User`s Manual 4U Rackmount DVD/CD Duplicator
Contents
1. 1 Figure 4 illustrates the rear panel of the Rackmount DVD CD Duplicator The unit features an AC Power In connector an AC voltage selector and cooling fans 00000000 000000000 o 00000000 6 AC voltage selector D AC Power In connector cooling fans Figure 4 Rear Panel of the Rackmount DVD CD Duplicator AC voltage selector Use this switch to select either 115VAC or 220VAC Caution Before you turn on the power to the Rackmount DVD CD Duplicator make sure the correct voltage is selected Otherwise you risk damage to the unit The default setting is 115 VAC AC Power In connector Connect the included AC power cable to this input connector Plug the other end of the power cable into a three prong receptacle AC power outlet electrical shock or damage to the unit Caution Do not attempt to bypass the grounding plug Otherwise you risk your DVD CD Duplicator Note To ensure proper operation use only the original AC power cable with cooling fan Ball bearing fans cool the Rackmount DVD CD Duplicator Rackmount DVD CD Duplicator User s Manual Rackmount DVD CD Duplicator User s Manual Chapter 2 Using the Rackmount DVD CD Duplicator This chapter explains how to set up the Rackmount DVD CD Duplicator It also explains basic operation and menu functions Note The following instructions are2. 00 3 Figure 4 Rear Panel of the Rackmount DVD CD Duplicator 5 Figure 5 Installing the DVD CD Duplicator Rack 7 Figure 6 Copy Function on LCD Panel 8 Figure 7 How to Handle Compact Discs including DVD R and DVD RW 37 Figure 8 Ejecting the Disc Tray 0 0 eee eects 38 About This Manual This 4U Rackmount DVD CD Duplicator User s Manual explains how to operate the Rackmount DVD CD Duplicator It is divided into the following chapters Chapter 1 Introduction This chapter describes the shipping package contents and introduces the Rackmount DVD CD Duplicator Chapter 2 Using the Rackmount DVD CD Duplicator This chapter explains how to set up the Rackmount DVD CD Duplicator It also describes a basic copy operation Chapter 3 Rackmount DVD CD Duplicator Functions This chapter explains all available functions of the Rackmount DVD CD Duplicator Appendix A List of Functions Appendix A includes a complete list of all Rackmount DVD CD Duplicator functions Appendix B LCD Messages Appendix B lists all messages that may appear on the LCD display Appendix C Frequently Asked Questions FAQ Appendix C can help you to resolve technical difficulties that you might encounter Appendix D About DVD R and DVD RW Discs Appendix D contains information about handling loading and ejecting discs Appendi
3. Please refer to Chapter 2 Using the Rackmount DVD CD Duplicator on page 7 for more information Selecting 1x5 Mode one source and five target drives 1 Press buttons to select the 8 Select Source function The LCD displays the following message 8 Select Source Press the ENT button then press the buttons to select the DVD Writer source as shown below Src HDD 01 IDE1 Master Press the ENT button The LCD displays the following message HDD Selected Press the ESC button to go back to the main menu then press the buttons to select the 1 COPY function Rackmount DVD CD Duplicator User s Manual 17 9 Image The LCD displays the following message 1 COPY P A Note P Ameans Partition A To copy from this partition you must first load an image data Please refer to the section Basic Operation on page 9 in Chapter 2 for more information The Image menu consists of seven functions 9 1 through 9 7 The Image menu includes Load Delete Image Image Info Compare Image Select Image Image Src Drive and Image Format Info functions The data loaded onto the hard disk drive is called an image file 9 1 Load The factory installed hard disk drive was partitioned and formatted at the factory An alphabetical letter identifies each partition Each partition is approximately 5GB in cap
4. 186 ea bers 25 TETI Burn on the PLY ss we 25 TTA 2 Burm EA scan tole ae 26 11 13 Display Tames eae 26 11 14 Button Sound 0 ccc cece 26 TS Device H O 26 6 5 a toate ea eee 26 11 17 Quick Erase 26 18 0 e n ae alee won MRR 26 Auto Close Tray neh kek baie 26 11 20 Quick Compater ea gion ders ly 27 11 21 Audio Burn Speed Sie ead gee ba Dhue ge a 27 12 Advanced Setup Adv Setup 0 0 eect eee 27 12 1 UnderRun Protecta Be a 27 122 OM EL UID hen ci Ae Ga la ene aed dessins a 27 12 3 66 Error Skips da Co eae oe as 28 12 4 Format HDD ysis eck eet AA pele 28 12 5 Verity HDD vaca bap bebe houses ees 28 12 6 ase RBA D A ges 28 12 7 Update Firmware a Reed Se ee 28 12 8 Compare Firthwate toto
5. 22 Rackmount DVD CD Duplicator User s Manual 10 2 CD to HDD The system will then ask if you want to continue editing Continue edit next Disc No In this example we will choose not to continue 17 Press the down arrow to display No Closing the Session 18 Press the ENT button The system will ask if you want to close the session for the CD Close all disc s session Yes 19 Press the arrow buttons to display Yes then press the ENT button Once you indicate that you wish to close the session the LCD panel will display the message as follows Closing Session Please wait Note You must close the session for the CD before you can play the CD 10 2 CD to HDD The CD to HDD function enables you to select one or more tracks from an audio CD ROM disc and copy them to a specific partition on the hard disk drive Note CD R discs support up to 80 minutes of audio Therefore the number of tracks that can be copied onto a single disc depends on the length of each individual track 10 3 Play Audio Track This function is not available Rackmount DVD CD Duplicator User s Manual 23 10 4 Close Session 10 4 Close Session This function finalizes your CD R disc Once the CD R disc is finalized no more audio can be added to that disc 11 Setup The Setup menu includes a list of options that enable you to change
6. With the Quick Compare function you can specify a comparison of the source and the copied target discs in increments of 1byte through 100MB 11 21 Audio Burn Speed Use the Audio Burn Speed function to specify the write speed at which audio CDs will be recorded 12 Advanced Setup Adv Setup The Advanced Setup functions enable you to modify the system configuration You should make changes only after you become completely familiar with the functions in this menu To enter Advanced Setup mode press the ESC button for two 2 seconds until you hear a beep Then use the down arrow button to scroll through the various Advanced functions Press the ENT button to execute any of the Advanced functions To exit Advanced Setup mode press the ESC button twice then press the down arrow button The 1 Copy command will appear on LCD display 12 1 UnderRun Protect The UnderRun Protect setting turns Buffer UnderRun Protection on or off The default setting is ON 12 2 Overburn The Overburn setting turns the Overburn function in the target drive on or off The default setting is OFF For more information about Overburn discs see item 5 in the FAQ on page 35 Rackmount DVD CD Duplicator User s Manual 27 12 3 Read Error Skip 12 3 Read Error Skip The Read Error Skip setting controls error skipping during reading of the source disc If the setting is OFF and an error is detected the target drive stops an
7. If you selected partition B the LCD will display the message 1 and so on 18 Place a blank DVD R disc into each of the target drives then press the ENT button to start copying Notes With the default setting after source data has been successfully copied to the target DVD discs the DVD CD Duplicator automatically ejects the discs With the default setting if the copy operation fails the failed target DVD disc remains in the target drive To remove the failed DVD disc press the eject button on the target drive and retrieve the disc Then press the eject button again to retract the disc tray You can change the default settings by using the Advanced Setup menu See 12 Advanced Setup Adv Setup on page 27 14 Rackmount DVD CD Duplicator User s Manual Chapter 3 Rackmount DVD CD Duplicator Functions The DVD CD Duplicator features 12 functions Copy Test Test amp Copy Verify Compare Prescan Disc Info Select Source Image Edit Track Setup and Advanced Setup Each function is explained below 1 Copy The Copy function enables you to copy data from a source DVD or CD disc or a partition on the internal hard disk drive For more detailed information refer to Basic Operation on page 9 Note You can use DVD RW discs that already contain data i e DVD RW discs that are not fully blank as target discs However the data stored on the DVD RW disc will
8. During the update do not turn off the power to the unit The update process is complete after the system resets automatically and displays the main menu 28 Rackmount DVD CD Duplicator User s Manual 12 8 Compare Firmware 12 8 Compare Firmware The Compare Firmware function compares the current firmware version in the interface board to the update version in the CD or DVD disc 12 9 H W Diagnostic The H W Diagnostic function detects the devices connected to the interface board confirms functionality and displays information about the hardware on the LCD 12 10 Load Default The Load Default function resets all settings to factory default values It is recommended that you reset to the default values if the DVD CD Duplicator fails to function properly after you make changes to the original configuration To execute the Load Default function follow the steps below 1 Press and hold down the ESC button for two 2 seconds until you hear a beep 2 Press the down arrow to display 12 10 Load Default 3 Press the ENT button The system displays the message Load Default Config Yes 4 Press the ENT button The system starts loading the default data When the loading operation is complete the system displays the message Load Default OK 5 Press the ESC button twice then press the down arrow to return to the main menu The system displays 1 Copy P A Note P A means Partition A Therefore the defau
9. User Abort Cancel a job during operation Analyzing Analyze the source disc Source Drive Not Ready Source drive is not ready to read Target Drive Not Ready Target drive is not ready to write Erasing disc Source Disc Not Ready The system is erasing the data on the disc Source disc is not ready to be read Target Disc Not Ready Target disc is not ready to be written into Fail to get Drive Info Drive information cannot be obtained Fail to get SRC Disc Info Information about a source disc cannot be obtained Save new config Fail The new configuration settings cannot be saved Load Default Config Do you want to load the default settings Src amp Tgt can t in the same channel During comparison the source and target discs cannot occupy the same channel Preparing The system is preparing to record Check Target Please Wait The system is checking the target device Audio Disc Can t compare The system cannot compare the audio disc Identical Comparison results are identical Read disc error During a comparison the disc could not be read Cannot read TOC The system cannot read the contents of the disc TOC not match Comparison results are not identical Source Disc Empty The source disc contains no data Target overflow The target disc capacity is insufficient to store new data Target
10. ona Mig he de ee haa Re oe et ae 29 T29 H W Diagnostic day des sees ele dl oe bed eos one elects 29 12 10 oad Default sete aapa dee Sad 29 BARRA PS ee tS ot 30 12 5 amp ee eo eae e ited BS Cad des Bolsa a 30 12 13 USB Option gcc ee eee Sep oes eee epee ee alee Lat 30 12 14 CDaText a lente ea 30 Appendix A List of 21 Appendix LCD Messages 32 Normal Conditions ts eee dies baa a ae 32 AUGIG BiH Sc eee EAN aaa Reco Bea deat de adn 33 Appendix Frequently Asked Questions FAQ 34 BAO icp See RS we OES Phase Desa ANS wh AR 35 Appendix D About DVD R and DVD RW 37 Hand ing Dises aai bo Rca ea eee aed ede ee es 37 Loading and Ejecting Discs ssns eect 38 Appendix E Specifications 39 Appendix F Technical Support iv Rackmount DVD CD Duplicator User s Manual List of Figures Figure 1 Rackmount DVD CD Duplicator Package Contents 2 Figure 2 Front Panel of Rackmount DVD CD Duplicator Figure 3 LCD Control Panel
11. Do not attempt to bypass the grounding plug Otherwise you risk damage to the unit and electrical shock 5 Turn on the power to the DVD CD Duplicator by pressing the power button on the lower front center of the unit During initialization the DVD CD Duplicator performs a self test in which the unit s internal buffer is tested source and target drives are detected and the LCD display is tested Once the initialization is complete the DVD CD Duplicator is ready for use The LCD initially displays the Copy function by default Figure 6 Copy Function on LCD Panel 8 Rackmount DVD CD Duplicator User s Manual Basic Operation Basic Operation The Rackmount DVD CD Duplicator offers two modes of operation 1x4 mode one source optical drive and four target optical drives 1x5 mode one source hard disk drive and five target optical drives The 1x4 mode of operation is the factory default setting You can switch from 1x4 to 1x5 mode of operation and vice versa by changing the source drive setting using menu option 8 the Select Source function for more information see section 8 Select Source on page 16 This section explains these two modes of operation for the Rackmount DVD CD Duplicator 1x4 Mode Copying from the Optical Source Drive This is the factory default mode of operation You can start copying DVD CD discs by following the instructions below 1 Place your DVD CD source disc in the disc
12. The disc sessions have already been closed Burn or Move to partition Do you want to copy the data directly to disc or transfer the data to a hard disk partition Tgt overflow del last trk Disc capacity is insufficient to store the selected tracks Do you want to delete the last track Ins empty disc Continue Do you want to insert a blank disc and continue copying Rackmount DVD CD Duplicator User s Manual 33 Appendix Frequently Asked Questions FAQ The following FAQ section may help you to resolve some common problems 1 How do I reset the unit to its factory settings Refer to function 12 10 Load Default on page 29 Carefully follow the step by step instructions 2 When I tried to copy a disc the LCD displayed Source Disc Empty and the target drive s tray was ejected simultaneously What should I do The factory settings may have been changed Reset the duplicator to the factory default settings Refer to function 12 10 Load Default on page 29 Carefully follow the step by step instructions 3 What does the Target Drive Not Ready error message mean This message is displayed when one of the target drives is not ready to record because for example a blank disc is dirty or scratched Clean the target disc If it has been scratched replace it with a new one Try using a different brand of disc to make sure that the failure is not related to disc specifications or
13. following Set Partition To A If you selected partition B the LCD will display the message Set Partition To B and so on Loading Data to the Selected Partition 6 Press the ESC button to return to function menu 9 Image 7 Press the buttons to select function 9 1 Load then press the ENT button to transfer data from the DVD to the specified partition on the hard disk drive The data image file on the DVD in the source drive will be copied onto the partition you selected in Step 5 Note To help you quickly locate your data in the future it is recommended that you keep track of the data that you load into each partition 8 Once the data is loaded successfully remove the source disc from the optical drive 9 Repeat Steps through 8 to load additional image files from other DVDs to other partitions if desired At this point the selected partition is the same as the one you selected in Step 5 above If you want to copy from this partition skip to Step 12 If you want to copy an image file from another partition into which you have already loaded data continue with Step 10 Selecting a Partition from which data will be copied to discs 10 Press the buttons to select function 9 5 Select Image then press the ENT button to access the Select a Partition submenu The Select a Partition submenu also enables you to select a partition A B C etc from which you want to copy an i
14. in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on over current protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern Reliable Earthing Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit e g use of power strips A user who changes or modifies the unit or operating procedures specified herein without expressed written approval from the manufacturer will void user authority to operate the equipment Specifications and features subject to change without notice or obligation Copyright and Trademark Information Copyright 2008 TEAC America Inc All rights reserved TEAC America Inc reserves the right to modify product offerings or specifications without advanced notice No part of this publication may be reproduced in any format without the expressed written permission of TEAC America Inc TEAC and TASCAM are trademarks of TEAC Corporation All other trademarks and registered trademarks are the property of their respective owners Rackmount DVD CD Duplicator User s Manual Piracy Statement Copying or duplic
15. oes Bed wot Say 18 9 3 Image eee eel eee 18 9 A Compare UMA Ve ein vs aay ete otis dna ating FAVES Runs E EES 18 OS Select Image he Bb dS ae ee ghee eb eho Sere eee 18 9 6lmagse Src Ponce eat ete dine elie a 19 9 7 Image Format Infor seeks nh ge an aeee eee 19 10 Edit Track for CD only 0 ec cee enn ene eeee 19 T0 FED to CD Edit occ ok a a a ees ed We 19 10 2 CD to ADD ia er tae scat agri es Ce RSS RE a eee 23 10 3 Play Audio Track 2 b wt ae uly ody esas ea eee eee dees 23 10 4 Cl se Session ae espace edie oa sets ee ee 24 24 24 12 CD Burns POCO 24 3 Dass 24 24 Rackmount DVD CD Duplicator User s Manual iii Table of Contents 11 5 Auto Start Drive eces cad hie GOS RS ed Aa 24 11 6 Startup Menu ania a che gets ea bee che ee ee 25 117 Auto Verify sinner hie Re eS he ee Pete aed Ache We ee PR 25 T1 8 Auto Compatess Se tds Heke Bae ee es 25 11 9 Auto Prestam ch sca ae Patina ee Ee ee 25
16. target DVD CD disc remains in the target drive To remove the failed DVD CD disc press the eject button on the target drive and retrieve the disc Press the eject button again to retract the disc tray You can change the default settings by using the Advanced Setup menu For more information see 12 Advanced Setup Adv Setup on page 27 10 Rackmount DVD CD Duplicator User s Manual 1x5 Mode Copying from the Internal Hard Disk Drive 1x5 Mode Copying from the Internal Hard Disk Drive In this mode of operation you can copy from the internal hard disk drive to up to five 5 optical target drives The following procedure explains how to use the DVD CD Duplicator in 1x5 duplication mode During initialization see Step 3 on page 8 the DVD CD Duplicator performs a self test to detect source drives The upper right DVD RW drive and the hard disk drive will be detected as available source drives The upper right DVD RW drive is the default source drive The internal hard disk drive was formatted and partitioned at the factory Each partition occupies 5GB of hard disk space The number of partitions depends on the capacity of the hard disk drive Partitions are arranged alphabetically and initially contain no data A set of data loaded into a partition on the hard disk drive is called an image file To use the hard disk drive as the source drive in 1x5 mode you must first load an image file from a DVD onto a partit
17. the following Select Track 1 10 03 25 In this example the indicator 1 10 refers to the first 1 of 10 tracks The value 03 25 indicates the duration of the track You can press the button to display 2 for the second 2 song and so on In this example we will choose to include the first track on our mix CD 5 Select the first track then press the ENT button A plus sign will be displayed next to the 1 10 indicator as shown below Select Track 1 10 03 25 Note Pressing the ENT button again will cancel your selection 6 Press the button to display End in LCD panel as shown below Select Track End 1Trk03 25 7 Press the ENT button to finish CD editing 8 Press the buttons to display Yes End edit disc and burn Yes 20 Rackmount DVD CD Duplicator User s Manual 10 1 CD to CD Edit Copying the Track 9 Press the ENT button The system starts copying the track and displays the copying information as follows Copying 24X Edit 1 10 gt 1 1 In the display above the 1 1 indicator refers to the first track selected 1 out of the total number of tracks selected 1 When the copy process is complete the LCD panel displays the following message Burn Complete OK 01 The system will ask if you want to keep editing 10 To continue editing press the butto
18. tray of the source drive The source drive is located in the upper right corner of the unit Refer to Figure 2 on page 3 2 Switch to function 1 Copy by pressing the buttons if necessary Refer to Figure 6 on page 8 3 Place a blank DVD CD disc into as many of the target drives as you desire then press the ENT button to start copying Note The type and capacity of the target disc s must match that of the source disc For example if the source disc is a CD ROM then the blank target disc s must be CD R disc s If the source disc is a4 7GB DVD ROM disc then the blank target disc s must be 4 7GB DVDER If the source disc is an 8 5GB Dual Layer DL disc then the blank target disc s must 8 5GB DVD R DL You do not need to insert a DVD disc into every available target drive You can make fewer copies if you prefer The internal controller will automatically detect inserted discs and issue the record command to only those target drives that contain a blank disc When the copy operation is complete the DVD CD disc in each of the target drives will be ejected automatically Rackmount DVD CD Duplicator User s Manual 9 1x4 Mode Copying from the Optical Source Drive Notes With the default setting after a source disc has been successfully copied the DVD CD Duplicator automatically ejects the target DVD CD discs Q With the default setting if the copy operation fails the failed
19. 4U Rackmount DVD CD Duplicator User s Manual Models TASCAM DV W14R TASCAM Safety Precautions Rackmount DVD CD Duplicators are high precision electronic devices Do not use them in any manner other than as specified in this manual Please read this manual in its entirety before you begin the installation procedure Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous laser exposure To prevent fire or shock do not expose the unit to moisture or rain To prevent electrical shock do not attempt to disassemble the DVD CD Duplicator Refer servicing to authorized personnel Rackmount DVD CD Duplicators drives utilize a laser beam that can be harmful to your eyes Do not disassemble the cabinet or unit Do not attempt to look through the front panel or into the unit while the power is turned on Elevated Operating Ambient If the unit is installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than the room ambient temperature Therefore consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature Tma specified by the manufacturer Reduced Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised Mechanical Loading Mounting of the equipment
20. Audio Track 10 4 Close Session 11 Setup 11 1 Language Default is English 11 2 CD Burn Speed Default is Auto 11 3 DVD Burn Speed Default is Maximum 11 4 Read Speed Default is Maximum 11 5 Auto Start Drive Default is Off 11 6 Startup Menu Default is Copy 11 7 Auto Verify Default is Off 11 8 Auto Compare Default is Off 11 9 Auto Prescan Default is Off 11 10 Eject Disc Default is Eject Good Only 11 11 Burn on the Fly Default is On 11 12 Burn Mode Default is DAO 11 13 Display Time Default Off 11 14 Button Sound Default is On 11 15 Device Info 11 16 System Info 11 17 Quick Erase 11 18 Full Erase 11 19 Auto Close Tray 11 20 Quick Compare 11 21 Audio Burn Speed 12 Advanced Setup Adv Setup 12 1 UnderRun Protect Default is On 12 2 Overburn Default is Off 12 3 Read Error Skip Default is Off 12 4 Format HDD factory use only 12 5 Verify HDD factory use only 12 6 Burn in 12 7 Update Firmware 12 8 Compare Firmware 12 9 H W Diagnostic 12 10 Load Default 12 11 CD G Default is Off 12 12 ISRC amp MCN Default is Off 12 13 USB Option 12 14 CD Text Default is Off Rackmount DVD CD Duplicator User s Manual 31 Appendix LCD Messages This appendix explains the messages that may appear on the LCD panel Normal Conditions Message Meaning Initialize SDRAM Initialize system memory Detect drives Detect the drives connected to the system
21. DVD R DL Figure 8 Ejecting the Disc Tray 38 Rackmount DVD CD Duplicator User s Manual Appendix E Specifications The following table lists the product specifications for the Rackmount DVD CD Duplicator MODEL gt DV W14R LCD Panel Logo TASCAM HDD Capacity 160GB DVD Recorders 20X DVD RW Read Speed DVD 16x CD 48x Write Speed DVD 20x CD 48x Drive Buffer Size 2MB System Buffer Size 128MB Supported Discs DVD R DVD RW DVD DL DVD R DVD RW DVD R DL CD R and CD RW System Control Copy and Search Buttons System Display LCD Panel LED Indicator Write Method Auto Detect DAO TAO Operation Mode Copy Test Scan Compare Firmware Upgrade Via CD ROM DVD ROM Weight 50 Ibs Dimensions 7 inches H x 17 inches W x 18 inches D Environment 5 C to 35 C Power Supply AC Input 100 240V Agency Certification UL and FCC Rackmount DVD CD Duplicator User s Manual 39 Appendix F Technical Support For technical support please contact the TEAC and TASCAM Support Center Technical Support Telephone 323 727 4860 Fax 323 869 8751 Monday Friday 8 00 am to 12 00 pm and 1 00 pm to 5 00 pm PST http www teac com support E mail dspdtsg teac com DV W14R 081217 40 Rackmount DVD CD Duplicator User s Manual
22. Disc Not Empty The target disc still contains data Press a Key to Eject Good Disc Press any key to eject a disc after copying Copy suc cessful Press a key to Eject Fail Disc Press any key to eject a disc after copying Copy failed DVD RW does not Support the Func DVD RW does not support this function Hold ESC to exit Press ESC for one second to terminate the test All data will be lost erase All data on the disc will be lost Confirm erasure request Erase Finished The erasing of the data is complete No Erasing to Disc in DVD RW The disc in the DVD RW drive is not rewritable 32 Rackmount DVD CD Duplicator User s Manual LCD Messages Message Meaning HDD not Format The hard disk has not been formatted Format HDD Do you want to format the hard disk All data will be lost format All data on the hard disk will be lost Confirm the format request Format HDD Formatting of the hard disk is complete Image load OK The image has been successfully loaded from DVD to the hard disk Image load Fail The image has not been loaded successfully from DVD to the hard disk HDD too small to handle image The hard disk capacity is insufficient to store the data image at least 5Gbytes is required No Valid HDD The system cannot locate a hard disk HDD too small The hard disk capac
23. Target Overflow message mean This message may be displayed when the source master CD disc contains data music in excess of the 70OMB 80min disc capacity These types of discs are often called Overburn discs Attempting to copy an Overburn disc might generate read errors at the end of the disc making the disc unreadable in regular CD readers Although this type of recording is not recommended this unit is capable of duplicating Overburn discs Refer to 12 Advanced Setup Adv Setup on page 27 for more information Then execute function 12 2 Overburn on page 27 to change the setting to the ON state Follow the instructions to exit the Advanced Setup first and then execute the 1 Copy function This time the unit will again display the message and prompt you to continue Press the ENT button to create an Overburn copy This message may be displayed when a source DVD disc is copy protected such as a purchased rented DVD movie game There is no Duplicator on the market that can copy these discs as doing so is a violation of Federal law Replace the source DVD disc with a non copy protected disc This message may also be displayed if the Source DVD disc has a capacity larger than the DVD disc in the target drive Make sure that both source and target discs have the same capacity For example if the source DVD disc is an 8 5GB capacity disc make sure the target DVD disc is also an 8 5GB disc 6 What media is reco
24. acity The number of partitions depends on the capacity of the hard disk drive The Load function enables you to transfer data from the source DVD Writer drive to the current partition of the hard disk drive Note P A stands for partition A You can load as many disc images as the number of partitions available on the hard disk drive 9 2 Delete Image Use the Delete Image function to delete an image stored in a particular partition 9 3 Image Info Use the Image Info function to display basic information for an image file stored in a particular partition 9 4 Compare Image Use the Compare Image function to compare the contents of a disc in the source DVD Writer with the image file in the partition 9 5 Select Image The internal hard disk drive was partitioned and formatted at the factory An alphabetical letter identifies each partition Each partition is approximately 5GB in capacity The number of partitions depends on the capacity of the hard disk drive Use the Select Image function to select an image file that is stored in a specific partition on the hard disk drive 18 Rackmount DVD CD Duplicator User s Manual 9 6 Image Src Drive 9 6 Image Src Drive Use the Image Src Drive function to select the DVD Writer drive as the source from which you can load data into a particular partition as an image file 9 7 Image Format Info The partitions on the hard disk drive can be configured to store a CD 1GB DVD 5GB or a Do
25. anual 25 11 12 11 12 Burn Mode The Burn Mode setting enables you to select from two writing methods for CD R media e Disc At Once DAO e Track At Once TAO DAO is the default setting 11 13 Display Time The Display Time function displays the total time of each copy operation The default setting is OFF 11 14 Button Sound The Button Sound setting turns the button sound on or off The default setting is ON 11 15 Device Info The Device Info function displays information for both the source and target drives 11 16 System Info The System Info function displays information for the interface board 11 17 Quick Erase The Quick Erase function performs a Quick Erase on DVD RW discs 11 18 Full Erase The Full Erase function performs a Full Erase on DVD RW discs This function takes longer than the Quick Erase 11 19 Auto Close Tray The Auto Close Tray setting function closes the DVD writer s tray automatically after the recording is completed and the disc has been ejected It is related to function 11 5 Auto Start Drive 26 Rackmount DVD CD Duplicator User s Manual 11 20 Quick Compare If you have not set any DVD writer to copy using function 11 5 the Auto Close Tray function will be invalid If function 11 5 is valid you can set for the writer s tray to close automatically after copying finishes You can specify tray closure to occur within 5 to 50 seconds 11 20 Quick Compare
26. applicable to TEAC and TASCAM branded Rackmount DVD CD Duplicators The primary differences between models are the TEAC or TASCAM logo on the LCD Control Panel and the model number on the corresponding nameplate label Please refer to Specifications on page 39 for detailed information on your model Setup 1 Carefully remove the DVD CD Duplicator unit AC power cord warranty card optional rubber feet and user s manual from the shipping box Note Please keep the original box and packaging materials for use in the event of future storage or transportation of the unit If the unit will not be mounted onto a rack you may wish to affix the four included rubber feet to the bottom of the Rackmount DVD CD Duplicator Then skip Step 3 and proceed directly to Step 4 To rack mount the DVD CD Duplicator leave a 1U of space above it and 4 inches 10cm or more of space at the rear Use a rack mounting kit not included to mount the unit in a standard 19 inch equipment rack as illus trated below If rubber feet are currently affixed to the bottom of the unit remove the rubber feet before you attempt to mount the unit in a rack Figure 5 Installing the DVD CD Duplicator in a Rack Rackmount DVD CD Duplicator User s Manual Setup 4 Connect one end of the included power cable to the back of the DVD CD Duplicator Connect the other end of the power cable to a three prong recep tacle AC outlet Caution
27. ating copyrighted materials including audio compact discs CDs and DVD movies without the permission of the copyright holder constitutes theft of intellectual property It is a serious crime and a violation of Federal law Do not use the TEAC or TASCAM Rackmount DVD CD Duplicator or any equipment to copy or duplicate copyrighted digital audio video photographs images text software or other digital information without the permission of the copyright holder TEAC and TASCAM accept no responsibility for copyright infringement or misuse of this equipment It is the sole responsibility of the user to use the equipment within the limits prescribed by law and to respect the legal copyrights of all copyright owners FCC Radio Frequency Interference Regulations Warning This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions contained in this manual may cause harmful interference to radio and television communications This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Subpart B of Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which ca
28. be erased automatically before the new data is copied No special setting or procedure is required to erase the old data 2 Test The Test function simulates writing to the target disc Discs will remain blank after the test is complete This function is recommended if you are using unsupported media This function enables the target drive to adjust its laser to the proper intensity Note Unexpected termination or cancellation of a test will not affect a target DVD R disc The target DVD R disc will remain blank and available for use However DVD RW discs that contain data be damaged and the data they contained may be rendered unrecoverable It may be necessary to re start the DVD CD Duplicator if the target drive hangs during a sudden termination 3 Test amp Copy The Test amp Copy function performs the test simulation and the copy process in one step The copy process is performed only if the simulation detects no problems If the simulation fails the copy process is cancelled 4 Verify The Verify function verifies that the target disc was written completely and with no errors Rackmount DVD CD Duplicator User s Manual 15 5 Compare 5 Compare The Compare function compares data on the source and target discs after the copy process is complete Note This function works only with data discs 6 Prescan The Prescan function is performed on the source drive This function scans the dis
29. c to determine the maximum data audio extraction speed 7 Disc Info The Disc Info function displays detailed information about the source disc including sessions tracks capacity etc 8 Select Source The Select Source function enables you to select a drive DVD Writer or hard disk drive as the source from which to copy If you select the DVD Writer as the source the unit will work as a 1x4 DVD CD Duplicator one source optical drive and four target optical drives If you select the internal hard disk drive the unit will work as a 1x5 DVD CD Duplicator one source hard disk drive and five target optical drives Selecting 1x4 Mode one source and four target drives 1 Press the buttons to select 8 Select Source function The LCD displays the following message 8 Select Source 2 Press the ENT button then press the buttons to select the DVD Writer source as shown below Src Super Multi 00 IDEO Master Be sure to select drive 00 IDEO This is the drive in the upper right corner of the unit 16 Rackmount DVD CD Duplicator User s Manual Selecting 1x5 Mode one source and five target drives Press the ENT button The LCD displays the following message S Multi Selected Press the ESC button to return to the main menu then press the buttons to select the 1 COPY function The LCD displays the following message 1 COPY
30. ce aie WES oe wetted ees 3 Rear Pan l tems tle teeth eh on Bs ee AS eee RES thie 5 Chapter 2 Using the Rackmount DVD CD Duplicator 7 SetuP aaa Gy out ave thes Seats Simla AE OE E qi Basic Operation ae ee eee ee ae ae 9 1x4 Mode Copying from the Optical Source Drive 9 1x5 Mode Copying from the Internal Hard Disk Drive 11 Chapter 3 Rackmount DVD CD Duplicator Functions 15 suet tras dae tgs eRe ett ata din obra arenes See 15 DOSE pant cpa tata think A dete Sele elie lnk 15 3 Test COPY nh tee al ona Gace Sues Paine SA 15 EDan a ee 15 D Compares pea mena 16 6 Prescai wiih sete phe Sa OS taken Ae das 16 T Disc Infon o eee ik Seka behd ele che aan gee tena Soe ee bed 16 S Select Sources re gia BRN Setar ate tenets 16 Selecting 1x4 Mode one source and four target drives 16 Selecting 1 5 Mode one source and five target drives 17 see S eae he ean wl eles gin 18 18 92 Delete ty ees
31. d displays the read error message If the setting is ON no messages will be displayed if an error occurs The copy operation will be completed and the copy will include all errors detected during the process The default setting is OFF 12 4 Format HDD For factory use only please do NOT use this function Warning Do not run this function It will erase all data already loaded into disk partitions This function is reserved for factory use only The factory installed hard disk drive has already been partitioned and formatted and is ready for use 12 5 Verify HDD For factory use only please do NOT use this function Warning Do not run this function It will erase all data already loaded into disk partitions This function is reserved for factory use only The factory installed hard disk drive has already been partitioned and formatted and is ready for use 12 6 Burn in The Burn in function runs an emulate writer function continuously The disc in the target drive is ejected and re inserted automatically between each test cycle This function can be prepared to run continuously or specified to run from to 1000 times 12 7 Update Firmware The Update Firmware function updates the firmware of the interface board via a CD or DVD disc The disc must contain the required data file and be inserted in the source drive The DVD CD Duplicator will locate the data and update its firmware automatically
32. d five target drives this drive serves as an additional target drive and the internal hard disk drive functions as the source drive Refer to Chapter 2 Using the Rackmount DVD CD Duplicator on page 7 for more details Insert the disc to be copied into the source drive Use the disc tray to load a DVD or CD into the drive You can open the tray by pressing the Load Eject button if the tray fails to open you can use the emergency eject mechanism You can close the tray by pressing the Load Eject button Note It is strongly recommended that you do not push the tray in to close it Please press the Load Eject button to eject or retract the tray See Figure 8 on page 38 5 target drives In 1x4 mode there is one 1 source drive and four 4 target drives In 1x5 mode there is one 1 source drive and five 5 target drives Refer to Chapter 2 Using the Rackmount DVD CD Duplicator on page 7 for more details Insert a blank disc into each target drive to make a copy of the source disc You can open the tray by pressing the Load Eject button if the tray fails to open you can use the emergency eject mechanism You can close the tray by pressing the Load Eject button Note It is strongly recommended that you do not push the tray in to close it Please press the Load Eject button to eject or retract the tray See Figure 8 on page 38 4 Rackmount DVD CD Duplicator User s Manual
33. d user who requires speed and accuracy You can set up your Rackmount DVD CD Duplicator very quickly and easily There is no need to install any software There is no need to attach any cables to your computer The Rackmount DVD CD Duplicator functions entirely as a stand alone unit Caution Your Rackmount DVD CD Duplicator can operate on either 115VAC or 220VAC voltage Before you turn on the power to the unit be certain to select the correct voltage for your region by setting the AC Voltage Selector on the rear panel Failure to do so can result in damage to the unit For more information refer to page 5 Rackmount DVD CD Duplicator User s Manual 1 Rackmount DVD CD Duplicator Package Contents Rackmount DVD CD Duplicator Package Contents Your Rackmount DVD CD Duplicator package includes the following items see Figure 1 TEAC TASCAM Rackmount DVD CD Duplicator unit AC power cable Rackmount DVD CD Duplicator System User s Manual this booklet Warranty card not shown Optional rubber feet not shown User s Manual Rackmount DVD CD Duplicator Figure 1 Rackmount DVD CD Duplicator Package Contents Note If any of the items above is missing from your package upon purchase please contact your vendor immediately Rackmount DVD CD Duplicator User s Manual Front Panel Front Panel Figure 2 i
34. dges to avoid getting fingerprints on the surface of the disc Do not touch the disc s data surface unlabeled side Do not place discs in direct sunlight or in locations subject to high humidity high temperatures or dusty conditions If it becomes necessary to clean a disc due to erratic operation visible dust or smudges gently wipe the surface of the disc from the center to the outside edge Do not use benzene alcohol thinner or other solvents wipe disc surface from handle discs center to outside edge by their edges Figure 7 How to Handle Compact Discs including DVD R and DVD RW Rackmount DVD CD Duplicator User s Manual 37 Loading and Ejecting Discs Loading and Ejecting Discs To load a disc into the source or a target drive first open the disc tray by pressing the Load Eject button on the front of the drive Place the disc on the disc tray with its label side facing up Then press the Load Eject button again to retract the disc tray back into the drive To eject a disc from the source or a target drive press the Load Eject button on the front of the drive to extend the disc tray Remove the disc from the disc tray and place it in its protective case Then press the Load Eject button again to retract the disc tray back into the drive Press the Load Eject button to extend and retract the disc tray
35. he Startup Menu setting enables you to select a menu item to be displayed as the first menu item when you turn on the DVD CD Duplicator COPY is the default 11 7 Auto Verify The Auto Verify setting controls auto verification of discs after a copy operation The default setting is OFF 11 8 Auto Compare The Auto Compare setting controls auto comparison of data between source and target discs after a copy operation The default setting is OFF 11 9 Auto Prescan The Auto Prescan setting controls automatic prescan of the source disc whenever a data audio disc is inserted in the optical source drive 1x4 mode of operation The default setting is OFF 11 10 Eject Disc The Eject Disc setting controls the ejection of discs by the target drive Three options are available e Eject Good Only This option ejects only successfully copied discs This is the default setting e Eject All Disc This option ejects successful and failed copy discs e Do Not Eject With this option all discs remain in the target drive Manual ejection is required after every copy operation 11 11 Burn on the Fly The Burn on the Fly function enables you to control the copy operation When the setting is ON data is copied directly from the source DVD to the target DVDs When the setting is OFF the DVD CD Duplicator first loads the data into a partition on the hard disk drive then copies the data to the target DVDs Rackmount DVD CD Duplicator User s M
36. ion on the hard disk drive select the partition that contains the data you want to copy specify the hard disk drive as the source drive then execute the copy function 1 Insert a source DVD into the source drive This disc DVD ROM or DVD contains the data that you wish to copy to the partition on the internal hard disk drive Selecting a Partition to which you will copy data 2 Press the buttons to select function menu 9 Image then press ENT button The Image menu includes the Load Delete Image Image Info Compare Image Select Image Image Src Drive and ImageFormat Info functions 3 Press the buttons to select function 9 5 Select Image then press the ENT button to access the Select a Partition submenu The Select a Partition submenu enables you to select a partition A B C etc into which to load an image file on the hard disk drive When the unit is shipped from the factory the partitions on the hard disk drive contain no data The LCD will display a message similar to the following for each corresponding partition Select a Partition No image in A Rackmount DVD CD Duplicator User s Manual 11 4 Press the buttons to select the desired partition letter The LCD will display partition A as the first option but you can select any partition letter at any time 5 Press the ENT button to confirm the desired partition The LCD will display a message similar to the
37. ity is too small No Image in Partition xx There is no data image in the specified partition Image Exists Overwrite The current partition contains a data image Confirm the overwriting request Delete Image in Partition xx Confirm the request to delete the data image in the spec ified partition Partition Damage The partition is damaged Verify Disk Or Partition Do you want to verify the entire hard disk or only a parti tion Verify Hard Disk OK The hard disk has been verified successfully Verify the Hard Disk Fail The hard disk has not been verified successfully Verify Partition Header Verify the partition header Select HDD First First select a formatted hard disk Audio Editing Message Meaning Lost selected Tracks Abort and delete the selected tracks End edit disc and burn Continue edit next Disc Finish the music disc editing and start to copy Do you want to continue the music disc editing Target Overflow Re Select The disc capacity is insufficient to store the selected tracks Please select fewer tracks Close all disc s session Confirm the closing of disc sessions Can t edit HDD The hard disk cannot be edited as a source audio disc NO AUDIO track in this disc The source disc contains no audio tracks Insert next disc Insert the next audio disc Sessions were closed already
38. llustrates the front panel of the Rackmount DVD CD Duplicator power switch LED power indicator 3 LCD control panel source drive 5 target drives Figure 2 Front Panel of Rackmount DVD CD Duplicator power switch Use the power switch to turn the power to the DVD CD Duplicator unit on or off 2 LED power indicator The LED power indicator will be continuously lit when the DVD CD Duplicator power is on LCD control panel Use the control panel buttons to navigate through the various functions viewed on the LCD display Figure 3 LCD Control Panel Rackmount DVD CD Duplicator User s Manual 3 Front Panel The DVD CD Duplicator control panel features an LCD display and four buttons These buttons are described in the following table Press the Up arrow button to scroll up functions or menus Press the Down arrow button to scroll down functions or menus ENT Press the ENT Enter button to execute a selected function Press the ESC Escape button to cancel a selected function or to return to the main menu source drive This drive is the source drive when the DVD CD Duplicator is being used in 1x4 mode one source drive and four target drives In 1x5 mode one source drive an
39. lt setting for the Duplicator is 1x5 mode one source hard disk drive and five target optical drives If there is no data in Partition A change the setting to 1x4 mode one source optical drive and four target optical drives Please refer to the Select Source function on page 16 Rackmount DVD CD Duplicator User s Manual 29 12 11 CD G 12 11 CD G The CD G function enables or disables CD G karaoke CD format support The default setting is OFF Note The CD G value must be set to OFF before you can use the Track Extraction features For more information about CD G discs see item 7 in the FAQ on page 35 12 12 ISRC amp MCN The ISRC amp MCN function enables or disables ISRC and MCN format support The default setting is OFF 12 13 USB Option The USB Option function is not applicable to Rackmount DVD CD Duplicators 12 14 CD Text The CD Text function enables or disables the copying of CD Text discs The default setting is OFF For more information about CD Text discs see item 8 in the FAQ on page 35 30 Rackmount DVD CD Duplicator User s Manual Appendix A List of Functions 1 Copy 2 Test 3 Test amp Copy 4 Verify 5 6 Prescan 7 Disc Info 8 Select Source 9 Image 9 1 Load 9 2 Delete Image 9 3 Image Info 9 4 Compare Image 9 5 Select Image 9 6 Image Src Drive 9 7 ImageFormat Info 10 Edit Track for CD only 10 1 CD to CD Edit 10 2 CD to HDD 10 3 Play
40. mage file 12 Rackmount DVD CD Duplicator User s Manual 11 12 1x5 Mode Copying from the Internal Hard Disk Drive Press the buttons to select partition you wish to copy from then press the ENT button The data will be copied from the selected partition when you specify the hard disk drive as the source and execute the copy function as described in Steps 13 through 16 Press the ESC button twice to exit to the DVD CD Duplicator s main menu Selecting a Source Drive 13 14 15 16 Press the buttons to select 8 Select Source function The LCD displays the following message 8 Select Source Press the ENT button then press the buttons to select the DVD Writer source as shown below Src HDD 01 IDE1 Master Press the ENT button The LCD displays the following message HDD Selected The hard disk drive is now designated as the source drive Press the esc ESC button to go back to the main menu g Copying Data from the Hard Drive to Target Discs 17 Press the buttons to switch to function 1 Copy The LCD will display a message similar to the following 1 Copy This message indicates that the data will be copied from the hard disk drive s partition A which was selected in Step 11 Rackmount DVD CD Duplicator User s Manual 13 1x5 Mode Copying from the Internal Hard Disk Drive
41. mmended For best results brand name media is recommended for example Memorex Imation TDK Verbatim Fuji Film etc 7 How do I copy a CD G Karaoke disc The CD G feature is set to OFF as a default Refer to 12 Advanced Setup Adv Setup on page 27 for more information Then execute function 12 11 CD G on page 30 to change the setting to the ON state Follow the instructions to exit the Advance Setup first and then execute the 1 Copy function 8 How do I copy a CD Text disc The CD Text feature is set to OFF as a default Refer to 12 Advanced Setup Adv Setup on page 27 Then execute function 12 14 CD Text on page 30_to change the setting to the ON state Follow the instructions to exit the Advance Setup first and then execute the 1 Copy function Rackmount DVD CD Duplicator User s Manual 35 9 do I extract audio tracks from different CD discs to create compilation audio CD On the main menu go to function 10 Edit Track and press the ENT button Press the ENT button to execute the 10 1 CD to CD Edit function Follow the step by step instructions described on page 19 36 Rackmount DVD CD Duplicator User s Manual Appendix D About DVD R and DVD RW Discs This appendix explains how to handle load and eject compact discs including DVD R and DVD RW discs Handling Discs Handle compact discs including DVD R and DVD RW discs only by their e
42. n be determined by turning the equipment off and on the user may try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Move the device and the receiver further apart e Connect the equipment to an electrical outlet on a different circuit than the receiver e Consult the dealer or an experienced audio television technician Also the following booklet may prove helpful How to Identify and Resolve Radio TV Interference Problems It is available from the U S Government Printing Office Washington D C 20402 stock number 004 000 00345 4 The user is cautioned that any changes or modifications not expressly approved by TEAC America Inc could void the user s warranty ii Rackmount DVD CD Duplicator User s Manual Table of Contents Safety Precautions Hole ge Hea his ceed eee eas i Copyright and Trademark Information 8 i Piracy Statement 2 e caw cals ods aden else en ihe tet EREDE Genk ii FCC Radio Frequency Interference Regulations ii Bist Of gt Mate A eke ced E EE E About This ea eee pyar reseed Goer Chapter 1 Introduction 1 Rackmount DVD CD Duplicator Package Contents 2 Front Panel 2c s
43. ns to display Yes as shown below Continue edit next Disc Yes If you choose not to continue select No then skip to Step 18 Selecting a Track from the Second CD 11 Press the ENT button The current source CD will eject automatically and the system will ask you to insert another source CD Insert next disc 12 Insert a different source CD then press the ENT button to begin the track selection process On this disc we will select the second track Rackmount DVD CD Duplicator User s Manual 21 10 1 CD to CD Edit 13 Press the down arrow to display Track 2 on LCD panel then press the ENT button The LCD panel will display a plus sign beside the 2 10 indicator as shown below Select Track 2 10 04 25 14 Press the up arrow to display End in the LCD panel as shown below Select Track End 1Trk04 25 15 Press the ENT button to finish the CD editing and then press the buttons to display Yes End edit disc and burn Yes Copying the Track 16 Press the ENT button The system starts copying the track and displays the following copying information Copying 24X Edit 2 10 gt 2 2 The indicator 2 2 represents the second 2 of the two 2 tracks we selected from different discs When the copy process is complete the LCD panel displays the following message Burn Complete OK 01
44. quality You may also encounter this problem if you try to use a disc that is not blank The Rackmount DVD CD Duplicator accepts only blank DVD CD discs in the target drives This message may also be displayed if the source disc is copy protected In such a case insert a disc that is not copy protected In accordance with applicable laws the Duplicator is designed to be unable to bypass any copy protection technology that may be encoded on the source disc If the error message continues to appear even with different target or source discs contact our Technical Support Group 4 What does the Source Drive Not Ready message mean This message is displayed when the source upper drive is not ready to read because for example the master disc is dirty or scratched Clean the source disc If it is scratched use a different source disc The message may also be displayed if the source disc is empty Be sure to insert a data music video disc in the source drive This message may also be displayed if the source disc is copy protected In such a case insert a disc that is not copy protected In accordance with applicable laws the duplicator unit is designed to be unable to bypass any copy protection technology that may be encoded on the source disc If the error message continues to appear even with different source discs contact our Technical Support Group 34 Rackmount DVD CD Duplicator User s Manual 5 What does the
45. the original default configuration Various settings are available under the Setup menu that control the operation of the DVD CD Duplicator However it is recommended that you use the original default settings for optimal operation 11 1 Language The DVD CD Duplicator LCD panel can display text in English and Spanish The Language function enables you to select the display language English is the default option 11 2 CD Burn Speed The CD Burn Speed setting controls the writing speed of the target drive when recording onto CD R CD RW media The default value is AUTO which writes at the highest speed allowed by the media 11 3 DVD Burn Speed The DVD Burn Speed setting controls the writing speed of the target drive when recording onto DVD RW media The default value is MAXIMUM which writes at the highest speed available on the target drive On occasion using the maximum writing speed will cause copy failure due to poor quality DVD RW discs In this case it is recommended that you reduce the writing speed 11 4 Read Speed The Read Speed function enables you to set the reading speed of the target drive MAXIMUM is the default setting 11 5 Auto Start Drive The Auto Start Drive setting enables the DVD CD Duplicator to auto start the copy or test process as soon as a blank disc is inserted into the target drive The default setting is OFF 24 Rackmount DVD CD Duplicator User s Manual 11 6 Startup Menu 11 6 Startup Menu T
46. uble Layer DL 10GB image The factory partitions the hard disk drive for DVD images at 5GB per partition Use the Image Format Info function to verify this setting 10 Edit Track for CD only The Edit Track functions enable you to create and copy a collection of songs from different audio discs Note The CD G value must be set to OFF before you can use the Track Extraction feature For more information refer to 12 Advanced Setup Adv Setup on page 27 10 1 CD to CD Edit You can use this function to copy tracks from one or more discs and burn them to a CD R This function works only in the 1x4 mode of operation The CD to CD Edit function enables you to select specific tracks from various audio discs combine them to create a collection of songs and copy the collection to blank CD R CD RW discs Note CD R discs support up to 80 minutes of audio Therefore the number of tracks that can be copied onto a single disc depends on the length of each individual track 1 Insert a source disc into the source optical drive and a blank CD R disc into the target drive 2 Switch to function 10 1 CD to CD by pressing the button 3 Press the ENT button The LCD panel displays the following 10 01 Edit Track CD to CD Edit Rackmount DVD CD Duplicator User s Manual 19 10 1 CD to CD Edit Selecting a Track from the First CD 4 Press the ENT button again The LCD panel displays
47. x E Specifications Appendix E includes technical specifications for the Rackmount DVD CD Duplicator Appendix F Technical Support Appendix F explains how to contact technical support for your Rackmount DVD CD Duplicator Rackmount DVD CD Duplicator User s Manual v vi Rackmount DVD CD Duplicator User s Manual Chapter 1 Introduction Thank you for purchasing a TEAC or TASCAM 4U Rackmount DVD CD Duplicator Note This User s Manual is intended for both TEAC and TASCAM branded Rackmount DVD CD Duplicators Operational instructions for both models are essentially the same The primary differences between the models are the TEAC or TASCAM logo on the LCD control panel and the name plate on the rear panel The Rackmount DVD CD Duplicator is a stand alone disc to disc DVD CD Duplicator system that does not require connection to a computer It can duplicate a single master DVD R to DVD R media at up to 20X speeds resulting in an exact replica of a 4 7GB disc It can duplicate discs to CD R CD RW media at up to 48X 32X speeds respectively It can also duplicate discs to DVD R DL media The Rackmount DVD CD Duplicator is designed to perform DVD and CD copying quickly and accurately The Rackmount DVD CD Duplicator automatically identifies source DVD formats and replicates the content as required The Rackmount DVD CD Duplicator performs continuous copying with no waiting It is an ideal DVD CD Duplicator for the advance
Download Pdf Manuals
Related Search