose and repair network problems This is a new router that has not been set up Click OK to start setup nN ect to the network without set D Link Systems Inc 37 DVG N5402GF User s Manual SETUP Enter the 8 digit PIN from DVG N5402GF label then click Next Note If you have ever click Change PIN button on the WEB UI of DVG N5402GF please enter the PIN number displaied on WEB GUI You can find the numeric PIN on a label attached to the router or in the printed information that came from manufacturer Give your network a name Your network needs a unique name so that it can be easily identified It is best to keep the name short 25 characters or less and recognizable Type your network name Security enabled network ChangThird WIN7E_Networl Your network is being set up using WPA2 Personal Change passphrase security level and encryption type advanced D Link Systems Inc 38 DVG N5402GF Use
16. detect FAX by T 30 Fax T 38 Fax T 30 Modem or T 30 Only Choose the type of FAX protocol and set the related settings FAX MODEM T 30 Fax v T 30 Fax v Option Fax Detection Content of SDP of re INVITE re INVITE with T 38 from remote party Disable No N A Accept and change RTP to T 38 T 38 Fax Yes re INVITE with T 38 and T 30 Accept and change RTP to T 38 T 30 Fax Yes re INVITE with T 30 Accept and change RTP to T 38 T 30 Detect CED Fax Modem only re INVITE with T 30 Accept and change RTP to T 38 T 30 Only N N A Accept and change RTP to T 38 fl T 38 Native Yes re INVITE with T 38 Accept and change RTP to T 38 T 30 V 152 Yes N A Accept and change RTP to T 38 Note When a fax tone is detected from the call the VolP Router will automatically switch from voice mode to fax mode Hence the fax settings will be temporarily applied to a specific port which detects the fax tones instead of its default voice settings D Link Systems Inc 60 DVG N5402GF User s Manual ADVANCED gt VoIP gt FAX The function is auto detect FAX by T 30 Fax T 38 Fax T 30 Modem or T 30 Only Choose the type of FAX protocol and set the related settings FAX MODEM C Switch FAX On CED Detection C Restrict T 38 FAX Detection Sensitivity FAX T 38 High Speed Redundancy Low Speed Redundancy FAX Max Rate High Speed Packet Time FAX T 30 FAX Codec T 30 Bypass Payload Type FAX Jitter Buff
17. lt LAN Port 4 Enable Port It is to active des active LAN port physical connection Incoming Rate Limit Set the incoming from LAN to WAN rate limit of a specific LAN port can not exceed the real downstream bandwidth Outgoing Rate Limit Set the outgoing from WAN to LAN rate limit of a specific LAN port can not exceed the real upstream bandwidth NAT Bridge Select the VoIP Router serving as a Router with NAT or Bridge between WAN port and LAN port without NAT Note If you set a LAN port to be bridge mode that the LAN port will be bundled with WAN If you would like to connect to DVG N5402GF at the bridged LAN port you must enter WAN port IP VLAN ID Assign a VLAN ID for DVG N5402GF to transit traffic through out at WAN port for WAN LAN bridge mode The packets are un tagged at LAN port and added tag at WAN port Note It is not allowed to change VLAN ID for NAT mode LAN ports The VLAN ID of NAT LAN ports are bundled with WAN 1 which assigned at Internet Setting page The packets are un tagged at LAN port and added tag at WAN port D Link Systems Inc 42 DVG N5402GF User s Manual SETUP 3 1 5 USB Settings SETUP gt USB Settings Use this section to configure your USB port There are several configurations to choose from Network USB and 3G USB Adapter If you have trouble accessing the Internet through the router Double check the settings you entered on this page and verify with your Internet Service Provider
18. this indicates that the VoIP Router currently is not connected to the Internet Please check and make sure the cable connections account numbers and passwords are correct Dynamic IP DHCP Settings After entering IVR mode dial 114 When voice prompt plays Enter value dial 2 to select DHCP Saving settings press 509 Save Settings Please restart the system After the system is restarted press 101 to check whether or not the IP address was retained Note If the system does not play back the IP address this indicates that the VoIP Router failed to communicate with a DHCP server Please check with your DHCP server or ISP ADSL PPPoE Settings Note Complete PPPoE settings should include Select PPPoE option 3 of 114 PPPoE account 121 and PPPoE password 122 Please contact your local Internet Service Provider ISP if you have any questions D Link Systems Inc 108 DVG N5402GF User s Manual VoIP Router Configuration IVR Select a PPPoE After entering IVR mode dial 114 When voice prompt plays Enter value dial 3 to select PPPoE PPPoE Account Settings After entering IVR mode dial 121 When voice prompt plays Enter value enter the account number followed by Example If the account is 87654321 hinet net please enter 08 07 06 05 04 03 02 01 71 48 49 54 45 60 72 54 45 60 Note It is necessary to enter two digits for each alphabet number for example you must enter 0
19. 1 for 1 and 11 for A Using the web Interface to configure your PPPoE account details is recommended Refer to the PPPoE Character Conversion Table on the next page for key mappings if you choose to use IVR setup PPPoE Password Setting After entering IVR mode dial 122 When voice prompt plays Enter value enter the new password followed by Example If the password is 3t2ixiae please enter 03 60 02 49 64 49 41 457 Save Settings and Restart To save settings dial 509 Save Settings The system will save the settings Please restart the system Wait for about 40 seconds for the system to restart then enter 101 to check whether the IP address was retained If the system does not play back the IP address after dialing 101 this indicates that the VoIP Router currently is not connected to the Internet Please check and make sure the cable connections account numbers and passwords are correct D Link Systems Inc 109 DVG N5402GF User s Manual VoIP Router Configuration IVR 4 2 1 PPPoE Character Conversion Table The table below provides a list of PPPoE conversion codes The first row high lighted of each pair of the column lists the numbers alphabets or symbols and the second row high lighted of each pair of the column Input Key represents the codes to be entered for the corresponding numbers alphabets or symbols For example to enter D Link according to the table below
20. 1 None None LongDistance Server 2 Server 1 None InternationalCall Server 3 Server 2 Server 1 YoIPSTUN Server 2 None None UK Server Server 3 None None None None None None None None None None None None None None E E E E E E E E E E None None None Method 1 Single mapping Fill a short code into the Scan Code column and enter the desired phone number into the VoIP Dial out column D Link Systems Inc 57 DVG N5402GF User s Manual ADVANCED For example Scan Code 09 VoIP Dial out 0912345678 User Dial Length 2 Route Auto VoIP Route Profile Route 1 Scan YoIP Dial User Dial Code out Length YoIP Route Route Profile 09 0912345678 2 VoIP 1 E 3 Pick up the handset and dial 09 and the system will do the things as follow 1 Change the phone number to the global number 09 is changed to 0912345678 Then follow the VolP Route Profile 1 D Link Systems Inc 58 DVG N5402GF User s Manual ADVANCED 3 2 1 7 DTMF amp PULSE ADVANCED VoIP gt DTMF amp PULSE It can help to solve the dialing number form these parameters Dial Wait Timeout 110 1 608 Inter Digits Timeout 4 1 608 Minimum DTMF ON Length s0 40 500ms Minimum DTMF OFF Length 500 ms DTMF Detection Sensitivity r DTMF Detection Volume Sensitivity DTMF Output Volume FXS Pulse Detection Enable Out of Band DTMF Out of Band DTMF RFcC2833 SIP Info Enable Hook Flash E
21. 19 d2 35 45 60 2147448608 Refresh D Link Systems Inc 102 DVG N5402GF User s Manual STATUS 3 4 4 Statistics STATUS Statistics All of your Internet and network connection details are displayed on this page The Firmware version is also displayed here PHONE 1 Talk Information G 711 u law 64kbps Packet Sent Packet Received Packet Lost The Last Packet s Source IP The Last Packet s Source Port Display the information of the last call made Press Refresh button to get the latest RTP Packet Summary 3 4 5 Routing Table STATUS Routing Table This table is showing you the router forwards list Routing Table enables you to view the information created by the router that displays the network interconnection topology Destination Netmask Gateway 61 221 24 0 255 255 255 224 0 0 0 0 192 168 8 0 255 255 255 0 0 0 0 0 default 0 0 0 0 61 221 24 1 Refresh The Routing Table stores the information for particular network destination around the VoIP Router Press Refresh button to generate the details D Link Systems Inc 103 DVG N5402GF User s Manual STATUS 3 4 6 Logout If setting or parameter has been changed remember to save the changes before you logout the configuration menu Logout Logging out will close the browser Logout D Link Systems Inc 104 DVG N5402GF User s Manual VoIP Router Configuration IVR 4 Configuring the VoIP Router through IVR VoIP tra
22. 3 Make sure security used by every device in the same wireless network is compatible with the wireless AP 3 1 3 1 Wireless Basic SETUP gt Wireless Setup gt Wireless Basic Use this section to configure the wireless settings for your D Link router Please note that changes made on this section will also need to be duplicated to your wireless clients and PC Enable Wireless LAN Interface Wireless Network Name SSID dink Wireless Channel Auto Scan recommended v 802 11 Mode Mixed 802 11n 802 11g and 802 11b vi Mode AP vi Channel Width 20 MH Broadcast SSID Enable WMM Enable Universal Repeater Mode Acting as AP and client simultaneouly Enable Wireless LAN Interface Enable wireless basic settings on LAN interface Wireless Network Name SSID SSID is the name of your wireless network All wireless equipped devices share the same SSID to communicate with each other It must be unique to identify separated wireless network For security you should change the default SSID to a special ID Wireless Channel Select a clear and appropriate channel for your wireless network A device on your wireless network must use a specific channel to transmit and receive data If wireless network has overlap change a different channel number 802 11 Mode The VoIP Router can operate in 2 4GHz ISM band with different speed of wireless connection Select the wireless band of your network 802 11b only A
23. 402GF detects a supported 3G modem dungle or a USB device This function Is optional Phone This LED displays the VoIP status and Hook Ringing activity on the phone port that is used to connect your normal telephone s If a phone connected to a phone port is off the hook or in use this LED will light solid When a phone is ringing the indicator will blink WPS Flashing in blue as DVG N5402GF processing WPS PBC wireless connecting progress D Link Systems Inc 5 DVG N5402GF User s Manual Telephone Interface Description Rear Panel 1 WiFi Switch trn on off wireless LAN Phone Port 1 2 Connect to your phones using standard phone cabling RJ 11 USB Connect to a 3G USB dungle or a printer This function Is optional LAN Connect to your Ethernet enabled computers using Ethernet cabling WAN Connect to your broadband modem using an Ethernet cable YY A YY Ground A conducting connection with the earth Connect with the ground so as to make the earth a part of an electrical circuit using metal wire a Power Receptor Receptor for the provided power adapter 8 Power Switch Press down to turn on DVG N5402GF WARNING DO NOT 1 connect the phone ports to each other FXS to FXS or 2 connect any phone port directly to a PSTN line FXS to PSTN or to an internal PBX line FXS to PBX extension 3 Stacking is forbidden Doing so may damage your VoIP Router D Link Systems Inc 6 DVG N5402GF User s Manu
24. D Link DVG N5402GF VoIP Wireless Router User s Manual Version 1 0 July 2011 2011 D Link Corporation All rights reserved Reproduction in any manner whatsoever without the written permission of D Link Corporation is strictly forbidden Trademarks used in this text D Link and the D Link logo are trademarks of D Link Corporation D Link Systems Inc Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products D Link Corporation disclaims any proprietary interest in trademarks and trade names other than its own Warranty please contact your D Link Authorized Reseller or the D Link Branch Office nearest your place of purchase for information about the warranty offered on your D Link product Information in this document is subject to change without notice FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communication However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to ra
25. G N5402GF User s Manual MAINTENANCE Backup Configurations Template File MAINTENANCE Backup and Restore SYSTEM BACKUP CONFIGURATIONS TEMPLATE FILE Backup YoIP Router configurations template file You may save your VoIP router configurations template file to a file on your PC Note Please always save configuration template file first before viewing it Backup Settings Click the Backup Settings button to save your current settings to a template file for editing Update Settings MAINTENANCE Backup and Restore SYSTEM UPDATE SETTINGS Update VoIP Router settings You may update your router settings using your saved files Settings File Name Browse Update Settings To restore a system settings file click on Browse to search the local hard drive for the file to be used Once you locate the file click Upload Settings to overwrite the current settings with the settings saved to the file Restore Default Settings MAINTENANCE Backup and Restore SYSTEM RESTORE DEFAULT SETTINGS Restore YoIP Router settings to the factory defaults Restore Default Settings Select Restore Default Settings to reset the VoIP Router s settings back to the factory default settings D Link Systems Inc 90 DVG N5402GF User s Manual MAINTENANCE 3 3 3 Firmware Update The VoIP Router supports a software upgrade function from a remote server Please consult your VoIP Service Provider for information abou
26. INK SPEED WAN Link Speed WAN Link Speed Select WAN port link speed SETUP Internet Setup Connection VoIP Connection Interface Select a WAN interface for DVG N5402GF VolP traffic D Link Systems Inc 19 DVG N5402GF User s Manual SETUP SETUP Internet Setup Factory Default MAC Address 00 17 94 98 4F 6C Your MAC Address 00 04 79 60 17 28 Current MAC Address XX IX IXKIXXERXEXX Factory Default MAC Address The original MAC address of the VoIP Router Your MAC Address It is left blank as you log in via the WAN port Current MAC Address It shows the current MAC Address if you ever used the different MAC address from Factory Default MAC Address You can click Clone to automatically copy the MAC address of the Ethernet Card installed in the computer used to configure the device Note This is only necessary to fill the field if required by your ISP SETUP gt Internet Setup Use this section to configure your Internet Connection type If you are unsure of your connection method please contact your Internet Service Provider DHCP Static IP O PPPoE PPTP G USE Advanced Configuration Click Advanced Configuration for 802 11q p VLAN tag or dual WAN access configuration D Link Systems Inc 20 DVG N5402GF User s Manual SETUP WAN SETTINGS Enable Type Enable VLAN Tagging VLAN ID Priority WAN 1 DefaultRoute DHCP WAN 2 a
27. ION WIRELESS LAN Wireless Radio Wireless Network Name SSID 802 11 Mode Wireless Channel Wireless Security Mode DHCP SERVER DHCP Server IP Pool Range Lease Time Domain Name Server HARDWARE DVG N54025P 2000 01 01 08 55 53 GE_1 00 001122334455 Disconnected 192 168 100 1 255 255 255 0 192 168 100 254 168 95 1 1 001122334456 192 168 8 254 255 255 255 0 Enable DVG N54025P Mixed 802 11n 802 11g and 802 11b Auto Scan recommended WPA2 Mixed Enabled 192 168 8 1 192 168 8 250 1 hour s 168 95 1 1 B1 1 2 2 86 135 263 STATUS For WAN Port Information it shows IP address subnet mask default gateway and DNS server If you use PPPoE to obtain IP you will know if the IP is obtained through this If IP address subnet mask default gateway is blank it means that the VolP Router does not obtain IP For LAN Port Information it shows LAN port IP subnet mask and the status of DHCP server For Hardware it shows the hardware platform and driver version D Link Systems Inc 100 DVG N5402GF User s Manual STATUS 3 4 2 VoIP Status STATUS VolP Status The information reflects the current status of yourVoIP Router connection Display the port status of each proxy server in the field of Extension Number Proxy Register and FXS Representative Number PORT STATUS No Type parene Line Status Calls Number Proxy Register 1701 Disabled 01 00 11
28. IP Pool Ending Address 192 168 8 250 C IP Pool Uses Other Default Gateway Lease Time 1 1 9999 hours Domain Name Server Assignment Auto O Manual Enable DHCP Server This variable is to assign the IP address for the devices connected to LAN port of the VolP Router IP Pool Starting Address Enter the starting IP address for the DHCP server s IP assignment IP Pool Ending Address Enter the ending IP address for the DHCP server s IP assignment IP Pool Uses Other Default Gw Check the box to assign different default gateway for DHCP clients IP Pool Default Gateway Enter the new default gateway that is different from LAN IP of the VolP Router IP Pool Subnet mask Enter the new subnet mask Lease Time Enter the length of time for the IP lease Domain Name Server Assignment Select Auto or Manual to get the IP address of Domain Name Server assigned by ISP or manually Domain Name Server IP Enter the primary and secondary IP address of Domain Name Server if Domain Name Server Assignment is Manual Otherwise the VolP Router will not be able to access hosts using hostnames instead of IPs D Link Systems Inc 41 DVG N5402GF User s Manual SETUP SETUP LAN Setup LAN PORT CONTROL Enable Incoming Rate Outgoing Rate Port Limit Limit LAN Port 1 Ful Full NAT v Port NAT Bridge VLAN ID lt LAN Port 2 Ful o Ful NAT Ful iv Ful J NAT S LAN Port 3 Full Full J NAT
29. Internet sharing device for the listen port and communication ports RTP ports of the VolP Router NAT IP Domain Enter the real public IP address of the IP sharing device or the router or enter a true URL Uniform Resource Locator when DDNS is used Please refer to the DDNS settings Note If you are setting a public IP in this field it has to be a static public IP otherwise VolP communication may not be established properly Please contact your ISP to check if your Internet connection has static public IP addresses Enable STUN Client Check the box to use the STUN protocol prevents problems from setting the IP sharing function Some NATs do not support this protocol Note You can use the Status gt STUN Inquiry page to detect the NAT type of your Internet sharing device If the NAT type is Symmetric NAT then the VoIP Router is not able to traverse the NAT It is not a flaw of the VoIP Router design but rather a limitation of the STUN protocol STUN Server IP Domain and Port Enter the IP address and listen port of the STUN server You can set two STUN server IPs separated by a semicolon D Link Systems Inc 81 DVG N5402GF User s Manual ADVANCED 3 2 5 3 STUN Inquiry Use STUN Inquiry to detect your IP sharing device s NAT type and communication between a STUN server and client ADVANCED Advanced Network STUN Inquiry Use STUN Inquiry to detect your IP sharing device s NAT type and communication betw
30. ODE To protect your privacy you can configure wireless security features This device supports three wireless security modes including WEP WPA PSK and WPA WEP is the original wireless encryption standard WPA provides a higher level of security WPA PSK does not require an authentication server The WPA option requires an external RADIUS server Wireless Security Mode None v Select DDID Select an SSID to configure wireless security mechanism Security Mode Select the encryption authentication type None WPA WPA2 and WPA2 Mixed D Link Systems Inc 30 DVG N5402GF User s Manual SETUP WEP Authentication Mode SETUP gt Wireless Setup gt Wireless Security WEP IF you choose the WEP security option this device will ONLY operate in Legacy Wireless mode 802 11B G WEP is the wireless encryption standard To use it you must enter the same key s into the router and the wireless stations For 64 bit keys you must enter 10 hex digits into each key box For 128 bit keys you must enter 26 hex digits into each key box A hex digit is either a number from 0 to 9 or a letter From 4 to F For the most secure use of WEP set the authentication type to Shared Key when WEP is enabled You may also enter any text string into a WEP key box in which case it will be converted into a hexadecimal key using the ASCII values of the characters 4 maximum of 5 text characters can be entered For 64 bit keys and a maximum of 13 char
31. P gt Wireless Setup gt Site Survey SSID BSSID Channel Type Encrypt Signal Select 802 11 SSID 00 00 00 15 74 34 no WPA PSK WEP WPA2 PSK 802 11 00 00 00 12 c5 a0 802 1 1 4irStation 00 00 00 bc 95 e6 802 113 00 00 00 cb Fa 73 AP AP AP AP Site Survey When wireless client mode is enabled click the Refresh button to display any Access Point on your wireless network so that a wireless client can obtain SSID BSSID Channel Type Encryption and Signal through scanning using this Site Survey tools Example 1 Select the Wireless AP and click Accept bottom SSID BSSID Encrypt Signal 802 11 SSID 00 00 00 15 73 34 no 802 11 00 00 00 12 cS a0 WPA PSK 802 1 1AirStation 00 00 00 bc 95 e6 WEP 802 118 00 00 00 cb Fa 73 WPA2 PSK nce 2 Enter the password of the Wireless AP and click Apply bottom PRE SHARED KEY Pre Shared Key Format _Passphrase Pre Shared Key 123451234 3 Save the configuration and restart DVG N5402GF SYSTEM SAVE AND REBOOT Click the button below to save and reboot the VoIP Router Save All Settings D Link Systems Inc 34 DVG N5402GF User s Manual SETUP 3 1 3 3 WPS SETUP gt Wireless Setup gt WPS Enable WPS Self PIN Number 46557506 Change PIN PIN Configuration Start PIN Push Button Configuration Start PBC It allows users establish wireless connect between DVG N5402GF and computers via WPS Wireless Protect Setup method
32. PSK uses a specific characters sting like password instead of a user authentication SETUP gt Wireless Setup gt Wireless Security WPA PSK Use WPA or WPA2 mode to achieve a balance of strong security and best compatibility This mode uses WPA for legacy clients while maintaining higher security with stations that are WPA capable Also the strongest cipher that the client supports will be used For best security use WPA Only mode This mode uses AES CCMP cipher and legacy stations are not allowed access with WPA security For maximum compatibility use WPA Only This mode uses TKIP cipher Some gaming and legacy devices work only in this mode To achieve better wireless performance use WPA2 Only security mode or in other words AES cipher WPA Authentication Mode Personal Pre Shared Key v WPA Cipher Suite kP as Both PRE SHARED KEY Pre Shared Key Format Passphrase Pre Shared Key Select the type of WPA PSK WPA PSK WPA2 PSK WPA2 Mixed PSk choose the proper security mode according to your wireless network WPA Authentication Mode Select Personal Pre Shared Key WPA Cipher Suite WPA Cipher Suite is used for the configuration of WPA or WPA2 Mixed TKIP TKIP is the security protocol used in WPA The length of TKIP encryption is longer than WEP encryption that increases the complexity of decoding for crackers AES The most powerful encryption algorithm that is commonly used in WPA WPA2 Cip
33. UIGTIONN eerren E vemtncc tee a puwed E sewn a ee bare ets Oa eae nee ae 4 NA Product COON CNV OW eaten ere cia dsc aerate ec A EEAO E EEEE aaron tc aber d a EE O a E EER 4 122 Hardware DESCIiOlOMN sciatica dewaazeasecac A E E a EA 5 2 Getma Stane esr aa aA Ea A E AT EES 8 3 VOIP Router Web Configuration osiers e NEE TE ee 16 Soe TUR ara e aint a AA E aa E A ANE a 16 O 41 WALCRMEL SE LUD aena E A a E A A e E E EA 16 3 bo VOIP SEUD ee a a a aA 22 Oe FO Wireless 6 IUD cerrar riren 28 TELAN SO UID wsesigsrachaice sie vias E EE ware sig w ge inwin cain alas Se hase eral A alate dae eect ies eae 40 oS al eo WL Fs rot 111 6 ee enn SP Per ra rE mmr On es EE rea A PP Ee i Se ee ee eee 43 1 OIG CAG DIE nire sar tines Ue atu h oe Sheen eka E in aaah set hi en hes ae hile BE a Iuka tt 44 32 ADVANCED meee pee re coe 45 S2 l VOIP sre aeea ENN AE waters a aed no AE AEA 45 3 2 2 ACCESS CONTO wii teh TEE A a T S T 72 372 0 FPrewWaland DMZ eurre er aE E E TTE E E AEE EE EE a 73 J2AAWaNCEd VWINCICSS sire tena tin e E a e a e ENa 78 O27 ACVANCECINGIWONK or E A E EAT daten void samatonaauaee 80 eO NM Ea re ET A EE TE E A Aa 85 3 0 WAIN TENANG Eis ss amcteats eycesmeceyaisensep a EOE TEE 88 B70 Device Managemen esner orrn ea aE ccoraiers ste wicte lt cretw are eseraiewy N EEEE E 88 39 2 BACKUP aNd FOSIONS sarees n EE EEE E AN E EER 89 Joe RMW UDOAIS ioa E a A E E a T S 91 297 Dynami ONS orre E EA EE EE E O ET 92 TF OG OE INOS ee E w
34. acters For 128 bit keys WEP Key Length 64 bit length applies to all keys Default Tx Key l WEP Key Format ASCII 5 characters WEP Key 1 WEP Key 2 WEP Key 3 WEP Key 4 WEP Key Length Select 64 bit or 128 bit data encryption Default Tx Key You can select one of the keys as active key at a time WEP Key Format Select the preferred WEP Key Format according to which WEP encryption you choose When WEP 64bits is enabled you can select ASCII 5 characters and Hex 10 characters When WEP 128bits is enabled you can select ASCII 13 characters and Hex 26 characters WEP Key 1 4 You can manually input key value from Key1 to Key4 Type a character sting and apply changes For a 64 bit WEP key Enter 5 characters ASCII sting or 10 hexadecimal characters 0 9 A F For a 128 bit WEP key Enter 13 characters ASCII sting or 26 hexadecimal characters 0 9 A F Note WEP authentication is not supported at 802 11n mode It recommends select WPA or WPA2 for higher secure D Link Systems Inc 31 DVG N5402GF User s Manual SETUP WPA Authentication Mode The wireless network can use WPA Authentication to verify whether a wireless device is allowed to access your Access Point or not You can choose to use Enterprise RADIUS method or Personal Pre Shared Key The encryption mechanism used for RADIUS and WPA PSK is the same The difference between the two is that WPA
35. agmented into small units to pass over a network medium that can not support the original packet size If you encounter a busy network a lower value of Fragment Threshold could improve performance If the traffic flows are not very busy a higher Fragment Threshold provides good network performance In most case keeping the default value 2346 is recommended RTS Threshold RTS Threshold is a mechanism to implement in collision avoidance In a large wireless network two stations do not hear each other but can hear wireless access point When the two send data to Access Point at the same time it may result in data collision and a loss of messages for both wireless stations In most case keeping the default value 2347 is recommended RF Output Power You can adjust the percentage of power 100 50 25 10 5 of your VolP Router to change the coverage of wireless network Keep the default value 100 to reach full range D Link Systems Inc 78 DVG N5402GF User s Manual ADVANCED 3 2 4 2 Access Control The Access Control setting provides a service that you can control different access rights for different wireless clients connected to your VoIP Router The local and remote stations are limited to access Internet through your Access Points using MAC address of wireless client Choose the appropriate Access Control Services from Wireless Access Control Mode option ADVANCED gt Advanced Wireless gt Access Control Allows you to configure ac
36. al Telephone Interface Description WPS WPS button for wireless WPS PBC setup method Antenna Connect to a wireless network Reset button Use to restore factory default settings Use Reset Button to restore factory default settings 1 Press and hold the reset button for 5 seconds 2 As Alarm indicator is blinking please release the reset button Factory settings will be restored D Link Systems Inc 7 DVG N5402GF User s Manual SETUP 2 Getting Started To access the web based configuration utility open a web browser such as Internet Explorer and enter the IP address of the DVG N5402GF from WAN port Ta Tools Help Nols alp Open your Web browser and type Back Q x 6 T 4 http 192 168 8 254 into the URL address box Press the Enter or Return Key y Address htte 192 169 9 254 Welcome to DVG N5402SP Web Management Username admin v Password Remember my login info on this computer Click Login to enter Web Site D Link Systems Inc 8 DVG N5402GF User s Manual SETUP There are two ways to set up your Internet connection you can use the Web based Internet Connection Setup Wizard or you can manually configure the connection Please make sure you have your ISP s connection settings first if you choose to setup manually INTERNET CONNECTION WIZARD You can use this wizard for assistance and quick connection of your new D Link Router to the Internet You will b
37. an which combines the original feature of Digit Map and Speed Dial You can use or in the column of Scan Code and VoIP Dial out represents a single digit and represents a wildcard The function of the signs is to mapping the numbers between the number received from user and the replaced or modified number for actual dial out With this function users can easily add certain leading digits to replace a full set of numbers There are 50 sets of leading digit entries to choose voice routing interface ADVANCED gt VolP Digit Map There are 50 sets of leading digit entries to choose voice routing interface Auto select YoIP or Deny Enable Pound Key Function Default Call Route va Default oIP Route Profile 1 Enable Pound Key Function Check the box to treat as a digit and send out with other numbers when dialing If you un check the box and is pressed after dialing it will speed up the phone number detection of the VoIP Router Default Call Route Select VoIP or Deny as the default call route for the calls Default VoIP Route Profile Enter the Profile ID ranging from 1 10 for the Default VoIP routing ADVANCED VolP Digit Map Scan Code oIP Dial out User Dial Length Route oIP Route Profile Scan Code Enter the digits for the VolP Router to scan while user is dialing VoIP Dial out Enter the actual dialing number rule for the VolP Router
38. and function codes without turning on the PC Note When finishing the setup make sure the new settings are saved This will enable the new settings to take effect after the system is restarted Instructions FXS Port Connect to telephones To access IVR mode passwords should be entered password Alphabets to digits conversion information is provided in the PPPoE Character Conversion Table Refer to Page 71 When correct IVR passwords are entered and accepted an indication tone can be heard indicates the system is in IVR setup mode Enter function codes to check or configure the VolP Router Please refer to page 68 for function codes Example If your password is 1234 enter star star 1 2 3 4 pound and now you are entering IVR setup mode Next enter a function code to check or configure the VoIP Router If your password is admin enter star star star 41 44 53 49 54 pound Please refer to the IVR Functions Table page 68 for available functions and codes D Link Systems Inc 105 DVG N5402GF User s Manual VoIP Router Configuration IVR Once the setting or query has been completed you can hear a dial tone Use the same procedure to make a second query or setting To exit IVR mode simply hang up the phone Example enter you are now in IVR mode gt enter 101 to query the current IP address gt the system responds with an IP address You can continue with more set
39. arity reversal generation FXS T 30 G III Real time T 38 Secured T 38 FAX relay DTMF FSK Bellcore amp ETSI Caller ID generation Support Caller ID Restriction CLIR Digit Map for dial plan Speed Dial Local phone book for peer to peer calling E 164 Numbering amp ENUM support Hot Line Warm Line support Single Number Account reprehensive number for multiple ports Call features o Call Hold Call Waiting Call Pickup o Call Forward Unconditional Busy No Answer o Call Transfer Unattended Attended o Three Way Calling Media Server required e Analogue interface o Connector RJ 11 o Signaling protocol Loop Start D Link Systems Inc 114 DVG N5402GF User s Manual Appendix Configuration amp Maintenance e Configuration methods o Web o IVR o Telnet e Status reports o Port status o Registration status o Ping tests o Hardware software information e Firmware Upgrade through TFTP FTP or HTTP server e Configuration Backup Restore e Reset button with restore factory default function D Link Systems Inc 115
40. cess control of the wireless LAN interface Access Control Mode Disable Apply Cancel MAC Comment Access Control Mode Disable The VolP Router does not response to any access rules You are not allowed to make configuration changes on this page Allow When Allow Listed is enabled only those wireless clients whose MAC addresses are in the Access Control List have rights to connect to your Access Point Deny When Deny Listed is enabled only those wireless clients whose MAC addresses are in the Access Control List will be blocked and restricted access to your Access Point MAC Address Specify the MAC address which you want to allow deny access your Access Point Comment The space is reserved for comment or notation D Link Systems Inc 79 DVG N5402GF User s Manual ADVANCED 3 2 5 Advanced Network 3 2 5 1 QOS WAN QoS ADVANCED Advanced Network gt QoS Choose WAN or LAN to configure C Enable WAN Qos WAN QOS Downstream Bandwidth Full Rate Upstream Bandwidth Full Rate ToS IP Precedence ToS DiffServ Settings Diffserv DSCP TOS IP PRECEDENCE Signaling Precedence 3 Flash v Voice Data Precedence 5 CRITIC ECP Enable WAN QoS Check the box to guaranty the voice quality The system reserves the bandwidth for voice packets and the data transmission is distributed to less bandwidth Downstream Bandwidth Select the downstream ban
41. d be shown on Result Table MAINTENANCE gt Diagnostics Ping Test Ping Test sends ping packets to test a computer on the Internet Ping Destination Number of Ping Ping Packet Size RESULT 192 168 8 254 56 5600 bytes 192 168 8 254 ping statistics 4 packets transmitted 4 packets received 0 packet loss round trip min avg max 0 0 0 0 0 0 ms PING 192 168 8 254 192 168 8 254 100 data bytes 108 bytes from 192 168 8 254 icmp_seq 0 ttl 255 time 0 0 ms 108 bytes From 192 168 8 254 icmp_seq 1 ttl 255 time 0 0 ms 108 bytes from 192 168 8 254 icmp_seq 2 ttl 255 time 0 0 ms 108 bytes from 192 168 8 254 icmp_seq 3 ttl 255 time 0 0 ms D Link Systems Inc 94 DVG N5402GF User s Manual MAINTENANCE 3 3 6 2 Outward Test MAINTENANCE gt Diagnostics Outward Test H F DC Voltage Hazardous and foreign DC voltage H F AC Voltage Hazardous and foreign AC voltage Enable Pass Loop Open H F DC Voltage H F AC Voltage Tip Ring Short Failed o al C Enforced Test Ignore Port State It allows operator to verify whether it is some problem on the cable between phone sets and DVG N5402GF FXS ports Enable Select the lines you want to test Including Channel In Used Since the line test will interrupt a talking call that DVG N5402GF will ignore the in used line If you would like to test all the lines you select even it is in used
42. dio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Warnung Dies ist ein Produkt der Klasse B Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen In diesem Fall kann vom Benutzer verlangt werden angemessene Massnahmen zu ergreifen Precauci n Este es un producto de Clase B En un entorno dom stico puede causar interferencias de radio en cuyo case puede requerirse al usuario para que adopte las medidas adecuadas Attention Ceci est un produit de classe B Dans un environnement domestique ce produit pourrait causer des interf rences radio auquel cas l utilisateur devrait prendre les mesures ad quates Attenzione Il presente prodotto appartiene alla classe B Se utilizzato in ambiente domestico il prodotto pu causare interferenze radio nel cui caso possibile che l utente debba assumere provvedimenti adeguati Contents Tomt OC
43. dvanced International Call Prefix Digit Country Code Albania 355 Long Distance Call Prefix Digit Area Code E164 Numbering To Invite Proxy ENUM Header Exception 070 International Call Prefix Digit Enter the International call prefix Country Code Select the desired country code from the drop down menu or enter the country code if Other is selected Long Distance Call Prefix Digit Enter the long distance prefix digit for making a long distance call Area Code Enter the area code E 164 Numbering To Invite Proxy This variable is followed the E 164 rule but it depends on the SIP proxy server Click the check box to send the number following the E 164 rule by the VolP Router ENUM Header Exception Enter the prefix number that the VolP Router sends the number without followed the E 164 rule D Link Systems Inc 68 DVG N5402GF User s Manual ADVANCED Note E 164 Numbering depends on the proxy If you fail to make a call please contact your VoIP Service Providers ADVANCED VoIP gt SIP Advanced SESSION TIMER Session Expiration 0 0 disable 10 1500s Session Refresh Request UPDATE re INYITE Session Refresher vas uac Session Expiration This field will set the time that the VoIP Router will allow a SIP session to remain die without traffic before dropping it Session Refresh Request Select UPDATE or re INVITE to send refresh requests to the Se
44. dwidth that is less than the actual bandwidth subscribed from the drop down menu Upstream Bandwidth Select the upstream bandwidth that is less than the actual bandwidth subscribed from the drop down menu ToS IP Precedence Select the precedence for signaling data and voice voice data to tag voice packets DiffServ DSCP Select the number of signaling data and voice voice data values to tag voice packets Note For the VolP Router ToS IP Precedence and DiffServ are the same function You only select one for priority marking D Link Systems Inc 80 DVG N5402GF User s Manual ADVANCED 3 2 5 2 NAT Traversal If your VoIP Router is set up behind an Internet sharing device you can select either the NAT or STUN protocol ADVANCED Advanced Network NAT Traversal If the gateway is set up behind an Internet sharing device you can select either the NAT or STUN protocol NAT PUBLIC IP Enable NAT IP Domain STUN CLIENT Enable STUN Server IP Domain STUN Server Port Enable NAT Public IP Check the box to use the IP address of the Internet sharing device if the VolP Router is set up behind an Internet sharing device Also the VolP Router will use the IP address of the Internet sharing device as the public IP when it connects to Internet Furthermore some of the Internet sharing device s type is symmetric NAT You need to set Virtual Server or Port Mapping Forwarding from the
45. e presented with step by step instructions in order to get your Internet connection up and running Click the button below to begin Click Setup Wizard gt Setup Wizard Note Before launching the wizard please ensure you have correctly followed the steps outlined in the Quick Installation Guide included with the router This wizard will guide you through a step by step process to configure your new D Link router and connect to the Internet Step 1 Change Device Login Password Step 2 Set Time and Date Step 3 Setup Internet Connection Step 4 Line Register Step 5 Setup Wireless Connection Step 6 Setup Wireless Security Step 7 Save and Restart Click Next y Next Cancel D Link Systems Inc 9 DVG N5402GF User s Manual SETUP The factory default password of this router is admin To help secure your network D Link recommends that you should choose a new password If you do not wish to choose a new password now just click Skip to continue Click Next to proceed to next step New Password eaea Confirm Password Hkk New Password eaaa Confirm Password Hok Back Next Skip Cancel The username of ADMIN and USER have been defined and locked by default It is highly recommended to create a login password to keep your VoIP Router secure Click Next D Link Systems Inc 10 DVG N5402GF User s Manual SETUP The Time Configuration option allows you to configure update and mai
46. een a STUN server and client NAT Type Unknown STUN Server IP Domain STUN Server Port 3478 1 65535 NAT Type It shows the NAT type of your router STUN Server IP Domain Enter the IP address or URL of the STUN server for query STUN Server Port Enter the STUN Server s listening port D Link Systems Inc 82 DVG N5402GF User s Manual ADVANCED 3 2 5 4 Static Route Build static routes within an internal network These routes will not apply to the Internet ADVANCED Advanced Network Static Route This page allows you to add a specific route interface If you are not familiar with these Advanced Network settings please read the help section Route Mask Next Hop IP Interface Route Destination network of the route Route Mask Subnet mask to apply on destination network Next Hop IP The next hop IP address to the specified network Interface The interface attached to this route 3 2 5 5 UPnP ADVANCED Advanced Network UPnP Click the checkbox to enable UPnP Device MV Enable UPnP Enable UPnP Check the box to enable UPnP device on DVG D Link Systems Inc 83 DVG N5402GF User s Manual 3 2 5 6 RIP ADVANCED gt Advanced Network RIP Enable RIP Send Version Receive Version Enable Authentication Authentication Password Update Timer Timeout Timer Garbage Timer ADVANCED 30 180 120 Enable RIP Check the bo
47. efore you enable it Outbound Proxy IP Domain Enter the outbound proxy s IP address or URL Outbound Proxy Port Enter the outbound proxy s listening port SETUP VoIP Setup F Enable P Asserted Enable P Assert Check the box to enable the caller ID protection Privacy Type It is used to disguise the caller ID when queried via an ITSP Third Party Assertion The Privacy Type includes user header session none critical id and history SETUP VoIP Setup NUMBER TRANSLATION YoIP Dial Out defined here overrides Digit Map Copy From None Scan Code YoIP Dial out Add The rule of dialing of inviting to VoIP Service Providers may vary That is you have to configure different Digit Map for different VoIP Service Providers In this filed you can configure individual dialing plan for each VoIP Service Provider The following examples introduce some cases For general configuration refer to Digit Map page Note Press Add to add an entry Don t forget to press Apply which in the above of Number Translation D Link Systems Inc 26 DVG N5402GF User s Manual SETUP For example Example in Taiwan If Server 1 is local VoIP Service Provider you can refer to Digit Map page for general settings If Server 2 is global VoIP Service Provider VoIP STUN free to dial to some cities free charge you can set individual dialing plan for VoIP STUN in Numb
48. en calling to other gatewayfs Gateway Name Gateway Number IP Domain Name Port YF Gateway Name Gateway Number IP Domain Name Port Gateway Name Enter the alias of the remote peer Gateway Number Enter the phone number of the remote peer IP Domain Name Enter the IP address or URL Uniform Resource Locator of the remote peer Port Enter the listen port of the remote peer D Link Systems Inc 67 DVG N5402GF User s Manual ADVANCED 3 2 1 12 SIP Advanced ADVANCED VolP gt SIP Advanced There are many parameters that need to contact with VSP Voice Service Provider before setting up Listen Port UDP 5060 1 65535 RTP Starting Port UDP 9000 1 65500 SIP Transport Protocol UDP Listen Port UDP Enter the VolP Router s listening port in this field Leave it as default settings unless it conflicts with ports used by other device in your network RTP Starting Port UDP Enter the starting port number or transmitting voice data among VoIP devices Each line requires 2 ports For example if the starting port is 9000 then Line 1 will take up ports 9000 and 9001 and Line 2 will take up ports 9002 and 9003 and so forth SIP Transport Protocol DVG N5402GF supports UDP TCP and TLS for SIP signaling Most of SIP Server support UDP if you prefer TCP or TLS please make sure whether remote party supports TCP TLS or not ADVANCED VoIP SIP A
49. ent Router Time It shows the current time of the VoIP Router Time Zone Select your time zone from the drop down menu Enable Daylight Saving To enable disable daylight saving time Daylight Saving Offset Set the current time zone offset for your location Daylight Saving Dates Set the start and end dates for daylight saving time D Link Systems Inc 44 DVG N5402GF User s Manual ADVANCED 3 2 ADVANCED 3 2 1 VoIP 3 2 1 1 Caller Filter This function allows you to accept or reject any incoming call from the IP address listed in the filter rule The call from the IP address of SIP proxy server is always accepted despite Deny is selected or the IP address of SIP proxy server is not in the filter rule of Allow ADVANCED VolP gt Caller Filter This Function is used at allow or deny SIP Invite From the Proxy list ONLY Caller Filter Allow Apply Cancel Status Filter IP Address Subnet Mask Enable 192 165 58 21 255 255 255 0 E F Caller Filter It is to allow or deny the filter rule Status It is to show the status of enable or disable Filter IP Address Enter the start IP address which you would like to Allow or Deny Subnet mask Enter the subnet mask you would like to Allow or Deny D Link Systems Inc 45 DVG N5402GF User s Manual ADVANCED 3 2 1 2 Caller ID ADVANCED gt VolP gt Caller ID In this section it allows you to set Caller ID generation There are two type of FSK
50. er ov IG 711 udaw 64kbps v 96 96 127 200 60 1200 ms ADVANCED Switch FAX On CED Detection DVG will send FAX Re Invite immediately as it detect FAX CED tone that will save handshaking time between FAX machines Restrict T 38 DVG will reject T 38 Re invite in case the FAX type contains without T 38 FAX Detection Sensitivity To set higher value to make DVG to be more sensitive High Speed Redundancy Set redundancy packets for FAX image It could repair FAX image for non continuous packets lost The higher redundancy the higher bandwidth required Low Speed Redundancy Set redundancy packets for FAX handshaking signaling FAX Codec Select G 711 a law or G 711 u law for T 30 from the drop down menu T 30 Bypass Payload Type Fill correct payload type of T 30 bypass method FAX Jitter Buffer Enter the buffer or jitter when receiving packets Note When you send a fax over an IP network the IP network needs to support fax over IP functionality either T 38 or T 30 Please consult your VoIP Service Provider for this setting D Link Systems Inc 61 DVG N5402GF User s Manual ADVANCED 3 2 1 9 Hot Line ADVANCED gt VolP Hot Line Hot Line No Enter the hotline number for an automatic dialing Function Warm Line When the Warm Line function is in use user can dial a number Otherwise the system will divert incoming calls from an outside line to the Hot Line Number after a se
51. er Translation field Scan Code can be your dialing custom and VoIP Dial out is the number on the basis of the dialing rule needed by VoIP STUN Its dialing rule is Country code Area Code phone number When you make calls to Taipei through VoIP STUN you don t change the dialing custom just dial 02xxxxxxxx and the system will change the number from 02xxxxxxx to 8862xxxxxxxx The same rule is for 2 When you make calls to UK via VoIP STUN you ll dial 00244xxxxxx and the system will change it to 44xxxxxx The settings for Server 2 appear like NUMBER TRANSLATION YoIP Dial Out defined here overrides Digit Map Copy From None Scan Code YoIP Dial out 02 8862 00244 44 If Server 3 is a VolP Service Provider in UK you can set individual dialing plan in Number Translation field As you make calls to UK through this VoIP Service Provider Country code should be removed and plus 0 by the system The settings for Server 3 appear like NUMBER TRANSLATION YoIP Dial Out defined here overrides Digit Map Copy From None Scan Code YoIP Dial out 00244 0 D Link Systems Inc 27 DVG N5402GF User s Manual SETUP 3 1 3 Wireless Setup This section instructs you how to setup your wireless network on the VoIP Router device O setup Hint 1 Every device in the same wireless network must use the same SSID 2 To avoid wireless network overlap a specific and different channel is needed
52. g Initial Unregister Check the box to send an unregistered message initially by the VoIP Router and then it will perform a general register process Unregister All Contacts DVG N5402GF will fill a star in Contact field in un register request to release all registered accounts in this DVG N5402GF Keep SIP Auth DVG N5402GF keeps the last register SIP MD5 authentication information and re use it for next register request Support Message Waiting Indication MWI It is used to enable disable Message Waiting Indication It is available only when Voice Mail Service is available from the VoIP Service Provider MWI Subscribe Interval It is used to set the subscribe time for the VoIP Router to check the voice mail D Link Systems Inc 25 DVG N5402GF User s Manual SETUP SETUP VoIP Setup C Outbound Proxy Support Outbound Proxy Support Check the box to send all SIP packets to the destined outbound proxy server An outbound proxy server handles SIP call signaling as a standard SIP proxy server would do Further it receives and transmits phone conversation traffic media between two communication parties This option tells the VoIP Router to send and receive all SIP packets to the destined outbound proxy server rather than the remote VoIP device This helps VoIP calls to pass through any NAT protected network without additional settings or techniques Please make sure your VoIP Service Provider supports outbound proxy services b
53. he network adapter This feature can be configured to DENY network Internet access Enable MAC Filtering MAC Remark MAC Remark Enable MAC Filtering Check the box to deny from accessing Internet MAC Enter the MAC of the computer in the LAN Local Area Network to be used in the MAC filter table Remark Enter comments D Link Systems Inc 72 DVG N5402GF User s Manual ADVANCED 3 2 3 Firewall and DMZ 3 2 3 1 DMZ DMZ Demilitarized Zone allows the server on the LAN site to be directly exposed to the Internet for accessing data and to forward all incoming ports to the DMZ Host Adding a client to the DMZ may expose that computer to a variety of security risks so only use this option as a last resort ADVANCED gt Firewall and DMZ DMZ DMZ allows the server on the LAN site to be directly exposed to the Internet for accessing data Either this function or virtual server can be selected for use in accessing external services C Enable DMZ C SIP ALG C RTSP ALG Enable DMZ Check the box to enable DMZ feature DMZ Host IP Address Enter the IP address of that computer as a DMZ Host with unrestricted Internet access Note Either this function or virtual server can be selected for use in accessing external services SIP ALG Enable ALG for LAN port SIP UA RTSP ALG Enable ALG for RTSP multimedia stream D Link Systems Inc 73 DVG N5402GF User s Manual ADVANCED 3 2 3 2 D
54. her Suite WPA2 Cipher Suite is used for the configuration of WPA2 or WPA2 Mixed TKIP TKIP is the security protocol used in WPA The length of TKIP encryption is longer than WEP encryption that increases the complexity of decoding for crackers AES The most powerful encryption algorithm that is commonly used in WPA Pre Shared Key Format Select the Format of Pre Shared Key You can select Passphrase or Hex 64 characters by entering a character string ranging from A z and 0 9 Pre Shared Key Enter a key of 8 64 characters long in the Pre Shared Key filed Make sure this key is exactly the same on all other wireless stations D Link Systems Inc 32 DVG N5402GF User s Manual SETUP SETUP gt Wireless Settings gt Wireless Security WPA Use WPA or WPA2 mode to achieve a balance of strong security and best compatibility This mode uses WPA for legacy clients while maintaining higher security with stations that are WPA2 capable Also the strongest cipher that the client supports will be used For best security use WPA2 Only mode This mode uses AES CCMP cipher and legacy stations are not allowed access with WPA security For maximum compatibility use WPA Only This mode uses TKIP cipher Some gaming and legacy devices work only in this mode To achieve better wireless performance use WPA2 Only security mode or in other words 4ES cipher WPA Authentication Mode Enterprise RADIUS WPA Cipher Suite O
55. ider before enabling it Callee Quick Media DVG N5402GF will send RTP to remote party immediately as user answer an inbound call FXS Hunting For Unknown Number Select the response for an incoming call which the called number is not exist in on the DVG Disable DVG responses 404 not fornd Hunt and Transit Dial DVG sends alert to an available FXS port and dial the number to PBX as the FXS port picked up by PBX It works with SoftSwitch or IPPBX to allow a remote client reach the PBX extension for one step dial For virtual extension FXS Group Hunting Ring Type DVG sends alert to an available FXS port for hunting group Support URI Percent Encoding RFC 3986 Check the box to encode decode the letters of the basic Latin alphabet digits and a few special characters which follow RFC 3986 Call Hold Compatible With RFC 2543 It is used to set the procedure of Call Hold being compatible with RFC 2543 D Link Systems Inc 71 DVG N5402GF User s Manual ADVANCED 3 2 2 Access Control 3 2 2 1 MAC Filtering Use MAC Filters to deny computers within the local area network from accessing the Internet You can either manually add a MAC address that are connected to the VoIP Router ADVANCED Access Control MAC Filtering The MAC Media Access Controller Address Filter option is used to control network access based on the MAC Address of the network adapter 4 MAC address is a unique ID assigned by the manufacturer of t
56. ink Systems Inc 98 DVG N5402GF User s Manual MAINTENANCE 3 3 8 CDR The user can set up a CDR Server to record call details for every phone call with TCP protocol The present CDR provides the call event such as HOOK ON HOOK OFF DIALED NUMBER DATE recording in a text file and which can be imported to prepare an analysis report MAINTENANCE gt CDR The user can set up a CDR Server to record call details for every phone call with TCP protocol The present CDR provides the call event such as HOOK ON HOOK OFF DIALED NUMBER DATE recording in a text file and which can be imported to prepare an analysis report C Send record to CDR Server Send record to CDR Server Tick the check box to enable the call detail recording CDR Server IP Domain Enter the IP address of the CDR server Port Enter the listen port of the CDR server RADIUS Enter the information of RADIUS needed It includes RADIUS Accounting Port RADIUS Server Secret RADIUS User ID and RADIUS Password D Link Systems Inc 99 DVG N5402GF User s Manual 3 4 STATUS 3 4 1 Device Info STATUS Device Info All of your Internet and network connection details are displayed on this page The firmware version is also displayed here SYSTEM INFORMATION WAN PORT INFORMATION Factory Default MAC Address Net Link IP address Subnet mask Default Gateway Domain Name Server LAN PORT INFORMAT
57. it is used for peer to peer connect mode Channel Width Wireless channel width for 802 11n Select 40 MH for higher speed Broadcast SSID Broad AP s SSID for convent usage To hid SSID for more security Enable WMM Wi Fi Multimedia It provides higher priority for multimedia stream to get better quality Enable Universal Repeat Mode Set DVG N5402GF to be wireless repeat mode Please fill the same SSID as the root AP in SSID of Extended Interface SETUP gt Wireless Setup gt Wireless Basic MULTIPLE AP Enable 802 11 Mode Broadcast SSID Enable WMM Access E nbw LAN WAN niw LAN WAN v ngo v LAN WAN nbw i LAN WAN Multiple AP It is used for different level of clients Such as different departments or guests And you could assign different password for each SSID D Link Systems Inc 29 DVG N5402GF User s Manual SETUP 3 1 3 2 Wireless Security This section introduces you different ways of wireless security you can setup It is important to enable secure algorithm to protect your data from eavesdropping by unauthorized wireless users SETUP gt Wireless Setup gt Wireless Security To protect your privacy you can configure wireless security features This device supports three wireless security modes including WEP WPA WPA2 and WPA2 Mixed WEP is the original wireless encryption standard WPA provides a higher level of security Select SSID Root AP dlink w WIRELESS SECURITY M
58. l act like TCP ie every packet sent will receive an ACK to make sure that packet sent has been received by other peer Compact Form Check the box to represent common header field names in an abbreviated form This may be useful when SIP message is too large to be carried on and recognized by the user agent SIP Caller ID Obtaining Select the part of the SIP packet from the VoIP Gateway to obtain Caller ID There are several places where the Caller ID is located D Link Systems Inc 70 DVG N5402GF User s Manual ADVANCED Remote Party ID Display Name It is located at SIP Remote Party ID Before lt sip Remote Party ID User Name It is located at SIP Remote Party ID After lt sip Before From Header Display Name The standard way is in SIP Message Header gt From gt SIP Display info From Header User Name It locates at SIP gt Message Header gt From gt SIP from address before Put Caller ID In URI This feature is to put Caller ID in URL The Caller ID is located in SIP Message Header gt After From Before lt sip by default settings It will be located in SIP gt Message Header gt After lt sip Before if ticked INVITE With Remote Party ID Header Check the box to comprise the information of Remote Party ID in the message header of INVITE Different format of INVITE header might cause the call not to be connected Please consult with your VoIP Service Prov
59. ld music to the remote end Meanwhile the local user can dial out another number after the dial tone is heard After the handset is on hooked the call originally on hold will then be transferred to the new number regardless the status of the new call If wrong number is dialed for the new call press the FLASH button will switch back to the call on hold Also if the local user doesn t hang up the phone after the new call is set up press the FLASH button will switch between the original call and the new call Please note that the PBX between phone sets and the VoIP Router must support FLASH features in order to use this function If a phone set is connecting directly to the FXS port of the VoIP Router and the FLASH button does not function please adjust the settings in Flash Detect Time from Advanced Options section Note The availability of the above features also depends on your VoIP Service Provider Please also check with your service provider for these services Examples of establishing a Three Way call 1 Phone dials to Phone2 Phone2 answers the call 2 Phone presses Flash then calls Phone Phonez2 is on hold and Phone3 answers the call 3 Phone presses Flash to start the conference call Or 4 Phone dials to Phone2 Phone2 answers the call 5 Phone presses Flash then calls Phones Phoned is on hold and Phone3 answers the call 6 Phone presses Flash and dial 3 to start the conference call Note The a
60. less security features This device supports three wireless security modes including WEP WPA PSK and WPA WEP is the original wireless encryption standard WPA provides a higher level of security WPA PSK does not require an authentication server The WPA option requires an external RADIUS server Wireless Security Mode None v Select Security Mode for your wireless network Click Next D Link Systems Inc 14 DVG N5402GF User s Manual The last step is to save changes and restart Gateway to make new settings effective Save and Restart takes about 40 seconds The login page will show in about 1 minute SETUP SUMMARY Below is a detailed summary of your settings Please print this page out or write the information on a piece of paper so you can configure the correct settings on your wireless client adapters Time Settings Enable Protocol DHCP Proxy Server IP Domain 192 168 1 1 Proxy Server Port 5060 SIP Domain Phone 1 FXS Number 701 Phone 2 FXS Number 702 Wireless Network Name SSID dlink Wireless Channel Auto Scan recommended 802 11 Mode Mixed 802 119 and 802 11b Wireless Security Mode None Setup is finished Check the summary of your settings To make new settings effective you must click on the Restart button to reboot the DVG N5402GF Click Restart D Link Systems Inc SETUP 15 DVG N5402GF User s Manual SETUP 3 VoIP Router Web Configu
61. ll be used with the IP address that will be blocked Remark Enter comments D Link Systems Inc 75 DVG N5402GF User s Manual ADVANCED 3 2 3 4 Port Filtering Port filtering enables you to control all data that can be transmitted over routers When the port used at the source end is within the defined scope it will be filtered without transmission ADVANCED gt Firewall and DMZ Port Filtering Some applications require that specific ports in the Router s firewall be opened for access by the remote parties Port Filtering opens up the Open Ports in the Firewall when an application on the LAN initiates a TCP UDP connection to a remote party using the Port Filtering Enable Port Filtering Port Range TCP UDP Remark Port Range TCP UDP Remark Enable Port Filtering This variable is to restrict certain types of data packets by port Port Range Enter the port range that will be denied access to the Internet TCP UDP Select TCP UDP or Both that will be used with the port that will be blocked Remark Enter comments D Link Systems Inc 76 DVG N5402GF User s Manual ADVANCED 3 2 3 5 Virtual Server Enable users on Internet to access the WWW FTP and other services from your NAT It is also known as port forwarding When remote users are accessing Web or FTP servers through WAN IP address it will be routed to the server with LAN IP address ADVANCED gt Firewall and DMZ Virtual Se
62. llow all 802 116 compliant wireless devices to associate with the wireless AP 802 11g only Allow all 802 11g compliant wireless devices to associate with the wireless AP D Link Systems Inc 28 DVG N5402GF User s Manual SETUP 802 11n only Allow all 802 11n compliant wireless devices to associate with the wireless AP Mixed 802 11g and 802 11b Allow a mix of both IEEE802 11g and 802 11b compliant wireless devices to associate with the wireless AP Mixed 802 11n and 802 11g Allow a mix of both IEEE802 11n and 802 11g compliant wireless devices to associate with the wireless AP Mixed 802 11n 802 119 and 802 11b Allow a mix of both IEEE802 11n 802 11g and 802 11b compliant wireless devices to associate with the wireless AP Access Mode DVG N5402GF has ability to serve as two operating modes in wireless network separately AP As a wireless AP that allows wireless equipped stations to communicate with a wired network and the other wireless network for Internet access and resources sharing Client As a wireless client you are allowed to access Internet via an Access Point in infrastructure mode or build a group of wireless network for files and printer sharing in ad hoc Mode Under Wireless Client Mode Bridge Mode is not available for the VoIP Router Network Type Select network type for Access Client Mode Infrastructure Connect to another wireless AP or WISP Ad hoc Connect to another wireless Ad hoc device Usually
63. n menu to adjust the speaking volume Tone Volume Use the drop down menu to adjust the tone volume It will apply to all tones generated by the VolP Router including Dial Tone Ring Back Tone and Busy Tone Min FXS Hook Flash Time Enter the minimum flash time for FXS detecting When the flash signal generated by the phone set is shorter than Min FXS Hook Flash Time FXS port will be on hook Flash Time Enter the maximum flash time for FXS detecting When the flash signal generated by the phone set is longer than the Flash Time FXS port will be on hook Polarity Reversal Check the box to activate the generation of polarity reversal from FXS FXS Chip Option 1 Check the box to avoid mis detecting the loop state of a subscriber line or PBX user loop from FXS interface In some cases the off hook voltage might cause the FXS interface mis detect the idle and the active state in order to avoid this situation un check this feature FXS Current Set the output D C current of FXS port D Link Systems Inc 63 DVG N5402GF User s Manual ADVANCED ADVANCED VolP gt Line Ring Early Media Time Limit 10 600s C Enable End of Digit Tone Force Calling Thru PSTN Code Early Media Treatment Loop Current Drop Trigger PEERS O disable 3 30s Loop Current Drop Duration 1 5s ROH Begin Time I 0 disable 1 999s ROH Duration ic FXS Ring Voltage 45 80 FXS Onhook Voltage 24 57 VoIP Cent
64. need user phone Reliability of Provisional Responses LI LI Compact Form SIP Caller ID Obtaining Remote Party Id Display Name C Put Caller ID In URI C INVITE With Remote Party ID Header Callee Quick Media Disable FXS Hunting For Unknown Number Disable C Support URI Percent Encoding RFC 3986 Call Hold Compatible With RFC 2543 Anonymous Caller ID CLIR Check the box to lock the delivery of the Caller ID to the called party VoIP Call Out Notification Check the box to enable the function of playing a tone to notify user that the call is through VoIP Enable Built in Call Hold Music Check the box to enable the function of playing music when receiving Call Hold request Call On Hold Notification FXS will send alert to phone set as users hang up if there is a call still held in another line Enable Non SIP Inbox Call Check the box to make local calls Local Call here means the call does not go through the Internet and if the dialed number is the extension of other line You can un check it to configure as all calls go through the Internet Invite URL need user phone Check the box to add user phone as a hint that the part left to the sign is actually a phone number Reliability of Provisional Responses Check the box to send a PRACK request during the progress of the request processing Reliability of Provisional Responses is to ACK at every SIP packet With this method SIP packet wil
65. nslation table Translate the global number to private number bated on Number Translation table Dial out as defined in the first match case by VoIP Router D Link Systems Inc 111 DVG N5402GF User s Manual Appendix 5 3 Routing To achieve maximum flexibility the number dialed will be looked up in several tables defined by VoIP Router If no match is found from Digit Map Table it will then look up the number from another table and to the registered VoIP Service Provdier Routing Processing Flow The routing after checking Digit Map Table may be vary The routing accords with VoIP Route Profile By default Phone Book is the first route of VoIP Route Profile The second and third route is Server 1 and Server 2 Server 3 is the last route Each server has a dialing plan i e number translation table and the number will be translated according the dialing plan before dialing out For default setting the number look up flow appears like Digit Map Phone Assume that the route of Default Route Profile is Server 2 as the first route Server 3 as the second route and Server 1 as the last route The number look up flow appears like Digit Map l D Link Systems Inc 112 DVG N5402GF User s Manual Appendix Start Enter a phone number D Is D defined in Digit Map table Change the number to Yes Global Number No s D or Global Numbe defined in Phone Book
66. nsmits voice data packets via the Internet hence the condition and status of the network environment is relatively important to the telecommunications quality If any one of the parties involved in VolP communications has insufficient bandwidth or frequent packet loss the telecommunication quality will be poor Therefore excellent telecommunication can only happen when the VoIP Routers are connected to the Internet and when the network environment is stable 4 1 Preparation 1 Connect the power supply telephone set telephone cable and network cable properly 2 Ifa static IP is provided confirm the correct IP settings of the WAN Port IP address Subnet Mask and Default gateway Please contact your local Internet Service Provider ISP if you have any question 3 If you are using ADSL PPPoE for your network connection confirm the account number and password 4 If you intend to operate the VoIP Router under NAT the IP range of VolP Router WAN Port and LAN Port IP Address should not be the same in order to avoid phone failures Basic Setup The VoIP Router provides two setup modes 1 Telephone IVR Configuration Mode 2 Browser Configuration Mode IVR configuration provides basic query and setup functions while browser configuration provides full setup functions IVR Interactive Voice Response The VoIP Router provides convenient IVR functions Users are able to get query and setup the VoIP Router with a phone set
67. ntain the correct time on the internal system clock From this section you can set the time zone that you are in and set the NTP Network Time Protocol Server TIME SETTINGS V Automatically synchronize with Internet time servers First NTP time server ntp1 diink com Second NTP time server ntp dlink com tw TIME CONFIGURATION Current Router Time 2008 12 18 17 23 46 Time Zone GMT 12 00 International Date Line West Enable Daylight Saving Daylight Saving Offset o 00 z Month Week Day Time Daylight Saving Dates Start Jan ist Sun z 12 am End Jan r ist Sun r 12 am z Back Next Cancel Enter a NTP server or use the default server Select your time zone from the drop down menu Enable Daylight Saving for your local time if required Click Next D Link Systems Inc DVG N5402GF User s Manual SETUP Use this section to configure your Internet Connection type If you are unsure of your connection method please contact your Internet Service Provider DHCP Static IP PPPoE PPTP 3G USB Adapter Advanced Configuration WAN 1 SETTINGS Hostname Vendor Class ID MTU 1500 WAN 1 Domain Name Server Domain Name Server Primary IP 168 95 1 1 Domain Name Server Secondary IP WAN LINK SPEED WAN Link Speed Auto WANI Factory Default MAC Address 00 08 2C 11 22 33 Your MAC Address 00 0A 79 60 17 28 Cur
68. o pd ot Disturb 74 H J as Unconditional Forward 77 J J Busy Forward H J oO No Answer Forward Call Hold Call Transfer J _ Call Waiting H J m s a go 76 76 js 75 a ae a T Local Mixer Call Pickup Call Back on Busy Blind Transfer Enable Call Feature Code Check the box to enable disable some call feature codes through a phone set Call pickup Allow one to pick up someone else s telephone call Call Back on Busy Your phone will ring back the last number that called you Blink Transfer Blind Transfer involves passing a call without notifying the recipient Call Feature Code Instructions example 1 If you would like to enable DND function of FXS pick up the phone connected to FXS and dial 74 2 If you would like to enable Unconditional Forward of FXS and assign the number pick up the phone and dial 77 0912345678 0912345678 is the number which the incoming call is forwarded to 3 If you would disable Unconditional Forward of FXS pick up the phone and dial 77 D Link Systems Inc 48 DVG N5402GF User s Manual ADVANCED Calling Feature Instructions Call Hold The call will be held after the FLASH button is pressed on the phone set The VoIP Router will play a hold music provided by your ITSP or VSP to the remote end Call Transfer The call will be held after FLASH button is pressed on local phone set the VolP Router plays on ho
69. oIP call If you dial VoIP Centrex Digit first the dialing plan is according to the Digit Map otherwise the VoIP Gateway will send the number which digit count is the same as VoIP Centrex Extension Digit Count Metering Pulse Type Metering Pulse Period It is used for telephony device which connected to FXS port for billing purpose DVG N5402GF provide 14k Hz and 16k Hz metering capacity The fully support for detail Metering Pulse Period is not free charge please contact with your vendor D Link Systems Inc 64 DVG N5402GF User s Manual ADVANCED ADVANCED gt VolP Line TERMINATION IMPEDANCE FXS Impedance Taiwan 600 Ohm FXS Impedance Select different impedance from the drop down menu ADVANCED gt VolP Line VOICE MENU OPTIONS Silence Detection Threshold o P O disable 1 60 db Drop Silent Call Timeout 120 O disable 1 3600 5 This feature is a call drop standard for a VolP Router to determine whether or not to hang up the phone The VolP Router will disconnect the call automatically to avoid keeping the line engaged if the detected volume is below the Silence Detection Threshold or the time exceeds the Drop Silent Call Timeout Silence Detection Threshold Enter the threshold dB to detect if there is voice coming from RJ 11 interface Drop Silent Call Timeout Enter the duration second for detecting if there are RTP packets receiving from RJ 45 interface Note Improper values for ab
70. oS Prevention ADVANCED gt Firewall and DMZ DoS Prevention This allows you to prevent you router from Denial of Service DOS attacks DoS can be checked based on your specific need Enable DoS Protection WHOLE SYSTEM FLOOD so Packets Second 50 500 TCP Scan Ping of Death ICMP Smurf IP Spoof Ow Oo Enable DoS Prevention Check the box to prevent DoS attacks from WAN or LAN There are various types of DoS attacking Leave settings in this field to the default if you are not familiar with it D Link Systems Inc 74 DVG N5402GF User s Manual ADVANCED 3 2 3 3 IP Filtering Use IP Filters to deny particular LAN IP addresses from accessing the Internet You can deny specific port numbers or all ports for a specific IP address The screen will display well known ports that are defined To use them click on the edit icon You will only need to input the LAN IP address es of the computer s that will be denied Internet access ADVANCED gt Firewall and DMZ IP Filtering The IP Filter option is used to control network access based on the IP of the network device This Feature can be configured to DENY network Internet access Enable IP Filtering TCP UDP Remark IP TCP UDP Remark Enable IP Filtering Check the box to deny particular LAN IP addresses from accessing the Internet IP Enter the IP address that you want to deny in this filed TCP UDP Select TCP UDP or Both that wi
71. oemawaecan 93 OO DANOS liG S ac ccta siete ihe a iam T E tw vila uineraihetuiaine onic acta noaieiwaw neu T 94 BO ROGI wage eehetese tiara rete T et ute sn atl betes a Pied ated E E hea el aie Leg 97 J3 GODA srine a Divo tuners a ale w eee Weim sible ows A wanton owen Ce eae tunes 99 FASTA RU a toa aera nae ah ua eee E Pel encaate EAE A AA E aaden cates 100 BHAA DEVICE IMO aerer ones EE A ENNE E E EEEE ENEE A E E te etilevewes 100 2s WOVE SLALUS ia a peri startup A AAS A ES 101 SAS ELAN GIEN eaor oS aie as sco viniweecisiaiey tee arcana ne aie awn wrhoie wig aioe aiccew Biv vale atte oa eae sie aden wade 102 AA LUIS ICS oral EE tera tn m rele cacestain E E ao Sy le Vacs E E E E 103 gA o Roumo TADE eaaa anions E en aie seit asl E ule manish a aa 103 FAC LOGOUT dur E actos A E E E erent 104 4 Configuring the VoIP Router through IVR ssssessessseeseessecssecssscsseosecosecssecesscseecsecoseeeseeeo 105 AT IVR N eractive VOICES RESPONSE Yc eixs woes e AA dene R E E 105 A 2 IP Coniooration oS MNOS maree e E E A eciaeedceeuaadceesus sade 108 9 Dialing Principle S easan aa a a E E E R aa 111 Ol DIAN OPON S eert a a A E E A E teen dat A AA 111 S Z NUMDE TRANSIAMOM wxivecrvs diversas E AE A EE EAE A E a E 111 5 3 ROUMO iain tut aia eve i a AOF A ATE EE E TAS 112 fal ol 91 11 b oai E E E E ene ee rate sree 114 Produc PEATEs merrier teed cree idee nearuus a aren ede eet kde noranem ee hess ees arenas tes 114 DVG N5402GF User
72. on IVR 4 2 IP Configuration Settings Set the IP Configuration of the WAN Port Static IP Settings Note Complete static IP settings should include a static IP option 1 under 114 IP address 111 Subnet Mask 112 and Default Gateway 113 Please contact your Internet Service Provider ISP if you have any question Function Command Select a Static IP e After entering IVR mode dial 114 e When voice prompt plays Enter value dial 1 to select static IP IP address Settings e After entering IVR mode dial 111 When voice prompt plays Enter value enter your IP address followed by Example If the IP address is 192 168 1 200 dial 192 168 1 200 Subnet Mask Settings e After entering IVR mode dial 112 When voice prompt plays Enter value enter your subnet mask followed by Example If the subnet mask value is 255 255 255 0 dial 255 255 255 0 Default Gateway Settings After entering IVR mode dial 113 When voice prompt plays Enter value enter your default gateway s IP address followed by Example If the default gateway is 192 168 1 254 dial 192 168 1 254 Save Settings and Restart To save settings dial 509 Save Settings The system will save the current settings Please restart the system Wait for about 40 seconds for the system to restart and then enter 101 to check whether the IP address was retained If the system does not play back the IP address after dialing 101
73. on to configure your Internet Connection type If you are unsure of your connection method please contact your Internet Service Provider DHCP Static IP PPPoE PPTP 3G USB Adapter Advanced Configuration SETUP Internet Setup WAN 1 SETTINGS Hostname Vendor Class ID MTU WAN 1 Domain Name Server Domain Name Server Primary IP Domain Name Server Secondary IP 1500 Manual v 168 95 1 1 SETUP DHCP Select this option if your ISP Internet Service Provider provides you an IP address automatically Cable modem providers typically use dynamic assignment of IP Address The Host Name field is optional but may be required by some Internet Service Providers SETUP Internet Setup WAN 1 SETTINGS IP address Subnet mask Default Gateway IP MTU Domain Name Server Primary IP Domain Name Server Secondary IP 192 168 1 2 255 255 255 0 192 168 1 254 1500 168 95 1 1 Static IP Select this option if your ISP Internet Service Provider provides you a Static IP address Enter the IP address Subnet Mask and Default Gateway IP D Link Systems Inc 17 DVG N5402GF User s Manual SETUP Internet Setup WAN 1 SETTINGS PPPoE Account PPPoE Password Confirm Password PPPoE Service Name MTU WAN 1 Domain Name Server Domain Name Server Primary IP
74. ort for the SIP in this field Leave this field to the default if your VoIP Service Provider did not give you a server port number for SIP Proxy Server Realm Enter the realm for SIP proxy server It is used for authentication in a SIP server In most cases the VoIP Router can automatically detect your SIP server realm So you can leave this option blank However if your SIP server requires you to use a specific realm you can manually enter it in TTL Registration interval 10 7200 s Enter the desired time interval at which the VoIP Router will report to your SIP proxy server SIP Domain Enter the SIP domain provided by your VoIP Service Provider Note some SIP proxy servers might not require this If you enable Uses Domain to Register the VoIP Router will register to the SIP proxy server with the domain name you filled in Otherwise the VoIP Router will register to a SIP proxy server with the IP it resolves Use Domain to Register Check the box to use Domain to register with SIP proxy server The VolP Router is registered to the SIP proxy server with IP address if un ticked Note Proxy Server Realm SIP Domain and Use Domain to Register are the parameters provided by VoIP Service Provider If you fail to make a call please contact your VoIP Service Provider Bind Proxy Interval for NAT Check the box to keep the binding exist by sending packets when the VoIP Router is behind a NAT and SIP proxy server is not able to keep the bindin
75. ove settings might cause unexpected automatic disconnection of a call Default values are recommended D Link Systems Inc 65 DVG N5402GF User s Manual ADVANCED ADVANCED gt VolP Line VOICE MENU OPTIONS V Enable IVR Option Enable IVR Option Check the box to enable IVR function ADVANCED gt VolP Line FXS GROUP HUNTING RING PRIORITY Hunting Ring Hunting Sequential Ring Time 6 1 100s Hunting Ring It is used to set FXS group hunting mode There are Hunting Simultaneous Ring and Sequential Ring Hunting When someone calls in by dialing FXS representative number the system will always assign the call to the first line Simultaneous Ring When someone calls in by dialing FXS representative number all FXS ports will ring at the same time Sequential Ring When someone calls in by dialing FXS representative number the system will assign the call to each FXS ports in order according Sequential Ring Time You can adjust Sequential Ring Time for the ring time of each port D Link Systems Inc 66 DVG N5402GF User s Manual ADVANCED 3 2 1 11 Phone Book Phone Book It is used for peer to peer communication Some peer information needs to be added to this section prior to making peer to peer calls You need to enter the phone number and the IP address of the remote peer ADVANCED VoIP Phone Book It has 100 phone numbers to restore into a phone book and provides an IP address query wh
76. please tick this item Test Click start to test ACO Clear alarm indication of the last test result D Link Systems Inc 95 DVG N5402GF User s Manual MAINTENANCE 3 3 6 3 FXS Inward Self Test MAINTENANCE gt Diagnostics gt Inward Test FXS Inward Self Test Ringer Loopback SLIC DC Power Tip Ring DC Analogue Voltage Feed C Enforced Test Ignore Port State It allows operator to verify if it is some problem on the FXS chip set Enable Select the lines you want to test Including Channel In Used Since the line test will interrupt a talking call that DVG N5402GF will ignore the in used line If you would like to test all the lines you select even it is in used please tick this item Test Click start to test ACO Clear alarm indication of the last test result D Link Systems Inc 96 DVG N5402GF User s Manual MAINTENANCE 3 3 7 TRO69 TRO69 allows operator to manage DVG N5402GF with a TRO69 standard protocol Note Fill in the parameters needed by your VoIP Service Provider Please check with your VoIP Service Provider about the availability of these services Advanced Settings TRO69 WAN Management Protocol TR 069 allows a Auto Configuration Server ACS to perform auto configuration provision collection and diagnostics to this device C Enable TRO69 User Name Password COT Confirm Password pe Auto Config Server URL Periodic Inform Enable
77. r s Manual SETUP Wait for Windows 7 setting up wireless network Setting up ChangThird WIN7E_Network Configuration finished you could connect to DVG N5402GF at present You could also print security key of save this profile for another computer to add this wireless network manually ChangThird WIN7E_Network has been successfully set up To add an older wireless device to this network you might need to provide this security key You can print these network settings for future reference For gaming consoles or computers running Windows XP copy the network profile to a USB drive for ATTE ee ee ee OE a ee eee easier set up Note DVG N5402GF supports WPS work with WindowsR Vista and Windows 7 only D Link Systems Inc 39 DVG N5402GF User s Manual SETUP 3 1 4 LAN Setup SETUP LAN Setup This section allows you to configure the local network settings of your VoIP Router Please note that this section is optional and you should not need to change any of the settings here to get your network up and running LAN Port Address 192 168 8 254 Subnet mask 255 255 255 0 LAN Port Address Enter the LAN IP address of the VoIP Router It is also the default gateway for DHCP clients Subnet Make Enter the subnet mask for DHCP clients D Link Systems Inc 40 DVG N5402GF User s Manual SETUP SETUP LAN Setup DHCP SERVER Enable DHCP Server IP Pool Starting Address 192 168 8 1
78. r Proxy Server IP Domain and Port Outbound Proxy Support is optional To register please click on the Outbound Proxy Support box and enter Outbound Proxy IP Domain and Port in it Registration by phone line Enter Number User ID Account and Password supplied by your ITSP Check on the Register box to register to Proxy Server Click Next D Link Systems Inc 13 DVG N5402GF User s Manual SETUP Use this section to configure the wireless settings for your D Link VoIP Router Please note that changes made on this section may also need to be duplicated on your Wireless Client Enable Wireless LAN Interface Wireless Network Nanje SSID dlink Wireless Channel Auto Scan recommended 802 11 Mode Mixed 802 119 and 802 11b Mode AP w Click on the Enable wireless LAN interface check box to build a wireless network Enter the SSID to name your wireless network All devices must have the same SSID to communicate on the wireless network Select a clear wireless channel Select the 802 11 Mode of your network which can work in different speed of wireless connection Click Next To protect your privacy you can configure wireless security features This device supports three wireless security modes including WEP WPA WPA2 and WPA Mixed WEP is the original wireless encryption standard WPA provides a higher level of security WIRELESS SECURITY MODE To protect your privacy you can configure wire
79. ration 3 1 SETUP 3 1 1 Internet Setup WAN Wide Area Network Settings are used to connect to your ISP Internet Service Provider The WAN settings are provided to you by your ISP and oftentimes referred to as public settings Please select the appropriate option for your specific ISP IP Configuration Setting WAN Port There are five methods of obtaining a WAN port IP address DHCP which means a Dynamic IP Cable Modem Static IP PPPoE dial up ADSL PPTP 3G USB Adapter Methods for using DHCP and PPPoE for obtaining an IP address may vary If you are not familiar with creating a network connection please contact your local ISP CV a After selecting the suitable option click Accept at the bottom of the screen to save the settings You need to save the changes and restart the VoIP Router to make the changes active Saving the settings Click MAINTENANCE and select Save Restart in Backup and Restore from the left menu Tick Save Settings and Restart and then click Accept Wait for about 40 seconds before the VoIP Router obtaining an IP address by the method you selected Note When the system has obtained a new IP address and you are using a WAN port to enter the Web Configuration Screen the new IP address has to be used before you can get connected to the VoIP Router The same principle applies to the next two settings D Link Systems Inc 16 DVG N5402GF User s Manual SETUP Internet Setup Use this secti
80. rent MAC Address XXIXXIXXIXX XX EXX Select your Internet connection type DHCP Most Cable ISPs or if you are connecting the DVG N5402GF behind a router Static IP Select if your ISP supplied you with your IP settings PPPoE Most DSL ISPs PPTP Select if required by your ISP 3G USB Adapter Select it for 3G WISP WAN1 Domain Name Server Select Manual to manually enter IP address of DNS or select Auto if DNS is assigned by ISP Click Next D Link Systems Inc 12 DVG N5402GF User s Manual SETUP The VoIP Router can invite register to a VoIP trunk gateway or register by each port of phone Please contact your ITSP SOFT SWITCH SETTING Enable Support of SIP Proxy Server Soft Switch ITSP Name SIPVoIP PHONE 1 FXS Number Register Invite with ID Account User ID Account Password eecccceeee Confirm Password pesececeee PHONE 2 FXS Number Register Invite with ID Account User ID Account Password CTT Confirm Password CO SIP PROXY SERVER Proxy Server IP Domain sip voip voip Proxy Server Port 5060 1 65535 Proxy Server Realm TIL Registration interval 600 10 7200s SIP Domain Use Domain to Register OUTBOUND PROXY SUPPORT C Outbound Proxy Support ma Register to the SIP Proxy Server by clicking Enable support of SIP Proxy Server Ente
81. rex Extension Digit Count VoIP Centrex Digit O disable 1 30 Metering Pulse Type Metering Pulse Period 0 Ring Early Media Time Limit 10 600secs Enter the timeout to cancel a call if no one answers the phone Enable End of Digit Tone Check the box to activate the function of playing a Beep Beep tone to notify the user that the call is in progress Early Media Treatment Check the box to send the one way RTP immediately when a connection with a VoIP service provider has been set up Loop Current Drop Trigger Time Enter the time to avoid the line being engaged when FXS port is connected to PBX It stops the loop current from FXS port when FXS port is playing busy tone The setting 0 zero is to disable this function Loop Current Drop Duration Enter the drop duration for loop current ROH Begin Time As users forget hang up phone set it makes FXS play loud Howler Tone to notify users put hand set correctly If this timer is set to be 20 seconds that FXS play busy tone for 20 seconds then play ROH ROH Duration It is the maximum time for FXS play ROH then FXS will stop play ROH and keep silence FXS Ring Voltage It is to set the Ring Voltage of FXS FXS Onhook Voltage It is to set the idle Voltage of FXS VoIP Centrex Extension Digit Count This feature is to enable and set the digit count of VoIP Centrex The setting 0 zero is to disable this function VoIP Centrex Digit Enter the digit for V
82. rver Session Refresher This determines which side of an expired call session will initiate the session refresh uac specifies that the Caller side will initiate the session refresh uas specifies that the Call receiver the Callee will initiate the session refresh ADVANCED VoIP SIP Advanced SIP TIMEOUT ADJUSTMENT SIP Message Resend Timer Base Max Response Time for Invite 1 32 SIP Message Resend Timer Base Select the resend timer base from the drop down menu if response is not received within the base time The sequence of sending is like base time 2 and send again at base time 2 2 The maximum resend time is four seconds Resend action will stop when the total resend time has reached 20 seconds Max Response Time for Invite Enter the maximum response time for INVITE packet When the destination does not reply within the set time the call is failed ADVANCED VoIP gt SIP Advanced C oIP Failure Announcement VolP failure announcement Check the box to play a voice announcement if the VolP Router fails to register to the SIP proxy server while FXS is off hook D Link Systems Inc 69 DVG N5402GF User s Manual ADVANCED ADVANCED gt VoIP SIP Advanced SUPPLEMENTARY FEATURES Anonymous Caller ID CLIR VoIP Call Out Notification S Enable Built in Call Hold Music Call On Hold Notification Enable Non SIP Inbox Call Delay PSTN Hangup Detection Invite URL
83. rver The Virtual Server option allows you to define a single public prot on your router For redirection to an internal LAN IP Address an Private LAN port if required This feature is useful for hosting online services such as FTP or Web Servers V Enable irtual Server Apply Cancel Lan Host IP Server Port Heniek Address Range Add WAN Port Range TCP UDP WAN Port Range lt TCP UDP Both LAN Host IP Address Server Port Range r Remark Enable Virtual Server Check the box to enable port forwarding WAN Port Range Enter the port range for the WAN side TCP UDP Select the communication protocols used by the server TCP UDP or Both LAN Host IP Address Enter the IP address of the device that provides various services Server Port Range Enter LAN side server port range Remark Enter comments D Link Systems Inc 77 DVG N5402GF User s Manual ADVANCED 3 2 4 Advanced Wireless 3 2 4 1 Advanced This section introduces advanced configuration for the wireless access point If you are not familiar with the following functions keep the default parameters In some cases incorrect settings may reduce wireless performance ADVANCED gt Advanced Wireless gt Advanced Allows you to configure advanced features of the wireless LAN interface Fragmentation 2346 256 2346 RTS Threshold 2347 0 2347 RF Output Power 100 Fragmentation A packet can be fr
84. s Enable Dynamic DNS Check the box to enable DDNS function It is only necessary when the VoIP Router is set up behind an Internet sharing device that uses a dynamic IP address and does not support DDNS Server address Select a DDNS service from the drop and down arrow Hostname Enter the URL of the system or NAT applied from domain name registration providers e g www dyndns org Username or Key Password or Key Enter the Login ID and password used to log in to the DDNS server Note If the VoIP Router is set up under NAT then enter the hostname in the NAT IP Domain that is the same as the Hostname of the DDNS D Link Systems Inc 92 DVG N5402GF User s Manual MAINTENANCE 3 3 5 Log Settings MAINTENANCE gt Log Settings The System Log options allow you to send log information to a SysLog Server Enable Enable Check the box to send event notification messages across IP networks to the Server Server Address Enter the System Log Server s IP address Port Enter the System Log Server s listening port Leave this field to the default if your VoIP Service Provider did not provide you a server port number for System Log Server D Link Systems Inc 93 DVG N5402GF User s Manual 3 3 6 Diagnostics 3 3 6 1 Ping Test MAINTENANCE Use Ping to verify if a remote peer is reachable Enter a remote IP address and click Test to ping the remote host The result woul
85. s the time interval for the VoIP Gateway to send a RTP packet or voice packet to the receiving side The smaller the value the greater the bandwidth takes and larger values might cause voice delay Approximate Bandwidth Required It shows the bandwidth required from different codec and packet interval D Link Systems Inc 50 DVG N5402GF User s Manual ADVANCED 3 2 1 5 CPT Cadence ADVANCED VoIP gt CPT Cadence CPT 1 Default Low High Frequency Frequency Tone Type T_ON_1 3000 Dial Tone 350 Congestion 480 440 TANA 620 250 Busy Tone 480 620 500 Ring Back 4s0 1o00 Tone 440 bey tsa CPT 1 Enable Setting 1 Define the call process tones for the DVG N5402GF generates ADVANCED VoIP CPT Cadence FXS Ring Cadence Default Settings Sakuna OFF_1 ON_2 OFF_2 ON_3 OFF_3 250 8000 0 250 0 250 0 250 0 250 ms 8000 ms 8000 ms 8000 ms 8000 ms N_1 Range ON ge 250 8000 ms 200 o FXS Ring Cadence Settings Specify the ring cadence for the FXS port In this field you specify the on and off pulses for the ring The ring cadence that should be configured differs depending on local PSTN or PBX settings and requirements D Link Systems Inc 51 DVG N5402GF User s Manual ADVANCED 3 2 1 6 Digit Map Digit Map supports multiple dial plans which help users to arrange least cost route Each Proxy Server has individual dial pl
86. t the following details MAINTENANCE gt Firmware Update The Firmware Upgrade section can be used to update to the latest firmware code to improve functionality and performance NOTE The update process takes about 2 minutes to complete and your DSL Router will reboot Please DO NOT power off your device before the update is complete Current Firmware Version GE_1 03 Upgrade Server TFTP Server IP Address Server Port leo ts 1 65535 User Name Password 0 Directory Apply Cancel Upgrade Server Select the upgrade type TFTP FTP or HTTP Server IP Address Enter the server s IP address Server Port Enter the server s port User Name Password Enter the account information for accessing the server if needed Directory Enter the location of the firmware file D Link Systems Inc 91 DVG N5402GF User s Manual MAINTENANCE 3 3 4 Dynamic DNS ADVANCED Dynamic DNS The DDNS Feature allows you to host a server Web FTP Game Server etc using a domain name that you have purchased www whateveryoumameis com with your dynamically assigned IP address Most broadband Internet Service Providers assign dynamic changing IP addresses Using a DDNS service provider your friends can enter your host name to connect to your game server no matter what your IP address is Sign up For D Link s Free DDNS service at www DLinkDDONS com Enable Dynamic DNS ryver Accres
87. t wait time PHONE 1 Hot Line Hot Line No Warm Line Hot Line Delay T 0 605 PHONE 2 Hot Line Hot Line No Warm Line Hot Line Delay 0 0 605 Hot Line Check to direct the call automatically to a pre configured destination without any action when the FXS is off hook ie as the user picks up the phone When the FXS is under Hot Line mode no other phone numbers can be dialed Hot Line No Enter the number for pre defined destination Warm Line Enter the time for the call to start with a pause so the user can dial another number The call will be automatically directed to the pre configured destination within timeout period D Link Systems Inc 62 DVG N5402GF User s Manual ADVANCED 3 2 1 10 Line ADVANCED VolP gt Line The function of Line setting is adjusting listening volume speaking volume and tone volume LINE 1 FXS Enable Listening Volume 5 3dB per step Speaking Volume 2 v 3dB per step Tone Volume 5 Min FXS Hook Flash Time 9 50 950ms Flash Time 00 l 50 950ms C Polarity Reversal FXS Chip Option 1 FXS Current 18 48ma Enable Tick the check box to enable a line If some lines are not used disable them Pause Function to avoid unnecessary waiting when an incoming call is diverting to the line Listening Volume Use the drop down menu to adjust the hearing listening volume Speaking Volume Use the drop dow
88. thre as Both RADIUS SERVER When WPA enterprise is enabled the router uses EAP 802 1x to authenticate clients via a remote RADIUS server RADIUS server IP Address RADIUS server Port 1812 RADIUS server key Select the type of WPA WPA WPA2 WPA2 Mixed choose the proper security mode according to your wireless network WPA Authentication Mode Select Enterprise RADIUS WPA Cipher Suite WPA Cipher Suite is used for the configuration of WPA or WPA2 Mixed TKIP TKIP is the security protocol used in WPA The length of TKIP encryption is longer than WEP encryption that increases the complexity of decoding for crackers AES The most powerful encryption algorithm that is commonly used in WPA WP A2 Cipher Suite WPA2 Cipher Suite is used for the configuration of WPA2 or WPA2 Mixed TKIP TKIP is the security protocol used in WPA The length of TKIP encryption is longer than WEP encryption that increases the complexity of decoding for crackers AES The most powerful encryption algorithm that is commonly used in WPA RADIUS Server RADIUS server Port Enter the port number of the authentication RADIUS server Keep the default value 1812 unless the server required change to another number RADIUS server IP Address Enter the IP address of the authentication RADIUS server RADIUS server key Enter the password such as a security Key D Link Systems Inc 33 DVG N5402GF User s Manual SETUP SETU
89. tings or queries enter 111 to seta new IP address enter 192 168 1 2 new IP address Save Settings When all setting procedures are completed dial 509 Save Settings from phone keypad Wait for about three seconds you should hear a voice prompt 1 one You can now hang up the phone and please reboot the VoIP Router to enable the new settings To inquire about the current VoIP Router WAN Port IP address setting After completing all your settings dial 101 from the keypad then you can hear the system play back the current WAN Port IP address If the system does not play back the IP address after dialing 101 this indicates that the VoIP Router currently is not connected to the Internet Please check and make sure the cable connections account numbers and passwords are correct D Link Systems Inc 106 DVG N5402GF User s Manual VoIP Router Configuration IVR 4 1 1 IVR Functions Table Function Description xample Notes Code 111 101 WAN Port IP address Set Query Dial function code 114 and then dial 172 102 WAN Port Subnet Mask SevQuey Meane IP connection then 113 103 114 104 115 105 118 121 Dial function code 114 and then dial r22 Ser PPPoE Password dP OF PPPoE connection 311 801 312 302 409 509 900 Set the IVR and the language used on the Web GUI 1 English 2 Traditional Chinese 3 Simplified Chinese D Link Systems Inc 107 DVG N5402GF User s Manual VoIP Router Configurati
90. to call through the Internet User Dial Length Enter the total number of digits that user dialed Route Select VoIP or Deny for this entry VoIP Route Profile Choose the proper Profile ID and click VoIP Route Profile to set the priority of VoIP Route Profile D Link Systems Inc 52 DVG N5402GF User s Manual ADVANCED gt VoIP Digit Map gt VoIP Route Profile Please select your VoIP priority route by phone book or Proxy server Description 1 2 3 LocalServer Server 1 None None LongDistance Server 2 Server 1 None InternationalCall Server 3 Server 2 Server 1 YoIPSTUN Server 2 None None UK Server Server 3 None None None None None None None None None None None None None None None None None E E E E Ey E E E E E ADVANCED There are 10 VolP route profiles Each VolP route profile provides four routes to select Server 1 Server 2 Server 3 Phone Book and None can be selected for each route Example of VolP Route Profile Assume that VolP TA is registered to three servers Server 1 is local VolP Service Provider Server 2 is VolP STUN free to dial to some cities without charge Server 3 is VSP in UK D Link Systems Inc 53 DVG N5402GF User s Manual ADVANCED Example 1 Single VoIP route The number translation of each server is blank The VoIP route profile appears like Description 1 LocalServer Server 1 None None None None None None None None CARYA Q
91. to register the VoIP Router with SIP proxy server or soft switch ITSP Name Enter the name of ITSP SETUP VoIP Setup FXS Representative Number registers to Proxy FXS REPRESENTATIVE NUMBER is Number 21234567 Register User ID Account Password eeeeeeeses Confirm Password eeececeses Number Enter the representative number for Line 1 and Line 2 If the VoIP Router is configured to register with SIP proxy server Line 1 and Line 2 are using this number to call through SIP proxy server It is the Caller ID for the called party when you make a VoIP call If you register the VolP Router to a SIP proxy server then it should be the number that provided by SIP proxy server Register Check the box to register with SIP proxy server User ID Account User ID Account are usually the same as Number from most SIP proxy severs Password Enter password and re enter to confirm Note Please ensure if your VoIP Service Provider allows one account for multi port using D Link Systems Inc 23 DVG N5402GF User s Manual SETUP SETUP VoIP Setup Each line registers to Proxy independently PHONE 1 FXS Number Register Invite with ID Account User ID Account Password deka Confirm Password kkk kk PHONE 2 FXS Number Register Invite with ID Account User ID Account Password EREEEKEEKK Confirm Password kkk kkk Number Enter the number text or number and te
92. vailability of a Three Way call also depends on your VoIP network Please also check with your service provider for these services D Link Systems Inc 49 DVG N5402GF User s Manual ADVANCED 3 2 1 4 Codec ADVANCED VoIP gt Codec It can set the preferred codec Jitter Buffer Silence Detection Suppression and Echo Cancellation in this section Jitter Buffer C Silence Detection Suppression Echo Cancellation Packet Approximate Enable Codec Interval Bandwidth Required ms kbps G 71i1udaw 4 20 85 6 85 6 hm G 711 adaw 5 v 20 8 Qa N z EENE k G 723 1 6 723 16 3k K i I K G 726 32K badi s A IE G 729 H lt iLBC Cy 4 lt L Jitter Buffer Enter the jitter of receiving packets Silence Detection Suppression Check the box to enable the silence packets and send less voice data package during the silent period while talking Echo Canceling Check the box to remove echo and improve voice quality during conversation RTCP XR Enable RTCP XR RFC 3611 to report network quality Codec Check the box to codec for the VoIP Gateway to support All codecs are selected and supported by default You can un check the box that is not used Codec Priority The priority of code for communication Type To set dynamic payload types of codec Packet Interval Select the frame size of voice package from different codec It define
93. ve time when log in the web interface The user will be disconnected from the web page to allow others to log in TFTP Source Port Enter the port number for sending out sends TFTP sessions Enable Web UI Check the box to enable WEB access from WAN or LAN Enable Telnet Service Check the box to enable Telnet access from WAN or LAN D Link Systems Inc 88 DVG N5402GF User s Manual MAINTENANCE 3 3 2 Backup and Restore Save and Reboot MAINTENANCE Backup and Restore SYSTEM SAVE amp REBOOT Click the button below to save and reboot the YoIP router V Save All Settings Reboot Save All Settings Click the Save All Settings check box and reboot the system after completing changes The new settings will take effect after the VolP Router is restarted Restart Click the Reboot button to reboot the system Backup Configurations File MAINTENANCE Backup and Restore SYSTEM BACKUP CONFIGURATIONS FILE Backup VoIP Router configurations file You may save your VoIP Router configurations file to a fle on your PC Note Please always save configuration file first before viewing it Backup Settings Backup Wireless Settings The current system settings can be saved as a file onto the local hard drive Click the Backup Settings button to save all current settings to a file on your PC Click the Backup Wireless Settings button to save only wireless settings to a file on your PC D Link Systems Inc 89 DV
94. vent Disable v RFC 2833 Payload Type 101 96 Volume od oy Dial Wait Timeout Enter the timeout duration after the user picks up the phone set Inter Digits Timeout Enter the timeout duration between the intervals of each key pressed When exceeding the set timeout duration without entering further digits the numbers entered will be dialed out Minimum DTMF ON Length Dial on Minimum DTMF OFF Length Dial off between tones This variable is to set the length of DTMF playback DTMF Detection Sensitivity This variable is to set the sensitivity of the telephone keys for the VoIP Router to detect the DT MF DTMF Detection Volume Sensitivity Adjust DTMF detect threshold of DTMF volume DTMF Output Volume Adjust the Tx volume of FXS port for DTMF Caller ID or Out of Band DTMF FXS Pulse Detection It allows FXS detect PULSE dial method sends from a phone set Enable Out of Band DTMF This variable is to set the method of DTMF transmission RFC2833 or SIP Info Note Out of Band DTMF transport method varies from VoIP networks please contact your VoIP provider for the preferred method Enable Hook Flash Event Select Auto RFC2833 or SIP info for the signaling method of Hook Flash Event Payload Type payload type of RFC2833 Volume Select the volume of RFC 2833 from the drop down menu D Link Systems Inc 59 DVG N5402GF User s Manual ADVANCED 3 2 1 8 Fax ADVANCED gt VoIP gt FAX The Function is auto
95. ver 2 appears like NUMBER TRANSLATION YoIP Dial Out defined here overrides Digit Map Copy From None x Scan Code YoIP Dial out 03 00453 002 00 4 o 0044 The number translation of Server 3 appears like NUMBER TRANSLATION YoIP Dial Out defined here overrides Digit Map Copy From None Scan Code VoIP Dial out 00244 0 The VolP Route Profile appears like Description 1 2 3 LocalServer Server 1 None None LongDistance Server 2 Server 1 None InternationalCall Server 3 Server 2 Server 1 None None None None None None None None None None None None None None None None None None None None None E E E E E E E E E E D Link Systems Inc 56 DVG N5402GF User s Manual ADVANCED Digit Map Table appears like Scan YVoIP Dial User Dial Code out Length YoIP Route Route Profile 09 10 YoIP 03 oIP 00244 voIP As you dial the phone numbers staring with 00244 like 00244123456789 the number will be changed to 0123456789 followed the number translation of Server3 and the call will go through Server 3 UK VSP at the first If the first route is failed the number is changed to 0044123456789 and the route is changed to Server 2 free VSP If the second route is failed the number is back to 00244123456789 and the route is changed to Server 1 local VSP Methods of Digit Map The VolP route profile appears like Description 1 2 3 LocalServer Server
96. x to enable RIP to build small multi router network via RIP protocol This function is useless for home network D Link Systems Inc 84 DVG N5402GF User s Manual ADVANCED 3 2 6 SNMP ADVANCED Advanced Network SNMP DVG N5402GF supports SNMP V1 V2 and V3 Please enter required parameter for SNMP V3 on each SNMP setting pages Simple Network Management Protocol SNMP allows a management application to retrieve statistics and status from the SNMP agent in this device C Enable SNMP Agent If the MIB browser supports SNMP V1 and V2 only please refer to following configuration Example for SNMP V2 configuration Some keys configured on MIB browser Get Community public Set Community private Trap Community public Enable Advanced gt SNMP Management gt SNMP gt Enable SNMP Agent D Link Systems Inc 85 DVG N5402GF User s Manual ADVANCED Simple Network Management Protocol SNMP allows a management application to retrieve statistics and status from the SNMP agent in this device Enable SNMP Agent C Enable Authenticate Traps Host IP Address SNMP Version Community String SNMPv3 User Name vi vi vi ivi ivi Set Advanced gt SNMP Management gt SNMP View gt View Name as all Set Advanced gt SNMP Management gt
97. xt in this field It is the Caller ID for the called party when you make a VolP call If you register the VolP Router to a SIP proxy server then it should be the number that provided by SIP proxy server Number and User ID Account are usually the same from most SIP proxy severs Each line has a number And the number of each line is not reiteration Register Check the box to register with SIP proxy server Invite with ID Account Check the box to call through SIP proxy server without registration It is always ticked when Register is also ticked Most VolP Service Providers will interdict the connection without registration User ID Account User ID Account are usually the same as Number from most SIP proxy severs Password Enter password and re enter to confirm D Link Systems Inc 24 DVG N5402GF User s Manual SETUP SETUP VoIP Setup SIP PROXY SERVER Proxy Server IP Domain 192 168 1 1 Proxy Server Port 5060 1 65535 Proxy Server Realm TTL Registration interval 600 10 7200s SIP Domain C Use Domain to Register Bind Proxy Interval for NAT i 0 1800s Initial Unregister Unregister All Contacts Keep SIP Auth Support Message Waiting Indication MWI MWI Subscribe Interval 7200 O disable 60 86400s Proxy Server IP Domain Enter the IP address or URL Uniform Resource Locator of SIP proxy server or soft switch Proxy Server Port Enter the SIP proxy server s listening p

DVG-N5402GF User`s Manual - D-Link

Contents

Download Pdf Manuals

Related Search

Related Contents